Search Documents

By Sunil Koppalkar, Guillaume Noel, Ahmed Bouajila, Makni Sami, Claude Gagnon

"Gold gravity recovery circuits utilizing enhanced gravity separators have become an integral part of many of the modern gold processing plants. Thus, efforts to improve the operating efficiency have been a topic of interest for metallurgists for many years. As part of this endeavour, a methodology to estimate the portion of gold in the ore that could be recovered by gravity separation (gravity recoverable gold or GRG) was developed at McGill University. It has been reported in the literature that the gold content estimated with this methodology is the theoretical maximum that is available for gravity recovery that could only be approached but never achieved. A comparison of GRG recovery obtained in the laboratory with the actual recovery in the plant shows that plants recover between one-third to two-thirds of the value predicted by the laboratory test.Research conducted at COREM shows that particle shape transformation during grinding is a major cause of the discrepancy (even though the bleed percent processed, the quality of cyclone classification and the operating conditions of the gravity separator also contribute to the difference). To analyze the gold particle shapes and their deportment, samples were collected from different streams of a grinding-gravity circuit in a gold plant and compared to a concentrate sample from the standard GRG test. A particle characterization methodology based on gold morphology was developed. GRG mapping in a conventional grinding-gravity circuit and the transformation of GRG into non-GRG, as mainly explained by gold particle reshaping, will be discussed. The knowledge gained from the shape analysis will be used to develop shape distributions and partition curves for the classification of shapes.INTRODUCTIONGravity concentration using centrifugal concentrators has gained increasing popularity since the invention of the enhanced gravity concentrators in the nineteen eighties. Among these, the semicontinuous centrifugal gravity concentrators are most commonly used for recovering gold and platinum group minerals (PGM) from grinding circuit streams. The benefits of gold gravity recovery are now well understood and the acceptance by the mining industry is overwhelming. The occurrence of reasonable amounts of gravity recoverable gold (GRG) in an ore prompts gold mills to install gravity circuits. Thus, the increased use of gravity concentration has necessitated a better understanding of the behavior of gold in grinding circuits and of the factors affecting the performance of the gravity concentrator (Laplante et al., 1995). Due to its high density (19.3 g/cm3 when pure) and malleability properties, gold tends to accumulate in circulating streams making it attractive for gravity recovery. The gravity recovery units are typically installed on a bleed stream of the cyclone underflow, mill discharge or cyclone feed."

Jan 1, 2011

By U. A. Peuker, T. Mütze, F. Shayo, A. Wikedzi

"Buzwagi Gold Mine (BGM) is operated by Acacia Mining and located in the Lake Victoria Goldfields of central Tanzania. The mine treats a sulphide copper-gold ore to produce gold in form of doré bars and a concentrate containing gold, copper and silver. The BGM comminution circuit includes a primary crushing stage with a gyratory crusher and two grinding circuits using a Semi-Autogenous Grinding (SAG) mill and a ball mill. Currently, the grinding circuits are inefficient in achieving the aspired product fineness of xP,80 = 125 µm even at low to normal throughputs (450-600 t/h). An optimization study of the circuit performance was conducted to improve product fineness through circuit surveys, experimental lab work and simulations. The analysis of survey data revealed inefficient grinding operation characterized by ball mill product (xP,80 > 400 µm) coarser than designed and higher hydrocyclone cut sizes (xT > 200 µm), too. In MODSIM several options were simulated such as reduction of vortex finder and apex diameters, reduction of SAG screen aperture, and modification of cyclone feed density. An improvement of product fineness could be achieved by simulation of the cumulative changes but it was also concluded that the current equipment cannot achieve the target. Further simulations showed that a second ball mill might help to achieve the desired fineness as well as an increase of grinding throughput by up to 26 %. INTRODUCTION Simulation of comminution, particularly grinding and classification, has received great attention for many years, due to the fact that the unit operation is by far the most important both in terms of energy consumption as well as overall plant performance (King, 2001; Wills et al., 2006). The use of simulation is advantageous due to low cost as well as its ability to consider many variables simultaneously. Moreover, there are some benefits for optimizing grinding operations by simulation like decreased unit operating costs, increased capacity, and improved performance of downstream processes due to improved feed size distribution. This paper presents an optimization study for the grinding efficiency at Buzwagi Gold Mine. This was achieved through three full scale circuit surveys, lab work and simulations with MODSIM."

