Search Documents

By J. P. Gu, C. Beckermann

"Melt convection and macrosegregation in casting of a large steel ingot is numerically simulated. The simulation is based on a previously developed model for multicomponent steel solidification with melt convection, and involves the solution of fully coupled conservation equations for the transport phenomena in the liquid, mush, and solid. Heat transfer in the mold and insulation materials, as well as the formation of a shrinkage cavity at the top are taken into account. The numerical results show the evolution of the temperature, melt velocity, and species concentration fields during solidification. The predicted variation of the macrosegregation of carbon and sulfur along the vertical centerline is compared with measurements from an industrial steel ingot that was sectioned and analyzed. Although generally good agreement is obtained, the neglect of sedimentation of free equiaxed grains prevents the prediction of the zone of negative macrosegregation observed in the lower part of the ingot. It is also shown that the inclusion of the shrinkage cavity at the top is important in obtaining good agreement between the predictions and measurements.IntroductionMacrosegregation in large steel ingots is one of the most well-known and now classical problems in the field of solidification and casting [1]. Commonly found macrosegregation patterns in steel ingots are a positively segregated zone at the top, negative segregation near the bottom in the equiaxed zone, inverse segregation near the ingot surface, V-segregates along the centerline, and A-segregates in the columnar zone [2, 3]. It is well established that the macroscopic transport of species leading to macrosegregation can occur by a variety of mechanisms, including thermally and solutally driven natural convection of the melt in the mushy zone, flow due to solidification contraction, and the sedimentation of free equiaxed crystals. Fredriksson and coworkers [ 4,5] provide recent overviews of the solidification transport phenomena and macrosegregation in ingot casting."

Jan 1, 1999

By C De-Vitry

"The large Yandi channel iron deposit (CID) is located in the north-west of Western Australia and is currently mined via open pit methods. Drilling at Yandi is widely spaced and current estimates are mostly linear averages of the surrounding local samples. Linear estimates such as ordinary kriging (OK) based on block sizes that are significantly smaller than the dimensions of the drilling grid are less variable than the unknown reality (Armstrong and Champigny, 1989).Conditional simulation (CS) provides a series of plausible realisations that represent the actual grade variability at a small scale (eg 1 m + 1 m + 1 m). These simulations are very useful for a number of purposes, eg: optimising grade control, stockpiling and blending selection of optimal drill hole spacing assessing resource risk on contained tonnage and metal.At Yandi the major constituents of the ore (Fe, P2O5, SiO2, Al2O3 and LOI) are correlated to varying degrees. Independent CS of each assay variable will not reproduce these correlations. Reproducing the correlations (and the shape of scatterplots) is important if the simulations are used for the abovementioned purposes. This paper examines and compares various methods of CS that aim to reproduce the correlations between the assay variables.The CS methods evaluated in this paper are conditional co-simulation (CCS) using the linear model of co-regionalisation and two other, alternative multivariate simulation methods, which use min/max autocorrelation factors (MAF) or the stepwise conditional transform (SCT) to de-correlate assay variables before performing independent CS. It was found that CCS best reproduced the characteristics (histograms, variogram, scatterplots, etc) of the declustered drill hole data (Figure 1). Whilst simulation using MAF generally produced acceptable results, the method did not adequately reproduce the variance of the assay variables. The univariate statistics, histograms and experimental variograms were acceptable for simulations generated from the SCT. Bivariate statistics, cross-variograms and scatterplot reproduction for the SCT were unacceptable. The latter method produced inferior results because there were insufficient samples to obtain a reliable transform of the third assay variable in the transformation sequence.None of the abovementioned simulation methods provides good reproduction of all the scatterplots. This is due to the presence of clay pods, which cause some scatterplots to display two trends. These clay pods contain higher percentages of SiO2 and Al2O3 than the surrounding CID. The clay pods are generally smaller than the drill-grid dimensions. Thus their locations are typically unknown and they cannot be defined by manual interpretation, eg via wireframes. The locations of the clay pods were simulated via indicator CS. CCS was then performed separately for the clay pods and the CID. This significantly improved the reproduction of the correlation coefficients, the scatterplots and visually the simulation was more geologically realistic. Simulating the location of clay pods followed by CCS of assay variables is the recommended approach for simulation at the Yandi CID.CITATION:De-Vitry, C, 2013. Simulation of correlated assay variables - a case study from the Yandi Channel iron deposit, in Proceedings Iron Ore 2013, pp 137-148 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

The paper examines the design issues associated with the integration of mineral processing within underground mining systems. It demonstrates conceptual integrated system design options appropriate to a range of geological scenarios. Particular reference is then given to a case study of stoping in narrow base metal veins. The performance of such integrated systems in terms of productivity, economic and environmental criteria is demonstrated by means of simulation. Particular attention is given to the potential benefits to mine waste management. Processing technologies appear to offer genuine potential benefit, whilst underground mining methods may need to evolve further to facilitate full integration. This paper is based on industry supported research aimed at developing selective and clean underground mining systems.

