Search Documents

By Jamal Rostami, Richard Kastner, Ahmad Ramezanzadeh

Improving the accuracy of the performance prediction models for hard rock Tunnel Boring Machines (TBMs) is important in estimation of the schedule and cost of tunnelling in related projects. The effects of rock mass on performance of TBMs has been studied extensively, yet due to the complex nature of the process, impact of many parameters influencing machine advance rate are not very clear and there is still room for improvements. More accurate estimates can be obtained by better understanding of operating parameters in various geological conditions and can lead to matching machine specifications with job conditions, optimizing machine performance, and avoiding long delays and downtime for increased productivity. This paper will offer review of two case histories including Queens Water tunnel in New York and KCRC project in Hong Kong. The analysis of the available field data, including the geological back mapping and results of laboratory testing of rock mechanical properties, machine operational parameters and achieved rate of penetration will be presented. This includes statistical analysis of available field data to provide a better understanding of the influence of rock mass properties on performance of hard rock TBMs as well as related formulas to improve performance estimates.

Jan 1, 2005

By J Zhou, D M. Hunter, S M. Iveson, K P. Galvin

The REFLUX Classifier is used to perform particle separations on the basis of density utilising a set of parallel inclined channels positioned above a vertical fluidised section. In continuous mode, feed enters part way up the vertical section, while fluidisation water is introduced from below. Lower density particles are conveyed upwards and collected in an overflow stream, while high density particles segregate onto the inclined surfaces, settle to the base of the system and empty via an underflow stream. Pressure transducers are used to measure the suspension density in the vertical section. This suspension density is maintained by a pneumatically controlled underflow valve to maintain a target suspension density or ‘set point’.Previously, Galvin et al (2010) demonstrated the significant improvement achieved via a new laminar-shear separation mechanism, achieved by utilising closely spaced inclined channels in the REFLUX Classifier. For the separation of low-density coal particles from mineral matter, a channel spacing of 6 mm proved effective; however, for the separation of gangue minerals from much higher density minerals such as iron ore, the shear-induced lift needs to be even higher. In this paper, we examine the influence of two different channel widths on the continuous processing of an industrial iron ore feed in the REFLUX Classifier. It was found that when moving from 6.0 mm to 3.0 mm channels, the ability of the system to reject coarser gangue material and retain finer high density material across a particle size range from 0.125 to 1.0 mm was increased, resulting in a higher grade product.CITATION:Hunter, D M, Zhou, J, Iveson, S M and Galvin, K P, 2017. Influence of shear rate on separation of iron ore fines using the REFLUXTM Classifier, in Proceedings Iron Ore 2017, pp 205–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Fumihiko Sumiya, Hideki Hamashima, Shigeru Itoh, Shinya Tanaka

The detonation characteristics of non-ideal explosives, especially the emulsion explosives, are critically affected by the confinement of case. In this study, we focused the shock wave propagating in case as confinement factor. Therefore, the objective of this study was to obtain a better understanding of the influence of shock wave propagating in case on the detonation characteristics of explosives in laboratory scale.

Jan 1, 2007

By H. M. Chikashi

Keywords: Pyrometallurgy, furnace, bath agitation, regression analysis, entrainment This paper presents the results of linear regression analysis of the influence that each component of slag has on the losses of copper in slag-cleaning-furnace slag. Data used for the analysis are actual plant data collected over the past two years of operation. Facts obtained from the study will be helpful for smelter management to control these components in the flash smelting furnace feed and slag, to levels which will enable better control of copper in slag, and smoother operation of the KCM slag-cleaning furnace.

Jan 1, 2011

By R. R. Tatiya

Data obtained from a copper mine were used in a comparative study of the reserve estimates generated by applying geostatistical methods to surface borehole data, underground core drilling results and assay values from chip sampling. Global estimation of the deposit performed by kriging of the low-density sampling data from the surface boreholes did not provide reliable results, but could identify the potentially mineralised zones. The reserve generated from core drilling results correlated well with that estimated from chip sample data and with that estimated by the conventional methods used at the mine. A satisfactory reserve evaluation could, therefore, be obtained by kriging of the data from the underground core drilling alone, provided that a systematic sampling procedure was adopted. Estimates based on chip sampling information could be used as a check, which could avoid the current practice of chip sampling of most of the mine workings. The aim should be to develop a semi-variogram for the deposit, which could be used to estimate the reserves by kriging

