Search Documents

By Robert Mehl

A STUDY of the structures arising from the decomposition of the a solid solutions in the Cu-Zn and the Cu-Al systems is of peculiar interest in the study of the mechanism of precipitation from solid solutions. It is possible in these alloys, by varying the composition within the ß field, to precipitate from the same basic lattice phases having different lattice structures. It has been rather generally assumed heretofore that the type of structure originating from the decomposition of a solid solution-the Widmanstätten structure-is determined by the lattice structure of the parent solid solution alone. In the first paper of this series1 evidence was advanced which threw doubt upon this hypothesis; but definite proof of the correctness or incorrectness of the hypothesis should be forthcoming from a study of these alloys, for if the structures originating, for example, from the precipitation of the a phase from ß and of the -y phase from the ß in the Cu-Zn system should be shown to be crystallographically different, the hypothesis would necessarily be held as definitely disproved. Furthermore, the newer proposal enunciated in the first paper of this series-that the origin of the Widmanstätten structure lies in a cooperation between the lattice of the parent solid solution and that of the precipitate-which at present seems the only alternative hypothesis, would in such an event be given added weight. The work here reported shows that the Widmanstätten structures originating in the precipitation of the a phase from the a and in the precipitation of the -y phase from the ß in the Cu-Zn system are indeed crystallographically different; and incidentally presents some new descriptive information on the Widmanstätten structure from a more general point of view.

Jan 1, 1931

By Karsten Zimmermann

The paper presents a study on the influence of face retreat rate in longwall coal mining on surface subsidence. It shows possibilities to influence dynamic ground movement by using a specific and controlled winning regime. For this, a dynamic stochastic prediction model used by DMT in Germany will be proved and adjusted on the specific character of geology in the Northern Appalachian coal field. Occurring ground movements such as inclination, curvature and deformation can be analyzed under static and dynamic points of view. It is theoretically shown that the face retreat rate has only a small influence on the static deformation values, but directly affects rate and acceleration of subsidence and deformation processes. The study shows that because of low mining depth and high mined thickness, static deformation values have the largest impact to surface objects. This implies that high face retreat rates don?t affect the impact on surface objects.

Jan 1, 2007

A thermochemical model is developed to study the two-stage smelting reduction process for ironmaking without post-combustion. Steady-state multi-material and heat balance equations are solved simultaneously to study the effect of metallisation, slag basicity, coal rank and heat loss on consumption rates of coal, ore, flux and oxygen and production rate of slag to produce hot metal of a given composition, tapped at a given temperature. The model is applied to the commercial data for a COREX-plant producing a wide range of hot metal compositions, tapped at different temperatures. The computed rates of coal, slag, flux, ore and oxygen were found to be close to the reported ones, but an exact match could not be obtained. It is found that a four per cent change in metallisation brings changes the coal rate by five per cent, flux rate by six per cent, slag rate by eight per cent and oxygen rate by 13 per cent, while a ten per cent change in basicity changes the coal rate by ten per cent, flux rate by 13 per cent and oxygen rate by 22 per cent. Further, it is found that an increase in metallisation decreases the coal rate and export gas. At a given per cent metallisation, the coal rate and the export gas are lowest for anthracite compared to all other types of coal.

Jan 1, 1999

By Chengguo Zhang, Bruce Hebblewhite, Faham Tahmasebinia, lsmet Canbulat

"Coal burst is a dynamic release of energy within the rock (or coal) mass leading to high velocity expulsion of the broken/ failed material into mine openings. This phenomenon has been recognised as one of the most catastrophic failures associated with the coal mining industry, which can often lead to injuries and fatalities of miners as well as significant production losses. This paper aims to examine the mechanisms contributing to coal burst occurrence, with an emphasis on the energy release concept. In this study, a numerical modelling study has been conducted to evaluate the roles and contributions of difference energy components. The energy analysis presented in this paper can help to improve the understanding of energy release mechanisms especially under Australian conditions.INTRODUCTIONCoal burst is one of the most hazardous problems encountered in underground coal mines, which occurs at different locations in a variety of mining systems and operations. This phenomenon always involves a violent and dynamic energy release with large rock mass/coal deformation and ejection that can cause severe damage to openings, equipments and may result in fatalities and injuries.The first coal burst occurrence was reported in Britain in 1738 (Dou 2001). Since then, international experiences are available in Canada, South Africa, USA, former Soviet Union, China, India, France, Germany, Poland and Czechoslovakia. Rice (1935) classified coal bursts as two general types, namely excessive pressure bumps and shock bumps and he further mentioned that pressure bumps are caused when pillar stress exceeds bearing strength. Shock bumps are induced by the breaking of thick, massive strata at a considerable distance above the coal-bed, causing the immediate roof to transmit a shock wave to the coal."

