Search Documents

By H. R. Ogden, E. S. Bartlett, A. G. Imgram

THE tensile and notch tensile ductile-to-brittle transition characteristics of several refractory metals and alloys have been well documented.1-3 Electron-beam melted tantalum and columbium have been shown to retain excellent ductility at very low temperatures. Some indications of brittle behavior (low ductility and cleavage fracture) were observed with columbium tested at -253oC, but no similar effects were noticed with tantalum. Increasing the interstitial oxygen content in these two materials resulted in the detection of indications of brittle behavior at higher temperatures, although good ductility was retained in both bases at -196°C when they contained about 1 at. pet 0. Detailed descriptions of the impact transition behavior of these two materials at various purity levels have not been available. This technical note describes the effect of interstitial oxygen on the impact properties of wrought, fibered tantalum and columbium and compares the transition behavior to the previously determined tensile transition characteristics. Tantalum and columbium impact specimens with three different interstitial oxygen levels indicated in Table I were tested at temperatures ranging from -196o to 300°C. Oxygen additions were made to 1/2-in.-diam bars of electron-beam melted material in a Seiverts Apparatus. The oxygenated bars were then homogenization-annealed to obtain uniform cross-section hardnesses and swaged to

Jan 1, 1964

By P. W. Neurath

IN recent years the domain theory of ferromag-netism has been put on a sound experimental and theoretical basis. But its application to one of the most widely used high quality magnetic materials, the cold-rolled grain-oriented 3 pct Si-Fe used in transformer cores, has been rather difficult because of the complexity of the domain structure of the poly crystalline sheet material. This paper presents some experimental data for this material, showing the relation between plastic and elastic stresses, 60-cycle watt losses, and the domain structure as observed visually. Only a very tentative qualitative explanation of the effects will be attempted. Some initial results were reported earlier.'

Jan 1, 1957

By D. C. Ganow, N. J. Grant, I. R. Silver, A. R. Chaudhuri

The structural changes that result when a metal is "cold worked" lead to higher values of yield and tensile strength on subsequent deformation at room temperature. Further it has been shown that the beneficial effects of cold work are, to some extent, maintained even at elevated temperatures. The strength improvements from prior cold work decrease as the temperature is raised and are a function of grain size, amount of cold work, and strain rate (or time of test). If recrystallization occurs during test, the cold-worked material may even show weaker stress-rupture properties than the annealed material. A question that arises is whether there is a significant effect on the subsequent creep behavior if the prior deformation is performed under creep conditions at high temperatures not too different than the test temperature, but at significantly different strain rates and for various amounts of strain. An answer to this question was sought in the work described in the present paper. PROCEDURE Two materials were used in this work, high-purity aluminum and a solid-solution A1 2 pct Mg alloy. The compositions are shown in Table I. The grain size in the two materials was 0.2 to 0.3 mm. The deformation for both the prestraining and for the creep tests was at constant stress. The procedure adopted was to prestrain a specimen to the desired elongation, remove the load, and cool to room temperature rapidly by spraying. the test bar with cold water. The specimen was then placed in a creep machine, held at the test temperature for less than 5 min, and loaded. Less than 15 min was required to bring the specimen to temperature. The creep stress was based on the diameter resulting from the prior strain, and values of elongation at fracture listed in the tables do not include the respective elongations resulting from the prestrain. The choice of the stresses for the prestrain and for the creep tests was made so that the tests could be completed in relatively short times to maximize any effect of prestrain. The specimens had a gage length of 1 in., the pure aluminum specimens having a diameter of 0.150 in. and the alloy specimens a diameter of 0.125 in. For pure aluminum, prestrain was at 400' and 600°F with testing at 500°F; for the alloy, prestraining was at 700°F and testing at 600°F. RESULTS The prestrain conditions for the aluminum and the alloy specimens are shown in Tables I1 and IV. In addition to showing the time required to achieve the desired prestrain, the expected rupture Lives are given which would have resulted had the creep prestrain been continued to fracture. The prestrained and the annealed specimens were then tested in creep to fracture; the temperature and stress for the pure aliminum specimens being 500o F and 1800 psi and for the alloy, 600' F and 3400 psi. The creep curves for the prestrained and the annealed specimens of pure aluminum showed all three stages of creep; hence in addition to the effect of prestraining on the rupture life, it was also possible to determine the effect of prestraining on the minimum creep rate, and on the time and elongation at the end of each of the three creep stages. The results are shown in Fig. 1 and Table 111.

