Search Documents

By A. Gronningsater

Introduction As is well known, the fight between the blast furnace and the reverberatory furnace in copper smelting during the second decade of the century ended with a victory for the latter, a result which must largely be attributed to the introduction of flotation methods. To my knowledge, no new blast furnace has been blown-in at any American copper smelter since the War. As the metallurgy of nickel, up to and including matte smelting, is generally considered a close parallel to that of copper, the introduction of reverberatory smelting in the big new smelter of the International Nickel Company at Copper Cliff, built in 1928-30, seemed a logical adherence to a well established trend. In view of these facts, considerable comment was made when Falconbridge Nickel Mines decided to retain the blast furnace in their smelter built about the same time, in 1929. A presentation of the reasons governing this choice should therefore be of interest. The basic principles underlying the Falconbridge practice, and the considerations guiding the successive steps in the operations, will be discussed in the following. To understand the problems involved, the character and mode of occurrence of Sudbury ore must be kept in mind. Large amounts of disseminated ore are generally present. Although the gangue usually runs only about 50 per cent Si02, the ore hoisted as a rule contains more silica than needed in the smelting operation; until recently this excess was removed entirely by hand picking (in later years supplemented by magnetic sorting methods), a difficult and not very satisfactory method, in which 'the border line between ore and waste is entirely arbitrary, and therefore too much depends on the judgment of the picker.

Jan 1, 1934

THE CHAIRMAN (A. F. Lucas, Washington, D. C.).-Mr. Matteson has stated that the drilling of certain deep wells has proved a failure because they were abandoned too soon. He advises drilling more wells around salt domes, in the hope of finding additional oil sands. I have had some experience on the domes and believe that by drilling shallow wells, one loses time and money. I have advanced the opinion -that by drilling central wells in the -most likely location of a dome, showing is certain weakness, a better result could be obtained. I have in mind one locality where Mr. Knapp drilled a well through the salt¬the only location that I know of on the Gulf Coast where oil was found underneath the salt. Mr. Knapp found a great deal of gas in it. The salt itself was impregnated with oil and gas; and my opinion is that in such instances, instead of drilling so many wells around a dome, if you will attack at a weak point to as great a depth as a drill will go, the results will he much better. At present we have instances where drills have penetrated to 7300 or 7400 ft. in depth. Why couldn't the rich companies that are operating around the Gulf Coast arrange to get some special drilling apparatus and drill with the rotary first for, say, 3000 to 4000 ft., always in the likely location, and then proceed with the cable? I think we need just such work. In Mr. Matteson's paper lie quotes from an author whose writings in the Federal Bulletin and in the Louisiana Bulletins have been quite extensive. He states that oil and asphalt have originally been found on the surface of those domes. I have been over and examined nearly all of those domes (not all of them, because many have been developed in the last few years) and found no such occurrence at the time; and in the old well-known humps or big hills, as they generally called them; I have never found either salines or asphalt or petroleum. In only' one instance it looked as though asphalt night have exuded out of the ground, and that was in the Sour Lake, but right in that neighborhood years previous to that a company had operated commercially-they had a little refinery there-and had found it so unprofitable that they pulled up stakes and quit.

Jan 4, 1918

By Charles M. Wilk

"Solidification/stabilization (S/S) treatment is used to treat hazardous wastes for disposal and in the remediation/site restoration of contaminated land . SIS is also an increasingly popular technology for Brownfield (industrial property) redevelopment, since treated wastes can often be left on-site and to improve the soil for subsequent construction. This paper discusses the applicability of the technology to various wastes, basic cement chemistry relating to SIS, tests used to design treatability studies and to verify treatment, basics on implementation of the technology in the field , and examples of SIS use at brownfield sites, including a former wood preserving site, former manufactured gas plant sites, a former electric generating station, and a shopping mall development.INTRODUCTIONSolidification/Stabilization (S/S) is a widely used treatment for the management/disposal of a broad range of contaminated media and wastes; particularly those contaminated with substances classified as hazardous in the United States. The treatment involves mixing a binding reagent into the contaminated media or waste. The treatment protects human health and the environment by immobilizing contaminants within the treated material. Immobilization within the treated material prevents migration of the contaminants to human, animal and plant receptors. SIS treatment has been used to treat radioactive wastes since the 1950s and hazardous waste since the 1970's (Conner 1990). SIS continues as a cornerstone treatment technology for the management of radioactive waste, hazardous waste, and site remediation and Brownfield redevelopment."