Jan 1, 2016

By Mani Manimaran, Inna Dymov, Mariam Melashvili, Chris Fleming, Joe O’Day

This paper presents experimental evidence that supports the use of bromine/bromide as a potential alternative to conventional cyanidation for gold leaching. The study evaluated a brominebased lixiviant, Stabilized Bromine, with considerably lower vapour pressure than liquid bromine. Using a rotating device, the rate of gold dissolution was determined at various concentrations of this reagent. The reactivity of pure pyrite, arsenopyrite and chalcopyrite minerals was also evaluated in stabilized bromine reagent. Furthermore, bromine leaching of gold in a number of gold bearing ores was undertaken. Results showed that significantly higher gold recovery can be achieved with bromine than with cyanide when leaching gold encapsulated in sulphides, but bromine consumption was high owing to simultaneous oxidation of the sulphides. The greatest promise for the bromine leach process was with oxidized gold ores. The recovery of gold from oxide ores with bromine was comparable to that achievable with cyanide and bromine consumption was reasonable when leaching was conducted at a near neutral pH of ~6. In the case of oxidized gold ores containing copper mineralization, it is possible that bromine consumption may be lower than cyanide consumption, since there is evidence to suggest that bromine is less reactive than cyanide with copper minerals.

Jan 1, 2014

By Xinhua Wang, Xuefeng Liu, Die Yang, Lifeng Zhang, Wen Yang

"CSP thin slab continuous casters are well used in recent years. The control of heat transfer in the mold is very important because it is correlated with several slab defects. The mean heat flux of CSP mold was studied based on the plant production data of LCAK steel and weathering steel. The effect of various operation conditions on the heat flux was analyzed and discussed. The results showed that the heat flux was 2.1-2.6 MW/m2 on the wide face and 1.2-2.2 MW/m2 on the narrow face for the casting of LCAK steels. During the casting of weathering steel, the heat flus was mostly 2.05-2.5 MW/m2 on the wide face and was 1.1-1.8 MW/m2 on the narrow face. The heat flux depended largely on the casting speed. The heat flux on the wide face increased obviously with increasing casting speed when the casting speed was relatively low; however, at high speed, the heat flux increased slowly or kept constant. At low casting speed, the heat flux depended little on the superheat of the molten steel. The mean heat flux depended little on the level fluctuation at continuous casting mold.IntroductionCSP thin slab continuous casters are used more frequently in recent years for its low cost of construction and manufacturing. The structure of CSP mold is very different from that of conventional thick slab casting mold, inducing the difference of heat flux between them. There have been some studies about the heat flux of thick and medium slab casters [l, 2]. Heat transfer in the mold is very important for the solidification of molten steel because it is correlated with several slab defects such as slab break-out, longitudinal crack, and surface depression. Moreover, higher casting speed is desired to improve the productivity. The control of solidified shell is extremely important. The heat flux is largely influenced by several casting parameters such as the cooling intensity of the mold, the casting speed[3], the mold flux powder [3, 4] and the carbon content of steel as well [5]. The investigation on the heat flux and affecting parameters can help to understand the solidification of molten steel in the mold."