Jan 1, 1960

By J. O. Brittain, E. Lautenschlager

Yield point measurements were made on polycrys-talline specimens of a iron deformed various amounts at 770, 1950, or 273°K, aged, and redeformed at 77: 195°, or 273°K. When the prestrain temperature is lower than that subsequent to aging, the yield point return is suppressed relative to specimens deformed at the same temperature both before and after aging. The degree of suppression is a function of both the magnitude of prestrain at the lower temperature and the difference between the deformation temperatures before and after aging. It is proposed that the suppression is caused by the formation of dislocation barriers during the initial low-temperature deformation. The aging kinetics of polycrystalline a-iron wires deformed at 77o or 303oK were studied at 44 " and 64 "C using internal friction measurements. No change was noted as a result of the difference in prestrain temperature. IN an earlier investigation1 it was observed that the return of the yield point was suppressed when a poly-crystalline specimen of a iron was plastically deformed at 77oK, aged at room temperature, and subsequently tested at room temperature. In order to investigate this observation, a research program was undertaken to measure the effect of prestrain temperature on the strain aging of a iron.' According to Thomas and Leak,3 return of the yield point and internal friction are similar measures of strain aging since both are dependent on solute atoms leaving the solid solution. The decrease in internal friction as a function of aging time is indicative of the removal of solute atoms from the solution, while the return of the yield point as a function of aging time gives the rate of arrival of solute atoms at the dislocations. According to Cottrell and Bilby,4 the solute atoms create an "atmosphere" which locks the dislocations and causes a return of the yield point upon restraining. In this experiment, both methods of measuring strain aging were employed in order to have two independent measurements of the strain aging phenomenon. In a previous study,5 the strain aging kinetics of a similar lot of a iron were measured for specimens which were prestrained and tested at the same temperature over the range of 77" to 273°K. Although some differences were found in the correlation of the two methods employed for measuring strain aging, the kinetics of strain aging were unaffected by the change of prestrain and test temperature. In another study,6 dislocation line tension and the density of the solute atmosphere were found to contribute to the return of the yield point when ingot iron specimens were prestrained at 303°K and tested at a lower temperature, namely 77°K. This paper is concerned with changes in strain aging kinetics produced by pre-straining at 77" to 303°K and testing at either the prestrain temperature or at higher temperatures up to 273°K. EXPERIMENTAL PROCEDURE The polycrystalline a iron specimens used in both the tensile and internal friction tests were 0.033-in. diam ingot iron wires, wet hydrogen treated and re-carburized. A more detailed procedure for processing a 3/16 in. ingot iron rod (nominal wt. pet composition: Fe - 0.013; C - 0.0125; Mn - 0.023; Si -0.005; P - 0.0023; S - 0.11; Cu - 0.004 N) to 0.033 in. diam specimens containing approximately 0.020 wt pet C and no detectable nitrogen with a grain diameter of 0.033 to 0.040 mm is given elsewhere.5 Immediately prior to testing, specimens were solution treated for 15 min at 700o ± 2°C in a static vacuum of less than 50 ?. of Hg and rapidly quenched into an ice-water bath while still enclosed in a 3 mm quartz vial. The internal friction specimens had 8-in. gage lengths and the tensile specimens had 2-in. gage lengths. The wires used as tensile specimens were first run as internal

