Search Documents

By Walter I. Enderlin

To economically extract ore from great depths in the earth while sustaining an acceptable working environment will require the development of new technology and equipment, involving large capital expenditures. Moreover, careful analysis and advance planning will be required. But, the literature is lacking in data pertaining; to the thermal properties of various host rocks and to quantities of heat generated by various underground heat sources. This types, of data is required to forecast nine heat loads during advanced planning and design. This thesis sets forth a practical method for evaluating underground sources of heat in deep mines and provides an improved information base. Moreover, seven topics for further research are recommended. The heat sources considered are: wall-rock, ground water, adiabatic compression, equipment, service lines, blasting, metabolism, curing of cement, and oxidation of sulfides and timber. Seven deep metal mines with high production rates and high heat loads were visited to obtain data necessary to assess their thermal environments. Mine records were examined, wall-roc:, temperatures were measured and a survey of the mine ventilating air and mine drainage was performed. Also, the thermal conductivity of wet and dry specimens of the host rock were measured in the laboratory. Data analysis disclosed that rock heat and adiabatic compression account for stout 60 per cent of the mine heat load at depth. Equipment currently contributes approximately 20 per cent; however, to offset increasing costs with depth, increased mechanization is anticipated. The treat from ground water averages 19 per cent and the contribution from blasting, metabolism and cement is negligible. Also, approximately [0] per cent of the increase in the enthalpy of the ventilation air is in the form of latent heat. Moisture, however, did not significantly affect the thermal conductivity of the rock specimens measured in the laboratory. Also, from the data, it is evident that a negative correlation exists between the thermal conductivity of the host rocks and the per cent of the heat load derived from the wail-rock. Furthemore, steady state heat flow renditions may be assumed in airways where there has been no major changes in the ventilation system for a period of two years or more. Under these conditions, the author found it more convenient and reliable to compute heat influx using the steady state equation for heat flow into a cylinder, rather than Carrier's method for transient heat flow, which is so often used.

Jan 1, 1973

By Floyd C. Bossard

Major air-cooling facilities have been installed and are operating underground in U.S. copper mines (at Butte, Montana and Superior, Arizona), South African gold mines, European coal mines, Zambian copper mines, Kolar gold mints in India, Coeur d'Alene mines of Idaho, plus other locations. Mining districts that utilize spot cooling and local air-cooling facilities would increase the above listing many times. The principal objectives of underground mine air cooling systems are to; 1. Extract heat and water vapor from the mine air and provide for their removal from the mine via (a) water pumped to surface or (b) discharged mine exhaust air. 2. Provide acceptable artificial ambient conditions for efficient working mine development and production areas. 3. Recondition used air, thus supplementing the limited mine ventilation balance. In deep South African gold mines, when rock temperatures exceed about 105°F, cooling of underground air becomes necessary for the poorly ventilated sections of the mine. By U.S. standards, air conditioning in poorly ventilated mines usually commences when the virgin rock temperature exceeds 100°F. On the other hand, well ventilated deep vein-type mines in the U.S. have been able to forego general cooling of mine air until the mines have been extended to such depths that the virgin wallrock temperatures have exceeded 115° - 120°F. It must be noted that spot-cooling of selected development headings may be required in many mines where rock temperatures exceed 100°F. Such local air-cooling practices permit the driving of long headings for exploration or extended development prior to holings which result in establishment of primary ventilation circuitry. The following summary reports on current practices of cooling and dehumidifying mine air. General system descriptions with important details will hopefully permit the reader to gain an understanding of the subject. A list of references is provided for this serious investigator who desires a more thorough knowledge-base and who is responsible for the design of a mine air-cooling system.

