Search Documents

By Jinxing Ji

Several fundamental aspects related to the nickel electrowinning from chloride electrolytes have been addressed in this paper. The thermodynamic study includes the activity coefficient of the hydrogen ion and the speciation diagram of NiCI2 solutions. The activity coefficient of the hydrogen ion (YH+) was calculated and estimated experimentally using a combination glass pH electrode. It was found that YH+ was greater than one in concentrated NiCl2 solutions and increased significantly with increasing NiCl2 concentration. The speciation diagram for NiCl2 solutions was plotted with YH+ and the effect of the ionic strength on the equilibrium constants being taken into account. It was discovered that the predominant nickel species in the acidic region were Ni2+ and NiCI+ in 0.937 M NiCl2 solution at 25°C. Electrodeposition tests demonstrated that higher Nit' concentration in the electrolyte improved the current efficiency of nickel electrodeposition (CENi). The additions of H3BO3, and NH4Cl increased very little the current efficiency of nickel electrodeposition at pH 1.5 and temperature 60°C. However, the addition of sulfate decreased the current efficiency of nickel electrodeposition. Nickel electrodeposition was also found to be a steady-state process since the amount of acid added to the electrolyte at a constant pH increased linearly with time during galvanostatic electrodeposition. The cathode surface pH during nickel electrodeposition was measured using a flat-bottom combination glass pH electrode and a 500-mesh gold gauze as cathode. The cathode surface pH was found always to be higher than the pH in the bulk electrolyte, and if the current density was sufficiently large, it would eventually reach a level causing precipitation of insoluble Ni(OH)2(s) on the cathode surface. Rotating disc electrode studies revealed that the rate of nickel electrodeposition was first order with respect to the activity of nickel ion and zero order with respect to the activities of chloride and hydrogen ions. The rate of hydrogen evolution was found to be first order with respect to the activity of hydrogen ion and to be zero order with respect to the activities of nickel and chloride ions. These findings indicate that nickel deposition and hydrogen evolution proceed independently.

Jan 1, 1995

By Paulo von Krüger

This paper deals with the cell design and operation of a tin electrorefining 1:5 pilot plant. The purpose of the work was the fitting of the basic parameters to be used in a full-scale tankhouse from a major Brazilian tin producer. The main specific difference was the use of permanent stainless steel cathodes instead of conventional tin starting sheets. The results of both product quality and operating parameters are discussed.

Jan 1, 2003

ABSTRACT The SART (sulphidization, acidification, recycle, and thickening) process is an effective way to separate copper and cyanide in the waste stream of gold processing plants using cyanidation. Factorial experimentation has been conducted to create models of copper recovery, cyanide recovery, acid addition, and oxidation/reduction potential during SART. Economic analysis of the resultant models showed that SART is best operated with a sulphide-to-copper molar ratio of approximately 0.56, pH of 4, and a minimized cyanide-to-copper molar ratio. The experiments also showed th0at residence time can have drastic impacts on SART performance.

Jan 1, 2013

By M. Brennan, A. Majumder

"The mineral processing research community has devoted enormous efforts to the modelling of mineral separators over the last 50 years. While many efforts have been made to use only fundamental physics as a basis for the models, fluid flow patterns in separators are not simple while the motion of particle swarms through fluids is extremely complex.One of the simplest separators is the sluice, in which separation takes place in a flowing film a few millimetres thick. The particles are suspended by turbulent eddies and motion relative to the fluid takes place in so-called hindered settling mode.In an effort to test the extent to which fundamental fluid mechanics can provide a prediction of particle separation, a study on a simple parallel-sided sluice has been carried out using glass beads at various particle concentrations and flow rates.The actual particle separation taking place was compared to predictions made by first describing the fluid flow by a modified ‘law of the wall’ model.Particle concentration distributions were described using Hunt’s sediment transport model, assuming the particle eddy diffusion coefficient to be the same as that for the water. Settling velocities were calculated using either the Richardson and Zaki or Brauer and Thiele models. The latter takes into account particle size and density distributions and solids volumetric concentration.The resulting predictions of particle separation are remarkably good, even though the model does not model the local settling velocity in the slurry."