Jan 1, 2018

In this paper High Pressure Grinding Rolls(HPGR) was utilized to pretreat CVRD southern specular hematite for enhancing the pelletization of the refractory hematite. The process parameters of HPGR, balling and firing were optimized, and the mechanism of HPGR was demonstrated by determining the surface activity by means of Blaine specific surface area tester, laser size analysis, scanning electron microscopy (SEM),X-ray diffraction (XRD), micro calorimeter and pelletability index. It is shown that the pelletization of the refractory hematite was greatly improved. The drop strength of green balls increases from 3.4 times to 13.6 times from 0.5m height while the bentonite dosage decreases from 2.2% to 1.3%.The compressive strength of roasted pellets also reaches 2500N/pellet. The mechanism of the pretreatment of CVRD southern specular hematite concentrates by HPGR is revealed that the surface activity is improved by an increases in specific surface area and the amount of micron size fractions, and higher lattice deformation and defects due to the fractures occurring inside particles during static pressure comminution, resulting in more wetting enthalpy, higher pelletability index and good property of roasting.

Jan 1, 2014

By T Purvis, Z Liu

Ernest Henry mine (EHM) is an underground sublevel caving mine located in north-west Queensland with a production rate of 6.4 Mt/a. The mine has sublevels spaced with a 25 m vertical interval. The production process on each level starts with the drilling and firing of a blind uphole rise to start the slot extraction. These rises are fired as a single shot and routinely need to achieve a design height of 22 m to 30 m depending on the local mine geometry. If the rise fails to perform as designed then the production phase of the level is delayed with significant rework required to remedy the situation.This paper describes the process that the EHM team has followed to improve the first time performance of each rise. The improvement process commenced with a review of results from previous rises and resulted in the identification of a number of improvement opportunities. A revised holistic approach was established for the process, which included involvement from operators and engineers. Through continued measurement and review of rise performance, inputs to the process were improved to a point where reliable results can now be expected. The successful performance of subsequent rises has been verified through a comprehensive quality assurance quality control (QA/QC) program. Before quality control processes were implemented, the success rate of blind uphole rises was only 11 per cent (one out of nine rises) at EHM. In comparison, the success rates have been vastly improved to 25 per cent (one out of four) and 75 per cent (three out of four) respectively following two stages of improvements. This paper concludes with the ‘current’ series of best practices used at EHM and recommendations.CITATION:Purvis, T and Liu, Z, 2017. Improving the performance of blind uphole rises at Ernest Henry Mine – a case study, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 335–340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By J. H. Archibald

"IntroductionShot-saws are used for sawing rock throughout the dimension stone industry especially in granite quarry mills. Shot-saws, as currently designed, have an inherent wear problem which leads to slow cutting rates and repetitive blade changes which consumes much time. Because the saw blades are made from steel the abrasive shot used with them is limited to a certain hardness which effects the over-all efficiency of the sawing operation. Suggestions are made toward optimization of blade design and the sawing process. Blade DesignA common steel blade design is shown in Figure I. Note the perforations in the blade. These perforations or holes in the blade serve two or three purposes. The most obvious reason is to allow the abrasive shot a pocket in which to collect at the bottom of the blade, so that it can be distributed from these pockets into the cutting zone underneath the blade. The abrasive is fed to the saw in a slurry and usually comes in from the top. The blade must then cut a kerf wider than itself in order that the abrasive grains have a path leading from the top of the blade, down along its sides, and finally reaching the pockets and cutting zones. This circuitous path followed by the abrasive leads to side wear on the blades and high friction which can lead to blade buckling in severe cases. However, the fluidized path of the abrasives down the sides of the blade serves another purpose which is a positive gain if conditions are properly controlled. The abrasive slurry interacts with the perforations of the blade, the blade itself and the rock. This gap and the perforations in the blade, which are fluid filled, are sites of constant shearing motion. Eddy currents form in these gaps and pockets which tend to stabilize the blade by setting up balanced hydrodynamic forces which otherwise might not form in a non-perforated blade. A stable blade produces a more uniform cut in the rock. The third and final reason for the perforations are to allow the blade to wear in such a fashion that new pockets are always being formed and, consequently, new cutting surfaces between these pockets are also formed."

Jan 1, 1993

By Ronald L. Wiegel

In a mineral processing plant there are a number of routine decisions which are based at least in part on the plant's metallurgical performance. Among these are those related to: 1) equipment functioning properly 2) suitable operating conditions 3) reagents achieving desired results 4} determining operating response to changes in ore 5) defining circuits offering potential for improvement A step beyond the routine, are the periodic management evaluations of operating supervision and technical assistance, which are based largely on profit -a direct function of are availability, metallurgical performance and operating costs. The "yardstick", excuse me -"meterstick", by which performance is best measured is the plant metallurgical balance, which tells not only what was produced but how it was produced. Since this metallurgical balance is directly related to both plant profits and individual rewards, it is only reasonable to make that "meterstick" as precise as humanly possible.