Jan 1, 1973

By Paul L. Michael

Roof warring signals from eleven underground coal mines (principally in the Pittsburgh seam) were studied and analyzed. The character of individual acoustic warning signals is shown to be dependent on spectral distribution of energy. Reverberation tires (pulse decay rates) were found to be usually between 0.1 and 0.5 seconds. Listening tests were conducted to assess the miner's ability to discriminate speech and roof talk signals in noise and in quiet, with and without ear protectors and with various levels of hearing loss. The ability to detect roof talk is shown to be generally degraded while wearing car protection in quiet, although, if car protectors are worn only when required by high noise levels, the ability to detect roof talk will be preserved at its maximum.

Jan 1, 1972

By Peter G. Groer

The commonly used exact methods (1-2) to determine the WL measure the total a activity or the total number of a counts during three preselected time periods. Due to the half-lives involved (TRaB = 26.8 min, TRaC = 19.7) I these methods take 3S minutes to complete the a activity Ra measurements. Methods using the total a counts, obtained at times less than about one RaB half-life after the end of sampling run into statistical 214 problems. These methods are almost blind to RaB (Pb214) as a consequence of its relatively long half period (see above) and the fact that RaB is a ß emitter. The way out of this dilema is to measure RaB directly through its ß activity. Since RaB's daughter Rae (Bi214) is also a ß emitter, the two f3 spectra have to be separated to obtain RaB alone. How this is accomplished 1s described in subsequent sections describing the theory of the IWLM and its calibration. 2.0 THEORY The IWLM samples air for two minutes and counts this airs ample for two minutes starting 3 sec after the end of the sampling period. The instrument has three channels. The lower a channel, the upper a channel, and one ß channel. The total RaA counts observed are accumulated in the lower a channel, the total RaC? counts are stored in the upper a channel. The total ß counts from RaB and RaC are recorded in the ß channel. These three quantities are functions of NA, NB, and NC, the unknown concentrations

Jan 1, 1975

By Klaus L. Cappel

In 1972, the Bureau of Mines of the U. S. Department of the Interior commissioned the development and design of a Simulator for research and testing of mine roof supports used in long-wall mining. The purpose of the Simulator is to reproduce forces and displacements of a section of a mine roof in contact with one or more supports. This report is an account of the design process that resulted in the final configuration of the Simulator presented here. It includes discussions of engineering considerations that led to major changes in important details of the Simulator. These changes, however, did not substantially alter the basic design originally proposed, except for the elimination of certain originally-specified features that were adjudged as insufficiently cost-effective by both the Bureau of Mines and the design agent at an intermediate stage of the design.

Jan 1, 1974

By K. J. Bathe

The current version of the computer program ADINA/BM (Automatic Dynamic Incremental Nonlinear Analysis for the Bureau of Mines) for linear and nonlinear, static and dynamic finite element analysis of mine structures is described. The complete report is divided into four parts. In Part A the program solution capabilities, the finite element library, the logical construction of the program and storage allocations are discussed. In Part B the theory and numerical techniques used in the program are summarized. In Part C brief problem descriptions and solution results for some sample solutions that have been transmitted as data cases with the program are presented. In the last section of the report, Part D, the users? manual of the program is presented. Program ADINA/BM is a general effective tool for coal mine structural analysis. The program is an extension of the computer program NON SAP (which was developed under an earlier contract with the U.S. Bureau of Mines). The important additional capabilities of ADINA/BM are: (1) the occurrence of all elements is time dependent, (2) all elements can be used in geometric and material nonlinear analysis, (3) the truss element can be used in elastic-plastic analysis, (4) the three-dimensional element can be employed in orthotropic, elastic-plastic and cracking and crushing analysis, (5) the program executes an out-of-core solution and thus allows the analysis of very large and complex coal mine models, (6) the truss elements can be employed as 2-4 variable-number-nodes elements, (7) a rock material model has been implemented, (8) displacement constraint equations can be imposed in the solution, (9) more flexibility in specifying the incremental solution strategy and an acceleration procedure in the equilibrium iteration are available