Jan 1, 1962

By R. A. Anderson, T. E. Tietz, J. E. Dorn

Recent investigations1,2,3,4 have conclusively shown that the strain hardened state of metals depends upon the temperature and strain rate of pre-straining as well as on the total plastic strain. A typical example of the effect of temperature of prestraining on the work hardening of metals is reproduced in Fig 1. When pure aluminum is strained at liquid nitrogen temperature the upper solid stress-strain curve (OFGH) is obtained. But when pure aluminum is prestrained to e2 = 0.153 at atmospheric temperature and the test is then completed at liquid nitrogen temperature, the curve OBCD results. Thus a prestrain E2 = 0.153 at atmospheric temperature gives a flow stress C when continued at liquid nitrogen temperature, whereas a higher flow stress G results when the specimen is strained exclusively at liquid nitrogen temperature to the same strain E2. Consequently the metal strain hardens more rapidly at the lower temperature. Obviously the strain alone is not a measure of the strain hardened state in metals. Inspection of Fig 1 reveals that the flow stress at C is identical with that at F. This fact suggests that a strain E2 = 0.153 at atmospheric temperature induces the same work hardened state as a strain E1 = 0.058 at liquid nitrogen temperature. But this concept of equivalent strains is also in error. If curve CD is shifted to the left so that point C falls on F, point D becomes D'. Inspection of the curves reveals that the rate of increase of stress with strain at C is greater than the rate of increase of stress with strain at F even though the flow stresses are identical. Consequently C and F do not represent identical work hardened states. It therefore becomes important to ascer- tain how the strain hardened states at C and F might differ from each other. In a more recent report1 it was shown that straining at higher rates of strain increases the amount of strain hardening in a manner quite analogous to straining at lower temperatures. These observations suggested that the flow stress is not only a function of the strain but also a function of the strain rate-temperature history of straining, perhaps in accord with the Zener- ?H Hollomon parameter p = Ee /RT (where

Jan 1, 1950

By W. C. Ellis, E. S. Greiner

WHEN metallic materials are deformed plastically, the process may be considered as one in which hardening and recovery occur simultaneously. The net hardening is that produced by deformation in the absence of recovery lessened by recovery during and immediately following deformation. Strain hardening takes place through movements of large groups of atoms acting to a degree as an entity. A complex microstress system is developed. Recovery is a diffusive-type process involving single atoms or, at most, only a few atoms in concerted action. This is accompanied by elastic strain relaxation. Recovery is strongly temperature-dependent. The driving energy for the process resides in thermal fluctuations of the atoms augmented by the energy of the stress field producing the deformation, and by that produced by the deformation. At very low temperatures recovery is essentially absent, or very small. At high temperatures in the hot working range, recovery is so rapid that deformation results in no appreciable net hardening. The interplay of strain-hardening and recovery results in differing end structures depending on the temperature and the strain rate of the process. For example, there is a prominent difference in the spacing of the slip markings and in the detail of X-ray diffraction patterns. High temperatures and slow strain rates favor a wide spacing of slip markings and sharp reflections.',' This suggests that change in rate of the recovery concurrent with deformation modifies to a degree the manner of the deformation. Different slip systems may operate. For very slow rates, the mechanism may, as has been suggested, differ from that of "classical slip." In the experimental work that follows the findings will be interpreted from the point of view developed in this section. Recovery and Electrical Conductivity Electrical conductivity is a sensitive indicator of the state of strain in a material3' * and was used in this investigation. The materials studied in wire form were: OFHC copper, a high purity (99.99 pct) and 2s grade aluminum, and grade A nickel. Wire annealed and initially 0.050 in. in diam was drawn through diamond dies in a simple holder maintained at 25", —75°, or — 195°C. Precautions were taken that for each material all conditions of drawing were the same except the temperature. Electrical resistivity was measured for each condition at 20°C. This was done as soon as practical after drawing to minimize possible room temperature recovery. The data for the four materials are plotted in Fig. 1 in terms of the change in resistivity for drawing at the several temperatures. The effect of temperature of drawing on the increase in resistivity is most pronounced for copper. Drawing at 25°C to 80 pct reduction in area increases the resistivity approximately 2 pct; drawing at —195°C to the same reduction increases the resistivity about 6 pct. The increase in resistivity" & in this metal is due to extra scattering of conduction electrons originating in the lack of orderly arrangement of the atoms induced by the deformation process. It has been suggested

