Search Documents

By R. A. Jankowski, R. Gong, R. Bhaskar

Full-scale laboratory studies were performed to evaluate the effect of passive barriers and spray airmovers on airflow patterns at a continuous miner face and in reducing underboom boilout and operator exposure to dust. Tasks included baseline data collection, smoke trace tests, detailed performance testing using tracer gas, and data analyses. Data collection was performed using a state-of -the-art gas analysis system and custom-developed software. The data were used to calculate operator exposure at various locations and to develop gas profile maps to analyze airflow patterns. The effects of the proposed underboom airflow modification devices on operator exposure and airflow patterns were examined. Based on the results obtained from the study, the base case condition, with no barriers, appears to result in the lowest operator exposure.

Jan 1, 1992

By M R. Hettigner, J Nawrocki, C E. Johnson, P G. Cahill

This study evaluates the effects of both short inter-hole and intra-hole delay times on rock fragmentation and throw. Full-scale test blasts were analyzed at a granite quarry in Talbotton, GA. This analysis provides a representative understanding of timing effects on fragmentation in the field, different from previous lab scale studies that negate the effect of geology. Inter-hole delay times between 0 ms and 25 ms were tested on a series of 4 bench blasts and subsequently examined using photographic fragmentation analysis methods.

Jan 1, 2017

A small-charge rock excavation method based upon the Penetrating Cone Fracture (PCF) technique has been demonstrated to be capable of excavating the hardest of rocks. The PCF technique involves drilling shallow holes in the rock which are then pressurised at the bottom by a propellant charge device. A controlled fracture is initiated at the hole bottom comer and propagates in such a manner as to excavate the rock at an energy efficiency three to five times better than explosives. Due to the low flyrock velocities and airblast pressures realised with PCF breakage, the method may be used in close proximity to equipment and personnel and is thus ideally suited for integration into continuous hard rock excavation systems. Over the past 18 months full-scale testing of the PCF method has been carried out in mines in the US and Australia. This testing has utilised a 76 mm diameter gas injector for hole pressurisation and employed propellant charges ranging from 80 to 320 gm. In addition to extensive data on rock excavation performance, data on ground motion, dust, carbon monoxide and air blast have been obtained. These data indicate that none of the parameters associated with PCF breakage are detrimental to the development of PCF-based, continuous-excavation machines. Machines employing the PCF method may range from simple single-boom machines for secondary breakage and small precision-blasting jobs to integrated systems with several booms, continuous mucking capabilities and ground-support equipment for drifting and tunnelling.

Jan 1, 1993

By A Ross, B De Rivaz

The results of full-scale tests on precast segment made at University of Roma are presented. The segments were cast using fibre-reinforced concrete produced without any traditional reinforcement, by using fiber made in high-strength steel and a new type of anchorage.Bending tests were performed in order to check the bearing capacity of the segments under the flexural actions; these occur during de-moulding, handling, storage phases as well as in the in situ condition (due to asymmetric soil pressure). Furthermore, point load tests simulating the TBM thrust were performed, in order to study the construction phase (excavation).The results show that the segment response largely respects the material testing and design advice according to the Fib Model Code 2010. Providing engineers, precast operators and builders confidence in material strengths and design methodology.CITATION:De Rivaz, B and Ross, A, 2014. Full-scale tests on precast tunnel segments made in concrete reinforced with high-strength steel fibres, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 469–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Artak D. Mirzoyan

