Search Documents

By Bain J. H

Since zinc was first deposited at Risdon in February, 1917, provision of the most economical cathode assembly has been a subject of extensive research, the major problems being corrosion and efficient use of power.From the corrosion viewpoint, a perfect cathode is one in which the life of the headbar and the deposition sheet are the same. However, corrosion usually concentrates in a narrow zone across the face- of the sheet, resulting in breakages which, before the advent of argon arc welding, meant a loss of a 'complete assembly.Attempts to extend sheet life included use of thicker sheets, multitudinous protective coatings applied with varying degrees of success, re-rolling, and for a time, aluminium consumption was reduced when broken sheets found re-use as protecting strips. This latter economy became impracticable when electrode spacing was reduced for greater efficiency in power utilization.As an integral part of the electrode, the headbar was modified accordingly. Copper headbars, although more corrosion resistant, were replaced by aluminium due to a possibility of dissolved, copper promoting deterioration.Thicker electrodes and regulated spacing reduced internal shorting, whilst provision of knife-edge type supports on both contact and insulator ends of headbars aided in electrode centralising and continuous electrical conduction.After much experimeIitation, an assembly has been evolved which, with the aid of argon arc welding and tbe use of minimum additional aluminium, permits comparable headbar and sheet lives, combined with good electrical conduction throughout the life of the cathode.INTRODUCTION Over 300 tons of zinc are produced daily at Risdon from a purified zinc sulphate solution by electrolysis, the zinc being deposited upon all-aluminium (except for copper contact) cathodes. It is stripped in 72-hour cycles from the cathodes, melted and cast into the customary rectangular slabs.

Jan 1, 1958

By Aaron Jones, Guy Reed, Russell Frith

"In 2017, one of the international authorities on coal bursts, Dr. Chris Mark, published a paper entitled “Coal Bursts that Occur during Development: A Rock Mechanics Enigma,” in which several relevant technical issues were identified, the most pertinent being:i.whilst development coal bursts are commonly associated with geological faults, understanding which specific faults result in burst-prone development mining conditions and why, remains undefined.ii.conventional wisdom in relation to strong roof and floor geology of the coal seam might be limiting, based on certain burst examples in Colorado.iii. development coal bursts can occur without the local ground stresses being substantially elevated from their in situ levels.This paper outlines what is considered to be a credible, first-principles, mechanistic explanation for these three current development coal burst conundrums by reference to early published coal testing work examining the significance of a lack of “constraint” to coal stability and an understanding of how very specific structural geology and other geological features can logically cause this to occur in situ, albeit on a statistically very rare basis. This basic model is examined by reference to published information pertaining to the development coal-burst that occurred at the Austar Coal Mine in New South Wales, Australia, in 2014 and from the Sunnyside District in Utah, USA.The “cause and effect” model for development coal bursts presented also offers a meaningful explanation for the statistical improbability for what are nonetheless potentially highly-destructive events, being able to explain the statistical rarity being just as important to the credibility of the model as explaining the local conditions associated with burst events.The model could also form the basis for a robust, risk-based approach utilising a “hierarchy of controls” to the operational management of the development coal burst threat. Specifically, these include the use of pre-mining predictions for likely burst-prone and non-burst-prone areas, the use of the mine layout to avoid or at least minimise mining within burst-prone areas if appropriate, and finally the development of an operational Trigger Action Response Plan that reduces the likelihood of inadvertent roadway development into a burst-prone area without suitable safety controls already being in place."

Jan 1, 2019

The refractory nature of residual gold in Kalgoorlie calcines is caused by occlusion in dense pyrrhotite formed by fusion within pyrite grains during decomposition. Fusion of pyrite increases as the rate of heating exceeds the rate of sulphur expulsion. By controlling these rates in relation to each other in a fluidised system fusion is limited and an expanded structure is formed. The increased area presented to cyanide solution, and the decreased diffusion distance, makes gold more accessible for extraction. Gold extraction from expanded pyrrhotite, before oxidation for porosity, is comparable with extraction from fully oxidised calcines from Edwards roasters. A method is suggested for standardised comparison of cyanidation residues.

Jan 1, 1957

By John A. Breslin

The year 2010 will mark the 100th anniversary of the beginning of the research efforts by the U.S. government to improve the health and safety of miners working in the United States. This research began in 1910 with the establishment of the U.S. Bureau of Mines (the Bureau) and it has continued during the past 10 decades, even after the closure of the Bureau in 1996. The research on safer mining technology, formerly done by the Bureau, has now been combined with National Institute for Occupational Safety and Health (NIOSH) studies of miners? health to form a unified federal research program to improve the health and safety of miners. This article describes this research and places some of the accomplishments into perspective with other activities in the U.S. Mine Safety and Health Time Line (insert).