Jan 1, 1978

By I. M. S. Moraes

Caraiba Metais has a plant for the purification and the cristallization of the crude nickel sulfate removed from its copper electrolyte purification system. In November 1994, an interdepartmental group was formed to study the Q.F.D. method, through its application on the improvement of the quality of the nickel sulphate hexahydrate. The team, formed with representatives of the following areas : production, technology, marketing, sales, maintenance, laboratory and TQC office, had also the task of checking the applicability of the method to other products of the comp any. This paper describes the main steps such as the survey of customer's demands, the preparation o1 the quality matrix, stablishing the planned quality matrix, the planned and the designed quality, and the consequent identification of the engineering bottlenecks. It is also shown how these bottllenecks were studied and solved. The application of the method allowed the team to identify means of increasing the production capacity by 40%, to improve the intrinsic quality of the product (including packaging), and to increase the reliability of the process.

Jan 1, 1997

By G. S. Maré

Tin plating operations are of a complex nature due to the many operational variables that need to be controlled in order to create a product of required quality. The work in this report lays the basics for the control of a halogen plating operation based on the DuPont tinplating set-up with regard to the chemical make-up of the plating solution, as well as operational variables such as temperature and current density. To evaluate these aspects of the process, a rotating cathode Hull-cell set-up was used. This allowed for a laboratory scale plating arrangement that simulates industry closely with regard to chemical and hydro-dynamic considerations. Typical industry accepted standards were obtained for the values of operational variables and a ?baseline? test was conducted employing these standards. All subsequent tests conducted were benchmarked against this baseline result. A large suite of results was obtained in which it was found that changes could be made to the industry accepted norm which would improve on the stability of the operation and therefore the quality of the final tin-plated product. Examples of these results are: an increase in stannous tin concentration, an increase in sodium chloride concentration and a slightly elevated plating temperature. In addition, conditions were found that must be avoided to prevent instability and poor product quality.

Jan 1, 2010

By G J. Harbort, Z Pokra

It has been observed in several Jameson cell installations where the source for flotation feed is deslime screens, that the recovery of coal particles greater than 0.5 m is not as great as that of finer material. Consequently, a research project was undertaken at a CHPP in the Bowen Basin, Queensland, to assess the possibility of increasing the recovery of coarser particles (+0.5 mm) within the downcomer of the Jameson Cell. The effect of decreasing turbulence and agitation in a commercial-scale downcomer was investigated to assess the effect on the recovery of both coarse and fine coal particles. This paper details the findings of the testwork, summarising the results relating to differences in the operating parameters within the downcomer.

Jan 1, 2005

By H. Möhle

Premier Mine is a large underground diamond mine, situated at Cullinan in the Gauteng Province of South Africa. The mine hoists over 3 millions tons of diamond bearing kimberlite per year, from a modern, mechanized panel retreat block cave mining operation. Troughs sited at the base of the cave are developed into the overlying caved ore, allowing loading access to the ore through draw points. Trough opening is therefore a vital aspect of the mining operation. Most of the production is dependent on fast, reliable and safe trough opening. Successful trough openings are achieved under difficult mining conditions due to restricted void, long up-holes and the inherent properties of kimberlite?soft, elastic rock with a high swell factor. Early in 1998, Premier Mine undertook a joint development project (with an electronic initiation system supplier) to determine whether the use of a fully programmable electronic detonator system would enhance the mining cycle in the trough opening process. Blasting commenced in February 1998, initially with blasts of a similar size and duration to those that had been previously blasted with shock-tube systems, to confirm the operational capabilities of the blasting system. The accuracy, reliability and flexibility of the electronic delay detonators (EDDs) minimized associated risks for re-engineering of the trough opening process. Further, as blast timing was optimized, larger blasts were successfully initiated. To date over 20 troughs have been opened successfully with the use of EDDs. Not only did it take less time to open troughs, but also drilling and blasting operations have been optimized, as well as an overall improvement in safety. This paper details the benefits that EDDs have delivered to Premier Mine in this area. The logic followed is: ?Review of the original trough opening practices ?Re-engineering of the trough opening process ?Implementation of EDDs ?Evaluation of improvements and conclusions.

Jan 1, 2000

By Kara A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature, and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68 °C and 141 °C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large scale experimental configuration, the installation specifications of the fire suppression system, and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature, and limited water application on the suppression system performance.

