Search Documents

By Wendy L. Mathieson

The Bonneville Power Administration (BPA) will build about 500 miles of new 500-kV transmission lines in the next 5 years. Many new lattice towers will be built in remote locations or in environmentally sensitive areas. Therefore, micropile foundations were designed that could be installed in remote areas, in variable subsurface conditions, and in a manner that would reduce excavation volumes and potential erosion concerns. Typical lattice tower foundation axial loads range between 75 and 1,500 kips (300 to 6,700 kilonewtons [kN]) per leg, with uplift loads being slightly less than compressive loads. Lateral loads range from 5 to 320 kips (20 to 1,400 kN) per leg. Full-scale axial and lateral load tests were conducted in geologically representative soil units during the micropile design for the 9-mile-long (14-kilometer [km]), Kangley-Echo Lake transmission line that extends through a protected watershed east of Seattle, Washington. Micropile foundations for single and double circuit suspension and dead end towers were designed using these load test data.

Jan 1, 2004

By Stefan Basista, Janusz Tomala

Modern constructions of electric ferroalloy furnaces are still based on applying in the lower "liquid" areas the standard carbon materials. What can be illustrated by the experience from several years, in the part of tap hole, hearth walls and bottom, is that so-called carbon or semigraphite microporous materials are successfully being applied. These materials, compared to the standard carbon, give better resistance to the attack by liquid metal and other wear factors. Generally this group includes materials characterised by considerable share of pores of diameters below1µm (significantly exceeding 90% of total porosity). The microporosity increases the resistance to the infiltration of the liquid metal. The effect of microporosity can be obtained by introducing silicon (or its compound) additive to materials based on electrically (or gas) calcined anthracites, electrographite and binder. Moreover, by introducing other ceramic additives, the microporous materials are more resistant to dissolution by the liquid metal. Observing the trends of "improving the materials" in the last years, it is clearly seen that the share of non-carbon additives is bigger and bigger, so we can reasonably speak of rather carbon-ceramic materials. In this paper, the survey of the most important quality criteria, which must be met by the carbon furnace linings, as well as the new testing methods will be presented.

Jan 1, 2007

By K. Ananthanarayanan, R. I. L. Guthrie, S. A. Argyropoulos

"The low cost and availability of micro-computers and their peripherals provides the metallurgical engineer with the opportunity to use such computers in a wide variety of applications. In this paper, the authors describe the development of a low cost data acquisition system capable of measuring up to 8 analogue channels at a sampling rate of up to 5000 measure mentsper second. This system is equipped with proper hardware and software so that the micro-computer can be linked to a central computer facility such as the McGill System for Interactive Computing (MUSIC). This central computer facility is supported by an AMDAHL V7 computer. Using the present interface, communication rates between the microcomputer and the central computing facility can be as high as 9600 (baud).The above mentioned data acquisition system is currently used for monitoring dissolution kinetics of ferro-alloy additions in liquid steel. In addition to this, special software has been developed which enables the user of this system to monitor solidification rates of ingots, etc. As economic considerations are always important, comparisons have been made with existing recorders which show that the cost Of the present system is only 30 per cent more than a two-pen strip chart recorder.RESUMELa disponibilité et le bas prix des micro-ordinateurs et de leurs périphériques permet à l'ingénieur métallurgiste d'utiliser de tels ordinateurs pour diverses applications. Dans ce rapport, les auteurs décrivent le développement d'un système d bas prix pour l'acquisition des données, capable de mesurer jusqu'à huit canaux analogues jusqu’à une vitesse de 5000 mesures par seconde. Ce système est équipe avec son propre ""hardware"" et ""Software"" qui relient le micro-ordinateur d’un ordinateur central, comme le système de McGill pour computations réciproques (MUSIC). Ce central d'ordinateurs est soutenu par l'ordinateur AMDAHL V7. Utilisant cet "" interface"", la vitesse de communication entre Ie micro-ordinateur et l'ordinateur central peut atteindre jusqu'd 9600 (baud)."