Jan 1, 1953

By D. F. Kaufman, E. D. Levine, L. R. Aronin

The deformation of' impure beryllium crystals by basal glide at room temperature invariably tevminates by basal cleavage after a few percent strain. It is generally accepted that .fracture of this type is caused by the splitting of low) -angle boundaries, or bend planes, by obstacles that restrict the motion of the bed planes in the deforming crystal. The details of such a process have been developed by Stroh, who showed that the high tensile stress norrnal to the basal plane in the region where the bend plane is split results in the propagation of a basal cleavage crack, provided there is no available dejorvrlatzon mode having a shear component normal to the basal plane It has been postulated that puvification of beryllium might lead to increased basal ductility by the vemoval of barviers to bend plane motion and possibly by the activation of nonbasal defor~rlation systems. Large increases in the amount of basal glide that can he sustained prior to fracture have been observed in crystals purified by zone refining. In each case, eventudal fracture was by sharp basal cleavage, suggesting that the split bend plane model still applies to tile fracture of beryllium of rensonably high purity. In the present work, calculations are made to show to what extent basal duetilits can be increased by purification while the split bend plane .fracture process remains applicable. Experimentally observed ductilities are generally somewhat lower than those predicted by calculation because of premature failure due to defects introd~cced during specimen preparation and testing. SEVERAL investigators1-4 have studied the deformation characteristics of beryllium single crystals of commercial purity, and have related the strong anisotropy of plastic deformation in single crystals to the problem of brittleness in polycrystalline beryllium. For most orientations, the principal deformation mode is basal slip, which, at temperatures between 300" and 900°K, begins at a critical resolved shear stress of approximately 1500 g per sq mm and terminates after 3 to 6 pet glide strain by cleavage on the basal plane in the neighborhood of (1120) bend planes that are formed during the deformation. This type of fracture, which is also observed in zinc at low temperatures, has been interpreted by stroh5 to be caused by the splitting of bend planes by obstacles to their motion. In the Stroh model, a (11.20) dislocation wall, or bend plane, moving along the slip direction under the action of the applied stress, encounters obstacles which cause part of the bend plane to be held up, the other part continuing to move. Stress concentrations are built up in the region where the bend plane is split, with a high tensile component normal to the basal plane, resulting in a microcrack at the end of the split wall. Because no deformation mode having a shear component at an angle to the basal plane is available to relieve the stress at the crack tip, the crack can propagate under a sufficiently high applied stress. The Stroh criterion for crack propagation is given by

Jan 1, 1964

By A. S. Nowick, C. Y. Li

It is deMonstrated that quenching from an elevated temperataupe accelerates the grain boundary relaxation in two solid solutions (aAg-Zn and a Cu-Al). This result is consistent with the proposal that, in solid solutions, grain boundary relaxation occurs by a mechanism of' self diffusion. Nevertheless, an alternative possibilitg, that quenching introduces vacancies into the boundary itself, must also be considered. THE phcnomenon of grain boundary relaxation has been well known for many years,1,2 yet the mechanism of this process is very poorly understood. One of the most interesting suggestions which relates to the mechanism of grain boundary relaxation was that of Ke,3 who claimed that the activation energy for grain boundary relaxation and for lattice self diffusion were essentially the same. The implication is therefore that the elementary step in the two processes is the same. This suggestion is particularly startling in view of the fact that activation energy for self diffusion along a grain boundary is very significantly lower than that for volume self-diffusion. Later evidence5-7 showed that there really are two grain boundary peaks, one which appears in high-purity metals, and the other (which develops at a higher temperature than the first) which appears in solid solutions beginning at solute concentrations in the range of 0.1 pct. Data for silver6 show that Kg's hypothesis is surely incorrect for the grain boundary peak in the high-purity metal, since it has an activation energy of only 22 kcal per mole, but that the hypothesis may still be correct for the grain boundary peak in various silver solid solutions, for which activation energies in the range 40 to 50 kcal per mole are observed. If the elementary step in the grain boundary relaxation process were the same as that for self-diffusion, it would be expected that the relaxation process could be hastened by quenching, 2.c. by introducing a non-equilibrium excess of lattice vacancies. Such a quenching effect has already been demonstrated in the case of another anelastic relaxation process, viz., the Zener relaxation effect. The Zener effect, which occurs in essentially all solid solutions, may be attributed to the reorientation of pairs of solute atoms in the presence of an applied shear stress,' and therefore must take place by means of a volume diffusion mechanism. The hastening of this process through quenching9 has been one way of demonstrating that atom movements in the lattice take place through a defect mechanism, presumably single vacancies. In order to see if the grain boundary relaxation is affected by quenching, it is particularly convenient to compare the grain boundary relaxation with the Zener effect, by choosing a specimen for which both relaxation effects appear. Specifically, a fine-grained sample of a solid solution shows in the curve of internal friction vs temperature, first a peak due to the Zener effect, then a second rise (and eventually a peak at substantially higher temperatures) due to the grain boundary relaxation. The same phenomena are also observable in static anelastic measurements, such as creep at very low stress levels. Thus, for the same fine-grained solid solution, the creepstrain, when plotted against log time, falls on a sigmodial curve with a sharp inflection point, due to the Zener effect, which is followed by a second rise and inflection resulting from the grain boundary relaxation. To look for a quenching effect, static measurements are preferable to the dynamic internal friction measurements, due to the fact that quenching effects tend to anneal out too rapidly at the temperatures at which the internal friction is measured.9 RESULTS AND DISCUSSION Creep experiments in torsion were carried out in an apparatus similar to that described by Ke1, whereby a wire is held under constant torque and its angular displacement is observed as a function of time. The alloy Ag-30 at. pct Znwas selected because of the large Zener relaxation that it displays. The two samples used were a "coarse grained" wire with a mean grain size about twice the diameter of the wire (diam = 0.032 in.), and a "fine-grained" wire which had several grains across the diameter. In Fig. 1 a comparison is made of the creep curves at 160°C of these two samples after they had been cooled slowly from 400°C. Curve A, which represents the coarsegrained sample, shows a unique relaxation process due to the Zener relaxation, with a relaxation time, T , in the vicinity of 100 sec. Curve B, which represents the behavior of the fine-grained sample, on the other hand, shows first the same relaxation process as that in A, followed by a turning up of the curve which corresponds to the onset of a second overlap-