Jan 1, 2003

By Martin McKinnon, Guy Reed, Russell Frith

"It is arguable that the development of reinforcing roof bolting systems has largely stagnated in recent times, primarily due to the prevailing industry view that few, if any, further improvements can be made to what currently exists. However, this paper contends that reinforcing roof bolting systems can be further refined by considering both the specific manner by which horizontally bedded roof strata loses its natural self-supporting ability and the specific means by which reinforcing roof bolts act to promote or retain this natural self-supporting ability. The Australian coal industry insists on minimising bolt-hole diameter to maximise load transfer and on targeting full-encapsulation by any means necessary. This has led to a significant, albeit unintended, consequence in terms of overall roof bolting effectiveness, namely increased resin pressures during bolt installation and the associated potential for opening bedding planes that may have, otherwise, remained closed during the bolt installation process. Given that the natural self-supporting ability of roof strata is strongly linked to whether bedding planes are open or closed, logically, minimising resin pressures should be a significant benefit. This paper focuses primarily on three key issues that relate directly to the function of the roof bolting system itself: (i) the importance of proper resin mixing in the context of maximising load transfer strength and stiffness, (ii) the importance of minimising resin pressures developed during bolt installation, and (iii) the importance of maximising the effectiveness of the available bolt pre-tension. All mine operators should be invested in improving the individual effectiveness of each installed roof bolt, even by relatively small incremental amounts, so this is an important topic for discussion within the mining community."

Jan 1, 2017

By Janusz S. Laskowski

The flotation-related properties of hexanol derivatives and mono-alkyl ethers of propylene oxide, which include many important flotation frothers (e.g. MIBC, DF-200, DF-250, DF-1012, etc.) have been studied. The obtained results show that the DFI (Dynamic Foamability Index) - CCC (Critical Coalescence Concentration) plot can be used to classify flotation frothers. The frothers characterized by low CCC and high DFI values have properties of strong flotation frothers, while those with high CCC and low DFI values are more selective. The proposed frother classification system, based on simple CCC and DFI measurements, provides, for the first time, a solid ground-work for characterization of the flotation frothers.

Jan 1, 2003

By Lee W. Saperstein

The SME Research Council assists SME and its constituencies in establishing research directions that will benefit the mining industry and its professions. It also provides information about these directions to its membership, to government and to related industrial societies. The 1995 Research Forum, organized and chaired by George Luxbacher, was the second in a series of meetings organized to develop these directions. A copy of the full proceedings is available from SME for $12 plus postage and handling. The first research forum (Saperstein, L., 1993, "Technology for the Future, MINING ENGINEERING, Vol. 45, No 11, November, pp. 1382-85) invited mining industry representatives to discuss the unsolved technical problems that were keeping the industry from greater economic and environmental efficiency. The second forum asked academic researchers to discuss the same general topics from their perspective. It came as no surprise that, in general, the two sets of presenters tackled the same problems. There was no surprise when the academics spoke of the need for fundamental long-term research. What may have been surprising was the number of university people who spoke for near-term research that leads to measurable economic returns or savings. The closure of the US Bureau of Mines (USBM) has changed the objectives and attitudes of the SME Research Council. From being a point of liaison between SME and USBM - a conduit of items from each party to the other the council is now much more on its own. This isolation presents opportunities and hazards. The opportunities are exciting because the council could be the focus for mineral industry research policy if it were properly structured. The hazard is obvious - if there is no bureau, it could be argued, why maintain the council? Many people believe that SME should take the first course and become the beacon for research policy. More than ever, money is being spent on minerals industry research by the federal and state governments - particularly at the mineral-oriented land-grant universities - by industry and by consortia among these groups. SME could be at the hub of these programs. There is a general concern that industry is less able to maintain an economic edge by means of geologic discovery. According to Titley, there will be fewer major, new world-class discoveries except, possibly, at the continental and tectonic-plate margins. Consequently, economic advantage will go to those companies and nations that stay ahead technologically. Given the inevitable diffusion of technology, it can be concluded that technology development, underpinned by research, must be continuous to maintain profits. This is a change from earlier years when change would occur in relatively rare major steps that were interspersed with extended periods of technological equilibrium. Over the fiscal years 1994 to 1997, there has been a 24% cut in research spending by the Department of the Interior (figures from the American Association for the Advancement of Science). This is the largest budgeted percentage cut in research funding of any federal department. Even so, there is still a substantial amount of federal research funding expended in the mineral and extractive-energy industries. The US Geological Survey, Environmental Protection Agency, Departments of Defense and Energy and others expend substantial funds on minerals industry research. Industry - producers and manufacturers - is also spending large sums on research and research-like activities. This activity argues that there is a role for SME's Research Council. Providing focus Consortia. The closure of USBM has resulted in the migration of expertise to consulting firms and to other entreprenrutisl research entities. Many of these groups are creating ad hoc consortia among themselves, nearby universities and industrial partners. The Research Council is well placed to provide an open forum for these con¬sortia. Presentations of research results, as went on in the annual meetings of the Generic Mineral Technology Centers, can help to establish an. archive of results and an avoidance of duplication of research. A continuing sense of research directions can evolve. National Science Foundation. No discussion of consortia would be complete without mention. of the National Science Foundation's (NSF) programs for Industry/University Cooperative Research Centers (IUCRC) and Grant Opportunities for Academic Liaison with Industry (GOALI). NSF is aware of the gap in federal support of science and technology caused by USBM's closure.