Jan 1, 2013

By B. McKevitt, P. Abbasi

The ion exchange process (IX) is applied in the mining industry for the removal of impurities from process streams, treatment of waste solutions prior to disposal and the recovery of valuable metals. Extensive studies have been performed with the goal of modeling of IX for the case of a single metal loading onto iminodiacetic resin in the hydrogen form. However, in a real system, a resin may be saturated by impurities (iron, calcium, magnesium, manganese), which are then displaced by the metal of interest. The present study provides an insight into the Fe2+ loading process onto iminodiacetic ion exchange resin under the infinite solution volume condition. The study involves the measurement of iron loading under a variety of experimental conditions as well as an attempt to model the loading process using the hybrid correlation advanced by McKevitt (2012). The importance of the experimental and modeling work are discussed in the context of resin in pulp recovery of nickel.

Jan 1, 2014

By G. Walsh, M. T. Wild

In this paper the performance effects of linear shaped charges will be discussed. Different sized charges were tested and reviewed based on their performance used with a typical detonation method vs. detonation with a line wave generator. The goal of the project was to determine if the linear shaped charge had better performance with an ideally linear wave moving through it, verses a swept wave that is currently used. A line wave generator is a flexible sheet explosive formed into a triangular shape with holes placed in strategic places to cause a detonation wave to become linear across the width of the triangle. A standard linear shape charge with a detonator in the side of the charge was be detonated against a witness plate to get a standard depth of penetration. A second standard linear shape charge with a detonator connected to the top of a line wave generator, the line wave generator placed on top of the linear shape charge, was be detonated against a witness plate to get a comparison depth of penetration. All charges had a standoff 1.5 times the width of the cavity, allowing the data to be compared to the control charge. Computer modeling was intended to be used to predict the results from testing these designs in the field. The actual results were compared among themselves.

Jan 1, 2011

By Someswar Kesh, Gavin J. Faulkner

Introduction Powered supports in longwall mines essentially operate under two conditions: 1. Static (non-working) 2. Dynamic (working) There is a variety of static conditions which may exist in a mine. These may include a temporary stoppage of work for a few minutes or stoppage of work for days because of strikes or lack of demand for coal. Studies on pressure behavior were made during brief stoppages of work (few hours) as well as a long stoppage of work (two weeks). In dynamic conditions, the pressure variation on supports is expected to follow a certain pattern. However, in many cases that does not happen. Pressure-time characteristics of each leg of the supports were studied. This paper discusses the research findings of the studies made on powered support pressure behavior under both static and dynamic conditions. Studies on Pressure Variation in Static Conditions It has been noted (Brenner et a1.,1975) that the pressure distribution on mechanized longwall faces is random in nature and changes with time and position along the face. Figure 1 and Figure 2 show the distribution of support pressures for the front left leg of supports in two different mines. In both the cases it can be seen that the variation of the support pressures along the face is indeed absolutely random. However, the nature of randomness in both the cases is very different. The data in Figure 1 (Mine 1) is much more random than the data in Figure 2 (Mine 2). This can also be seen from the standard deviation of the data (81 26 Pa versus 4000 pa) . By comparing the results of ten other sets of data the same conclusions can be arrived at. Since it was found that in Mine 1, the pressure on support legs was extremely random, batches of ten supports each were taken and the mean pressure plotted. This mean pressure line is shown in Figure 1. It was expected that this would smooth out the variation due to individual props and reveal a better picture of the support pressure distribution. For the case cited, the standard deviation is lowered to 5043 Pa from 8126 Pa which indicates that, on an average, the supports tend to take loads more uniformly, however for individual support legs the load on the supports is very random. The significance of this is that, if the supports are selected on the basis of theoretical load calculations alone (based on the roof block concept or some other concept), only the mean value of the support load required will be known. In the case of a pressure distribution with a high standard deviation, some supports selected on the basis of mean value will fail, while others will be supporting low loads. Hence, for proper selection of support capacity, it is not only necessary to know the average load but also the expected nature of the distribution. The only reason why the supports are supporting the roof in Mine 1 well is the fact that the yield load is above the highest level of load attained. If Mine 2, which has a much higher average load, had the same sort of standard deviation, the loads on the individual legs could easily exceed the support load. For example, if the pressure distribution followed a normal curve and the mean pressure was 36,700 Pa with a standard deviation of 9000 Pa, it is possible that 67% of the supports will be within the pressure range of 36,700 plus or minus 9,000 Pa, or 22,700 and 45,700 Pa. Many of the supports could then exceed the yield load of 40,000 Pa. It is clear then that the mean load is an inadequate criterion for estimating support resistance. The nature of the problem is statistical and such an analysis should therefore be made as far as pressure data are concerned. Statistical Analysis of Pressure Data. In general, in longwall mining and other geo-mechanics studies, it is extremely difficult to specify the exact nature of the distribution of a variable. Under these circumstances, probability