Jun 19, 1905

By Mariana Carla Mendes Rodrigues

The present study deals with the effects of strain rate on the functional behavior of NiTi thin wires. The samples, in the austenitic condition at room temperature, were mechanically cycled 20 times by loading up to 6% strain followed by complete unloading, at 25°C. Four different quasi-static strain rates were assessed: 1x10-4, 1x10-3, 1x10-2 and 5x10-2s-1. The functional properties are described by means of critical stress to induce martensite, stress at maximum strain, energy dissipated per cycle and residual strain. The sensitivity of repeated cyclic deformation to strain rate is also analyzed in terms of phase stability. The results show that the fluctuation in the loading plateau, due to non-homogeneous transformation, increases with increasing strain rate. During cycling, it is observed that higher strain rates result in lower critical stress to induce martensite after the 5th cycle. However, the stress at maximum strain is higher at high strain rates, regardless the number of cycles. The accumulation of residual strain also increases with the strain rate due to the higher applied stress. During unloading, both the elastic deformation of stress-induced martensite and the reverse transformation seem to overlap at high strain rates. The dissipated energy behavior changes between the 1st and 20th cycle. No martensite is stabilized after training, but the intensity of the X-ray diffraction peaks of austenite increases with strain rate, as a result of stress relaxation.

Aug 17, 2017

By Daniel Su

Following several roof falls in the E3 longwall development of a Consol Pennsylvania Coal Company underground coal mine, an underground roof geology reconnaissance program consisting of twenty-nine 20-foot deep roof holes had identified the presence of thick sandstone layers with abundant shale and micaceous streaks. The base of the sandstone was 4 to 8 feet above the roof line within the fall areas. The presence of micaceous streaks created extremely pronounced planes of weakness in the sandstone. A structural irregularity, which extends into the E4 and E5 developments, exists between crosscuts I 1 and 30,where all roof falls occurred. Immediately to the east of this structural irregularity lies a huge syncline. The presence of thick sandstone units within the typically all shale environment and within such a structural irregularity helps to maximize stress concentration and creates closely spaced joints in the sandstone, which explains why many cracks are present in the macroscopically massive sandstone upon development. The approaching E2 longwall gob to the south and on the down-dip side, on the other hand, provided horizontal stress relief in the sandstone, which helps to explain the many roof falls in the E3 development that occurred during or immediately after the formation of the E2 gob. Finite element modeling confirmed the presence of such horizontal stress relief. Since the E3 longwall was a right-handed face, stress concentration was expected at the longwall headgate T -junctions, and further delamination of the sandstone was expected upon arrival of the E3 longwall face. Based on the results of the roof geology reconnaissance program and a roof stability analysis that took into account up to eleven parameters, supplemental headgate and track roof support consisting of 16-foot and 20-foot long cable bolts was successfully implemented within the zone of thick sandstone with micaceous streaks and structural irregularity and at other potential roof instability areas along the E3 development. The cable bolts were designed to be anchored at least 4 feet above the sandstone unit into the mostly competent sandy shale layers. No headgate roof control problem was reported within the sandstone and structural irregularity zone during E3 and the subsequent E4 longwall extractions.

Jan 1, 2002

By M. Krasowska

Dynamics of collision and kinetics of the bubble attachment to hydrophobic solid plates (Teflon) of different surface roughness were investigated. The experiments were carried out in such a way that probability of the collision and probability that the detachment will not occur were equal always 100%. Thus, it was possible to determine effect of the surface roughness on the bubble attachment (three phase contact formation, TPC) only. A high-speed camera (1182 Hz) was used to record the velocity variations, bouncing and time of attachment of the bubble colliding with Teflon plates having different surface roughness (5 different plates). Roughness of the plate surfaces was modified in a mechanical way using different abrasive papers. It was found that the roughness had a crucial influence on the time-scale of the TPC formation and attachment of the bubble colliding with the Teflon plates. Despite high hydrophobicity of all plates (contact angles 1100 -115º) it was observed that at the smoothest surfaces (called "Teflon I" and "Teflon II" and having surface roughness below 1 um) there was no attachment during the bubble first collisions. Prior to the attachment four or more "approach?bouncing" cycles of the colliding bubble were observed there and simultaneously the bubble shape varied rapidly within time intervals below 0.85 ms. Time of contact of the colliding bubble with the Teflon plates was very short; 2-3 ms. These results indicate that during that short time of the collision the liquid layer separating the colliding bubble and the solid surface did not reach a critical thickness of its rupture.