Jan 1, 1997

By Luben Savov

This paper presents recent research works on the removal of the tramp elements Cu, Sn, Zn and Pb from steel. The evaporation of Cu and Sn in iron-based melts treated at reduced pressure of the gas phase was studied in a vacuum induction melting furnace. The effect of chamber pressure, temperature and melt composition was investigated. Since the main source of contamination of steel with Sn and Zn is the recycling of tinplate and zinc coated steel, respectively, possibilities for the removal of meta1ic coatings in a scrap pre-treatment stage were studied, too. Tin was removed in the temperature range 400-5S0°C by treatment with reactive gases featuring high sulphur potential. Zinc can be removed by evaporation or by a combination of thermal and mechanical treatment. The paper discusses the thermodynamics of Pb in carbon-saturated iron melts, too.

Jan 1, 2001

By N. Mohan, A. K. Biswas, V. Y. Sampat Kumar

At low sodium-oleate concentration, calcite flotation is substantially improved by the use of CO2 instead of air. Electrophoretic mobility measurements indicate that carbonation results in the accumulation o f positive charge on the calcite particles. This heightens adsorption of oleate anion, an effect confirmed by tracer-technique measurements. Fundamental insight is obtained as to how CO2 serves better as an activator than some mineral and organic acids, how oxalic acid acts as a depressor, and why the influence of Ca++ ions, liberated during carbonation, on flotation behavior of calcite is insignificant and sometimes adverse.

Jan 1, 1972

By Masahiro Shimura, Yoshiki Takahama, Toshiyuki Shiraishi, Daisuke Kasai

When advanced high strength steel (AHSS) is rolled at a high reduction ratio, the forward slip ratio in cold rolling tends to be lower than that of the other softer strips such as low-carbon steels, and the work roll sometimes skids the strip. To identify why forward slip ratio of AHSS at a high reduction ratio becomes smaller than that of low-carbon steel, the relationship between the reduction ratio and forward slip ratio was investigated by a rolling experiment. For this trial, a 4Hi laboratory cold mill was used. AHSS and low-carbon steel coils were rolled by two different rolls that were set to 0.3 and 0.6 μmRa to create two types of friction conditions. Furthermore, the rolling conditions were numerically analyzed to determine the influence of friction coefficient and flow stress on the relationship between forward slip ratio and reduction ratio. The experimental investigation and numerical analysis revealed that the forward slip ratio reduced with increasing rolling reduction ratio in a low friction state; contrarily, it increased with increasing rolling reduction ratio in a high friction state. This feature was clearly visible when harder materials were rolled.

Oct 1, 2019

The world is getting flatter through internet, mobile phone technology, relatively low cost travel, massive outsourcing of manufacturing to China and the transfer of company backroom operations to India. In the iron and steel industry, however, things will remain relatively the same with slow gradual improvements in technology; only the geographic location of plants may change over time. Or will it? The blast furnace smelting process has remained largely unchanged since 1828 when James Neilson came up with the idea of preheated air being delivered to the tuyeres. Likewise, oxygen steelmaking that takes molten iron from such blast furnaces has remained conceptually unchanged since Sir Henry Bessemer invented an air-based system in 1856. These two processes are the core of integrated steel mills that we know today. Typically such mills consist of coke ovens, sinter plant, blast furnace, oxygen steelmaking, continuous caster, rolling mills and metal coating lines. In the intervening 150 years the only real disruptive technology to the integrated steel mill has been the minimill. Based on the use of the electric arc furnace (EAF), in conjunction with a continuous caster and rolling mill, the term minimill is used because steel products are produced at down to one-tenth the scale required for economic operation of an integrated mill, with the EAF producing molten steel using largely scrap steel as its feed, as against transforming coal to coke (coke ovens), iron ore, coke and limestone into molten iron (blast furnace) and molten iron to steel (oxygen steelmaking). There are, however, a number of technologies in development that may cause a paradigm shift in the way steel products are produced and perhaps push the evolution of the minimill as a disruptive technology. Two examples are direct iron smelting, where iron is produced in a matter of seconds by injection of ironmaking feed materials into a molten bath, and thin strip casting, where molten steel is cast into 2 mm strip or less, in similar time. Both have Australian connections. A leading iron smelting technology is the HIsmelt« process, which has its first commercial application at Kwinana, Western Australia, where a joint venture of international parties, consisting of Rio Tinto and the Nucor, Mitsubishi and Shougang corporations, are in the stage of ramping up commercial production. The leading strip casting technology is the Castrip« process that arose from development work done by then BHP Steel, with IHI of Japan, at Port Kembla, New South Wales in the 1990s. Nucor followed this work up, building the first commercial plant for the technology at its Crawfordsville site in Indiana in 2001 and has recently announced an intention to build a second plant in the USA. While both technologies are only into the early stages of commercialisation they are likely to change the face of iron and steelmaking as we know it over the next 20 years. This paper elaborates on the technology of the two processes, why they could change the face of the iron and steel industry forever, what might drive the rapid change and what the changes may look like.