Pile foundations near the edge of a slope are often required to resist lateral loads. This is particularly important for piles at abutments of bridges. However, very few full-scale tests are available that compare the effect on lateral resistance of piles installed in sloping ground to piles installed in horizontal ground. To investigate the effect of a slope on lateral pile resistance, three full-scale lateral load tests were performed on an instrumented steel pipe pile. For the first test, the pile was laterally loaded in horizontal ground; in the second test, the pile was at the crest of a 30º downward slope; and for the third test, the pile was located three pile diameters from the crest of a 30º slope. The soil around the pile consisted of well-graded clean sand (concrete sand) and was compacted to 95% of the modified Proctor maximum unit weight in all three tests. Lab and in-situ direct shear tests indicated that the friction angle of the sand was approximately 39 degrees. The pile was instrumented with strain gauges so that the bending moment versus depth profile could be determined. Pile head load, deflection and rotation were also measured. Based on the load versus deflection curves, the presence of the slope resulted in a decrease in lateral resistance of about 20% for the pile at the crest of the slope and 8% for the pile at 3D from the crest of the slope relative to the pile in horizontal ground. The presence of the slope also resulted in an increase in the maximum moment of 29% and 20% for the piles at the slope crest and at 3 pile diameters from slope crest, respectively. Analyses using LPILE with the measured friction angle significantly underestimated the lateral resistance for the horizontal soil profile. After calibrating the model with the response of the pile in horizontal sand, analyses including the slope still underestimated lateral resistance by about 20%.

Jan 1, 2007

By Ambrose Buchanan, Rob Farnfield, Charles Adcock

Beginning on 7th September 1940 the City of London was subjected to 57 consecutive days of bombing in what became known as the ‘London Blitz’. To commemorate the 70th anniversary of this event a television series was commissioned that required the open detonation of World War 2 equivalent bombs close to purpose built structures constructed using period design and materials. The structures were built on a remote test facility in the North of England that is able to fire large quantities of explosive in the air.

Jan 1, 2011

By S. Moolla, R. Lynch, S. Brijraj

A reliable method to locate microseismic evets is an important objective for routine mine seismic monitoring. We developed an algorithm that can automatically and reliably locate an event from a single uniaxial trace. Signals created by microseismic events are recorded as seismograms that consist of direct P- and S-waves as well as the waves reflected off the underground excavations. We take advantage of the extra complexity these reflections introduce as they make the signal more unique. In our investigation we cross-correlated unaltered synthetic seismograms against trial waveforms created from a linear combination of appropriate waveforms from a library of numerically calculated strain Green’s tensors. We use a single uniaxial synthetic seismogram to invert for the source location, six moment tensor components, and frequency. The resulting cost functions are constructed as maximal correlations at each node in the mine grid through the true source x-planes. This function is maximized by differential evolution to simultaneously yield the source parameters. Sensitivity tests such as shifting the mine plans and altering the background velocities of the media are investigated to test the robustness of the method. We contaminate the data with 40% white noise to test the resolution against simulated real recorded seismograms. The method is demonstrated using synthetic data calculated with a realistic underground 3D velocity model.

Jun 10, 2024

By Sam H. Patterson

Fuller's earth and bentonite are two clay commodities that are interrelated either by mineral composition or use. Because of this interrelation and the sale of both for many different uses, some ambiguity in their classification has resulted. The term "fuller's earth" has no compositional or mineralogical meaning, and it is used more or less as a catchall for any clay or earthy material suitable for certain uses. Most, but not all, of these uses require absorbent properties. Bentonite by geologic definition must have formed from volcanic ash or tuff or the glassy material in volcanic rock; most bentonites consist chiefly of montmorillonite but other clay minerals may be present. In industrial usage the term "bentonite" is applied to any clay consisting chiefly of montmorillonite, irrespective of origin. Georgia and Florida have historically been the leading States in the production of fuller's earth; bentonite has been produced in Alabama on a small scale. The first major use of fuller's earth was in refining of oils. Other materials have replaced fuller's earth for this purpose to a major extent, but many new uses for fuller's earth have been found, and production has increased in recent years. The new uses include absorbent products, insecticide and pesticide carriers, drilling mud, and many others. The bentonite now produced in Alabama is of the "southern," "low selling," or "calcium" type and is used mainly as foundry-sand bond. Most of the fuller's earth mined now is in the Hawthorn Formation of Miocene age; a lesser amount is produced from the Twiggs Clay Member and other beds in the Barnwell Formation of Eocene age. Inactive pits from which fuller's-earth was produced from other formations occur at several localities. The bentonite now mined in Alabama is in beds of Cretaceous age; several years ago bentonite was produced from Eocene beds in this State.