Jan 1, 1978

By Marilyn Biviano

(l)The direct economic costs to this nation resulting from a decision to embargo South African strategic and critical minerals imports are estimated at $1.85 billion per year.2,3 About 94 percent of these estimated costs are for two platinum-group metals (PGM's), platinum and rhodium. The estimated costs of a 5-year embargo beginning in 1988 for the strategic and critical minerals analyzed are presented in Table 1.4 (2)There are sufficient alternative world sources to South Africa for manganese, chromium, palladium, titanium, and vanadium to meet U.S. industrial demand in the event of an embargo. (3)Alternative world sources to South Africa for platinum and rhodium cannot meet U.S. industrial demand. Non-South African world supply sources can meet about 40 percent of domestic platinum consumption requirements and 50 percent of rhodium requirements. (4)As a result of the increase in prices for platinum and rhodium during the embargo, expansion of domestic platinum-group metals mining and secondary production is expected. During a five year embargo, domestic primary and secondary production expand and together satisfy about one-third of U.S. platinum requirements, one-third of U.S. rhodium requirements, and over one-half of domestic palladium requirements.

Jan 1, 1988

By Stan Henning

The monthly summary of the climatological record for the demonstration mine is presented in Table 1. Tear normal temperatures occurred throughout the growing season. From May to October precipitation was more than normal except in June when it was 2.55 inches below normal. Corn and soybean plantings were delayed until June 2-7 because of wet field conditions. This is about one month later than normal for corn planting. Insect infestations were much less than those encountered in previous years. Cutworm activity was not noticed and alfalfa weevil infestation were small and patchy. Stalk rot in corn was a significant problem at harvest and resulted in much Milk lodging. The wet and generally overcast conditions of July, August and September were bend 10 beneficial al to certain plant disease organisms. For example, pumpkins planted in a small garden area at the demonstration mine did not ripen because of a powdery mildew resulting from overcast, wet conditions. Field operations and row crop plantings were greatly delayed by wet field conditions. It was difficult to plant by conventional tillage because the soil remained soft and sticky where the moldboard plow had been used. Plots in the no-tillage system could he planted before conventionally tilled plots could be traversed. Plant emergence and plant density at

Jan 1, 1982

By Fred E. Fiedler

A demonstration project investigated the feasibility and effectiveness of two management interventions, Management Training and Organization Development, for improving productivity and safety in metal/non-metal mines. The management training intervention was conducted at Texasgulf Company's trona mine, using three nearby trona mines as controls. The Organization Development intervention took place in Hecla Mining Company's Lucky Friday mine, using the highly similar Star Mine as control. The two management interventions seemed about equally effective in reducing accidents and injuries, as well as MSHA citations, and the management intervention at the Texasgulf mine also appeared to have led to substantial improvement in mine productivity.

Jan 1, 1983

By James L. Hendrix

The applicability of a rotating drum with an attached trommel as a flocculation dewatering device of Florida phosphatic claywastes was studied. Several experiments were conducted in order to determine the important fabrication and operating parameters. Results from the experiments indicated flint the dosage of polyethylene oxide required to form a satisfactory product cake could be reduced by using the rotary drum, which introduces less shear stress into the fluid than a constant stirred tank mixer. It was found that the length of the mixer was the most important parameter. Increased length increased the retention time the flocs stayed in the mixer without dewatering. Such increased time decreased the stability of the flocs. Through analysis of residence time distribution data it was found that the longer mixers approached plug flow characteristics. Other important parameters were trommel length and rotational speed. Mixers from 10 cm diameter to 35.6 cm diameter were tested with good results.

