Search Documents

By J. Linhart

In vertical airways, falling material - solids-or water - may cause undesirable disturbances in the ventilation in the airway itself and also in neig¬bouring airways unless precautions are taken to stabilize the air flow. Such cases can occur, for example, - in shaft sinking by drilling from a pilot hole, - during the filling up of shafts, and - during the introduction of water into shafts in the case of mine fires. In an airway with upward ventilation the falling material will reduce the air flow and may even re¬verse its direction. In an airway with downward ventilation the air flow can only increase, but a reversal of the direction of ventilation may result in a parallel airway. These disturbances in the normal ventilation are undesirable as it must be the aim to have ventilation that is stable in quantity and direction throughout a mine. In order to be able to prepare suitable stabilization measures one must know the pressure generated by the falling material; this pressure will henceforth be called "aeromotive" pressure. The main factors determining the influence of falling material on the ventilation are - the amount of falling material and its height of fall, - the cross sectional area of the airway, - the pressure. difference prevailing in it, - the-position of the. airway in the ventilation. network, - the air velocity, and - other parameters, e. g. the density and grain size of the falling material. To determine the aeromotive pressure-measurements have been made underground during the sinking and filling of shafts and systematic studies have been carried out during the supply of water into a staple shaft. The present paper deals first with some fundamental theoretical considerations and then describes the measuring arrangements and the results of the series of experiments that have been carried out.

Jan 1, 1980

By L. M. Demers, D. C. Kuhn

It has been suggested that radicals on the surface of dust particles are key chemical factors in the pathophysiology that results from the occupational inhalation of coal and silica dust. In addition, oxygenated derivatives of arachidonic acid (eicosanoidsJ have been implicated as important biochemical mediator5 of mineral dust-induced lung disease through their role in bronchial and vascular smooth muscle reactivity, inflammation, and fibrosis. Therefore, we assessed eicosanoid production by the rat alveolar macrophage (AM) exposed in vitro to mineral dusts with varying surface chemical characteristics in order to determine if radicals associated with the mineral dust could influence the production of proinflammatory mediators in the lung environment. Primary cultures of rat AM were exposed to freshly fractured or "stale" bituminous coal dust, as well as untreated silica or silica calcined to 500 and 1100°C. Prostaglandin E1 (PGE;V, thromboxane Ai (T}(Ay, and leukotriene 84 (LTB; levels in incubation medium were determined by specific radioimmunoassay. When AM were exposed to freshly fractured coal dust, PGE2 production was markedly increased. In contrast, exposure of AM to "stale" dust significantly reduced PGE1 production. Exposure of AM to freshly fractured coal dust resulted in a significant increase in production by AM, while exposure to stale coal dust did not influence AM TXA1 production. Neither "fresh" nor "stale" coal dust had any effect on LTB4 production. In vitro exposure of AM to untreated silica resulted in a significant increase in TXA1 PGE.,, TXA; and LTB4 production compared with control. However, exposure of AM to silica calcined to 11oo•c resulted in eicosanoid levels that were not significantly different from control. These effects were still apparent 8 wk after calcination of the silica particles. Silica was a more potent activator of AM eicosanoid production than was coal, and amorphous fumed silica was a more potent activator of AM eicosanoid production than was crystalline silica. These findings suggest that radicals associated with respirable coal and silica particles may play a key role in the ability of mineral dust to activate AM eicosanoid production and therefore may be important in the pathophysiological consequences of occupational mineral dust inhalation.