Jan 1, 1986

By M I. Pownceby, S Hapugoda, V Nunna

Deposits of low-grade iron ores containing abundant goethite are distributed across the world. A common difficulty associated with beneficiating goethitic-rich ores is the poor liberation characteristics of the iron-bearing minerals which often contain finely disseminated gangue minerals such as kaolinite, gibbsite and quartz. Microwave-assisted heating has been proposed as an effective way of inducing dehydroxylation and associated mineral transformations in order to beneficiate low-grade goethitic ores. In this research, the mineral transformations occurring in a low-grade goethite-rich sample using microwave radiation was studied. Roasting conditions (up to 1000°C and under various CO/CO2 gas atmospheres) were designed to generate a magnetic product from a goethite-rich, reject waste stream sample sourced from an iron ore processing site in the Pilbara, Western Australia. Conditions (T, pO2) for transforming the raw material from hydrated goethite to hematite and eventually to magnetite are presented. Chemical and mineralogical characterisation of the raw material and roast products were conducted using X-ray fluorescence, X-ray diffraction, optical microscopy and scanning electron microscopy techniques to identify the mineralogical and chemical changes occurring during the heat treatment. Further steps are suggested to optimise the microwave-assisted magnetising roasting and correlate it with the application of magnetic separation techniques to maximise the efficiency of upgrading the iron content in low-grade iron ores.CITATION:Nunna, V, Hapugoda, S and Pownceby, M I, 2017. Study of microwave-assisted magnetising roasting and mineral transformation of low-grade goethite iron ores, in Proceedings Iron Ore 2017, pp 575–582 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Y. Huang

Corrosion of GaAs in aqueous electrolytes is a major limitation in implementing GaAs-based photoelectrochemical solar energy conversion systems, In this work, the corrosion behavior was investigated by electrochemical methods and surface analysis approaches, in both H2SO4 and NH3?H2O solutions, Open-circuit measurements showed that the cleaned GaAs surface was very sensitive to water/air, Impedance measurements for n-GaAs showed that an inductive loop only appeared at a high corrosion rate because a reaction intermediate is the oxidant for a further decomposition step in combination with chemical reaction with water, The results suggest that the same corrosion/decomposition mechanism occurred on n-GaAs in the two solutions, When the surface-hole concentration was low, the hole injection or generation process was the rate-determining step, At large reverse bias on n-GaAs, with high-hole concentration, the corrosion rate was limited by a Faradaic adsorption process, involving an adsorbed intermediate, The different surface compositions after corrosion in the two solutions can be explained by the dissolution of As(0), Further oxidation of As(0) to As(III) in NH3?H2O solution is still slow, as suggested from X-ray photoelectron spectroscopy (XPS) analysis,

Jan 1, 2005

By C. E. Johnson, R. L. Bauer, E. M. Johnson

In industry, the strength of a blasting cap is often equated to the type of explosive it can detonate. Comparable cap strength is becoming less important as nearly all caps manufactured today can initiate high explosives, such as primasheet, with ease. Previous studies were conducted to assess the quantity of energy released by various detonators into the directional propulsion of the detonator’s casing. However, the question of how much of this propulsion energy is needed to initiate an explosive remains unanswered. This study will assess the fragmentation size and velocity needed to initiate a high explosive when they are not in direct contact. For this study, primasheet was used as the main charge as it is relatively insensitive and can be situated in different positions relative to the detonator. Electric, non-electric and electronic detonators were used to evaluate initiation potential. The primasheet is observed in response to being in contact with a detonator, and not in contact with the detonator at various distances and angles. This allowed the quantity of energy transferred into the primasheet to be observed and for the initiation of the sheet to be recorded using high-speed video. This study will report the energy necessary to initiate the primasheet at various distances and angles from the charge from a number of widely used, commercial, hot wire blasting caps.