Jan 1, 1962

By T. E. Leontis

The specific effect of various rare-earth metals on the room- and elevated-temperature properties of magnesium has been evaluated. Alloys containing didymium exhibit the highest tensile and compressive strengths at room and elevated temperatures. All the rare-earth metals increase the creep resistance of extruded magnesium at temperatures in the range of 400° to 600°F, but the degree of enhancement depends on the temperature and on the concentration of the added metal. THE effects of rare-earth metals on the properties of sand-cast magnesium were discussed in some detail in earlier paper by the author.' The present paper deals with the effect of the same alloying elements on the properties of extruded magnesium. This investigation also had as its aim the development of a wrought alloy having a better combination of room-temperature strength and ductility and elevated-temperature strength and creep resistance than is found in magnesium-Mischmetal-manganese alloys, which have been reported earlier.2-5 The only known attempt to study wrought magnesium alloys containing pure cerium instead of Mischmetal was made by Mellor and Ridley.6 They found that in the form of rolled bars there is a definite, optimum cerium content for creep resistance at 200 °C and that the creep resistance of these alloys at 200 °C is significantly Improved by heat treatment at 550" to 580"C. In the present investigation the compositional variation in mechanical properties of the following alloy systems is presented: I—magnesium-Misch-metal. 2—magnesium-cerium-free Mischmetal. 3— magnesium-didymium. 4—magnesium-cerium. 5— magnesium-lanthanum. Alloys containing predominately praseodymium are not included in this series because of the lack of this material. Experimental Procedures The alloying ingredients used in preparing the alloys described herein are the same as those reported in the earlier paper.' Cerium-free Mischmetal is the rare-earth mixture remaining when the cerium is removed from Mischmetal, which contains all the rare-earth metals as they occur naturally in mon-azite sand, the ore from which Mischmetal is produced. Removal of both cerium and lanthanum from Mischmetal leaves what is commonly called "didym-ium," consisting predominantly of neodymium and praseodymium. Although the composition of the particular batch of each metal used may differ somewhat from the analysis presented previously, these differences are not great enough to warrant repeat- ing the specific composition of each material. The electrolytic magnesium used as the starting material in these alloys has the same typical analysis as that given in the earlier paper.' The alloys were prepared in small laboratory melts applying all the necessary precautions for alloying rare-earth metals with magnesium described by Marande.' Most melts were large enough to cast one 3 in. diam billet 10 in. long. In a few cases, particularly the didymium-containing alloys, the lack of sufficient amounts of the rare-earth metal limited the size of the billet to 6 to 8 in. All billets were scalped to a diameter of 2 15/16 in. and faced to a length of 9 ¼ in. as limited by the size of the extrusion container. The alloys were extruded into ½ in. diam rod on a 500-ton direct-extrusion press using a 3 in. container. The details of the extrusion step are: billet preheat, 925°F (2 hr); container temperature, 900°F; die temperature, 900°F; extrusion speed, 10 ft per min; reduction ratio, 36:1; and percent reduction, 97.3. The lower melting point of alloys containing didymium' necessitated reduction of the extrusion speed to 5 ft per min in order to prevent hot shorting during extrusion. Adequate lengths were cropped from both ends of each extruded rod to assure that all the material used for tests was extruded under uniform conditions. Tensile and compressive properties at room temperature are reported in the several conditions of heat treatment. The ASTM designations are used to distinguish these conditions as follows: T5—Direct age at 400°F (16 hr) T4—Heat treat at 950°F (4 hr) for alloys containing didymium T4—Heat treat at 1050°F (4 hr) for all other alloys T6—T4 + age at 400 °F (16 hr) The lower heat-treating temperature for alloys containing didymium is necessitated by the lower melting point of these alloys. All heat treatments were conducted in electrically heated, circulating-air furnaces. A protective atmosphere containing 0.5 to 1.0 pct sulphur dioxide was used for the high temperature heat treatments. Tension and creep specimens 6 Yz in. long and compression specimens 1½ in. long were cut from the extruded rod. A reduced section of ? in. diam was machined on the tension specimens, whereas on the creep specimens a reduced section of 0.450 in. diam