Jan 1, 2003

By P. S. Heyns, M. Heyns

A computer model has been developed of mine hoisting systems in deep South African gold mines. Particular attention was paid to the contribution of different modelling assumptions for the guides and guide-roller assemblies. Objective functions indicative of guide-roller tyre endurance, slipper-plate forces and perceived vibration levels were introduced to quantify dynamic performance. These objective functions were used to compare models. It was found that the choice of guide and guide-roller models did not influence the forces on the guide rollers significantly for typical shaft and conveyance characteristics at typical levels of viscous damping coefficients. The rigid and finite-element guide models gave the same results as those of the effective-stiffness guide model, and while the latter is suitable for simulation for design purposes, the finite-element model should be used for unusual guide geometries

Jun 19, 1905

By G. R. Marchant, B. K. Loveday

"A mathematical model has been developed for flotation circuit simulation. This model was designed to investigate the effect of varying the circulating loads and to determine whether an improvement in overall efficiency could be gained by a size separation prior to flotation.Model parameters were obtained by regression to plant data. Highly correlated parameters in the model were combined to reduce the number of parameters so that the need for excessive data gathering was eliminated. Mass balance smoothing was used to obtain a consistent data set for regression.The results of the simulation indicate that for the same grade of concentrate, an increase in copper recovery of 0.6 per cent may be Possible by increasing the circulating loads. The results of the simulation also indicated that recleaning of the plus 200-mesh material may be beneficiaL."

Jan 1, 2014

By M. Mathey

The application of the Monte Carlo technique to production planning and everyday economic decisionmaking in mine production management is demonstrated. The logic is detailed using an example of underground production with continuous miners (CMs) and truck haulage. It is argued that availability of equipment and personnel are the predominant variables influencing mine output and productivity and that those availabilities may be well represented by binomial probability distributions. The probabilistic model is implemented in a standard Excel® spreadsheet with Palisade’s @Risk add-on to facilitate simulations. Starting from model calibration against data obtained from a mine’s annual reports, some general interdependencies of availability, utilization, productivity, and costs of production processes are outlined. Finally, several possible options and their consequences as regards production improvements are explored.

Dec 13, 2022

By A. C. Smith

Although only used in a few U.S. longwall mines, bleeder-less ventilation systems can be an effective spontaneous combustion control method in mines having a demonstrated history of spontaneous combustion. To provide insights for the optimization of bleederless ventilation systems for U.S. underground coal mines, a computational fluid dynamics (CFD) study was conducted to model the spontaneous heating in longwall gob areas using a bleederless ventilation system. A single longwall panel with a bleederless ventilation system was simulated, and typical longwall mine ventilation data were used in the simulations. The permeability and porosity profiles for the longwall gob were estimated using a geotechnical model and were used as inputs for the CFD modeling. The effects of gob permeability and resistance of the collapsed entries on the spontaneous heating were studied. The effectiveness of using nitrogen injection to prevent spontaneous heating in the gob was also examined.1

Jan 1, 2008

By J. Samir

The objective of this study is to simulate the isothermal filling up of moulds by a RTM process when adopting CV/FEM and VOF method and when also taking into account the presence of obstacles coupled to the effect of the thickness and reinforcement layers variation. The codes developed intended to ensure an optimal positioning of the injection points and of the vents and also to determine optimal injection pressures, in order to minimize the cycle times. These codes use a mesh generator proper to the team, allowing a discretization of the domain in triangular unstructured elements, with the possibility of a local refinement and inserts inclusion.

Jan 1, 2009

By J. A. L. Napier

It has been established that significant time-dependent stope convergence may occur over time periods of hours and days in certain hard-rock gold and platinum mines. The source of this time-dependent behaviour appears to be associated with both pre-existing discontinuities and with mining-induced fractures that form near the stope face. These induced fractures may be associated with blasting processes and may also be formed in response to high stress concentrations in the unmined regions immediately ahead of the stope face. In shallower platinum mining operations, time-dependent behaviour is, however, observed to be much less marked unless some form of specific mining-induced fracturing occurs. One particular case of considerable interest is the time-dependent behaviour that is found to be associated with the formation and deployment of crush pillars. The purpose of the paper is to present a simple limit-equilibrium computational model of this behaviour that is sensitive to both the formation sequence and the size of planned crush pillars in a mine layout. This model provides a useful means to optimize the sizing of crush pillars, and at the same time may be used to identify potentially hazardous circumstances in which pillars may not crush in a stable manner.