Jan 1, 1980

By G. O. Oniyide, H. Yilmaz

The South African platinum mines in the Bushveld Complex (BC) have unique features that distinguish them from the gold mines. They have a higher horizontal stress closer to the surface, lower occurrence of seismic activity (caused mainly by pillar failure), and are sited in an area of high geothermal gradient. One of the future challenges of platinum mining is the increasing temperatures as the mining depth increases. High temperatures invariably bring about higher ventilation costs and require different approaches to human factors and ergonomics. Excavation stability would also be another area of concern due to increasing stresses. In this investigation, the effect of temperature on the physical and chemical properties of selected Bushveld rocks (chromitite, pyroxenite, norite, leuconorite, gabbronorite, mottled anorthosite, varitextured anorthosite, granite, and granofels) was studied by means of optical microscopy and scanning electron microscopy using energy-dispersive Xray spectrometry (SEM-EDX). The rock specimens were heated in a temperature-controlled oven a rate of 2°C /min to 50°C, 100°C, and 140°C and kept at temperature for five consecutive days. Samples were allowed to cool to ambient temperature (approximately 20°C) before image capturing. Micrographs of the specimens were taken before and after heat treatment. All the SEM samples were also subjected to heating and cooling on alternate days for ten days in order to observe the effect of repeated heating and cooling on the rocks. The results of the optical microscopy analyses showed minor physical changes in the rocks. The SEM images revealed that cracks initiating at lower temperatures extend with increasing temperature. The chemical analyses showed that the temperature range considered in this research is not high enough to induce changes in the chemical composition of rock samples.

Jan 1, 2016

By H. S. Martin

ALTHOUGH it was known some years ago at the- Utah Copper Co. mills that fine grinding improved flotation recoveries, no accurate data were available until recently as to just how far the grinding could be carried economically. In 1923 the ultimate degree of fineness for flotation feed was supposed to be about 10 per cent. on 65 mesh, with approximately 55 per cent. through 200 mesh, which meant that most of the mineral would pass 100 mesh. At this time Garfield and Wilfley tables were used ahead of flotation and a good deal of the coarse mineral removed prior to the ball mill regrind. Shortly afterwards, mill-scale tests developed the fact that on a feed containing not over 10 per cent. +65¬mesh material flotation alone would give a copper recovery equal to that obtained by the combination of tables and flotation, but that on much coarser feed the recovery with flotation alone was lowered. This was at a time when all the sulfide minerals were floated if possible, so that the only requisite was to grind fine enough to free the mineral from gangue. EARLIEST USE op MICROSCOPIC EXAMINATION OF TAILINGS As early as 1921, the writer had attempted to determine by chemical analysis the relative proportions of copper minerals in tailings from an ore that made extremely poor flotation results. Chemical analysis was not satisfactory or conclusive, and samples of these tailings were sent to the U. S. Bureau of Mines Station at the University of Utah for micro-scopic examination. The question at that time was to determine, if possible, which copper minerals had been lost and why, but R. E. Head, in his report, revealed other interesting data. He said in part: Briefly stated, the mineral particles or grains may be classified into separate groups as follows: 1. Free grains of pyrite, chalcopyrite, chalcocite and bornite, respectively, which contain no other included sulfides; 2. Grains in which all three of the copper sulfides are represented (the core may he of chalcopyrite, partially altered to bornite, these two minerals being entirely surrounded by a shell of chalcocite); 3. Grains composed of equal amounts of bornite and chalcocite or chalcopyrite and chalcocite.

Jan 1, 1929

By Gregory B. Poole

Data collected with 16K sampling at a variety of blasting sites (construction, quarry, trench, mine) and monitoring locations was analyzed to effectively show the 16 different 1K readings all based on the microsecond that the unit went into monitoring.