Feb 6, 2023

By J Zhou, X Bi, Y Yan, W Peng, H Yang, D Weng, P Li

Fortescue Metals Group (FMG) fines from Western Australia is a hematite and limonite mix characterised by high crystal water content. Due to its higher supply capacity and lower prices, the Wuhan Iron and Steel Corporation (Group) intended to use more FMG fines in the sinter mix. It is understood that sinter quality is closely related to its microstructure featured by the hardness and brittleness of different mineral phases, the content of micro pores, and trans-cracks. In order to maintain sinter qualities such as tumble index, reducibility and so on at higher FMG fines blend ratios, a research project was initiated to study the effects of the FMG fines blending ratio on sinter microstructure. Research results showed that at higher FMG fines ratios, the hardness of hematite and magnetite were both decreased while the hardness of calcium ferrite showed a tendency to decrease. The number of cracks that were generated during Vickers hardness measurement in various mineral phases decreased, but their length was shortened, and the variation of crack lengths increased. The contents of hematite and magnetite were also reduced and the reduction of magnetite was clearer. Also the content of calcium ferrite and pores rose and the magnitude of the increase of pores was greater. Among all the mineral phases in sinter cakes, the Vickers hardness of hematite was highest within the range of 879 N/mm2 ~ 942 N/mm2, and therefore the decrease of its content in sinter and the enhancement of its brittleness, ie the number of cracks increased, were harmful to sinter strength. In addition, the excessive increase in pores content is also not favourable to sinter strength.CITATION:Bi, X, Yan, Y, Zhou, J, Peng, W, Li, P, Yang, H and Weng, D, 2013. Study of sinter microstructure with various blend ratios of Fortescue Metals Group fines, in Proceedings Iron Ore 2013 , pp 331-336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By V Malysiak, N J. Shackleton

In the flotation of platinum group minerals pyroxene is a major gangue mineral. This study shows using zeta potential and ToF-SIMS analyses that when pyroxene is exposed to copper, nickel and/or calcium ions in solution at alkaline pHs a surface reaction occurs between the hydroxy species, in the case of copper and nickel, or divalent calcium ions and the pyroxene surface which influences the floatability of the pyroxene. Following exposure to copper and nickel ions at pH 9 addition of SIBX resulted in the pyroxene floating readily. It is also shown, in the case of copper, that the activating effect of the adsorbed copper hydroxy species can be reduced by the addition of complexing amines prior to SIBX. Proposals are made to explain these observations.

Jan 1, 2005

By Jochen Petersen, Thandazile Moyo

"The oxidative leaching of chalcopyrite in ammoniacal solutions has been evaluated using electro-analytical techniques. The anodic dissolution process has been established to be a seven-electron transfer process under nitrogen in ammonia–ammonium sulphate solutions and ammonia–ammonium carbonate solutions. The number of electrons transferred in the carbonate and sulphate salts suggests that the sulphur is oxidised to a thiosulphate intermediate and the copper and iron released as Cu+ and Fe2+. The Cu+ and Fe2+ is subsequently oxidised in solution in non-Faradaic reactions. The deportment of Fe2+ and S2O32- is affected by choice of the ammonium salt used in the leaching process. In the perchlorate salt, only five electrons are transferred, however observations made on the mineral surface after leaching do not support the formation of elemental sulphur. Scanning electron microscopy and energy-dispersive spectroscopy analysis of the mineral surface suggest presence of an iron–sulphur surface layer completely free of copper under the ammonia–ammonium sulphate conditions, an iron-rich surface layer under ammonia–ammonium perchlorate solutions and absence of surface layer build up under ammonia–ammonium carbonate solutions. INTRODUCTION Hydrometallurgical processes for copper extraction provide a viable route to recover the metal from mixed and low-grade ores, as well as overcome the environmental challenges faced by the traditional pyrometallurgical processes. Chalcopyrite is not only the most abundant of the copper sulphides, but also the most stable, making it recalcitrant to hydrometallurgical processes. Hence, hydrometallurgical processing of chalcopyrite continues to be an attractive area of research due to the vaguely understood surface chemistry of the mineral in different aqueous media. Different approaches to hydrometallurgical treatment of chalcopyrite can be carried out. These include thermal treatment prior to leaching, direct leaching and direct electrochemical leaching (Venkatachalam, 1991). Direct leaching of chalcopyrite can be carried out in various solution systems, as reviewed by Roman and Benner (1973) and Venkatachalam (1991). Ammoniacal solutions are attractive and effective lixiviants that form stable amine complexes with some base-metal cations while rejecting iron. Leaching of chalcopyrite in ammoniacal solutions in the presence of an oxidant is possible due to the stabilisation of copper(I) and copper (II) by ammonia at elevated pH levels. In oxygenated ammonia solutions, it has been suggested that chalcopyrite dissolves according to Equation 1 (Beckstead & Miller, 1977a):"