Jan 1, 2010

By Douglas W. Fuerstenau, Pradip Pradip

The design and development of selective flotation collectors has been the key to the remarkable success of flotation in beneficiating complex, difficult-to-process ores. Sustained research efforts in the field over the past hundred years have led to delineating the scientific basis of selective mineral flotation in terms of the crystal chemistry and the surface and colloid chemistry of minerals including their solubility, and the aqueous solution chemistry of added reagents. It is now well-established that the electrical double layer theory (EDL) is the most powerful means of quantifying the relative strength of mineral-reagent interactions in the case of nonsulfide minerals. We illustrate the utility and the power of the EDL in delineating the science underlying selective mineral flotation with the help of a few examples taken from our own work, in particular on the selective flotation of rare-earth minerals (bastnaesite) from associated semisoluble minerals (barite and calcite) using alkyl hydroxamate collectors and the flotation separation of lithium-containing minerals (spodumene) from associated alumino-silicate minerals with oleate (fatty acids). Both of these mineral separation systems are of contemporary research interest and of immense value to the industry today. Recent advances in utilizing molecular modeling computations, particularly in the context of quantifying the effect of crystal chemistry and the relative distribution of adsorption sites available on mineral cleavage planes, are also reviewed.

By V. K. Kollipara

Air flow patterns in the face area of a room-and-pillar mining are critical for understanding the dust dispersion characteristics and for developing engineering controls. SIUC has previously performed a CFD study to analyze the airflow patterns in the face area when continuous miner is making a straight cut. Results from this study identified low air velocity and re-circulation zones in the face area and illustrated the significance of line curtain, and scrubber operation on the air flow patterns. This paper discusses similar analyses when continuous miner is making a right turn cut as it is considered to be the dustiest cut among all the cuts made to advance an entry through a crosscut. This paper presents results for box-cut development for a right hand turn x-cut. This paper also addresses line curtain advance and air leakage through the curtain on the airflow patterns in the face area for such a cut. Low air velocity and recirculation zones were identified by analyzing the velocity vectors.

Jan 1, 2012

By Jussi Vaamol

A commercial CFD-code was used to solve isothermal flow fields of gas and liquid in a Peirce-Smith converter. The model was validated with a 1/4 scale water model, and parametric study. Limits of the modeling technique used were recognized, but calculated results indicate that the present model predicts the general flow field with reasonable accuracy. The model was used to examine general flow conditions in an industrial scale PS-converter. Typical scaling factors of physical models were also evaluated with the aid of predicted bubble distribution, patterns of the flow fields and magnitude of flow velocities. The numerical simulations were found to open new viewpoints to the fluid dynamic related phenomena in the PS-process.

Jan 1, 1998

By H. Pearce, A. E. Lewis, A. Ochieng

Hydrodynamics and mixing are fundamental to the operation of mineral process systems such as flotation cells and metal precipitation reactors. The computational fluid dynamics (CFD) technique has been employed in the present work to study the hydrodynamics in a mixing vessel stirred with either a Rushton turbine or a pitched blade impeller. The multiple frame of reference (MFR) approach has been used to model both impellers. A draft tube was used only in the Rushton turbine stirred vessel. The flow profiles for the pitched blade impeller have been studied in three regions; below the impeller tip, at the middle of the tank, and near the liquid surface. The simulation results were compared with literature data obtained using a laser Doppler velocimetry in the three regions of the vessel, and it was found that the model predictions were better in the impeller region. There was a poor prediction of the experimental results in the region closer to the liquid surface; however, this was improved when the turbulence parameter (C2) in the k-e model was set to a higher value. The value of the impeller clearance at which the Rushton turbine generates an axial impeller type flow has been determined and it has been shown that, at this clearance, a draft tube can be used to enhance axial flow in a Rushton turbine stirred reactor.