Mar 1, 1992

By L. M. Demers, D. C. Kuhn

The alveolar macrophage (AM) responds to stimuli such as coal mine dust by releasing inflammatory mediators such as cytokines, growth factors. reactive oxygen species. and eicosanoids. Eicosanoids are synthesized by°AM through the action of cyclooxygenase and lipoxygenase enzymes and serve to modulate the proinflammatory function of this cell as part of the lungs' host defense mechanism. Reactive oxygen species can be generated by AM as a by-product in the biosynthetic pathway of the prostaglandins. AM produces primarily prostaglandin E2, thromboxane A2, and leukotriene B4 as part of the cellular response to an inflammatory stimulus. There is evidence to suggest that eicosanoid production by AM is functionally linked to both surface interaction with mine dust particles like silica and by the phagocytosis of the dust particle itself. In this report, we examined the effects of an antioxidant, vitamin E. on dust-induced synthesis of PGE2 and TXB2 in vitro and in vivo by AM obtained by bronchoalveolar lavage from rats. We also looked at the effects of the surface of silica particles on AM eicosanoid biosynthesis under conditions of calcination, a process that removes exposed hydroxyl groups from the surface of silica particles, thus reducing the likelihood of soluble hydroxyl radical formation. Treatment of AM with vitamin E in vivo and in vitro reduced the augmentation in eicosanoid production usually observed when AM are exposed to mine dusts. These results suggest that vitamin E may effectively reduce the inflammatory and fibrotic response produced by inhalation of mineral dust through an antioxidant mechanism. Silica that has been chemically altered by calcination was unable to activate AM eicosanoid production in vitro when compared to untreated, freshly fractured silica. These findings suggest that the mechanism by which dust particles can activate AM eicosanoid release may involve interaction of surface and/or soluble factors with the cell membrane. Taken together, these studies point to the involvement of AM eicosanoid production as part of the proinflammatory response of this cell to occupational inhalation of mineral dust. - Environ Health Perspect 102(Suppl 10):97-100 (1994)

Dec 1, 1995

By V. E. Vigdergauz

Possibilities of the analysis of potential energy of bubble-particle interaction on the basis of extended DLVO theory are discussed. Interaction energies of mineral silica, coal and pyrite particles with contact angles from 20 to 100 degrees and air bubbles in neutral and alkaline solutions are analyzed. It is shown that for hydrophilic silica, the formation of particle-bubble complexes (either in the area of primary or secondary potential minima) is impossible due to the high potential barriers (from 6000 to 140000 kT)and low values of the attraction force. There is shown that for coal and pyrite particles the energy of interaction vs. particle-bubble distance strongly depends on pH value. Improvement of floatability of minerals by the hydrophobization of their surface by collectors leads to the eliminating of potential barriers and the formation of the stable complexes of minerals and air bubbles in the area of primary potential minimum. In addition, due to hydrophobization of coal and pyrite changing pH has practically no influence on the energy of interaction. There are discussed results of the numerical calculations of normalized interaction forces in particle-bubble systems on the nanometer distances for pyrite, sphalerite, and chalcopyrite at contact angles up to 85° in comparison with the experimental data. The values of adhesion force for hydrophobized particles of coal and pyrite to air bubbles are about 10-5 N, that indicates stability of the formed flotation complexes. Examples of using the long-range and high-energy effect of hydrophobic interactions for improving minerals floatability are discussed. There are illustrated minerals wettability changes induced by the adsorption of thiol collector and hydrophobic polymer. Possibilities of flocculation and flotation of mineral slimes due the polymer-collector hydrophobic interactions are shown. Keywords: bubble-particle interaction, contact angle, extended DLVO theory, floatability

Sep 1, 2012

By Sheng-li Wu, Guo-liang Zhang, Bo Su

The mineralogical characteristics of iron ores can influence their high temperature sintering performance. In this study, eight iron ore samples from Brazil, Australia, and South Africa were characterized by their chemical composition, mineral types, particle morphology, and gangue dispersity. Meanwhile the influence rules between the mineralogical characteristics and the high temperature characteristics were evaluated and analyzed. The results showed that the effect of SiO2 on assimilation characteristic of iron ores was relatively complex, Al2O3 and LOI of iron ores had negative correlation with assimilation temperature of iron ores, the dense slab-flaky mineral granule restrained to the assimilation characteristics of iron ores; liquid phase of iron ores with high SiO2 content and low Al2O3 content had high fluidity, and the higher dispersity of gangue minerals in iron ores was good to the fluidity of liquid phase.

Jan 1, 2015

By and Heather E. Lawson, Mark K. Larson, Gabriel Walton

In this study, we evaluated the effects of different shapes and distribution densities of mineral grains in coal on failure mechanics using the numerical software 3DEC. The main aim of this study was to identify possible failure mechanisms influenced by mineral habit and frequency in coal. Exploring differences in failure mechanics associated with the mineral grains helped to determine the role of mineral character as a possible contributor to characterize burst-prone coals. To achieve the goal of this study, a series of numerical specimens were prepared in the 3DEC model as follows: first, the 3DEC modeling in conjunction with the DFNs (Discrete Fracture Networks) technique was performed to explicitly generate the discontinuities (i.e., cleats and bedding planes) in the numerical specimens based on the results of laboratory analyses. Then, the different realizations of mineral grains were embedded in the 3DEC model to simulate an unconfined compressive strength (UCS) test to assess the influence of the mineralogical characteristics on the UCS.