Jan 1, 2015

By Isauro Rivera Landero, Martín Reyes Pérez, Eduardo Cerecedo Sáenz, Javier Flores Badillo, Mauricio Guerrero Rodríguez, Juan Hernández Ávila, Eleazar Salinas Rodríguez, María Isabel Reyes Valderrama

During column flotation of mining tailings of the Dos Carlos dam, it was observed that the effect of surface liquid flow (JL) is a variable that determines the rate of rise of packing bubbles and therefore, causes the generation of gas retained within the columnar system. Also overall more stable laminar flows were observed, in a range of superficial flow of liquid in the bottoms stream (JLT) from 0.446 to 0.68 cm/s, showing the stability in the range of superficial gas flow (Jg) from 0.1 to 0.5 cm/s. Observing a uniform bubble size for the three JLT evaluated, with a diameter between 0.05475 and 0.2525 cm, at all the range evaluated of Jg. Furthermore, an uniform performance was obtained, and with the same rate of rise of packing bubbles, showing a greater packing bubbles at JLT = 0.446 cm/s, due to the lesser bubble size observed, in comparison with the values of JLT of 0.68 and 1.017 cm/s.

Mar 1, 2017

By D. Endara, E. De la Torre, S. Echeverria

"The study was conducted with the sulfide mineral from the province of Zamora Chinchipe. It was characterized physical, chemical and mineralogical, obtaining between its main results a copper concentration of head ore of 0,58 %. The mineral was homogenized and taken to direct closed circuit: rollers mill - vibratory sieve (mesh # 16). Flotation was carried out in two stages: the collective and selective where in each one were performed 6 water recirculation as suggested by the technique used to relate information of a batch flotation to a continuous circuit called cyclic flotation tests (LCT). In the collective flotation (bulk) 2 Kg of mineral were grinded with 10 Kg of balls for 30 minutes and 62.5% of solids, the pulp was taken to the flotation process with solids percentages of 33.3% and pH 7, it was conditioned with 45 g / t of KAX 1%, 50 g/t of Aerofloat 208 and 20 g /t of Pine oil. The concentrate and tailings bulk obtained were filtered separately for the recovery of water and it was recirculated to the next grinding of 2kg mineral. In the selective flotation 1Kg of bulk concentrate was carried to regrind for 40 min, 62.5% percent of solids, 10 g of lime and 5 g of tannin FLOATAN T5, the pulp was taken to the roughing-collection-refining flotation circuit controlling the pH between 10.5 and 11 where conditioning (60 g/t of Aerofloat 208 and 30 g/t of Pine oil) and adding lime to the circuit and FLOATAN according to the procedure. The four fractions obtained from the circuit were filtered; the water was recirculated to the regrind process of the bulk concentrate. In the collective flotation process tends to stability in the fourth recirculating water to obtain a copper content of 4.5% and a recovery of 87%, recirculated water represents 69.8% of all water used in the 6 recycles. In the selective flotation circuit the fifth recirculating of water is the optimal where obtaining a copper content of 13% and a recovery of 72%, recirculated water in the selective flotation circuit represents 95% of the total water used in the 6 recycles."