Jan 1, 1972

By Randy Settgast, Daniel Moos, Hyunil Jo, Ghazal Izadi, Christine Baba

"Analyses of production logs of multiply fractured horizontal wells in unconventional plays show that only a small percent (~30%) of perforation clusters contribute to production. We present in this paper one possible approach to mitigating this problem, based on use of a fully 3-D numerical model of fracture propagation through a heterogeneous medium, by studying the influence both of spacing and of perforation friction on the initiation and propagation of simultaneous hydraulic fractures from a horizontal wellbore. The results indicate that while limited-entry perforating can help to equalize the lengths of fractures simultaneously growing from multiple clusters, it cannot equalize their widths. Both fracture width and fracture length can be equilibrated by combining non-even cluster spacing with limited-entry perforating. This has obvious benefits as it allows equalized placement of proppant across the entire series of perforation clusters, resulting in similar fracture widths and conductivities which enhances the likelihood that all clusters will contribute equally to production.INTRODUCTIONThere is substantial evidence from production logs and other information that during the hydraulic stimulation of horizontal wells, not all perforation clusters within a given stage will produce. One possible cause is the interaction between the hydraulic fractures emanating from each perforation cluster. Typically fractures created at the outer perforation clusters create “stress shadows”, i.e. increases in compressive stress in the minimum principal stress direction, which limit the growth of fractures growing from interior clusters; this is confirmed by modelling [1, 2, 3]. An example of this can be seen in Figure 1 which shows the final configuration of simultaneously propagating fractures from multiple, evenly spaced clusters when there is no perforation friction. The inner fractures are substantially shorter, reproducing the results by Bunger and Peirce [3]. The inner fractures also have substantially smaller widths.One approach to equalize the growth of simultaneously propagating fractures from a horizontal wellbore is by using limited-entry perforating as a method to equilibrate the flow rates into each of the different perforation clusters. Perforation friction is caused by the finite diameter of the entry points into the formation, and leads to a pressure drop across each perforation which is proportional to the flow rate squared. Fractures that take more fluid have a higher fluid velocity through the perforations than fractures receiving less fluid. This causes a larger pressure drop between the wellbore and more rapidly growing fractures, compared to the same pressure drop between the wellbore and the fractures that grow more slowly. Because pressure within the wellbore is approximately the same at each entry point, the larger pressure drop leads to less pressure being delivered to rapidly growing fractures, thereby decreasing their ability to propagate and reducing the amount of fluid they are able to receive. Because the mass rate of injection into the wellbore is constant, this forces more fluid into the fractures that were propagating more slowly, increasing their growth rate. It also increases the pressure required to drive fluid injection. The balance of these effects makes the system largely self-regulating and delivers more balanced fracture growth. While this effect is well known, it is often neglected in current numerical models."

Jan 1, 2015

By T. Nyakudarika

The Unki Platinum Mines concentrator, employing an MF2 circuit configuration which includes fully-autogenous primary milling of run-of-mine (ROM) ore, was commissioned in November 2010. The project was Anglo American Platinum?s first PGM concentrator in Zimbabwe and would form a significant contribution to the group?s platinum production. The project financials demonstrated that the project was operating-cost sensitive. After reviewing the metallurgical testwork, mineralogical examinations, and the history of similar operations, it became apparent that the Unki ore characteristics rendered it amenable to autogenous milling. The primary ball mill, structurally designed for 30 per cent steel load, could be operated at the required initial phase throughput with fully-autogenous primary milling, realizing savings in both power requirements and grinding media consumption. The original mill sizing had been done with fully-autogenous milling in mind, but allowing for flexibility and mitigation in case of varied mining fragmentation. Since attaining steady state, target grinds have been achieved. This paper looks at the Unki ore characterization programme, design considerations, and the operational and control philosophy for a successful comminution circuit, and discusses the design to produce a flexible, low opex, mitigated comminution and overall MF2 flowsheet that is easily expanded in line with the potential for optimum exploitation of the orebody.