Jan 1, 2006

By Tian Sugui

By means of the measurement of the enduring property and microstructure observation, an investigation has been made into the influences of the element Re and TCP phase on the enduring property of the single crystal nickel base superalloys. Results show that the needle-like TCP phase is precipitated along the <110> orientation on {111} planes in Re-containing/free superalloys during the long term aging, the TCP phase is identified as µ phase, and the precipitated µ phase in 4.5%Re alloy is gradually spheroidized during aging. Thereinto, the needle-like µ phase may obviously decrease the enduring lifetimes of the alloys due to the consumption of the refractory elements and the effect of the stress concentration. But the stress concentration is not easily generated in the regions near the spherical-like µ phase, which is a main reason of reducing the enduring lifetime of 4.5%Re alloy to a small extent.

Jan 1, 2010

By Man-Chao He

One of the critical problems involved in deep coalmines is unusual gas emissions. Many researchers agree that there is a relationship between coal gas emissions and geological features such as tectonics or geological disturbances, gas content, properties of the coal and rock and the mininginduced stress state in the coal seam and rock. Thus, the present paper intends to investigate complex mechanical phenomena during the process of gas emission in underground coal-mines. A program of laboratory testing was undertaken to study the effects of temperature and pressure on mechanisms of gas emission. It must be noted that this paper describes new techniques developed to simultaneously measure deformation and gas pressure, as well as flux during the test, taking the characteristics of gas transport into consideration under certain temperature and pressure conditions. The results indicate that under certain temperature and pressure conditions, gases adsorbed to coal start to desorb, and increase the pore pressure. High pressure gases entering coal fractures can generate high tensile stresses near the crack tips, leading to crack propagation and coalescence, which in turn can cause the specimen to dilate. From the experimental viewpoint, these test results may help us discern why mining seismic events can trigger gas emissions.

Aug 1, 2013

By Francis Foley

INTRODUCTION DURING the summer of 1919, the late Dr. Henry M. Howe, then Chairman of the Division of Engineering of the National Research Council, organized a committee to obtain a better insight into the behavior of carbon steels under the influence of various treatments by a proper control of the time and temperature factors. During part of 1919 and 1920, work in connection with this investigation was carried on at Dr: Howe&apos;s laboratory at Bedford Hills, N. Y. During 1921 there was an enforced hiatus in the work, occasioned by the illness which resulted in Dr. Howe&apos;s death in 1922. At that time one of the present authors compiled the results of the work which had been done and this was published in 1923.1 Following the publication of this work, it seemed desirable to carry on in the same manner an investigation of steel of C 0.75 per cent., which steel had not been as fully treated as had the other steels of C 0.34 and 0.52 per cent., used in the published work. Furthermore, certain unusual results have been obtained in the treatment of C 0.52 per cent. steel by quenching and drawing, and repetition of this part of the work seemed advisable. This has been done during the past year at the School of Mines and Metallurgy of the University of Missouri at Rolla, Mo., by a cooperative undertaking of the School and the Bureau of Mines, working in conjunction with the Committee on Heat Treatment of Carbon Steels of the National Research Council. The present paper is a report of the results obtained in this work.

Jan 2, 1926

By HENRT M. HOWE

IN my original paper, Piping and Segregation in Steel Ingots, I pointed out1 among other things that, in view of the slighter stretching (virtual expansion) of the crust, and greater opportunity for sagging, there should be less piping in broad than in narrow ingots, and less in slowly-cooled ingots, e.g., those cast in pre-heated sand molds, than in those which cool quickly, e.g., those cast in iron molds. A. A. Stevenson2 said that neither of these predictions agreed with his own experience. In particular, in a picture which he showed of a wide and of a narrow ingot cast from the same ladleful of steel,, the wide ingot had certainly piped much more deeply than the narrow one. At the time I did not see the explanation of these discrepancies, but further reflection makes it evident. One of the most important elements in determining the depth of the pipe is the degree of " top-lag," that is, the degree to which the solidification of the top of the ingot lags behind that of the bottom. &apos;Through this lagging the steel of the upper part of the ingot is able to run down and fill the pipe below as fast as it forms. To the importance of this lagging I called attention in my original paper.&apos; Sand vs. Iron Molds.-If we compare two like ingots, one cast in an iron and the other in a sand mold, we see that the top-lag&apos; is much greater in the former than in the latter, be¬cause in the former the lower part of the ingot is cooling off fast while the metal is running into the upper part. It is perhaps easier to look at this as a case of the solidification of the hot-