Feb 1, 2020

By Will S. Pettitt

Fracture Network Engineering (FNE) is the engineering design of rock mass disturbance through the use of advanced techniques to model fractured rock masses numerically, and then correlate field observations with simulated fractures generated within the models. Microseismic (MS) monitoring is a standard tool for evaluating the geometry and evolution of the fracture network induced during a hydraulic treatment, principally by source locating MS hypocenters and visualizing these with respect to the treatment volume and infrastructure (Figure 1). The integrated use of Synthetic Rock Mass (SRM) modeling of the hydrofracturing with Enhanced Microseismic Analysis (EMA) provides a feedback loop in which the SRM is constrained by the information provided by the MS data and the in-situ behavior of the fracture network is better understood, leading to informed decisions on future field operations. This paper discusses the technologies used in FNE and some of the developmental challenges we face in order to provide a more efficient and robust application of the approach. One particular challenge is the accurate representation of MS source data within the models (locations, magnitudes and mechanisms), and the ability to correlate these data effectively with field results. This challenge is being overcome by the development of more efficient numerical modeling algorithms, providing simulations in three dimensions at reservoir scale, combined with validation of these algorithms using laboratory and field case studies.

Jun 1, 2012

By Wilson Blake

This report presents the results of a 7-year Bureau of Mines program to review, revise, and make an effective engineering tool of the microseismic method of determining the stability of rock structures. The program consisted of developing new microseismic equipment and data analysis techniques and extensive field investigations to demonstrate the effectiveness and potential of the broad-band microseismic method. The guidelines for choosing the components of a microseismic system are presented along with approximate cost figures. Different microseismic systems are discussed, including completely automated systems. Procedures for conducting microseismic investigations and analyzing microseismic data are discussed in detail. Field situations which show the full value of the microseismic technique as an engineering tool are described.

Jan 1, 1974

By Varadarajan Seshadri

Geometallurgical characterization of iron ore which is a raw material for Iron making as in the case of charcoal blast furnaces operating in Brazil or for production of agglomerates such as iron ore sinter which serves as burden material for blast furnces of high productivity or pellets extensively used in the direct reduction processes all over the world in the iron and steel industry. Selection of proper raw material after due characterization should lead to an improvement of the productivity of the respective processes The usual classification of quality of iron ore is uniquely based on chemical analysis, granulometric and physical parameters. However not much emphasis has been given to the structural characteristics which also are important in the processes. Different typological categories of Brazilian iron ores have been used in the characterization . For instance, several kinds of hematite crystals like specularite, martite and microgranular hematite, etc with variable crystal sizes are found in the different ore types. They are also composed of different of fabrics and types of accessorial mineralogical constituents and have different porosities, pore diameters, etc which influence the cold and the hot agglomeration stages of the ore fines, and also chracteristics such as reducibility, decrepitation etc, important for assessment of quality of iron ores. . The first step for attaining a good characterization of ores is to know in detail about the structure of the deposit, shape of the body, types of iron ores and their distribution. This requires a geological-structural study and the mapping of the bodies using mineralogical criteria for typological classification of ores. followed by structural characterization of materials in stages of mining, comminution, screening and concentration processes. In this contribution a geometallurgical approach for quality control of Brazilian iron ores for sintering and pelletizing processes is highligted.

Jan 1, 2006

By J. D. Ecuyer, L&apos

he microstructure of galvanneal coatings formed on extra low carbon and interstitial free steel substrates has been characterized using electron microscopy (TEM and SEM) and x-ray diffraction. The coatings are found to consist of a mixture of gamma, delta and zeta phases, of which delta is the main constituent. The amounts of each phase influences the powdering resistance of the coating which was evaluated using reverse Olsen testing and 60" bending. For the three heat input conditions considered, IF coatings were always found to contain a significant amount of gamma and only those which retained zeta phase on the surface exhibited a satisfactory powdering resistance. In much the same way, ELC coatings with relatively thick gamma layers performed satisfactorily only when some zeta was retained. It was also found, however, that coatings with minimal zeta and gamma had an excellent powdering resistance. The latter coatings were produced under galvannealing conditions of lower relative heat input. These results indicate that in addition to the zinc bath composition, coating weight and galvanneal thermal cycle, the base steel chemistry also has an effect on the coating microstructure. Knowledge and control of all aspects of galvannealing is therefore essential to consistently produce acceptable coatings.