Jan 1, 1952

By Pol Duwez

The effect of the rate of cooling on titanium, zirconium, and thallium has been measured. For titanium-molybdenum alloys, it has been shown that for molybdenum concentration up to 8 pct the rate of cooling has no effect on the transformation temperature, but this temperature decreases progressively with increasing molybdenum content. HIGH strength to weight ratio and remarkable corrosion resistance have often been advanced as the main reasons for the present widespread interest in titanium. For the physical metallurgist, the existence of an allotropic transformation in titanium is another important factor. As in the case of iron, an allotropic transformation may be the fundamental property upon which the response of Ti-base alloys to heat treatment will depend. It is therefore important to study the mechanism of the allotropic transformation in pure titanium and the effect of alloying elements on this transformation. The existence of an allotropic transformation in titanium was reported in 1931 by Schulze.' Later, De Boer et al.' determined the transformation temperature from a discontinuity in the electrical resistivity at 882"42O°C. According to recent work," the transformation temperature is 882.5"&1°C. The crystal structure of the room temperature a phase is hexagonal close-packed and the high temperature fi phase is body-centered cubic.' It is well known that the high temperature /3 phase of pure titanium cannot be retained by quenching to room temperature. Several investigators'-' have shown that in alloys of titanium with metals which are soluble in the @ phase (for example, nickel, molybdenum, chromium, or manganese), the /3 structure can be retained, providing the concentration of the alloying element is greater than a certain critical value. Below this critical value, the alloys transform during quenching, at least partially, into a supersaturated solid solution having the a. structure. This behavior is very similar to that found in some iron binary alloys (Fe-Ni and Fe-Mh, for example) and is an indication that the transformation might occur by means of a shear mechanism analogous to that observed in the austenite-martensite reaction. The present investigation is mostly concerned with the effect of the rate of cooling on the /3 to a transformation. In the first portion of this paper, the results obtained on pure titanium are described. Two other pure metals, zirconium and thallium, were also investigated, because they both have an allotropic transformation like titanium, from an hexagonal close-packed to a body-centered cubic structure. For purposes of comparison, the effect of rate of cooling of the y to a transformation of iron was included in the experimental program. The second part of this paper deals with Ti-Mo alloys. The equilibrium phase boundaries involving the solid state reactions on the Ti-rich side of the system were determined and a study was made of the effect of the rate of cooling on the transformation of the high temperature /3 solid solution. Experimental Procedure Since the main object of the present investigation was the determination of the effect of the rate of cooling on a transformation temperature, the best technique available was that used by Greninger" in his study of the martensite arrest in carbon steels. This method consists of heating a very small sample of metal to which fine thermocouple wires are .attached, cooling the sample rapidly by means of a blast of helium, and recording the temperature vs. time curve on an oscillograph. The apparatus used in the present experiments was very similar to that described by Greninger, except that the heating coil was made of molybdenum wire (0.040 in. in diam) and the assembly was placed in a bell jar under vacuum of 10" mm Hg or less. The specimen con-