Jan 1, 2003

By Hazel Lyman Nickel

Daring to try where others had failed, Herbert and Lou Henry Hoover translated from the Latin the principal (and first) textbook on the mining and metallurgical profession, De Re Metallica, 1556, which had been in use for two centuries and then had lain dormant for 350 years in a language unreadable except by a chosen few. Thus the Hoovers enriched the English tongue with a vitally important contribution to history in the fields of mining, metallurgy, and chemistry. To them it was a joint hobby, because they were actively interested in the beginnings of the mining profession in which they had both been trained. Illuminating the years of toil to perfect this translation shone their ideal of service to humanity, since, in the Preface, they refer to their task as "a labour of love", which had to find the moments for its execution in night hours, weekends, and holidays, extending over a period of about five years. And they add: "If the work serves to strengthen the traditions of one of the most important and least recognized of the world's professions, we shall be amply repaid". While a student at Stanford University, during the years of 1891-95, Herbert Hoover had become familiar with a copy of this Latin mineralogy classic, De Re Metallica, a rare book in the private library of Dr. John C. Branner, at that time head of the department of geology and mining. Another Stanford student in geology was also examining and studying the ponderous volume of twelve 'books'. She was Miss Lou Henry, of Monterey, who graduated in 1898, and the following year became Mrs. Herbert Hoover. Interwoven through the tapestry of their life experiences gleamed the silver thread of their interest in this mediaeval Latin textbook. Just nine years lacer, the Hoovers had commenced their translation, while they were in temporary residence in London after the seething years in China under the shadow of the Boxer rebellion.

Jan 1, 1949

By D. R. Knowlton

IF I were a minister, and this were a sermon, and such a passage appeared in the Bible, I would choose for my text: "From whence cometh the oil for our war?" And no preacher was ever more serious than I am. You petroleum engineers recognize that the producing branch of the industry is passing through an era of plenty and inflated potentials into an era of scarcity and unmet allowables. Not too long ago the oil operators of Kansas, California, and Texas were appearing before operators' meetings and regulatory authorities asserting that these States were capable of producing at rates far in excess of what the demand at that time would absorb. Today every oil-producing area in the United States except the Texas Gulf Coast and West Texas is producing close to or in excess of its maximum efficient rate.

Jan 1, 1943

By J. Golamnejad

This paper attempts to model long-term production scheduling problems by chance constrained binary integer programming in a stochastic environment. This stochastic model is set up to account for ore block grade uncertainty. The probability distribution function of grade in each block is used as a stochastic input to the optimization model. This distribution function in each block should be determined using a Geostatistical Simulation approach. The deterministic equivalents of these chance constraints are then achieved, which are in the form of nonlinear in binary variables. A confidence level at which it is desired that the uncertain constraints holds, is specified in each scheduling period. Rather than the previous risk-based model, this formulation will yield schedules with a high chance of achieving planned production targets while maximizes the expectation of net present value and minimizing the variance function simultaneously. Using this method, the grade uncertainty is integrated explicitly into the optimization process.

Jan 1, 2006

By R Wynn, N Stoitis, R A. Lauten, H Liang

At the Century mine in North West Queensland, MMG produces lead and zinc concentrates. The current production rate is close to 500 000 t of zinc per annum. Graphite is the main gangue in the orebody and a substantial quantity of chemicals are used to achieve an acceptable depression of graphite and other gangue materials in the current operation. In the future, it is anticipated that the content of graphite in the orebody will increase while the zinc grade will gradually drop. This scenario illustrates the importance of an optimised suite of flotation chemicals to maximise concentrate grade and recovery. As an alternative to the current reagent suite where dextrin is used to depress graphite, laboratory test work and subsequent plant trials were conducted with alternative depressants. These depressants facilitated both graphite depression and elevated zinc grades in the rougher concentrate. As an added benefit, it was also observed that the silica content in the zinc concentrate was reduced in the presence of the biopolymer selected for the plant trials. Results from both laboratory tests and plant trials will be discussed to illustrate how this change of reagent suite improved flotation yield at the MMG Century Mine.CITATION:Wynn, R, Lauten, R A, Liang, H and Stoitis, N, 2014. A change in graphite depressant to improve the recovery of zinc at MMG Century mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 179–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

DCF Valuations are very important to individuals and companies involved in the mining industry. Such valuations are critical to investment decisions in relation to new and existing projects. In particular they provide fundamental information to shareholders in the event of a capital raising or takeover and to financiers supporting mining companies and projects. Also, DCF Valuations are often used to support asset carrying values in the financial statements of mining companies. This paper presents a Chartered Accountant's (CA's) perspective on the main issues to be considered in preparing, analysing and relying upon DCF methods in mineral valuations and provides some practical examples relating to key issues. The paper makes the important point that DCF methods involve making assumptions about future events and circumstances that inherently contain uncertainty which results in a valuation prepared on a DCF basis providing a range of values that are not perfect or accurate. In order that DCF valuations provide meaningful information the underlying methodology used and assumptions made must be consistent, sound and well supported. Credibility of those involved in preparing mineral valuations is vital and this paper supports the adoption of sound practices by all concerned.