Jan 1, 1992

By I. A. Mwamba

Titanium aluminide of composition Ti-47.5 at.% Al was prepared by melting titanium and aluminium of commercial purity with additions of precious metals of 0, 0.2, 1, 1.5 and 2 at.% content. The microstructure, hardness and oxidation properties were assessed. It was found that at 47.5 at.% Al, the microstructure of plain TiAl alloys was duplex, consisting of duplex lamellar grains and ? grains. The lamellar grains consisted of alternating lamellae of ? (TiAl) and a2(Ti3Al), with overall aluminium content in the range of 43?47 at.%. The ? grains had a aluminium content above 50 at.%. The addition of precious metals to the TiAl alloy resulted in the formation of a new phase, with a high precious metal content, occurring mostly in the ?phase, without any major change to the microstructure. Increasing the amount of precious metals resulted in an increase of the new phase amount, at the expense of the ? phase. The hardness of the different alloys was around 300HV10. Overall, the research has shown that addition of precious metals to TiAl resulted in a slight increase in hardness and a significant improvement of the oxidation resistance. This shows that alloying TiAl with precious metals, at the addition levels investigated, does not alter the mechanical properties very much, but improves oxidation resistance.

Jan 1, 2012

By M. Fairman

The effect of welding speed on the microstructure of friction stir processed (FSPed) AZ31B-H24 magnesium alloy was studied using light microscopy, image analysis, and microhardness tests. The grain size of the magnesium alloy was observed to increase after FSP from about 3.5 µm in the base alloy to about 8 µm in the stir zone. The aspect ratio decreased from 1.60 to 1.55 towards the center of the stir zone. The changes in the grain size and shape caused the microhardness of the samples to drop significantly across the FSPed region from 75 HV in the base alloy to below 55 HV in the stir zone. Decreasing the welding speed increased the grain size due to a greater input of heat energy. The faster heating rate due to the lower welding speed caused a deeper penetration of the annealing effects of FSP. It was also observed that the annealing effects caused by FSP were less pronounced with increasing distance from the interface between the sample and pin tool shoulder. The Hall-Petch type relationship of the micro-indentation hardness as a function of the grain size was observed to hold true after FSP.

Jan 1, 2007

By R. Boom, L. Holappa

In the present paper, microstructure changes of solid-state reduction of industrial chromite pellets and lumpy ore were investigated with SEM/EPMA. To simulate the reactions in the packed bed zone of the Submerged Arc Furnace (SAF), carbon monoxide was used as the reducing agent, with the presence of graphite in proximity to chromite. The experiments were carried out at 1500 °C. Scanning electron microscopy was used to observe and analyse the structure and composition changes of the chromite samples. It was found that reduction of lumpy ore generally took place slower than that of pellet. In all samples, chromite reduction proceeded faster in the outer part of the sample than in the centre part. The reaction mechanism is discussed on the basis of experimental results and earlier investigations. The possibilities to optimize the FeCr production process are also discussed.

Jan 1, 2007

By O. F. Ochonogor

Laser metal deposition (LMD) is an additive manufacturing technique whereby a stream of metal powder is consolidated by a focused laser beam on the surface of a substrate or engineering component. The interaction zone between the laser beam and powder particles is scanned superficially, generating tracks of deposited material. The tracks are overlapped in a deposition strategy in accordance with slices of a CAD model. Successive layers of material are built up to fabricate a near net shape part. In this work, the technique is used to fabricate metal matrix composites (MMCs) by using an elementally blended feedstock combining metal and ceramic powders in the melt pool, which melt and solidify to create the required morphology. Ti6Al4V + TiC MMCs were produced with 10, 20, and 30 vol.% reinforcing ceramic, and Zr + TiC MMCs were fabricated with 10, 20, and 30 vol.% TiC. The deposited thin walls were analysed using optical microscopy, scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS), and indentation testing. In both systems, the analysis revealed the presence of partially melted TiC particles embedded in the metal matrix along with fine dendrites of re-solidified ceramic. The dendritic structures in the Ti-based composites were confirmed as TiC, whereas in the Zr-based composite the Zr metal reacts with theTiC to form ZrC, leaving Ti in solid solution. Both the MMCs show an increase in microhardness with increasing ceramic (carbide)content, reaching a peak HV0.1 value of 500 in the Zr- based MMC and HV0.1 of 550 in the Ti based MMC.