Jan 1, 2012

By T. P. Weldum

INTRODUCTION Cleveland-Cliffs' operations in Michigan have been utilizing fully autogenous grinding for over four decades. This is but one of the key characteristics of the iron ore processing method that was developed for the extremely fine grained, low grade deposits of the region. Liberation size of the hematite and magnetite ranges from about 30 to less than 1 micron. Typical grinding fineness target to achieve silica grade in the concentrate is 80 to 90% passing 25 microns, or a P80 of approximately 20 microns. After primary grinding, the magnetite ore is first upgraded by rougher magnetic separation. It is then ground to final product size, sent through thickener-sizers utilizing selective flocculation, upgraded again by finisher magnetic separation, and then brought to final silica grade by reverse amine flotation. Hematite ore follows essentially the same route, less the magnetic separation stages. Concentrate is filtered and pelletized, along with con- trolled additions of fluxstone, to ready it for shipping. Iron ore pellets on the water of the Great Lakes have a value of approximately 1.5 cents per pound. GRINDING PROCESS DESCRIPTION Details of the Empire magnetite grinding process flowsheet have been presented by Greenwood and Rajala (1992), and more recently by Rose et al. (2002). The Tilden comminution process for either magnetite or hematite is essentially identical, with the exception of some variations in the excess pebble treatment methods (McIvor and

Jan 1, 2004

By R. K. McLimans, C. Knudsen, S. Bernstein, D. Frei

Computer Controlled Scanning Electron Microscopy (CCSEM) is used to analyze indivdual mineral fractions in heavy mineral sands. CCSEM is a fully automated particle analysis technique for the determination of physical and chemical properties of a large number of individual particles. CCSEM enables the precise and accurate determination of the modal abundances of individual mineral fractions (e.g. ilmenite, rutile, zircon, or garnet), their average chemical composition (and compositional variation), as well as their physical properties such as size (e.g. diameter and perimeter length) and shape (aspect ratio and circularity). A unique sample preparation procedure is used to produce representative polished sections from cylinders of raw sand samples such that thousands of grains are present in a polished cross section, but grains are not touching. The combination of this sample preparation technique with CCSEM enables the fully automated analysis of individual grains without the application of de-agglomeration or erosion steps to separate touching particles. Hence, CCSEM yields information representative of the entire area of analyzed grains without systematic bias due to neglect of rim areas by de-agglomeration or erosion steps. Therefore, the resulting data are determined with high accuracy, precision and statistical validity. Because the sample preparation is relatively straightforward, using raw sand samples, and all chemical and physical properties are determined in one analytical session per sample, CCSEM is a powerful cost and time efficient tool for characterizing chemical and physical properties of minerals in heavy mineral sand deposits.

Jan 1, 2005

By B. J. Coetzee, P. W. Sonnendecker

The quality control of a two-stage coal washing process involves several complex components that need to be modelled accurately, to enable autonomous control of the process. The first objective is to develop a method to track the material through the washing process, while ensuring accurate washing prediction models are used. This was achieved through a digital twin model of the Grootegeluk 1 coal processing plant. The model is the amalgamation of manipulating and combining of data-sets from the plant historian, geological wash tables, and mining dispatch servers. This information is then used to control and set the processing medium densities of all 15 modules on the plant, 10 modules in the primary wash and 5 modules in the secondary wash. This controller has been successfully implemented and controlled the plant for 10 days.

Aug 2, 2022

A completely automated primary crusher is now in operation at Kaiser Steel Corp.'s Eagle Mountain, Calif., iron mine. The word "completely" is italicized to underscore its literal meaning- automation so thorough that even the control room for the crusher does not require a man to watch the flickering dials and lights. The automation of the unit is such that its operation, including starting and stopping, are controlled from the secondary crusher station. The crusher-a Symons 60-in. gyratory which can handle 3600 tph-features built-in safety devices that will turn the crusher off if oil pressure drops, if oil overheats, if bearing temperatures exceed permissible limits, or if parts of its electronic brain fail. According to reports, the worst that can now happen is a plugging of the crusher.