Jan 1, 1994

By W. McA. Johnson

THE work of J. E. Johnson, Jr., on the effect of small amounts of oxygen in cast iron in increasing its strength and resistance to shock, is of interest from the technical and scientific standpoints. The following exposition of the theory carries Mr. Johnson's explanation further and, in my opinion, will disclose certain related phenomena and perhaps shed further light on the subject. Some facts, so novel in character as to excite incredulity, have been accepted finally by many metallurgical authorities. One of these is that oxygen to the amount of 0.060 per cent. in cast iron gives it a breaking strength of 3,500 lb. per square inch, compared with a breaking strength 2,500 lb. per square inch in cast iron of the same composition with re-ect to elements other than oxygen, but having only 0.010 per cent. oxygen. The "oxygenated" cast iron, even if made in a coke furnace, has properties equivalent to the best charcoal pig iron. Mr. Johnson has also established the fact that the variations in combined carbon cannot account for the results. By microphotographic evidence he has shown that in oxygenated cast iron the graphite particles are dense and spherical, while in well-deoxidized cast iron the graphite particles are flaky and leaf-like. It is just a matter of common sense that iron of the latter structure is much weaker than the former. The analytical and microscopical work has been done with care and there is no doubt in my mind about the accuracy of the, experimental results. In this paper then, we shall consider it as accepted that small amounts (0.060 per cent.) of oxygen increase the strength of cast iron by producing a structure in which the round and solid particles of graphite are surrounded firmly by a principal matrix of ferrite. The purpose of this paper is to show that the reason why the graphite particles are round is founded on the fact that the particles of any precipitate are made denser and harder by the presence of a reagent having a solvent action on the precipitate. This can be stated as a law, although I have never seen it so given in any textbook.

Jan 2, 1916

By A. J. Weinig

NEED for some simple method of determining tonnages in mill circuits has always been felt by operators and consultants alike. To meet this demand the following method was evolved and has been found accurate and practical after considerable testing on various mill flows. The essence of the method is to add a chemical at a uniform rate to a mill flow, such as a launder conveying pulp, and then determine the concentration of the added chemical in a sample of the pulp. From this procedure the tonnage can be calculated. Common table salt has proved the most satisfactory chemical for ordinary conditions. It has many decided advantages for use in tonnage determinations, among them being the following:

Jan 1, 1933

Results obtained from small scale tests using Australian tin concentrates indicate that metallic tin containing less than 0·1 per cent iron can be recovered by a two-stage process using hydrogen and make-up chlorine. In the first stage the concentrate is ground,. pelletized, roasted, and reacted at 650°C with HCI and H2 to volatilize the tin as SnOI2. The volatilization reaction is conducted with cocurrent gas and solids flow because it was found that the use of cocurrent flow yielded a solids residue substantially free from FeCI2. The second stage uses a technique termed "reflux reduction" during which the SnOl2 produced by volatilization is reduced by hydrogen to form tin and a gas containing HCI and H2 of sufficiently high HCI tenor for recycle to the volatilization stage. The elimination of tin ranged from 98+ to 99·7+ per cent of the tin from concentrates containing 5 to 50 per cent tin, respectively. The process should be capable of continuous operation, and a tentative calculation has shown ,that a treatment rate of 12,000 tonnes of tin concentrate per year could be obtained in a volatilization reactor 1·1 m in diameter and 6·1 m high. The process may have particular application to finely divided concentrates containing less than 20 per cent tin.