Jan 1, 2010

By A. M. Salomon de Friedberg

"With respect to impurities, HBM&S' copper smelter, located in Flin Ron, Manitoba, is in an unusual position. In addition to the usual concerns, the fact that copper and zinc production at Flin Ron is closely integrated results in the unique situation where feed to the copper smelter typically contains 7% to 8% zinc. This paper discusses the ramifications to copper smelter operations resulting from the marriage of HBM&S' metallurgical plants. Distributions of impurities (specifically Zn, Pb, Ni, As, Bi, Sb, and Cd) are presented and operating practices designed to reduce the impact of impurities on anode copper quality are detailed.IntroductionHudson Bay Mining & Smelting Co. Ltd. (HBM&s), has been operating its metallurgical complex located in Flin Flon, Manitoba, since 1930. The smelter and zinc plant were originally separate entities with respect to production. The smelting operation consisted of traditional multiple-hearth roasters, a reverberatory furnace and Peirce-Smith converters. The zinc plant also utilized multiple hearth roasters and then followed with sulphuric acid leaching, purification and electrowinning. The zinc plant also recovered cadmium from a separate purification/electrowinning circuit.The two plants operated essentially independently of each other until rising zinc levels in the copper concentrate and large stockpiles of zinc-rich leach residues prompted the construction of the fuming plant in 1949. The smelter used pulverized coal to reduce zinc oxide present in the reverb slag and then captured the resulting zinc bearing fume in the fuming plant baghouse. The fume was sent to a separate ""oxide roaster"" in the zinc plant where it was first roasted to remove halogens and then leached to recover the contained zinc. This oxide fume became a major source of feed to the zinc plant accounting for roughly one quarter of the total zinc production. Furthermore, through the smelter's treatment of sulphide leach residue, both copper and zinc recoveries were improved for the over-all complex."

Jan 1, 1993

By A. M. Salomon de Friedberg

With respect to impurities, HBM&S' copper smelter, located in Flin Flon, Manitoba, is in an unusual position. In addition to the usual concerns, the fact that copper and zinc production at Flin Flon is closely integrated results in the unique situation where feed to the copper smelter typically contains 7% to 8% zinc. This paper discusses the ramifications to copper smelter operations resulting from the marriage of HBM&S' metallurgical plants. Distributions of impurities (specifically Zn, Pb, Ni, As, Bi, Sb, and Cd) are presented and operating practices designed to reduce the impact of impurities on anode copper quality are detailed.

Jun 1, 1993

By S. Mondon

Hibi Smelter which is a Copper Smelter lining a blast furnace, produces 2,700 metric tons of anode copper per month. Generally, in a copper refinery, arsenic and antimony are considerably troublesome impurities. With regard to the elimination of antimony, Hibi Smelter has two handicaps described as follows. (1) Smelting under the slightly oxidizing atmosphere in the blast furnace. (2) Recycling the converter slag to the blast furnace after cooling. Therefore antimony and arsenic, mainly antimony, elimination tests, in which the alkaline flux was injected through the two tuyeres in the blowing stage, were carried out in the rotary anode furnace. Antimony and arsenic were respectively removed more than 90 96 from the molten copper, and their high eliminations are discussed by application of the transitory and permanent reaction model with the flux injection, which was presented by T. Lehner.

Jan 1, 1983

By Thomas P. Mucho

Cable bolts are emerging as the newest ?twist? for roof support in U.S. underground coal mines. For decades cable bolts installed in underground metal mines in the United States and Canada used cement-based grouts for anchoring. The cement anchoring process, because of the time and expense for installation, made cable bolts impractical for use in coal mines. Today, the introduction of resin-anchored cable bolts provides a system more consistent with tradi­tional U.S. coal mine roof bolting practices and requirements. Expecta­tions are that the utilization of cable bolts for a number of U.S. mining applications will expand, particularly in coal mining.

Jan 1, 1998

By S. J. Oosthuizen

This article explores the Fray Farthing Chen (FFC) Cambridge process, a novel method for the electrochemical deoxidation of metal oxides in molten salt, discovered at the University of Cambridge in 1997. The process was hailed as a highly promising, potentially low cost, novel method for the production of titanium metal direct from its oxides. The article should inform researchers in the field of some of the challenges in the commercialization of a novel, high profile process involving multiple stakeholders. The author, former senior process engineer at British Titanium Plc, the company originally tasked with commercializing titanium production via the FFC Cambridge process, reviews the latest literature and discusses past and present progress in the pursuit of low cost titanium metal via this process. Topics explored include the history of the process, attempts at commercialization, NASA?s alternative application, and present status of the process. Keywords FFC Cambridge, titanium, molten salt.