Jan 1, 2005

By D. S. Dihalu

A generalization of Gy?s model for the fundamental sampling error introduced the new ?parameter for the dependent selection of particles?, denoted as Cij. This allows for modeling deviations from the ideal situation where the selection of a pair of particles is composed of two independent selections. The generalized model potentially leads to more accurate variance estimates in the case of clustering of particles, differences in densities or sizes of the particles or repulsive inter-particle forces. A straightforward and practically applicable method is needed for the determination of this parameter for miscellaneous mixtures in industrial settings. In this contribution, the feasibility of using digital image analysis to determine this parameter Cij, will be demonstrated. Line transect sampling of a digital image was used to construct a transition probability matrix. A new algorithm to derive quantitative estimates for Cij will be presented and discussed. The applicability was verified by a photograph of zirconium silicate particles of sizes typical for industries dealing with pharmaceutical, food/feed, and environmental applications. Conditions affecting the practical applicability are identified and potential pitfalls will be discussed, including e.g. how a potential unrepresentative surface can affect the quality of the estimate of Cij.

Jan 1, 2010

By Robert M. Dreyer

The first time that a geologist is confronted with the necessity of evaluating a lateritic ore deposit, he may feel that nothing could be easier. Why should there be any problems in making an economic evaluation of a relatively flat-lying, surficial ore body? After several hundred thousand dollars worth of frustrating work often culminating in a series of non-reproducible data - the evaluator may be a sadder and wiser man. This paper will try to illustrate why the evaluation of lateritic bauxite and nickel deposits is among the most difficult problems confronting an economic geologist - and, more especially, how this problem can be solved. Volumes have been published on descriptive and genetic studies of lateritic ores. Obviously, there is time today only for the briefest description of such an ore body. The laterite is a soil formed under tropical conditions and resulting in the concentration, within the soil zone, of certain tri-valent metals.- especially, aluminum and nickel. The soil zone is divided into two parts: (a) the true soil or lateritic zone and (b) the zone of, partially altered bed rock or saprolite. It is important to remember that, whereas bauxite generally is confined to the laterite zone, nickel deposits occur in both the laterite and

Jan 1, 1977

By Ian Wark

IN an earlier paper1 measurements of contact angles due to the effect of xanthates on mineral surfaces were reported. The solutions in which these measurements were made differed widely from those of modern flotation circuits. It is intended, however, by introducing, one at a time, the other principal reagents of flotation, to approach gradually the solu-tion composition of flotation liquors. The work now described is an attempt to determine the effect of one of the most important of these reagents-namely, sodium cyanide-on the establishment of air-mineral contact. The work has been carried out for the following companies: Broken Hill South, North Broken Hill, Zinc Corporation, Electro-lytic Zinc of Australasia, Mount Lyell Mining and Railway, and Burma Corporation. Since the effect of cyanide is inseparably connected with the alkalinity, the results cited below deal with the mutual effects of alkalis and cyanide. Alkalis alone exert a significant effect on the air-mineral contact but comparatively large amounts are required. Since the addition of a small amount of cyanide greatly decreases the degree of alkalinity necessary for the suppression of contact at surfaces of any of the minerals experimented with (except galena) and since alkalis are rarely used alone in practice, little attention has been paid to cyanide-free solutions. It was shown in the previous paper that, excluding the dixanthogen effect, whenever contact was practicable at all in an ethyl xanthate solution the angle of contact was 60°. There is, therefore, less necessity to measure equilibrium contact angles; in fact, the experiments herein described have generally been conducted with a view to determining whether contact is possible and not to measuring the actual value of the contact angle. The separations which have generally to be effected in dealing with complex sulfide ores are: (1) galena from sphalerite, pyrite, etc.; (2) sphalerite from pyrite and/or gangue minerals; (3) copper minerals from pyrite and gangue minerals; (4) pyrite from gangue minerals; (5) chal-

Jan 1, 1933

By Andrew W. Jenike

There used to be a time when bins were designed for total volume and placed in any available place of the plant. Poke holes were provided and feed was maintained by manual prodding, lancing, hammering, and by various mechanical flow-profiting devices. Little thought was given to what occurred inside the bins and why materials did not flow. Indeed, such mental effort was hard to justify while low-cost manual labor was plentiful, quality standards low, and rates of feed moderate. The past fifteen years have seen a drastic change in these conditions. We all know that labor for hard manual work is becoming unavailable at any wage, level. Standards of product uniformity are continuously rising. This uniformity is just as important in a fine ore feed to ball mills as it is in a cattle feed or in a flour mix. Rates of feed now frequently exceed 2,000 tons per hour per feeder. At that rate there is no time for, lancing or prodding. An efficient storage, plant contains a known available volume of bulk solid, and feeds it at the required time, at the prescribed rate, and without degradation of the product. A storage bin may also perform other functions such as blending of different grades, degasification of aerated, powders, isolation of different gaseous media. A contact bed of particles flowing by gravity in counter-current with a gas or liquid may be used as a continuous reactor. Gas or liquid pressures can be simply contained by, a sufficient head of flowing solid.