Jan 1, 2006

By Donald A. Bruce

Pin Piles are small diameter, bored, cast-in-place piles used to underpin structures. They were first employed over 40 years ago in Italy, and have been used in the U.S. since the late 1970's. However, it is only in the last few years that their full potential in terms of load holding capacity has been exploited: whereas 100 kip working loads typified former practice, ultimate loads approaching 700 kips have recently been recorded for Pin Piles founded in sand. In order to better understand the actual performance of these piles, fundamental research has been conducted by a consortium of industry and academia. This paper describes the advances made in the laboratory and full scale field testing programs. In particular, the extensive field tests have been conducted in a variety of materials in which different pile configurations have been cyclically tested to failure. By using this test method, the elastic performance of the piles has been examined and so the progressive interfacial debonding phenomenon has been studied. This has led to the development of the Elastic Ratio concept which is proving extremely useful in analyzing and predicting Pin Pile performance. Data are provided from the full scale Test Pile Programs conducted at Mobile, AL and Port Vancouver, WA. Given that Pin Piles are usually installed in areas of low headroom or restricted access, and through difficult, occasionally contaminated soils, the paper also describes key aspects of construction.

Jan 1, 1993

By M Jones

The past 100 years the mining industry can be characterised by a focus on increasing financial returns often to the detriment of social, human, manufactured and environmental capitals. Despite the sustainable development principles promoted by the International Council on Mining and Metals (ICMM), the Equator Principles and the African Mining Vision, which should have enhanced project promoters’ ‘licence to operate’ within a host community or nation, the industry has often failed to integrate proven innovations and best practices that enhance sustainability outcomes for mineral resource projects. This failure has led to delays, the abandonment of projects, with value destroyed for promoters, governments, host community and investors.The paper will outline the application of proven innovations, Enterprise Optimisation (EO), and Sustainable Operations (SUSOP®), during the pre-feasibility phase of a project. By determining the value of each capital before and after the application of proven innovations, the presentation will outline how and where value can be created across all five capitals over the life of a project or operation.The paper will demonstrate how the application of proven innovations significantly transforms the value-proposition of a mineral resource project or operation by generating additional value across all of the five capitals, reducing project risk, thus generating value for all stakeholders.CITATION:Jones, M, 2015. Fundamentally transforming the economic and sustainability signature of mining assets, in Proceedings Third International Future Mining Conference, pp 169–180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Rainer Schmid-Fetzer

"Isothermal solidification can be used to form strong bonds at low temperature which remain solid at much higher temperatures. The exploitation of this principally known technique for new high temperature processing steps and applications in electronic assemblies is the aim of this study. Three basically different variants of this bonding process are given. A comprehensive metallurgical screening is performed and the feasibility of binary material systems is given on a quantitative scale. Very attractive systems are spotted that have never been studied before. Detailed examples for the realization of bonding with complex ternary and multilayer systems are given. A highly innovative example is the chip stack or wafer to wafer bonding of unmetallized Si or SiC at 250°C. The proposed bond remains stable above the melting point of Si and enables entirely new semiconductor manufacturing steps. An improved die bonding process was proposed and verified experimentally.1. IntroductionIsothermal solidification can be applied to form strong bonds at relatively low temperature which remain solid at higher temperatures. The general principle of this type of joining processes is illustrated in Fig. 1. An interlayer of a low melting component, Lo, is provided as a foil or a thin film coating between the high melting joint components, Hi. The assembly is heated under moderate pressure to the bonding temperature, T 8 , and a liquid filler forms, either because the melting point of Lo is exceeded or due to a eutectic reaction between Lo and Hi. This molten filler initiates a rapid interdiffusion or reaction diffusion between Lo and Hi and the subsequent approach to an equilibrium state results in isothermal solidification. The solid phases formed at T 8 in the joint region exhibit a remelt temperature above T8 •"