Jan 1, 1982

By P. M. Daling

This report, sponsored by the U.S. Bureau of mines, presents the results of an examination of available safety assessment methods and their applicability to the mining industry. Standard safety analysis procedures were evaluated for relevance to the mining industry and mire operators' needs. The major safety concerns and needs of mine operators were identified through telephone contacts and a visit to a mine site. Safety assessment methods recommended for use by the mining Industry were also investigated for potential adaptability to a user-interactive computer system. Several methods were determined to be Immediately transferrable to the mining industry; these techniques are described in a user's handbook produced as part of this project. The handbook gives detailed instructions on appropriate application and utilization of these methods. Other techniques will require further development before they can be effectively transferred to the mining Industry. These methods, their advantages, disadvantages and resource requirements are described in the final project report. Recommended system safety analysis techniques facilitate an evaluation of total mine system safety and a determination of safety-related interactions among systems within a mine. The application of these methods to the mining industry could result In reductions in both the frequency and the consequences of mine accidents.

Jan 1, 1983

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of available safety assessment methods and their applicability to the mining industry. Standard safety analysis procedures were evaluated for relevance to the mining industry and mine operators' needs. The major safety concerns and needs of mine operators were identified through telephone contacts and a visit to a mine site. Safety assessment methods recommended for use by the mining Industry were also Investigated for potential adaptability to a user-interactive computer system. Several methods were determined to be immediately transferrable to the mining industry; these techniques are described in a user's handbook produced as part of this project. The handbook gives detailed instructions on appropriate application and utilization of these methods. Other techniques will require further development before they can be effectively transferred to the mining industry. These methods, their advantages, disadvantages and resource requirements are described in the final project report. Recommended system safety analysis techniques facilitate an evaluation of total mine system safety and a determination of safety-related interactions among systems within a mine. The application of these methods to the mining industry could result in reductions in both the frequency and the consequences of mine accidents.

Jan 1, 1983

By Corale L. Brierley

Beneficiation of phosphate in the southeastern United States generates a slurry of finely divided clay. These clay-wastes are impounded to allow the particulates to settle. The aggregation of phosphatic clay-slime wastes and slimes produced from potash beneficiation by microbial processes was studied using several bacterial species known to produce polymeric substances. Experiments included flocculation capacity of clay-slimes by whole cells, the determination of respiratory activity of whole culls in the presence of phosphatic clays, observation of clay flocculation rates by polymers derived from these organisms, and clarity of polymer-flocculated clay suspensions. The polymer-producing organisms exhibited little capacity for flocculating phosphate and potash clay-slimes. Fungal spores of Cladosporium cladosporioides (isolated from a phosphate clay-waste impoundment), when agitated with clay-slime for several days, caused the clay to form pellets. Separation of the clay/fungal pellets (density 1.1 g ml-1) from the process water might he possible using a screening technique. Studies with C. cladosporioides included the determination of suitable energy substrates and supplements for growth, absorption studies of a pigment produced by the organism, determination of the time required for bioflocculant production by the organism, and an elucidation of the conditions required for the pelletization of clay-slimes by the fungus.

Jan 1, 1982

By J. Cseff

A variety of shaft and hoist equipment exists in the United States. Nearly all hoist systems are electrically driven. Machine elements which comprise the hoists and ancilliary equipment include bearings, shafting, drums, gear reducers, couplings, brakes, clutches, sheaves and electrical motors. Volume I, Systems Description, describes the various components encountered in most mine hoist and shaft installations, and brief descriptions of functions and constructions. Hoist ropes and balance ropes are specifically excluded from this report. Associated with the hoisting system is the headgear, shaft and equipment, loading/dumping facilities and the actual conveyances and their rope attachments. Volume II, Inspection and Maintenance Procedures, discusses scheduled Inspection and preventative maintenance in general terms. Preventive scheduled inspection and maintenance procedures assist in the smooth operation of mine hoisting plant, by the prevention of unscheduled or catastrophic equipment failure and its attendant downtime. Schedules and overall maintenance planning is required at the management level. Records and equipment logs must record inspection and maintenance, and unusual operations or incidents. A cross reference between MSHA regulations and various equipment components is included as part of the report. A discussion of the various non-destructive testing methods which may be applied to hoisting equipment is also included.