Jan 1, 1968

By Dan Miners

"This presentation will provide an overview and understanding of Mine Safety and Health Administration (MSHA) and Ontario Regulations for Mines and Mining Plants. It includes discussions on the history and practical development of the standards and an overview of engineering best practices from a construction, maintenance and operational viewpoint. INTRODUCTION Ontario is one of the safest mining jurisdictions in the world and has some of the most comprehensive regulations for the construction, operation and maintenance of a mine. In the USA, several operators have adopted some or all of the practices prescribed by the Ontario Regulations as an internal procedure. Experience has demonstrated that these plants are indicating less unplanned downtime and fewer issues with MSHA inspectors in their hoist plants. HISTORY AND THE REGULATIONS Both Canada and the USA have had some form of laws governing the operation of mines since the late 1890s. The paths of legislation have run in reasonably parallel lines, continually improving the health and safety conditions in the mining industry. Ontario Mine Health and Safety In the 1970s the accident rates in mining were higher than any other industrial sector; this prompted a Royal Commission on the Health and Safety of Workers in Mines (the Ham Report). The recommendations of this report, published in 1976, generated several changes in the regulations regarding worker safety in mines. Following the release of the Ham report, the Occupational Health and Safety Act (OHS) was passed by the Legislature in 1978. The Act is a set of comprehensive laws governing almost all Ontario workplaces, and it replaced separate laws governing different industrial sectors. OHS is enforced by the Ministry of Labour (MOL), and this discussion will focus specifically on Ontario’s Occupational Health and Safety Act, R.R.O. 1990, Regulation 854, Mines and Mining Plants, Part X Mine Hoisting Plant (Ontario Regulations). USA Mine Health and Safety A coal mine explosion in West Virginia and medical studies on occupational disease led to the 1969 Federal Coal Mine Health and Safety Act (Coal Act). The Coal Act was the most comprehensive and stringent Federal legislation governing the mining industry to date. The Mining Enforcement and Safety Administration (MESA) was formed, following the 1973 Act, as a new departmental agency to assume the enforcement of safety and health in mines. The Federal Mine Safety and Health Act of 1977 (Mine Act) transferred enforcement responsibilities from the Department of the Interior to the Department of Labor and named the new agency the Mine Safety and Health Administration (MSHA). This agency enforces the Code of Federal Regulations (CFR), and this discussion refers to CFR Title 30 Mineral Resources, Chapter I Mine Safety and Health Administration, Department of Labor, Subchapter K—Metal and Non-metal Mine Safety and Health (MSHA)."

Jan 1, 2019

By N. J. Themelis

The basic chemical, thermal and transport principles that underlie sulfide smelting of. copper, nickel and lead are reviewed. Two basic types of modern smelting processes are distinguished?: flash-smelting, where the predominant reactions occur between oxygen-bearing gas and concentrate particles dispersed therein; and bath-smelting where the concentrate is enveloped and reacted in a turbulent bath of matte, slag and gas. The controlling heat and mass transfer phenomena are discussed, and appropriate correlations are proposed.

Jan 1, 1983

Coal mining in New Zealand is principally a State-owned and controlled operation where the State produces 70 per cent of the coal in New Zealand and 65 per cent of coal mined in the Waikato. The State's flexibility in production quality and price makes them tough competition. Coal in the Waikato varies in quality considerably throughout the region making the high quality coal deposits as in the Huntly district a highly sought after commodity. The high quality of coal is often offset against transport costs as, for example, Maramarua coals can compete effectively in the Auckland market and dollar per calorific value basis.

Jan 1, 1984

By G. H. K. Schenck

Weather changes of a daily, weekly, or seasonal period affect mineral production and cause significant losses that are considered unavoidable. Private weather forecasting services are available on a contract basis that can significantly reduce the uncertainty associated with weather-induced changes in the production of and demand for minerals. This paper provides examples of current practice and reviews the opportunities that await those producers who incorporate weather services as an integral part of their operating, scheduling, and planning procedures. Private weather forecasts can be highly accurate because atmospheric trends such as conditions and movement tend to persist and are related to previous meteorological events. Commercial meteorological services are prepared to deal specifically with a mineral producer's special problems (Table 1). Tactical use of private forecasts is a major advance over the severely restricted value of public forecasts which, of necessity, are general in nature and cover a dispersed geographic territory. Private weather services provided on a consulting fee basis offer the mineral producer the opportunity for tactical and strategic response to weather conditions at an acceptable cost. This contrasts with the too-frequent current tendency to view weather as a random variable the costs of which are unknown and about which nothing can be done.