Jan 1, 2018

By B. Y. Tuo

This article presents results of studies performed to determine the feasibility of using low-grade limonite ores from Yunnan deposit. Laboratory tests and commercial trials have shown that the magnetic separation can be performed with a high high-grade concentrates. The quality of the preparation concentration meets the requirements for blast-furnace smelting. The results as a whole demonstrate the feasibility of utilizing bank limonite ore. Yunnan limonite?s magnetic separation, roasting magnetic separation and flotation experimental study shows that grade of the ore grade can been from 32.91% heighten to 58.64%, a recovery of iron is 90.87%, productive rate is 51% through orthogonal test optimization; roasting magnetic separation can obtain that the grade of iron preparation concentrate is 61.16%, recovery is 67.39%, productive rate is 36%. As far as economy and enviormental protection is concerned, strong mag-netic suggested a more appropriate process. Keywords: Limonite; Roast; Magnetic separation

Jan 1, 2014

By M. Dupuis

It has been previously demonstrated [l] that there is no obvious thermal balance related issue limiting the size of a Hall-Héroult cell. Yet, it is well known that a forced-air sidewall cooling system is part of the AP50 cell design [2], In the present study, the authors analyze the impact of thermal loading on the mechanical deformation of high amperage cell potshells. The effect of adding cooling fins or a forced-air sidewall cooling system is then assessed.

Jan 1, 2005

By Qidong Zhang, Yongsheng Song, Wenjuan Li, Guiying Zhou, Kun Song

"Molybdenum is a very important rare mineral resources, which exists largely in oxidized ores and sulphide ores in nature. About 99% of metallic molybdenum comes from molybdenite. The talcose molybdenum resources are abundant but the resources utilization is low, because the talc is naturally hydrophobic and the floatability of talc is similar with molybdenite, which lead to difficult separation by flotation. Talc is easy entry into concentrate in flotation which can cause the content of MgO overhigh, therefore the molybdenum concentrate grade can not meet the industrial requirements. Thus the utilization level of talcose molybdenum resources has been restricted greatly.The adsorption of water on talc and molybdenite surfaces and natural floatability of minerals were studied by density functional theory method. The results showed that molybdenite and talc were layered minerals which exhibited similar surface wettability and H2O molecule prefers to stay with water rather than the minerals surfaces. N2 is adsorbed on talc and molybdenite surfaces more easily than H2O. The interaction and flotation behavior were studied by SEM and flotation experiments. The reason why talc interferes with the flotation molybdenite has been revealed. The agglomeration between molybenite and talc was caused easily in neutral or acidity solution, and it was dispersing between molybenite and talc particles in alkaline solution. The flotation results showed that good floatability of talc was the key factor causing a low grade of concentrate in alkaline solution. Thus, it is the key factor to enlarge floatability difference between molybdenite and talc.INTRODUCTIONMolybdenum is a kind of important rare metal and strategic reserve resources (Zhitao Y et al, 2016a). Due to excellent characteristic, such as high melting point, good thermal property and et al, it’s widely used in metallurgy, machinery, chemical, aerospace, and many other areas. It has become an indispensable metal in modern industry. Molybdenum generally exist in the form of molybdenite which is a kind of mineral with excellent natural floatability. Talc is a kind of typical hydrous and layered magnesium silicate minerals (Beattie D et al,2006a), which is one of the most common gangue mineral of the platinum group metal ores and metal sulfide ores (Tao L et al,2011). Due to its good native floatability, talc is easy entry into the concentrate product with foam in the process of sulfide ore flotation (Kelebek S and Smith S, 2006b), which resulted in decreasing concentrate indexes. Not on that, the high-content MgO of concentrate will also produce a series of adverse impact to the subsequent smelting (Lotter N O et al, 2008). Therefore, it is difficult to separate talc from sulfide ore concentrate effectively."

Jan 1, 2018