Jan 1, 1974

By R C. A Minnitt

This paper illustrates the use of variography and moving average plots as an aid to analysing variations in the process that can be used to direct the improvement efforts. The hydrometallurgical processes used in manganese metal production consist of sequential unit operations that include milling and reduction of manganese ores. Leaching of the reduced ore, is followed by solid-liquid separation, residue disposal, solution purification and electrowinning of manganese metal completes the process. The nearly 250 integrated process control loops rely on reports of pH, flow pressure, level, temperature and chemical analyses. Metallurgical accounting, reconciliation and process control is achieved through monitoring of the chemical and mass balances within the manganese reduction plant, requiring approximately 50 000 analyses of solids, powders and liquids each month. The largest numbers of samples are taken in the cell house. Changes and variations monitored by sample statistics ensure that the manganese products comply with predetermined specification limits. Optimising the information-value of the approximately 50 000 samples in the manganese plant is carried out in tandem with ongoing process optimisation. Variographic analysis of daily sampling data suggests that the cyclical behaviour evident in the moving average plots is only a reflection of random residual variability and not a reflection of true underlying variability related to cyclical phenomena. Low resolution in the variogram of daily sampling data masks the short-range variability that emerges when hourly data are analysed. Hourly samples collected over a 39-day period (giving 941 sample data), helped identify short-range cycles in the process. The relative distribution of variability for daily sample intervals, indicate that 57 per cent arises from V[0], 18 per cent from V[process] and 16 per cent from random residual variation. V[0] includes all the uncontrolled sampling error arising from a poor sampling protocol, the fundamental error (FE), the grouping and segregation errors (GSE), the delimitation error (DE), the extraction error (EE), etc. This confirms the suspicions regarding the suboptimality of the sampling protocol and the way it is implemented. The absence of long-term trends in the leach suggests that short-term variation (less than one day) dominates the process. While the control charts indicate that the overall processes are maintained above the lower specification limits and the target values, there is nevertheless a considerable amount of variability in the system that overhangs the processes and threatens to impact them negatively. Although the variability in the leach is above the prescribed limits, the volatility is a matter of concern because it seems to be uncontrolled. The comparison of the various sources of variability in data collected on an hourly basis suggests that the short-term random variability (V[0]) accounts for almost 50 per cent of the variability in the process. The main source of this variability is due to errors in the sampling protocol and is probably related to the size of the fundamental error (FE), the grouping and segregation errors (GSE), the delimitation error (DE), the extraction error (EE), etc. Remediation of FE and GSE will probably lead to a reduction in V[0], whereas V[process] could be mitigated by reducing the biases associated with DE and EE in particular.

Jan 1, 2008

By S. H. Brown

In our work as health physicists*, we do a lot of public speaking and interaction with the public on issues related to development of uranium mining and milling (?uranium recovery?) in the US. Understandingly, the public has important concerns about this. Accordingly, this paper is presented in a ?question and answer? format in which we have tried to capture what are some of the most common concerns we hear from citizens and address them. We have attempted to do so based on the best scientific information we have, representing information well documented in peer-reviewed scientific literature and consensus positions from both national and international scientific standard setting bodies and related committees. We have included some of the more important of these scientifically-based references to support the information provided. Practical space limitations prevent completeness in this regard in some cases. Visit the Health Physics Society?s web site or feel free to contact me directly for additional references, information or detail ? Steve Brown. The health physicist?s primary objective is to manage the beneficial uses of ionizing radiation while protecting workers and the public from potential hazards. For more information on what a health physicist is and on the Health Physics Society, visit the Society?s web site at www.hps.org.

Feb 23, 2014

By Gábor Csicsovszki

We have developed a novel method - at the laboratory scale - comprising an ion-exchange separation and a membrane-electrolysis step for the purpose of zero-waste regeneration of spent HCl pickling liquors originating from hot-dip galvanizing of common steels. It is aimed at the parallel regeneration of HCl and iron. Experiments revealed that iron can be electrodeposited at high current efficiencies by maintaining the following conditions: 0.04-0.08 M HCl, 500-1000 A/m2, 20°C and stationary electrolyte in a conventional cell. Zinc in the solution did not disturb the deposition of iron, however it contaminated the product and it poisons the anion-exchange membrane required to tackle acidity during electrolysis. For a preliminary separation, anion-exchange tests were carried out to produce pure iron solutions. Beyond the equilibrium studies, column experiments were carried out showing that low flow rates of the loading solution and the ~1.5 M HCl eluent are essential for separation.

Jan 1, 2006

St. Peter sandstone is very different from the minerals and rocks that have been studied extensively in mining. On the one hand, it is brittle as characterized by an unusually high friction angle and steeply curved failure envelopes. On the other hand, it is friable, possessing extremely low, and in most cases zero cohesion. The scarcity of the ground control techniques for this particular mining environment has created many difficulties for the mine operators. In order to resolve these problems, the geotechnical properties of the St. Peter sandstones were investigated through a comprehensive research program, which included uniaxial test, triaxial test, porosity test, thin section, X-ray diffraction (XRD), and scanning electron microscope (SEM). The specimens used for the uniaxial and triaxial tests were specially prepared because of the highly friable nature of the St. Peter sandstone. Thin section, XRD and SEM were utilized to examine the effect of the microstructure of the St. Peter sandstones on its strength characteristics.

Feb 27, 2013