Jan 1, 2012

By K. Matsuura, M. Ohno, T. Tokunaga

"Recently, weight saving of automobiles has been strongly required to solve the global environmental problems. Mg alloys are one of the promising candidates as a new material for automobile components. However, the application of the Mg alloys is limited due to their poor corrosion resistance. In the authors’ preliminary study, an Al/Mg/Al clad sheet was fabricated by hot extrusion and subsequent hot forging. The clad sheet exhibited a high corrosion resistance and excellent super plasticity. More specifically, the elongation of the clad sheet was as high as 550%.Importantly, despite that the elongation of Al itself was only 40%without cladding with Mg, the ductility of Al was greatly improved in the form of the clad sheet. In the present study, in order to clarify the mechanism of the superplastic deformation of the Al part in the clad sheet, the microstructure evolution of the Al during the tensile de formation is investigated. The tensile tests were conducted at a temperature of 573 K and at a strain rateof1.0×10-3s-1. The Al exhibited fiber-type texture at the beginning of the tensile deformation, and brass-type texture after the elongation of 50%.INTRODUCTIONMg alloys have been gaining attention because of their excellent properties e.g. light weight, good recyclability and high electromagnetic shielding. However, their practical applications have been limited due to their poor corrosion resistance. In the authors’ previous study, in order to solve this problem, Al coating on Mg alloy by hot extrusion has been proposed, and the Al-coated Mg alloy plate was fabricated(Tokunaga, Matsuura, &Ohno,2012). The plate was hot-rolled and an Al/Mg/Al clad sheet was fabricated. No cracks or debondings were observed at the Al/Mg interface. The sheet exhibited a high corrosion resistance in a comparable level as pure Al. Also, the sheet exhibited a large and uniform elongation of 550%in a tensile test at a temperature of 573 K and at a strain rate of 1.0×10-3s-1without any breakings or debondings of the Al part(Tokunaga, Matsuura, &Ohno,2014).Mg alloys have been known to exhibit a superplastic characteristic when the grain size is small. However, it is known that the pure Al does not generally exhibit the super plasticity. As mentioned above, the Al-coated Mg alloy sheet exhibited 550% of elongation in the authors’ previous study (Tokunagaet al., 2014). However, the pure Al itself showed only 40% of elongation, while the Mg alloy itself exhibited 800% of elongation. Thus, it has been demonstrated that the pure Al was super plastically elongated when it was bonded with the Mg alloy. Generally, deformation mechanism of the super plasticity of the Mg alloy is known as a grain boundary sliding. On the other hand, the mechanism of the superplastic elongation of the pure Al is still unclear. The purpose of the present study is investigation of the deformation behavior of the Al part in the Al/Mg/Al clad sheet during tensile de formation."

Jan 1, 2018

By L. A. Matthews

The embrittlement of the Ti-6Al-4V alloy by hydrogen dosing at elevated temperature has been investigated. Metal coupons were subjected to isothermal treatments in a partial hydrogen atmosphere in the temperature range from 650ºC?950ºC and the degree of embrittlement after treatment was determined by drop-weight impact testing. Embrittlement was found to be inversely related to reaction temperature as a result of the combined effects of greater hydrogen absorption and titanium hydride precipitation at the lower isothermal temperatures. Keywords Titanium, hydrogen embrittlement, impact energy