Jan 1, 1996

By S. M. Carpenter

In an ever increasing ?carbon? society; management and growth will be measured by one?s carbon footprint (or output). Industries, especially mining, are under an ever increasing scrutiny of carbon, water and environmental mandates. These mandates are measured by the emissions caused by the combustion of fossil fuels. The fundamental building-block for any business, strategic or management decision must be based on an understanding of one?s ?footprint?. The scrutiny is most stringent for the commodities producers, power producers & fuel suppliers in the energy market. An overview of currently acceptable standards, application of those standards and nuances experienced in collecting the data necessary to analyze and complete a company?s carbon footprint will be presented. A lack of regulation, the fear and expectation of new and ever constraining rules, regulation and a change in the federal administration is a recipe for uncertainty in the marketplace.

Jan 1, 2010

The cyclone, or centrifugal separator, ,is firmly established in industry as a low cost separator of solids from gases.While it will also separate fluids of different densities, and solids from liquids, its main use is to remove relatively fine dusts from gases whose pr~erties are generally not greatly different from those of air. This latter phase of operation is the one that will be dealt with here.The duty of such a cyclone separating system is to take in a supply of dusty gas and separate it into its components of dust and clean gas as perfectly as possible for the least consumption of pressure head. Any separation at all causes pressure loss and, in general, the greater the separation, the greater the pressure drop needed to effect it. The percentage of dust in suspension which is separated from the gas-dust mixture is commonly called the collection or separation efficiency. Overall or "true" efficiency must take pressure drop into account and may be considered as proportional to the ratio of the percentage of dust collected to the resultant pressure drop. For any cyclone It will vary with different dusts.Many commercial adaptions of the simple cyclone are made solely on the basis of pressure drop improvement, without taking into account the effect on separation efficiency, probably because the latter is so difficult to assess correctly. It appears unfortunate but true that the majority of such adaptions and patent gadgets fitted to cyclones which decrease pressure drop, do have an adverse effect on separation. In other' words, the true efficiency is seldom increased but often diminished.Without a knowledge of what actually goes on inside a cyclone, it is impossible fully to appreciate the real effect of a modification. For instance, it is on record that a cyclone...

Jan 1, 1949

The great problem at Port Pirie and many other lead smelters has always been to keep the lead content of the slags down to a low level. This has been done in the past largely by empirical methods, the lead content varying from less than 1 per cent to over 4 per cent, the more usual figure being something under 2 per cent. Subsidiary to this, but of major importance in the future, was the extraction of the considerable quantities of zinc in the slag. At this stage little was known about the constitution of the slags apartfrom their chemical composition. Some early work on slag constitution was carried out in the B.H.A.S. Research Laboratories between 1919 and 1921, but except for a microscopic examination of a few thin sections the greater part of this investigation wasdevoted to the recovery of the zinc content of the slag by leaching methods.In 1949, therefore, it was decided to initiate a programme of fundamental research into the constitution and properties of the lead blast furnace slags. The information thus gained would give a clearer picture of reactions taking place in the slag, both in the blast furnace and during dezincing.There was also the hope that these results would lead to improved industrial techniques resulting in smaller lead losses, and, taking the long-term view, to efficient methods of producing zinc from the slags.A series of investigations was therefore begun at various centres over a period of time. These were:1. A mineralogical examination of the slags by Dr. A. B. Edwards of the Mineragraphic Section, C.S.I.R.O.2. A study of the thermodynamics of various slag com...

Jan 1, 1956

By da Silva C A, Tenorio J. A S, de Assis R M, de Oliveira J R

For Fe-Mn alloy production, two reactions are responsible for this process: the MnO reduction in the slag and the carbon dissolution in the bath. The smelting-reduction process has been studied as alternative route to be used to produce alloy so as steel. This technical paper presents some initial studies to be used to determine the main ways that one can have for the mechanisms for this reaction. The limited factors like mass transport or chemical reaction were analysed. The Mn content in the bath were varied and it was concluded that by increasing the former, dissolution of Mn into the bath was increased, so as a reduction of MnO in the slag. For carbon dissolution, it was used a experiment with a stationary bar, this one was added into the bath, after ten minutes probes were catched, by temperature 1600¦C, for the dissolution of MnO, one graphite crucible was employed, after 45 min the slag and alloy were analysed. After the experimental part, some curves were plotted against time, based on these graphics, and kinetic analysis was made.