Jan 1, 1981

The investigation summarized in this report addressed two primary issues: the determination and use of correction factors, and the development of guidelines for velocity measurement site selection. Other ancillary issues which were addressed include a comparison of measurement methods and devices, aircourse cross-sectional area measurement, and characteristics of mine airways. An exhaustive literature search and analysis was performed; extensive in-mine experiments were conducted; a quantitative analysis of the data was used to develop correction factor tables and site selection guidelines. The reported results of other researchers who have examined the correction factors and site selection criteria, were analyzed in light of the results of this study. The measurement devices included in the experimental phase were: vane anemometer, vortex shedding anemometer, a prototype thermoanemometer, smoke tube, and, oil of wintergreen. The measurement methods include single-point centerline, timed¬-point traverse, continuous traverse for the anemometers, and various distances and cloud positions for the smoke tube and oil of wintergreen devices.

Jan 1, 1983

By P. J. Remington

Field measurements utilizing a seat pad accelerometer were made on 25 underground coal mining machines in order to quantify the vibration levels experienced by the operators. Those data were combined with information on the statistics of the operating times of those machines in order to compare the operator's vibration exposure to the criteria in ISO 2631, "A Guide for the Evaluation of Human Exposure to Whole Body vibration." The comparison showed that about 30% to 40" of all underground coal mining machine operators can be expected to be exposed to vibration exceeding the fatigue decreased proficiency criterion, whereas only 10 to 15% would be expected to experience vibration exceeding the exposure limit. The primary sources of the exposure are shuttle cars and possibly scoop trams. Detailed exposure statistics are presented and the implications of the results are discussed.

Jan 1, 1983

By R. R. Faddick

A mineral slurry data hank has been compiled, containing slurry pipelining data on sixteen ores, concentrates, and tailings. The data bank it in the form of a computer print-out all they necessary system constants and headloss data for each mineral commodity. The purpose of the data bank was to assist in the development of a universal head loss correlation for mineral slurries, if such a thing exists. Present headloss correlations were tested and found to be inconsistent for the various mineral slurries. Consequently, a different approach was taken, that of compiling a library or Stanton diagrams relating friction factor and Reynolds numbers for a given slurry in a given pipe diameter. The advantages of the diagrams arc demonstrated and discussed. While this correlation shows excellent potential, it is necessary that additional work, both theoretical and experimental, be performed. In addition, two equations are given from which a design velocity may be obtained to minimize deposition or formation of bedload. The equations are based on data taken from the mineral slurry data bank.

Jan 1, 1972

By A. Brown

This report details work performed and results obtained in a study of the water management aspects of oil shale mining and retorting in the Piceance Creek Basin. Three specific sites were investigated, and optimal water management systems for both conventional and in-situ extraction processes were generated. Water-related legal and environmental constraints on development were identified and the water management schemes were developed in compliance with these regulations. Limitations on shale oil production implied by limited water supplies were evaluated. Potential Basin-wide effects of development were evaluated using a computer model, and mitigation strategies were developed. Recommendations for additional investigation and analyses were presented.

Jan 1, 1977

The purpose of this study is to develop designs to facilitate and accelerate auger rotation stoppage (and auger rotation start up so as to promote auger disengagement during auger miner repositioning) and to provide a time delay and warning signal prior to auger start up to permit any miner s near the augers to get away from the augers before they start rotating. In the underground coal mines in the U.S., there are four auger miners that are currently in use. They are the Jeffrey 100L (see Figure 1-1) and 100M (see Figure 1-2), and the Wilcox WCM and the MK20A (see Figure 1-3).

Jan 1, 1974

By Damon C. Gray

This report contains a recommended program of acoustic research to be conducted by the U. S. Bureau of Mines. The program is directed toward the abatement and control of machinery noise in underground coal mining operations. The study conclusions and specific problem areas which led to the definition of the recommended program are also briefly described.

Jan 1, 1971