Jan 6, 1963

By Y. H. Hatzor

ABSTRACT: A fully dynamic, two dimensional, stability analysis of a highly discontinuous rock slope is demonstrated in this paper. The studied rock slope is the upper terrace of King Herod’s Palace in Masada, situated on the western margins of the seismically active Dead Sea Rift. The dynamic deformation of the slope is calculated using a fully dynamic version of DDA in which time dependent acceleration is used as input. The analytically determined failure modes of critical keyblocks in the jointed rock slope are clearly predicted by DDA at the end of the dynamic calculation. It is found however that for realistic displacement estimates some amount of energy dissipation must be introduced into the otherwise fully elastic, un-damped, DDA formulation. Comparison of predicted damage with actual slope performance over historic time span window of 2000 years allows us to conclude that introduction of 2% kinetic damping should suffice for realistic damage predictions. This conclusion is in agreement with recent results of Tsesarsky, Hatzor and Sitar (2002) who compared displacements of a single block on an inclined plane subjected to dynamic loading obtained by DDA and by shaking table experiments. Using dynamic DDA it is shown that introduction of a simple rock bolting pattern completely stabilizes the slope. RÉSUMÉ : On présente dans cet article une analyse bidimensionnelle complète de la stabilité d’une pente rocheuse très fracturée. La pente rocheuse étudiée est la terrasse supérieure du Palais du roi Hérode à Massada, située sur la rive Ouest du Rift sismiquement actif de la Mer Morte. La pente est constituée de blocs de dolomite raide présentant une stratification sub-horizontale et des joints sub-verticaux. La déformation dynamique de la pente est calculée en utilisant une version entièrement dynamique de l’Analyse de Déformation Discontinue (DDA) où l’accélération dépendant du temps est utilisée comme donnée. Les modes de rupture déterminés analytiquement des blocs clés dans la pente rocheuse fracturée sont clairement prévus par l’approche DDA à la fin du calcul dynamique. On trouve cependant, que pour obtenir des estimations réalistes du déplacement, il faut introduire un facteur de dissipation énergétique sans lequel la formulation DDA serait totalement élastique et sans amortissement. En comparant l’endommagement prévu avec les caractéristiques de la pente sur une période historique de 2000 ans, nous pouvons conclure que l’introduction d’un amortissement cinématique de 2% suffit pour obtenir de prévisions réalistes. Cette conclusion est conforme aux résultats récents de Tsesarsky, Hatzor and Sitar (2002) qui ont comparé les déplacements d’un bloc isolé sur un plan incliné sous chargement dynamique obtenus avec l’analyse DDA et à partir d’essais sur table vibrante. ZUSAMMENFASSUNG: En utilisant une modélisation DDA dynamique on montre que l’introduction d’un système simple de boulonnage stabilise la pente.In dieser Veroeffentlichung wird eine vollstaendig dynamische, zweidimensionale Stabilitaetsanalyse eines hoechst diskontinuierlichen Steinhangs dargestellt. Der untersuchte Hang ist die obere Terrasse des Herodespalastes in Massada, welche in den westlichen Randgebieten des seismisch aktiven Toten Meer Grabens liegt.Die dynamische Deformation des Berghangs wird mit Hilfe einer vollstaendig dynamischen DDA-Version berechnet, in welcher als Input die zeitabhaengige Beschleunigung eingegeben wird. Die analytisch bestimmten Versagensarten kritischer Schluesselbloecke in diesem zerkluefteten Steinhang werden durch Anwendung von DDA am Ende der dynamischen Berechnung klar vorausgesagt. Es zeigt sich jedoch, dass fuer realistische Dislozierungs-Abschaetzungen ein gewisses Mass an Energieverlust in der sonst vollstaendig elastischen, ungedaempften DDA-Fassung einbezogen werden muss. Der Vergleich des vorhergesagten Schadens mit dem aktuellen Verhalten des Berghangs waehrend einer historischen Zeitspanne von 2000 Jahren erlaubt uns zu schliessen, dass ein Zusatz von 2% kinetischer Daempfung fuer eine realistische Vorhersage des Schadens ausreichen sollte. Diese Schlussfolgerung steht im Einvernehmen mit neuen Ergebnissen von Tsesarsky, Hatzor und Sitar (2002), welche die Dislozierung eines einzelnen Blocks auf geneigter Ebene unter dynamischer Belastung – unter Anwendung von DDA und “shaking table”-Versuchen – verglichen. Mit Hilfe der dynamischen DDA wird gezeigt, dass der Steinhang durch Anwendung einer einfachen Steinschraubenstruktur vollkommen stabilisiert werden kann.