Jan 1, 1952

By J. L. Lytton, T. E. Tietz

The recovery of flour stress of recrylstallized are-cast molyhdenum after 10 pet prestrain at 150°C was studied for recovery temperatures of 725o 801o and 901oC. The yield phenomenon observed after recovery was such that the yield drop diminished and disappeared as recovery proceeded. A fractional flow-stress recovery parameter fr, was developed and it was shown that, independent of recovery ternperatzwe, equal f, values of about 0.16 produced superposition of stress-strain curves except for the initial yield phenomenon. The activation energy for low degrees oj recovery was found to he 32,600 cal per mole, in close agreement with a reported valzie for difjzdsion of carbon in molybdenum. For values of fr greater than about 0.15 where recovery was thought to predominate over strain aging, the activation energy varied from 43,600 to 82,500 cal per mole and increased with increasing recovery and recovery temperature. A 10 pet pre-strain shifted the ductile-brittle transition temperature, as indicated by tensile elongation, from 10°C. to about -22"C. A 100-hr recovery anneal at 801oC was shown to shift the transition temperature to about —5oC, the major shift occurring during the first hour of recovery. ThE recovery of cold-worked metals is accompanied by changes in the arrangement of the dislocations generated during cold work. In recent years, the use of transmission electron microscopy has allowed direct observation of some of the dislocation configurations formed, such as "tangles", networks, cells, subboundaries, and loops. These observations have recently been reviewed by Keh and Weissmann.' Accordingly, some understanding has been gained concerning the nature of the dislocation rearrangements involved. The relationship between recovery and the decrease of mechanical strength, however, has only recently been explored. Previous efforts of the authors were directed toward investigating the decrease of tensile flow stress of aluminum and Al-1 pet Mg during recovery2 and the effects of concurrent elastic and plastic strain on the flow-stress recovery of aluminum.3 In addition, an investigation of the effect of four different solute additions on the tensile flow-stress recovery of aluminum has been made.4 Many important metals, however, have the bee crystal structure, e.g., iron, molybdenum, tungsten, vanadium, columbium, tantalum, and chromium. These metals might be expected to behave differently during recovery from those with other crystal structures for two reasons. First, the previous and present investigations of aluminum and its alloys have shown that tensile flow-stress recovery is strongly affected by foreign atoms in the lattice. In the bee metals, interstitial impurities are usually present and might be expected to have various effects upon both flow behavior and recovery. For example, heterogeneous yielding might occur during prestraining. The diffusion of these interstitials can also relock dislocations during recovery so that a yield point might be obtained upon restraining (strain aging). Second, some of the bee metals (e.g., iron, molybdenum, and tungsten) undergo the familiar structure-sensitive ductility transition and exhibit brittle fracture at suitably low temperatures. It is of considerable interest to determine the effects of recovery on the transition temperature of such metals. The purpose of the present investigation was to extend our knowledge of flow-stress recovery to the bee metals and to study the effects of recovery on the ductile-brittle transition temperature. Unalloyed recrystallized are-cast molybdenum was chosen as a test material, since it exhibits a well-defined ductility transition near room temperature. As in the previous studies, the degree of recovery was measured in terms of the decrease of tensile flow stress. Prestraining and restraining were carried out at 150°C to avoid the possibility of brittle fracture. EXPERIMENTAL PROCEDURE The are-cast molybdenum sheet used in this investigation was obtained from the Climax Molybdenum Co. of Michigan. It was 0.060 in. thick by 10

Jan 1, 1964

By W. R. Hibbard Jr., T. Michalak

THAT the amount of deformation and annealing time influences the recrystallization temperature of cold-rolled copper has been well established. Evidence that the recrystallization temperature can be affected by the deformation texture has been reported by Brick and Williamson,% ho found that copper straight-cold-rolled to 99 pct reduction to produce one deformation texture and copper cross-cold-rolled to 99 pct reduction to produce a second and different deformation texture correspondingly recrystallized at different temperatures to different textures. The purpose of the present work was to study more thoroughly the effect of the deformation texture on the recrystallization of cold-rolled copper. Experimental Procedure The copper used in this investigation was commercial OFHC copper (nominally 99.985 pct Cu) in the form of 0.500-in. plate. Qualitative spectro-graphic analysis showed only a slight trace of iron and a trace of silver. No analysis was performed to determine the exact content of the iron and silver,