Jan 1, 2012

By Y. Q. Zhang, Y. Luo, S. S. Peng, C. T. Holland

Barrier pillars in underground coal mines could eventually be subjected to a hydraulic pressure head due to the build-up of mine water in the old workings. The pressure head could not only act as a force to destabilize the pillar but also cause seepage flow through the pillar and its surrounding strata. Excessive seepage flow could induce piping failure that in turn could accelerate the mechanical failure process of the barrier pillars. In this paper, finite element simulation approach has been employed in the evaluation of the barrier pillars. Both the stress distribution and the seepage flow pattern in and around a barrier pillar have been simulated numerically. The effects of ground stress on rock permeability to water seepage has been taken into consideration in these simulations.

Jan 1, 2001

By H Zhai, C Zhang, I Canbulat, K Yui

Sedimentary rock is a lithology that is commonly encountered in mining practices. Their properties, especially the resistance against weathering, are often of critical importance to long-term engineering stability due to their ubiquitous existence on the earth’s crust. The weathering of rocks is a complex process that involves physical degradation, chemical and biological erosions. In this study, the impact of physical weathering on four common sedimentary rocks, namely sandstone, siltstone, limestone and shale, are simulated in the laboratoryoratory environment taking into consideration the impact of preservation condition, temperature and time. In order to optimise the design of the experiment, Taguchi’s design of experiment method is implemented based on the L16 orthogonal array and selected simulation conditions. The weight and dimension variation, fracture intensity, slake durability, and uniaxial strengths of specimens are then tested to quantify the impact of weathering under various conditions. The results indicate that weathering significantly influences the strength of shale, siltstone and limestone but not sandstone. The impact of weathering on dimension variation is insignificant. For soft rocks, most physical weathering took place after second cycle of simulation, resulting in strength reduction up to 100 per cent (disintegration) but generally in a range from 28 per cent to 32 per cent. Additionally, time is the most important factor contributing to the physical weathering of weak rocks, followed by residual, preservation conditions and temperature. Last but not least, some shales, depending on the content of clay minerals, tend to develop significant fracturing or even disintegrate under the influence of weathering.

Nov 29, 2022

By Rodrigo Toro, Mario Delisle, Claudio Zamora

"The mining market is researching innovative methods to train the workforce for mining which is normally extremely difficult to get. Thus, the dynamic simulation-based technologies become an essential pillar to educate and train the inexperienced staff at the pace required by this industry. Even if Operator Training Simulator (OTS) systems are commonly used in most of industries, knowledge transmitted to operators are unfortunately not ""capitalized"" in general. The OTS systems are usually delivered as a single hardware and software platform and very little as a full service long-term.In this article, an integrated solution to increase the efficiency of the operators is proposed. This solution is based on the combination of dynamic simulation, processes knowledge, virtual reality and the knowledge capitalization through the creation of simulation scenarios and e-learning. The Codelco Ministro Hales plant simulation project for a copper concentrator plant is presented as a real life example.IntroductionDynamic and real-time process simulation have proven to be a must in the development of greenfield projects, providing mechanisms to design and test controls design, interlocks, start-up, shut down sequences and operator training, among others (see (McMillan, 2006) for further details). Early adopters of this technology were utility power plants; in the petrochemical industry have become a standard, and in the mining industry the use of dynamic simulations is growing, especially in new projects and training of operations personnel for the adoption of best practices and new technologies, see (Nikkhah & Anderson, 2001) and (Toro, Ortiz, & Yutronic, 2012).This paper outlines a solution that utilizes dynamic simulations as the base of an integrated platform for operational effectiveness, which takes into account the current scenario of new mining projects and operations, where high turn over rates and needs of specialized workforce have given a special value to this kind of technologies."

Jan 1, 2015

By A. Lebedev

Application of dynamic simulation for a base metal processing plant is discussed. The plant receives ore of variable quality from two pits and blending had to be applied to maximise recovery. The plant employs multiple stage crushing, screening, dense media separation, two-stage milling, flotation and further filtration. Stockpiles and bunkers are used in the plant to cater for breakdowns and operating delays, the latter being appropriately incorporated in the model. A detail dynamic simulation model was constructed from the rock face to the filtration plant to assist the plant design, notably with definition of the ore blending method, sizing storage capacity and in-plant conveyors. The plant model was broken down to capital equipment items and various feed types and mass balances were tested to ensure that the production target is met. The dynamic simulation tested the proposed blending method, identified bottlenecks, produced risk profiles for all strategic storage facilities and overall helped minimise the project risks and improve confidence in the plant design. Keywords: Dynamic simulation, ore grade, blending, capacity, risk profile, throughput, utilisation

Jan 1, 2020

By Verya Nasri

The use of a single tunnel boring machine (TBM) tunnel of approximately 12 to 13 m (40 ft to 43 ft) diameter for transit systems to house both light rail or subway tracks in a stacked configuration is an advanced concept that allows significant savings in construction cost and time while reducing, to a large extent, the negative effects on the environment. This solution, similar to the recently completed Barcelona Metro Line 9, integrates station platforms, train storages, crossovers, bypass tracks, ancillary areas and utility corridors inside a single tunnel. Each of the underground stations consist of a cut-and-cover entrance structure and ventilation shafts, that also serve as emergency exits. The excavations for the station structures and shafts can be done on one side of the street with nominal impact on traffic and utilities.