Dec 1, 1909

By Hiren J. Shah

The urban environment and geology create unique challenges for design and construction of deep foundations. The effect of these is prominently experienced in New York City. Three such project case histories are presented in this paper. The first project is a multi-use development. Relatively unusual glacial geology was observed at the site during the subsurface investigation phase. This played an important role in the selection of deep foundations as well as during construction. The design and construction aspects of the pile foundations, settlement estimates, a pile drive test program during design, piling equipment and production pile installation are discussed herein. A relatively smaller project is the second case history. A combination of drilled and driven deep foundations was employed in one area of the project due to its unique conditions. In another area of the project, an addition to a structure required the use of supplemental foundations to resist new additional loading. Tight space and load sharing with the existing foundations were important considerations in the design and construction. Finite element modeling of the existing and completed structure was performed which was an interesting aspect of the project. The third project case history involves a very large multi-billion dollar project in which various different types of deep foundation elements were used. The aspects requiring the use of such a variety of types and sizes of deep foundation elements included: geologic conditions, re-use of existing foundations, protection of adjacent infrastructure, construction staging, restricted space, loads, deep excavations, cost and schedule.

Jan 1, 2011

By D J. Williams, M S. Zbik, A Shokouhi

There is a considerable difference in the particle size distribution (PSD) of clay mineral-rich coarse coal reject with variations in the test moisture state and the chemistry of the water used for testing. The coarse coal reject tested were collected from Jeebropilly Mine, located in the Ipswich Coalfields of south-eastern Queensland. Differences between the results of dry and wet sieving analysis indicate a significant breakdown of the clay mineral-rich coarse coal reject on wetting-up. Wet sieving caused a breakdown of the gravel-sized fraction to silt and clay size without significant breakdown to sand size. There is also a considerable variation in the results of hydrometer analyses of the clay mineral-rich coarse coal reject with variations in the chemistry of the water used, particularly at the fine end of the particle size range. The waters used included tap water, coal processing water and deionised water. In addition, the method of dispersion applied prior to hydrometer analysis can have a significant effect on the PSD of clay mineral-rich coarse coal reject, with boiling and sonic vibration causing the most breakdown of the clay particles. This paper describes the testing methodology used and the test results obtained, and attempts to explain the results in terms of clay mineralogy and water chemistry.CITATION:Shokouhi, A, Williams, D J and Zbik, M S, 2015. Influence of water on particle size distribution of clay mineral-rich coarse coal reject, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 239–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By S. Borle

The microstructural features produced in friction stir welded AZ31, AZ80 and AZ91 alloys are examined when different welding parameters are applied. The microstructures primarily consist of a-Mg grains with a-Mg + Mg17A112 colonies, however melted films of Mg17A112 are produced in AZ91 alloy when high rotation speeds are applied. When the rotation speeds are slow, or the travel speeds are fast the Mg17A112 were incorporated into the stir zone, however they do not exhibit an elongated lamellar morphology associated with melted films. In the case of AZ80, the extruded base material contains a smaller fraction of Mg17A112 and few of these phases are observed in the stir zones. The results are explained based on the dissolution rate and melting temperatures of Mg17A112 controlling the overall morophology and fraction of phases in the stir zone.

Jan 1, 2011

By D. Yu, Y. Thibault, D. Paktunc

"Prereduction and flux-aided direct reduction of chromite provide significant advantages in reducing energy consumption and greenhouse gas emissions during ferrochrome production. In this investigation, a comparative evaluation of the influences of several alkali fluxes was carried out based on experimental observations supplemented by advanced material characterization and thermodynamic predictions. Direct reduction of a chromite ore with alkali fluxes at 1300°C for 1 hour produced (Cr,Fe)7C3 type alloys with Cr/Fe mass ratios from 0.7 to 2.3. Among the alkali fluxes, reduction aided by NaOH resulted in a high degree (85%) of Cr metallization with the ferrochrome alloy being Cr4.2–4.6Fe2.4–2.8C3. The formation of liquid slag, which facilitated Cr metallization, was limited by the formation of NaAlO2 between 800 and 1300°C. This, in turn, restricted the collection and transport of the charged ionic Cr species (i.e. O2–) to graphite particles. Under the conditions studied, ferrochrome particles were often small and largely unliberated, which would make the physical recovery of ferrochrome challenging. At 1400°C, the amount of liquid slag increased, enabling the growth of alloy particles. Direct reduction of chromite aided by NaOH is promising as an alternative technology to conventional flux-based smelting in electric arc furnaces. IntroductionConventional smelting processes are energyintensive (Riekkola-Vanhanen, 1999) with the energy requirements greater than 4 MWh/t (Naiker and Riley, 2006; Beukes, van Zyl, and Neizel, 2015), and the greenhouse gas emissions can be significant, exceeding 10.5 t CO2 per ton Cr in ferrochrome produced (International Chromium Development Association, 2016). These include emissions occurring on-site (smelter), emissions due to electricity production, and emissions due to upstream processes. Overall energy requirements are influenced by the degree of prereduction and smelter charge temperature. Significant reduction in electricity consumption can be realized if the charge is prereduced before feeding to the submerged arc furnace (Niayesh and Fletcher, 1986). This consideration has led to the development of several prereduction technologies, with the most important example being the Premus process. In comparison to the conventional smelting processes, this prereduction process lowers the overall energy consumption and greenhouse gas emissions by about one-third (Naiker, 2007)."