By Xun Hu, Jian Pan, Hongbin Yu, Deqing Zhu, Yanhong Luo

Lump ores are one kind of important burdens for blast furnace (BF), their metallurgical properties have significant influence on BF performance. In this paper, the relationships between the mineralogy of five natural lump ores and the metallurgical performance have been studied. The mineralogy study includes mineral compositions, microstructure and porosity, and the metallurgical performance covers reducibility index (RI), low-temperature reduction degradation index (RDI) and decrepitation index (DI). The results show that the complex lump containing hematite, and goethite has better overall metallurgical performance. For single lump, the RI of goetihte ores is higher, the RDI and the DI is strongly influenced by porosity. The hematite and magnetite ores have good anti-decrepitation and anti-RDI, but generally the RI is lower due to lower porosity, and the RI is related to the grain size, the smaller grain size is, the better reduction will be.

Jan 1, 2015

By G. Lafont

Aug 1, 2013

By D. Elsworth, M. Bai

The influence of mining on the hydro-geo-mechanical environment can be greatly modified by alternating mining geometries. The limiting magnitudes of surface subsidence and groundwater flow over the mining area, as a result of mine geometric changes, can be reasonably predicted through the coupled finite-element model introduced in this paper. The model has been verified using real and conceptual case studies which reveal that changes in strata conductivities are strongly related to the strata deformation induced by mining. The greatest modification of hydraulic conductivities occurs within the caving or severely fractured zones. The study indicates that narrowing the panel face width will substantially reduce both the intensity and extent of mining damage to the overlying strata, limit surface subsidence and constrain the change in hydraulic conductivity to a reduced scale and smaller extent, particularly as mining depth increases.

Jan 1, 1995

By M. Bai

The influence of mining on the hydro-geomechanical environment is greatly constrained by alternating mining geometries. The limiting magnitudes of surface subsidence and groundwater flow over the mining area, as a result of geometry changes, can be reasonably predicted through a coupled finite-element model introduced in this paper. Verification of the model has been tested using real and conceptual case studies which reveal that changes in strata conductivities are strongly related to the strata deformation induced by mining. The greatest modification of hydraulic conductivities occurs within the caving or severely fractured zones. The study indicates that narrowing the panel face width will substantially reduce both the intensity and extent of mining damage to the overlying strata, limit surface subsidence and constrain the change in hydraulic conductivity to a reduced scale and smaller extent, particularly as mining depth increases.

Jan 1, 1993

By Guanghui Li, Xuling Chen, Zhiyun Ji, Min Gan, Tao Jiang, Xiaohui Fan, Zhiyuan Yu

With the increase of proportion of biochar(without modified) replacing coke breeze, the physical strength of sinter decreases due to the faster burning speed of biochar. An investigation upon passivating biochar with boric acid was then conducted to strengthen sintering in this paper. A layer of thin film of B2O3 distributed in the surface of biochar was observed, which could reduce the contact between reaction gas and biochar. So the burning speed of biochar was decreased properly after passivation, and the combustion efficiency increased due to the inhibition of carbon gasification. The comprehensive effects of above changes could increase the maximum temperature of sintering bed, which facilitated to the mineralization of sintering mixtures. Eventually sintering indices got reinforced. Thus the indices of sinter as applying 40% passivated biochar were comparable with that of 100% coke breeze.

Jan 1, 2015

By B. Tougas

Recycling of titanium represents an important economic activity due to high cost of the material and the amount of returns of machined parts which represent the bulk of finished titanium products (typical "buy to fly" of 10 in the aeronautic industry). In the present work, the metallurgical quality of 76 mm in diameter and 20 cm ingots poured in coated graphite mold will be assessed against the nature and condition of application of 4 coatings namely aluminum oxide, yttrium oxide, zirconium oxide and zirconium oxide with 4% aluminum oxide. The metallurgical quality has been evaluated in terms of alpha case thickness, microstructure and composition. Microhardness from surface will be assessed against casting conditions. Least square regression analysis have been use to optimize casting conditions.