Jan 1, 2010

Single particle breakage tests have been used by a number of researchers to investigate some salient features of the complex comminution process. The characteristics of the common single particle breakage tests such as single impact, double impact and slow compression tests are examined and the results from these tests are compared. A comparison of the results from single particle breakage tests with grindability and ball mill tests is given. Application of the results from single particle breakage tests to modelling industrial comminution processes is described. The necessity for further research into single particle breakage tests to develop a simple but comprehensive technique for estimating the breakage characteristics of ores is discussed.

Jan 1, 1986

By T. P. Meloy

Like our wives, the comminution of brittle solids is easy to recognize but difficult to describe. However, describing it we must. Describing the fracture mechanism of brittle solids permits the eventual mathematical quantification of the results, process optimization and control strategies. This paper presents a physical model of brittle solid comminution that explains why the slope of the log-log size distribution curves have a slope of one or less in the smaller particle sizes. To develop the hypothesis, modifications of the Gaudin Meloy physical model are made. In brittle solids, comminution takes place by cracks propagating through the material. These cracks may bifurcate as they move. Cracks may terminate either on the original surface of the material, or on a secondary crack within the material formed earlier in the comminution process.

Jan 1, 1994

By Brian Putland

Single stage semi-autogenous / autogenous (S/AG) milling has become a common design for a variety of ore types with the advantages of being comparatively low capital cost and flexible for future expansion. The single stage SAG/AG milling option is ideal for starter projects with significant exploration and expansion potential. Currently a number of the largest SAG mills designed are installed in single stage configuration. This paper discusses the challenges associated with the process design of single stage SAG/AG milling circuits, the design flexibility required to ensure a robust circuit and the operating techniques adopted at successful installations.

Jan 1, 2012

By J. Nakayama

Down-the-hole hammer is commonly recognized as the most powerful drilling equipment for weathered to fresh rock formation including boulders. However, its drilling diameter is restricted by reasons of difficulty to actualize large diameter drillhead and to ensure discharging means of cuttings. Cuttings are usually removed by flushing i.e. uprising return air after compressed air actuates hammer, but in case of large diameter drilling, as the clearance between drill rod and surrounding wall of hole become fairly large, necessary up-hole air velocity to transport cuttings can not be maintained. In case of marine or underwater drilling or high groundwater table, orthodox down-the-hole hammer is obstructed its operation by water. This single head hammer drill combined large diameter drillhead with reverse circulation of drilling fluid enables large diameter drilling extending to 1.5 m, i.e. actualized large diameter mechanical drillhead incorporated with ensured cuttings removal means enabled this range of drilling. This paper introduces its features and actual applications to large diameter bored pile drilling for varied sorts of rocks in maritime construction projects.

Jan 1, 1996

By Fritz Grübl

Modern shield TBMs allow tunnel drives through almost any type of ground. Thanks to high elaborated technical measures, significant subsidence of the ground surface can be almost entirely avoided. The tunnel lining behind the TBM must be capable of withstanding all loads without deforming, especially during ring erection and advance. Single-shell tunnel linings behind the TBM, usually reinforced concrete segmental rings, can be designed to fulfill this demand. With many projects, however, damage occurs to the lining. Repair costs may be extremely high. Reasons for damages and possibilities to avoid them are shown and explained.

Jan 1, 2001

By William G. Davenport, Eric H. Partelpoeg

Direct smelting of copper in a single vessel has long been the extractive metallurgist's dream. Such a process offers the important advantages of (i) maximum use of the energy available from oxidizing the sulphur and iron of the concentrate; (ii) restriction of SO2 emissions to a single constant-strength source; (iii) minimum materials handling and (iv) elimination of at least one process step. Extensive developmental work was carried out in the 1960's and 1970's to implement such single-step processes. Some of the processes reached the prototype stage and it appeared that copper smelting technology was on the threshold of a new, efficient, minimum-pollution era. Since that time, however, the forward thrust has slowed and single-step smelting is still a process of the future. The paper describes in detail the potential advantages of single-step smelting; its history and current status; and the reasons why it has not been adopted industrially. It concludes that the potential benefits of single-step smelting are powerful and that many of the difficulties encountered in the 1970's will be overcome in the 1980's.

Jan 1, 1985