Dec 1, 2018

The impact of a methane explosion on mining operations cannot be over-emphasized. The explosion is a result of rapid combustion when a methane/air mixture is ignited by an unexpected energy release, such as a mine fire, electrical arc or sparks caused by frictions or rock falls. In most cases, an ignition of methane/air mixture could result in a deflagration other than detonation. Resulting flames and overpressure induced by a methane deflagration will harm neighboring miners and local ventilation control devices.. ,It is essential that the mechanism of an explosion and associated destructiveness be fully understood. This research seeks to predict an influence region of an incident happened within a representative underground mine geometry. The most common geometric changes in an underground coal mine are bends, regulators/doors, obstacle in airways and changes in sectional area. These geometric changes could result in an attenuation of the flame and pressure wave as a result of a methane deflagration. A study of this phenomenon could enable mine planners to have better understanding of the over-pressure redistribution due to the explosion. Both numerical and experimental work has been done in this study to ascertain a better insight of this potentially devastating event. The experimental data are also used to validate the turbulence and combustion models used in this test.

Feb 23, 2014

By Leandro Brunholi Ramos

Foi estudado o efeito da temperatura no comportamento à corrosão sob tensão do aço inoxidável dúplex AISI 318 em solução contendo 115.000 ppm de cloreto, pH4 a temperatura ambiente e a 70°C. Ensaios de tração com baixa de taxa de deformação foram realizados. Foi avaliada a susceptibilidade do aço inoxidável dúplex AISI 318 à corrosão sob tensão no potencial de circuito aberto e em vários potenciais anódicos e catódicos. Os resultados mostraram que a redução do alongamento variou com o potencial aplicado. Os resultados experimentais mostraram que o aço AISI 318 ficou imune à corrosão sob tensão em potencial entre -750 mVECS e 1.000 mVECS na temperatura ambiente e entre -650 e -100mVECS para a temperatura de 70°C. Em potenciais maiores que o potencial de pite observou-se uma redução drástica no alongamento em ambas as temperaturas. No entanto, quando os potenciais aplicados foram abaixo de -650 mVECS para a temperatura de 70°C e -750mVECS para a temperatura ambiente, houve uma redução no alongamento final até a ruptura, provavelmente através do processo de fragilização por hidrogênio.

Aug 8, 2018

By Diego Pinheiro Aun

Neste trabalho, foi investigada a influência da textura de fitas de NiTi superelástico no início do processo de cristalização de um revestimento de TiO2 flexível. Foram utilizadas a calorimetria diferencial, cartografia Raman e difração de raios X para o estudo. Foi mostrado que existe uma influência significativa da textura do substrato no crescimento de grãos de anatase e rutila no filme de TiO2. Amostras com menor rugosidade apresentaram grãos mais desenvolvidos para todas as temperaturas de cristalização. Mostrou-se também que o substrato de NiTi promoveu a formação de TiO2 rutila em temperaturas abaixo daquelas observadas para a cristalização de pós.

Aug 16, 2017

By Alana Pereira Ramos

O efeito de memória de forma tem como principal objetivo a recuperação da forma por meio de aquecimento acima das temperaturas críticas de transformação. Fitas da liga Ti43,5Cu37,8Ni18,7 foram preparadas através do processo melt spinnig com velocidade da roda de 21 m/s e 63 m/s. As fitas foram tratadas termicamente numa temperatura de 700°C por 15 minutos em forno e resfriadas ao ar. A caracterização das fitas foi feita por calorimetria diferencial de varredura (DSC) e análise por difração de raios X (DRX). Foi observado que com uma menor velocidade de rotação da roda (21 m/s) a fita apresentou-se totalmente cristalina, e quando aumentou-se a velocidade linear da roda para 63 m/s a fita apresentou-se completamente amorfa. Após o tratamento térmico todas as fitas apresentaram as transformações martensíticas e auteníticas. Observou-se que a velocidade da roda tem grande influência nas temperaturas de transformação, chegando à variação de aproximadamente 7°C. O tratamento térmico remove todos os defeitos produzidos pelo processo de solidificação rápida e produz um rápido crescimento de grão, favorecendo ao aumento das temperaturas de transformação.

Aug 8, 2018