Jan 1, 1970

THE Directors of the Institute at the May meeting voted to take a referendum of our members on the subject of licensing engineers. At the June meeting, this action was rescinded, it being felt that the proportion of the members of this Society who would respond to such a referendum at the present time would not be large enough to give the data for which the referendum was intended. It was deemed advisable in its place to publish in this issue of Mining and Metallurgy arguments in favor of and against licensing. Two arguments by proponents of the movement follow. Many articles against licensing have appeared in these columns, in the last two years, covering most of the arguments on the negative side so that the sole contribution herewith is a summary of a referendum taken by the Mining and Metallurgical Society in 1920-21.-EDITOR.

Jan 7, 1923

By Ray Brainard

The Jollyville Transmission Main will be a 10.5-km- (6.5-mile)-long, 213-cm (84-in.) diameter rock tunnel. The tunnel will pass beneath the Balcones Canyonlands Preserve, which was established to protect two endangered bird species, six endangered cave invertebrates and a threatened salamander. To address the sensitive habitat that the transmission main is to pass through, the city of Austin developed an environmental commissioning (EC) process that brought together environmental engineers and scientists, the city?s project management team and the designer team to work collaboratively to meet the city?s goals of producing a cost-effective design while also protecting the environment. This paper describes the environmental commissioning process and the benefits it brought to the project and environment through some unique environmental mitigation measures to protect this sensitive area.

Jan 1, 2012

A series of gas inrush events occurred during development at Grosvenor mine resulting in exposure to elevated levels of methane at the production face. A total of 22 gas inrush events occurred releasing between 15 and 130 m3 of methane during each event. The presence of an undrained seam in the immediate floor, geotechnical characteristics of the floor, and the stress environment all contributed to these dynamic floor events, while the geological characteristics of the seam below, such as the seam thickness and ash content of 75%, prevented effective pre-drainage. However, events only occurred in headings mined parallel to the principal horizontal stress direction. In cut-throughs (C/Ts) perpendicular to the principal stress direction, no events occurred, and higher methane levels were observed at the production face.

Jan 7, 2020

The traditional measure of Lost Time Injury Frequency Rate (LTIFR) as a measure of improvement in safety performance is recognised as inadequate and misleading, lulling managers into believing that safety is improving. It is a reactive measure, and steadily declining LTIFRs around the world have failed to be accompanied by a similar reduction in the fatality rate. This paper confronts the industry with the attitudes of some mining managers, such as one that allowed fatalities to occur in the case of a gold mining company at a rate of one death per 150 000 ounces of gold produced while claiming their safety record has improved, as shown by a falling LTIFR, and viewing fatality reductions as a long-term goal instead of an immediate priority. A quantum shift in management attitudes is required to focus on proactive measurements to detect the indicators of an impending disaster, and to predict conditions conducive to fatalities. Corporate CEOs are challenged to attend the funerals of all workers killed in the workplace. CEOs who fail to attend such funerals send a message to employees that the CEOÆs priorities lie elsewhere, and that profits take priority over workersÆ lives. The dichotomy of whether mining companies are run for the benefit of shareholders or whether companies owe social responsibility to the community is examined. The role of individual responsibility for personal safety is examined, together with the psychology of employees in the mining industry. A number of proactive measurable indicators are suggested to stimulate discussion on developing robust measuring tools to predict and therefore prevent fatalities.

Jan 1, 2003

By T. R. Ley

"INTRODUCTION Brutally honest mining executives will tell you that “safety is job #1 but.. dollars are also extremely important”. When economic times are tough, as they are now in mining, it can feel like you need to choose between safety and cost control. Leading edge companies know that it is excellence at both that provides the best performance. FLUID POWER SYSTEMS Fluid power systems are ubiquitous in mining – longwall systems, continuous miners, drills, haul trucks and excavators, etc. And fluid power systems are getting more powerful and using higher pressures to move greater volumes and achieve higher productivity. Average operating pressures in mobile equipment has been rising to 450 bar (6,500 psi) over the last decade. With increased system pressure comes ever increasing levels of stored energy. Stored energy that, if released in an uncontrolled fashion, can do tremendous harm to people and things.Fluid power systems are composed of pipe, flexible hoses, pumps, valves and actuators. They are filled with fluid (mineral oil or fire-resistant) to transmit power to where it’s needed for performing work. With time and use fittings can loosen, component performance diminishes and hoses wear and tear. In hostile environments, like coal mining, hydraulic hoses can fail in as little as 2 years according to DGUV (umbrella association of German Accident Insurers), maybe sooner in some particularly challenging environments. FLUID POWER SYSTEM SAFETY While appearing simple and benign on the surface, fluid power systems, particularly such systems on mobile equipment, have many potential hazards. Hazards that most workers aren’t aware of – particularly young, new hires. And those hazards that can quickly turn deadly. During the past couple of years, including at last year’s SME Conference, I talked to a wide variety of mining people about high pressure fluid injection injuries. Some people, often with little or no field experience, never heard of it. But, people with mine operations / maintenance experience were almost always aware of such injuries.Some had even seen it happen right in front of them. But most claimed it didn’t happen all that often. It just wasn’t seen as a problem!"