Jan 1, 2003

By John Kucish

Roof bolting in the Pittsburgh Coalbed takes many forms today: coupled partially grouted bolts, fully grouted rebar, passive cable bolts, tensioned cable bolts, and torque tension rebar. The Federal No. 2 Mine of Peabody Energy has recently made a significant advance in longwall headgate primary roof support, with the change fiom an 8 ft long coupled partially grouted bolt to a 6 ft long torque tension system. The coupled partially grouted bolt consists of a 4 ft long 0.804 in diameter rolled deformation bar thread coupled to a smooth 718 in headed bar. The coupled partially grouted bolt is anchored into a 1 318 in borehole with 4 ft of high speed resin. The 718 in diameter smooth bar is tensioned by rotation into the treaded coupler, upon setting of the resin, compressing the immediate roof. The change was initially driven by occasional failure of the coupled partially grouted bolt at the threaded coupler, due to lateral movement caused by horizontal stress. A fully grouted % in diameter torque tension bolt, in a 1 in borehole, was proposed as a cost effective primary bolting for the high horizontal stress conditions. The upper 2 112 ft of the rebar is anchored in fast set, medium viscosity resin and the bottom 3 K ft is anchored in slow set, special low insertion force resin. The lower end of the rebar is threaded with a nut that permits the counter clockwise spinning of the bolt to mix the resin, at maximum rotational torque. Upon setting of the high speed top resin, the nut is spun clockwise to tighten the nut against a metal dome plate. The plate is forced against the roof to compress the immediate roof, A complete headgate entry has been successfully supported with the torque tension system. The mining of the adjacent longwall panel was completed in September 2004. The torque tension system provided a 25% savings over the previously employed coupled partially grouted bolt system.

Jan 1, 2005

By M Ahler

Future developments in the mining sector will be driven by the need to increase safety, ecological sustainability and efficiency. Autonomous systems represent a huge step towards achieving these goals. This paper describes the basic infrastructure of an autonomous system – essentially a network of distributed sensors. Although the sensors are distributed, the overarching communication network with its related middleware offers a transparent and uniform layer. This middleware acts as an abstraction layer which priorities information and provides information to other platforms on request. This permits higher-level autonomous functionality to utilise all information available in the system regardless of where data has been generated or via which physical communication link it has been processed.The Personnel Proximity Detection (PDD) system is described in detail as an example, with details not only of the system itself, but also of the essential full integration and how the abstraction layer allows this technology to be plugged in at any location of the network. The paper ends with a summary of the content and a conclusion.