Jan 1, 1999

By John S. Brock

INTRODUCTION The Oxford Dictionary says that the word "promoter" has usually been used in an opprobrious sense since at least 1876. This popular image of mining promoters is of cigar-chomping shysters and Brooklyn-Bridge vendors, improving their standard of living with the aid of funds raised through the sale of stock to little old ladies. It is unfortunate that mining promoters are considered crooks until they can prove their integrity and honesty by finding a mine. A common rule of thumb states that for every 1,000 prospects, 100 come to be drilled, and one becomes a mine. However, it is also a statistic that there have been mining promotions, where money raised has gone elsewhere than into the ground; Junior exploration companies can be handy vehicles for unscrupulous financial activity. One must remember though that every stock exchange has had its share of sound mining promotions that, because of the one in 1,000 odds, have failed for legitimate reasons. The promoter must be able to rationalize the worth of a mineral discovery which, on an industry- average basis, probably cost more to find than the discounted value of its net return, which return is not an assured percentage of invested capital, and furthermore, is ultimately from a wasting asset. So, it is easy to understand why the promoter must constantly justify the credibility of his operation to his grubstakers during the course of the "five phases of exploration," those being (1) euphoria, (2) disillusionment, (3) search for the guilty, (4) punishment for the innocent, and (5) distinction for the uninvolved. The promoter with the exploration organization that does not have the benefit of positive cash flow, by definition for the sake of this article, works for a promotional outfit, a Junior Company, that must raise its exploration budget from a variety of sources. Promotion, as discussed here, will not entirely refer to the formation and operation of a joint- stock company but rather to the overall methods of raising risk capital for mineral exploration ventures from outside sources. THE NECESSITY OF PROMOTION In Canada, the publicly financed Junior Company has had an enviable record of mine-finding success. In the Province of British Columbia alone, the discovery of fifteen out of twenty-four mines has been as a result of the activity of the Junior Company (B. C. & Yukon Chamber of Mines, 1977). In the Province of Ontario, one research study indicated that between 1951 and 1974 the 'Juniors' spent only 28 percent of the total exploration funds but were responsible for 62 percent of all economic discoveries (Freyman, 1978). The reasons for the success of the Juniors are tied to a variety of factors, the main one being personal initiative based on incentive. In other words, the principals, or their employees have 'a piece of the action.' The smaller companies can operate faster and more efficiently than their larger counterparts. The Junior Company is also destined to take some bigger risks, the 'long shots,' many of which efforts by virtue of the Junior's perseverance coupled with a touch of 'ore is where you find it' philosophy, result in major discoveries. The individuals, syndicates, private and publicly financed Junior Companies, because of high costs of exploration and development, cannot hope to finance most mineral prospects all the way to production. Exceptions do exist, those being the lower capital cost, small, high-grade deposits. Private investors and publicly financed Junior companies, therefore, can usually afford to finance most exploration through the initial drill-testing stage. The major resource company will enter a mining deal with a Junior Company usually by way of option or joint venture agreement, and will finance to production to earn an equity in the prospect or the Junior Company or both. The conventional lending institutions, banks and government agencies, will usually only participate through loaning a portion of capital

Jan 1, 1985

By H. J. Oterdoom

SMS Group (SMSG) has always been concerned about safety aspects of electric smelter plants for the ferro-alloy and non-ferrous industry. The awareness for safety increased significantly over the past decades and also SMSG contributed with its design features to a safer operation. Today, safety aspects are not only part of the smelter design but also of the overall plant layout. Explosions in electric smelters are rare, but have a huge impact on peoples’ lives, on equipment and on production. For this reason, SMSG wanted to have a better overview of explosions within the smelting industry in order to see if useful statistics could be extracted. Generally, there is a lack of statistics regarding explosions in the electric smelting industry, and not enough information is collected or published. A significant portion of the explosions seems to be water related. Many companies, both operating and engineering, are trying to handle the risks of water, and apply methods to detect water leakages. Installing such a system is a management decision and management has then to make sure the system is properly implemented. The disadvantages and limitations of these systems should be carefully considered and communicated to operators and authorities.

Jan 1, 2015