Jan 1, 2011

By R. G. Swanton

The Bureau of Mines is investigating the leaching of phosphate values from Florida phosphatic clay wastes using sulfuric acid (H2SO4) as the leaching agent and methanol as the solvent. Acid-alcohol leaching studies were done using pure crystalline apatite to investigate potential causes for low extractions. It was found that a barrier layer formed on the surface of the apatite. Initial discovery of the barrier layer was made by analyzing pure apatite samples before and after leaching using an optical microscope. Subsequent Fourier Transform Infrared (FT-IR) analyses proved the coating was calcium sulfate hemihydrate (CaSO4-1/2H2O) and that unreacted apatite existed beneath the coating. Scanning electron microscope (SEM) photographs depict the CaSO4-1/2H2O morphology as long slender crystals adhering to the apatite surface. It was also shown that grinding the leached tailings and leaching again in the H2SO4-methanol system resulted in additional phosphate extraction.

Jan 1, 1991

By Jeffrey L. Pagnutti

Train derailment can lead to loss of capital, damage to the environment, and loss of life. Machinery condition monitoring techniques can be used to develop a structural health monitoring system for railway track to detect faults at the incipient stage, before catastrophic failure occurs. This study uses vibration measurements from a novel material haulage unit to develop a decision support system for railway track maintenance. A variety of feature sets and classifiers were compared to determine the optimal configuration for fault detection. The results highlight the shortcomings and advantages of certain methods and describe the process in which the optimal result was obtained. The Parzen data descriptor paired with a refined statistical feature set performed the task of fault detection with less than five percent false positive and false negative classification error. Overall, the outcome of these experiments indicated that condition monitoring of railway systems is a promising approach for fault detection and has the potential to avoid catastrophic failure.

May 1, 2013

By Anna M. Ferrero

Stability condition of underground excavations have to be assessed to guarantee safe operations within the quarrying working areas. This objective requires a reliable assessment of the rock mass natural state of stress and of the stress redistribution induced by the excavations. This goal is often complicated by difficult geological conditions induced by tectonic stresses, complex topographies and large and irregular excavation geometries. Consequently, the acting state of stress needs to be measured by specific in situ measurement devices. This work refers on an in situ measurements campaign carried out by CSIRO tests in an underground quarry located in the Carrara marble basin. The difficult path carried out for interpretation of the measurements is described in this paper. In particular, the numerical modeling performed using the Boundary Element Method (BEM) first, to study the influence of both surface topography and excavation geometry and then the Distinct Element Method (DEM) to evaluate the influence of rock discontinuities in the measurement zone are illustrated in this work. Parametrical analysis of the rock mass mechanical features is also described in order to calibrate the numerical models and analyze the experimental results. The work has been carried out trough several phases, which are: characterization of the rock mass through geostructural surveys: this allowed us to classify the rock mass and determine the mechanical and physical parameters necessary for modeling; on-site measurement of stress levels through the application of over coring techniques; numerical analyses for the simulation of excavation phases, using the Examine3D (BEM) engineering analysis code. comparison between the measured stress levels and those numerically calculated and subsequent calibration of the BEM model; Numerical model of the forecasted excavation based on the calibrated (BEM) model.

May 1, 2009

By J. D. Megeath

In the October 1988 issue of MINING ENGINEERING, J.G. Wargo's paper discusses the problem of measuring and analyzing permeability, porosity, and fracturing in its relation to in situ leaching of disseminated gold deposits. This paper made me suspect that a good deal of information and analysis may have been done on this in reverse in the petroleum industry. Some years ago, I was involved with the US Geological Survey in a project studying the Devonian shale of the eastern United States. The Devonian shale contains gas deposits that have the characteristic of slowly seeping gas over a very long time period. To understand the rate of seepage, considerable study and analysis was done on the interrelationship of porosity, permeability, and fracturing. The purpose was to find out how and why the gas could escape in the varying rates found in wells throughout the formation. It strikes me that this is the mirror image of the problem faced in attempting to understand how a cyanide solution will travel into a deposit. To possibly invent our own personal wheel a little faster, I would suggest a look at the work done on the Devonian shale. Some of it is contained in "Estimates of Unconventional Natural-Gas Resources of the Devonian Shale," US Geological Survey Open-file Report 82-474, 1982, and "Additional Data for the Estimates of Unconventional Natural-Gas Resources of the Devonian Shale," Open-file Report 83-676, 1983. It is entirely possible that some of this previous work could shorten the time required to make in situ leaching of disseminated gold deposits a profitable technique.

Jan 1, 1990