Nov 22, 2011

By S. Tu, Y. Yuan, H. Wei, Z. Chen, M. Jia

"To reduce production costs and increase efficiency in ageing coal mines, a system that utilizes two shearers in a fully mechanized longwall working face is proposed. Using theoretical and engineering experience, three issues pertaining to the system were determined: (a) the two-shearer mining technique; (b) matching and modifying the equipment; (c) and coal-cutting task allocation for each shearer. Two mining processes are proposed, with the two shearers travelling in either the same or opposing directions. To avoid breakage of chains and pan extrusion of the armoured face conveyor (AFC), the length of the AFC ‘snake’ was controlled. To ensure continuous cutting and transporting of coal, the cross-sectional dimensions of the AFC were checked and the shearer closer to the head drive was modified. Based on the assumption of equal cutting times for each shearer, the meeting position of the two shearers was obtained by using a theoretical model of mining task allocation. Application of this technique at No. 2 Jining Mine, China, has shown remarkable benefits: daily production capacity was increased by 54% and personnel efficiency was improved by 33 t/d per person. IntroductionAll coal mines aim to increase the unit output of the working face to reduce mining costs and improve the economic efficiency of the operation. To achieve this goal, a production model known as one mining face of the mining area has been adopted by most Chinese coal mines (Hu, Meng, and Zhu, 2008; Zhang, Zhang, and Wang, 2000). Under these conditions, the main technical approaches to maximize the output are increasing the width of the working face (Qu, Xu, and Xue, 2009) and accelerating the advancing speed (Robbins, 2000). In coalfields with shallow seams, the width of a fully mechanized face exceeds 300 m (Ju and Zhu, 2015; Fu, Song, and Xing, 2010); in coalfields with deep seams, the width of the face is usually greater than 240 m (Liu et al., 2016; Li et al., 2013). The term ‘super-long working face’ was proposed to describe working faces with a width of over 240 m (Zhao and Song, 2016; Xu et al, 2007) in China. To support these long working faces with rapid advancing speeds, high-powered mining equipment is required (Kulshreshtha and Parikh, 2001, 2002; Tu et al., 2009; Mishra, Sugla,and Singha, 2013). This is easily achieved in newly built mines, but is not a good choice for ageing mines because of the low return on a high investment on account of the limited remaining resources. It is therefore difficult for ageing mines to significantly increase their unit output with the existing mining equipment. This study focused on this problem: two shearers were applied to a longwall fully mechanized working face (LFMWF) to achieve increased unit output."

Oct 1, 2018

By Hiromu Kusakawa, Tetsuo Kanematsu

INTRODUCTION In urbanized area with heavy street traffic and with environmental requirements to lessen construction noise and vibration, the cut-and-cover is not always a feasible method to build a small diameter tunnel for sewage, water or other utilities. That is where the use of the shield machine to bore such a small diameter tunnel should be considered as a more acceptable alternative. Although the shield machine of this type should be small enough to meet specific requirements for a given tunnel, it should be big enough to provide some working space inside of the tunnel. Recently, we have successfully developed the fully mechanized small diameter tunneling method which enables us to bore a tunnel as small as 600mm in finished diameter. This paper discusses the concept of this newly developed method, including a case history where sewage tunnels of 800mm finished diameter were constructed by using this method. OUTLINE OF METHOD Developed from the original slurry shield pipe-jacking tunneling method, this method is highly automated so that all operations inside of the tunnel can be remotely controlled. Various data including the advance rate, position and inclination of the shield are transmitted to the central control room outside of the tunnel and monitored by the CCTV and the instrument panel at all times to

Jan 1, 1981

By Carlo Grandori

Foreword In loose ground and soft rock formations, mechanical tunnel boring is necessarily dependent on the adoption of shield machines and the application of adequate support or lining structures. These structures are erected either within or immediately behind the rear portion of the shield and provide the required reaction to the forward thrust. In competent rock formations where systematic support is not a requirement, hard rock tunnel boring machines generally advance by thrusting from a structure gripped against the tunnel walls. These machines may feature a more or less extended cutterhead shield or roof support, but when in weathered, fractured or otherwise weakened ground, or in fault zones filled with soft gouge, the gripper mechanism often cannot provide enough thrust reaction to advance the cutterhead. Under these conditions, early support of the arch and walls is generally required in the form of rock bolts, steel rings and laggings and some times of a primary concrete lining placed in the short section between cutterhead and grippers. Such tunnel support measures generally fail to produce an adequate increase in thrust reaction capacity, but

Jan 1, 1976