Jan 1, 2011

By L. O. Filipov, N. E. Menad, A. Geneyton

"Zeta potential of synthetic monazites presenting various compositions were measured to investigate the effect of the main lanthanides substitutions on electrophoretic mobility and resulting IEP. The measurements are performed in a CO2 depleted and enriched solutions showing both reduced influence of monazite chemistry and strong influence of ions resulting from the solubilization and dissociation of CO2. The influence of oleic acid on the electrophoretic mobility of those monazites was also investigated. The influence of pH on oleate adsorption was studied using a bubble/particle adhesion system. Adhesion strength measurements were performed on pure synthetic monazite-(Ce) and monazite-(La). An extensive thermodynamic model of monazite in water was developed to highlight correlations between lanthanides hydroxides/carbonates species concentrations in the bulk solution and oleate adsorption. Based on electrophoretic measurements, advanced thermodynamic consideration and adhesion measurements, further details of the oleate adsorption model on monazite surface were proposed.INTRODUCTION Electrophoretic and potentiometric data on monazite and, a fortiori, other rare earth semi-soluble salts such as bastnaesite are extremely erratic (Chelgani et al. 2015). The isoelectric points measured with electrophoretic mobility methods range from 4.7 to 6.5 although sporadic data indicates an IEP (isoelectric point) far from that range. Different explanations are proposed in the literature to explain the IEP variability notably the numerous chemical substitutions that frequently occurred within monazite crystal lattice (Chelgani et al. 2015). Based on lanthanides speciation diagram, several authors highlighted the influence of specific lanthanide species on the flotation performance of rare earth semi-soluble salts when carboxylate or hydroxamate collectors are used. Although lanthanides ions have a great affinity for carbonates groups (Kragten et Decnop-Weever 1987), lanthanide (hydrogen) carbonates were not implemented in speciation diagrams. In this work, an advanced thermodynamic model is proposed to highlight correlation between flotation performance and lanthanide species predominance but also concentrations. Qualitative measurement of the monazite surface hydrophobicity are performed through tests of adhesion of coarse monazite particles onto bubbles. Since flotation and microflotation technics are highly influenced by hydrodynamic parameters, this method was investigated to obtain a sharp contrast between appropriate and inappropriate pH conditions. This paper is to investigate 1) the effect of lanthanides substitution on monazite surface properties through zeta potential measurements, 2) the mechanism of adsorption of carboxylates on monazite surfaces and 3) the effect of CO2 on monazite surface properties and carboxylates adsorption."

Jan 1, 2018

By Scott C. Brown, Brij M. Moudgil, Ivan U. Vakarelski

The manipulation of the apparent hydrophobicity of particlute surfaces is necessary to achieve optimal selectivity in flotation processes. Previously a number of works have investigated the role of microscale surface and particulate morphologies on chemically modified substrates. These works have suggested that microscale surface asperities lead to an increase in flotation efficiency by assisting in the rupture of wetting films. Yet, in mineral processing the presence of surface asperities may lead to a reduction in flotation. The reason for this may-in part-be due to the presence of nanoscale irregularities at the interface. In this work, it is proposed that the presence of roughness at the nanoscale may have a dominant impact on the apparent hydrophobicity of mineral surfaces during flotation. It is suggested that as inter-asperity seperation distances are reduced capillary effects are enhanced for high energy mineral surfaces leading to the formation of liquid domains, which adversely impact hydrophobicity. In addition, as these distances approach the surfactant headgroup size obstruction of surfactant self-assembly process may occur, thereby further limiting flotation.

Jan 1, 2003

By Scott C. Brown, Ivan U. Vakarelski

The particles commonly encountered in mineral benefication schemes have irregularites that are expressed at many different length scales. In part, this originates from preceding processes (e.g. makedown, comminution, handling and storage), which are known to chemically and physically modify the bulk particle and its surface. Interparticle tribology, dissolution and reprecipitation events along with large-scale mechanical stresses are just a handful of the interactions encountered during processing of particles prior to separation. It is feasible to imagine that each one of these events may impose a fingerprint of characteristic nanoscale, microscale, and macroscale morphological changes that can modify the overall interaction of these particles within a system. Suprisingly there are just a few works on how these resulting features can alter the performance of benefication schemes, and especially flotation.

Jan 1, 2003

By S. C. Brown

A number of studies have suggested that microscale asperities enhance bubble-particle attachment efficiency; however, in practice the roughening of particulate surfaces can also lead to a decrease in flotation. In the present investigation, it is proposed that nanoscale asperities may be partially responsible for this phenomenon. It is suggested that as inter-asperity separation distances are reduced capillary effects are enhanced leading to the formation of stable liquid domains, which adversely impact bubble-particle adhesion. In addition, obstruction of surfactant self-assembly may occur, further limiting flotation.