Jan 1, 2011

E. E. THUM,* Salt Lake City, Utah (written discussion?).-While the present paper is confined exclusively to the microstructure of fusion welds, it may be of interest to draw attention to certain appearances existing in resistance welds such as spot or butt-welded joints produced by the Thomson process. For instance, a butt weld between two pieces of carbon tool steel (carbon about 0.90 per cent.) will show concentric ellipsoids of the various materials from pearlite to martensite. The surfaces of demarcation are quite well defined, the center of the ellipsoid being at the intersection of the axis of the piece and the plane of the weld. Often these unannealed welds show a troostitic center; evidently this core was not quenched as rapidly as the surrounding shell. Such specimens are beautiful samples for instruction purposes. An annealed butt weld of this kind will show a very well defined central ellipsoid of decarburized, materials. It is interesting to consider the reason why this change takes place. It must be understood that the heat is on the metal for a very short time, possibly 30 sec. It is therefore evident that the decarburization, or migration, of the carbon takes place with extreme rapidity. Since no blowholes are evident in a well-made butt weld, the deoxidizing air and the products of combustion must migrate with the highest speed; second, the carbon might migrate back into the stock; or, last, a large proportion of the pearlite may be extruded with the hot metal, which forms a fin at the plane of weld. Examining these possibilities in detail, it is not probable that such deep-seated decarburization, extending with maximum effect to the very center of a 2-in. round bar, is done by reaction with the oxygen of the air. This would postulate entrance of oxygen and egress of carbon oxides in large quantity without leaving behind traces in the form of oxides or

Jan 5, 1919

By D. Sethuram, P. G. Koppad, S. Iyengar, R. Shobha

TiB2 and CeO2 particle-reinforced Al6061 hybrid composites were manufactured using stir casting and hot rolling techniques. The base alloy and composites were hot-rolled at 500ºC and a 50% reduction was achieved through 12 passes. The effect of varying TiB2 and CeO2 particle additions on the microstructure and mechanical properties of the Al6061 matrix was studied. Scanning electron microscopy showed uniform dispersion of both the reinforcements, with good interfacial bonding. Microhardness and tensile properties like yield and tensile strength were found to be higher for hybrid composite with 2.5% TiB2 and 2.5% CeO2 compared to Al6061 alloy and other hybrid composites. The increased tensile strength is attributed to good dispersion and interfacial bonding between the particles and Al6061 matrix. Fracture analysis using a scanning electron microscope revealed ductile fracture for the Al6061 alloy and mixed characteristics of ductile-brittle fracture for hybrid composites

Oct 1, 2021

By William Reininger

Microtunneling provides a necessary solution for multiple utility crossings associated with the New York Metropolitan Transportation Authority Capital Construction Company?s (MTACC) Eastside Access Project for the Long Island Rail Road. Construction of four TBM tunnels and their approach structures at the eastern end of the project in Sunnyside, Queens required significant modification and expansion of the railroad infrastructure at this location. Maintenance of railroad traffic during project construction is a principal requirement. As a consequence fourteen (14) utility crossing segments are being installed under active traffic by microtunneling methods. Microtunnels were installed in a variety of conditions including depths, types of soils and construction restraints.

By G Akdogan, R V. R Handfield-Jones

The application of microwave energy as a substitute for conventional heating has drawn interest from many researchers in extractive metallurgy. Microwaves have a heating effect just as many other forms of radiant energy. Microwaves are able to penetrate the substance at which they are directed and in being absorbed heat the material from the inside. As a result of heat generated in the interior of a particle, microwaves can affect the rupture of a particle (in this case a host ore) and break down the matrix of the particle (host ore) and expose the recoverable mineral to the leaching reagent. Two series of leaching experiments were carried out at temperatures above 90????C using a conventional heater (hot plate) and a modified 850 W, 2.45 Ghz microwave oven. One series of tests was carried out at ambient temperature. A pyritic/arsenopyritic gold concentrate was leached with 3.3 kg/t to 6.8 kg/t NaCN for two hours. The extraction of gold at 6.8 kg/t NaCN was higher in microwave assisted leaching (59 per cent) than the extraction obtained in leaching at conventional heating (39 per cent) and ambient temperature (28 per cent). Extraction of gold was dependent on the size fraction used and was 48 per cent for û75 ¦m, 43 per cent for û90+75 ¦m and 37 per cent for û150 + 90 ¦m size ranges.

Jan 1, 2000