Jan 1, 2016

By F. M. C. C. Vieira

There are many uncertainties that a mine designer should consider when selecting an optimal layout. Even though the inherent variability in the design parameters indicates that single-values are not representative of mining conditions, risk estimators such as ERR are often used without considering their statistical distributions. A probabilistic methodology has been developed to assess the influence of the extraction sequence and layout geometry on the rockburst risk associated with four ultra-deep mining layouts. The statistical distributions of incremental energy release rates and excess shear stresses at face elements are used as indirect estimators of rockburst risk in stopes, and the statistical distribution of the rock condition factor (RCF) is used as an indirect estimator of rockburst risk in tunnels and service excavations.

Jan 1, 2002

The modelling of lithological domains is a critical step in mineral resource and reserve evaluation. Deterministic models rely on an interpretation of the available drill hole data and expert knowledge, but do not account for the uncertainty in the spatial extent of the lithological domains. Instead, probabilistic models based on conditional simulation can be used to map the probabilities of occurrence of the domains within the deposit, which reflect the uncertainty in their presence or absence at unsampled locations. The mineral grade model is then obtained by weighting the predicted grades associated with each lithological domain by the probability of occurrence of this domain. Such an approach accounts for the continuity of the grades proper to each lithological domain and for the uncertainty in the spatial extent of these domains within the deposit. An application to a porphyry copper deposit is presented. Keywords: spatial uncertainty; plurigaussian simulation; geological control; kriging; geostatistics.

Jan 1, 2007

By W. Barnett

The Limpopo Metamorphic Belt is a complex geological terrane with at least three major deformational events. Tectonically juxtaposed lithology, open to isoclinal folding, crosscutting and re-activated shear zones and metamorphic gneisses and schists make pit slope design and maintenance a risky business. Venetia diamond mine?s Cut 3 is planned to reach 360 m by 2011. The difficult rockmass created problems in the original pit and a new more comprehensive slope design was necessary. Nearly 9 km of geotechnical drilling were undertaken to produce a new geological model and provide geotechnical information near the final Cut 3 face. All existing data from the pit were brought together into a database. SRK Consulting were brought into the project to audit the process and provide most of the manpower for the data analysis. Existing failures were back-analysed and the geotechnical domains identified. Analyses of only the southern domains are discussed in this paper. Geotechnical engineers can design slopes at any angle, but it is up to the managers at the mine to decide what risk they are willing to accept in a slope design. Once the issue of risk was discussed and settled in respect of the consequences of failure, each of the main geotechnical domains were analysed to produce a slope design at5% probability of failure with 15% above the first ramp. A risk assessment of the design was then undertaken to determine what risk the design placed on the equipment, personnel and the profitability of the overall mining operation. The risk assessment indicated minimal risk to the operation. One of the main assumptions of the final design is that the pit slopes will be dewatered. A project was immediately put in place to determine a groundwater model for the mine and to thereby determine the best dewatering procedure. However, it should be obvious that it is practically impossible to prevent benches from getting briefly saturated with water during storm conditions. It was therefore necessary to look specifically at supporting the crests of the ramps in the problematic southern domains to guard against the possibility of crest failure during heavy rains. The data available were re-analysed toward this objective. Spiles were recommended as the most cost-effective support system, and a probabilistic approach was used in the design. The final design has a 5% probability of failure, and the analyses indicate a strong sensitivity of the required spile spacing to the strength of the reinforcement material that will eventually be used. The pit slope parameters derived as per the discussion in this paper have just begun to be implemented at Venetia Mine.

Jan 1, 2001

By A. P. Whittlestone, J. D. Johnson, R. J. Pine, M. E. Rogers

standpoint. The effect on efficiency of collisions

Apr 1, 1995