Jan 1, 2003

By Migen Dibra

Antitrust and competition laws are designed to protect the free markets and promote competition in order to assure a dynamic and efficient economy and to provide competitive prices for quality products and services. They apply to mergers and acquisitions as well as to joint ventures especially among competitor companies who possess market power and these include collaborations on research and development. If it is determined that these actions are likely to substantially prevent or lessen competition the courts might dissolve, stop, alternate them, etc. Two new factors affect this process today: The role of new technologies and the markets globalization. They both have a considerable effect on the way these laws are interpreted by the courts and on their eventual amendments in order to reflect the new reality. A new applied technology and the globalization separately or together may change the factors that determine how anticompetitive a merger or acquisition between competitors may be and may also serve as a basis for amending the antitrust and competition laws. In this paper, a short review of the recent mergers and acquisitions of various companies has been carried out along with an abridged analysis of the current antitrust and competition laws in USA, Canada and European Union in the view of their capacity to handle the new reality. Some related court decisions are also examined and several examples are given in order to illustrate the influence of new technologies and globalization in interpreting the existing laws and on their amendment possibilities.

Jan 1, 2006

By L. Cornish, P. A. Olubambi, J. H. Potgieter

Four 22%Cr series duplex stainless steels alloys containing varying nickel contents of approximately 5, 7, 9 and 13% were melted in a vacuum induction furnace, hot rolled, solution annealed and water quenched. Their corrosion behaviour was investigated in sulphuric acid and sodium chloride solutions using a potentiodynamic polarization technique. Increasing nickel contents have appreciable influence on their corrosion behaviour. Polarization curves show similarities in the uniform corrosion behaviour of the alloys in the solutions and a significant difference in their pitting behaviour in chloride environments. Alloy 2209 generally exhibited highest resistance to uniform corrosion while 2213 displayed distinct and best pitting corrosion resistance. Their corrosion behaviour were attributed to the influence of nickel on phase modification, microstructural refinement, and the probably types of films formed in different environments. Keywords: Duplex stainless steel; Nickel; Microstructure; Phase modification; Corrosion

Jan 1, 2006

By Shun-ichi Satoh

STUDIES by many authorities have proved that nitrogen exerts an injurious influence upon iron and steel, but in the casehardening of steel by carbon, nitrogen has the advantage of accelerating the process of cementation. Its influence upon special steels is quite remarkable; it can produce the hardest layer ever known in metallurgical products-a fact hit upon by A. Fry and studied and ascertained by L. Guillet. As there have been very few investigations on the influence of nitrogen on special steels, the writer has listed important articles dealing with this problem and has conducted experiments on nitrification. He also has tested the influence of nickel upon the penetration of nitrogen in electric-arc welding.

Jan 1, 1929

By Rikiya Kamezawa, Rudiono, Manabu Takeuchi

"Schottky type solar cells based on phthalocyanine (Pc) thin films were fabricated, and their photovoltaic performance was investigated in various ambient atmospheres. Most of cells prepared in this study showed a good rectification and photovoltaic effects in the visible wavelength region. The introduction ofN02 gas into the measuring chamber was confirmed to increase the current both in dark and under light illumination. However, chemical reaction between the Al electrode and N02 formed some oxide and deteriorated the Schottky barrier, resulting in an increase in cell resistivity. SF 6 gas also showed similar effects on the cell performance.IntroductionPhthalocyanine is one of the typical organic semiconductors, which shows high photoconductive sensitivity in the visible to infrared region. Today, several kinds of metal phthalocyanines are used in electrophotographic photoreceptors. In addition, application of phthalocyanines to solar cells have also been trying by many workers [1, 2]. Many efforts have been made for improving performance of phthalocyanine solar cells by modification of device structure [3, 4], doping by dye or pigment [5, 6] and incorporation of metal clusters [7]. It is known that electrical conductivity in phthalocyanine is increased by adsorption ofNO2 [8, 9]. We tried to improve photovoltaic performance ofphthalocyanine solar cell by adsorption ofNO2. This paper describes the influence of N02 adsorption on the photovoltaic behavior of phthalocyanine solar cells."

Jan 1, 2000