Jan 1, 1958

By K. P. Gupta, P. A. Beck, N. S. Rajan

By determining the a phase boundaries in the following ternary systems: V-Fe-Si (at 1175oC), V-Co-Si (at 1175°C), V-Ni-Si (at 1175oC), Cr-Mn-Si (at 1000°C), Cr-Co-Si (at 1175°C), Cr-Ni-Si (at 1175°C), V-Fe-A1 (at 1175°C) and Cr-Co-A1 (at 1175°C), it was found that Si exerts a stabilizing effect on these a phases, while A1 tends to destabilize them. Si atoms in solid solution occupy sites D in the a structure, The co/ao ratio increases with increasing Si-, Mn- or Fe-content. The volume of the unit cell decreases with increasing Si-content. THE stabilization of certain metal silicides (the Nowotny phases) by the addition of relatively small

Jan 1, 1961

By R. M. Treco

The effect of small additions of oxygen on the hardness, density, and lattice parameters of high purity zirconium has been investigated. Precision parameter values and density of oxygen-free zirconium are given as: a,, - 3.2258 kX units, C = 5.1373 kX units, O23 = 6.507 g per cc. THE effect of oxygen on the hexagonal-phase lattice constants of pure zirconium is of interest for several reasons. The extensive hardening effect of oxygen noted by previous investigators' must be due in part to the lattice distortion accompanying its introduction and possibly to the preferred position of the oxygen atoms. De Boer and Fast' have shown that oxygen is taken into solid solution in large amounts, appearing to occupy an interstitial position. These authors also found that expansion of the lattice was not uniform since the a axis attained a constant value after the addition of 10 atomic pct while the c axis continued to expand. It was thought in the present work that this expansion of the zirconium lattice with increasing amounts of oxygen

Jan 1, 1954

By G. W. P. Rengstorff, L. E. Olds

PREVIOUS research has shown that cast molyb-denum has good ductility at room temperature if the metal is sufficiently pure. In practice, however, it is very difficult to reduce the impurity content of molybdenum to a few parts per million—the maximum content of impurities allowable to obtain reasonable ductility in coarse-grained molybdenum. Also, subsequent fabrication may reintroduce enough impurity to damage ductility greatly, unless extreme precautions are taken to protect the metal during working. The major impurities which embrittle molybdenum are oxygen, nitrogen and, to a lesser degree, carbon. It is reasonable to assume that the harmful effects of such impurities might be neutralized by small amounts of alloying additions. The desired alloying elements would be those which might fonn stable metal oxides or nitrides that would not be harmful to ductility, or thosewhich might increase the tolerance of molybdenum for oxygen and nitro-

Jan 1, 1958

By R. S. French, W. R. Hibbard

FOR tensile deformation, if the stress value is defined by the ratio of the load to the actual area, and the strain value by the natural logarithm of the ratio of the immediate length to the original gauge length of the sample, the resulting data when plotted with logarithmic coordinates result in a linear relation extending from the initial plastic yielding through the maximum load and in some cases, such as for copper and brass, to fracture'.'. The normal form of the curve, therefore, is a parabola, satisfying the following equation: S = Kem [1] where S and e represent true stress and strain, K is a constant, and m is a coefficient evaluating the slope of the curve and designated therefore as the strain hardening coefficient. Hollomon² has reported that this coefficient is a function of the yield strength as effected by grain size in alpha brass, and the carbon content and heat treatment of steel. In the case of steel, the value of the proportionality constant is a function of the carbon content. It was further shown in that paper2 and also by Low and Prater -hat, if the power relation between stress and strain remains valid, the strain hardening coefficient m, is equal to the strain at the maximum or necking load. Thus, an added significant feature is that this coefficient may serve as an index of the capacity for deformation prior to localized necking and subsequent fracture, e.g. drawability. The constant K may be defined as the strength of the material at unit strain. Together the K constant and the m coefficient describe an alloy's physical properties as far as strength and ductility are concerned for a particular yield strength and, in the case of steel, a particular carbon content. The work of Lacy and Gensamer4 gives data on alloy ferrites from which very close estimates of the strength of ternary and higher iron alloys have been made. It was the purpose of this investigation to develop similar data for commercial copper base alpha solid solution alloys. Preparation of Specimens Commercial binary alloys of copper with aluminum, beryllium, cadmium, nickel, silicon, tin and zinc were investigated. In addition, laboratory castings were made of a 1 pct silicon alloy and a 2 pct aluminum alloy to complete these particular series. Two types of copper were used, oxygen free OFHC and tough pitch FC. The analyses of these alloys are shown in table I. Standard ASTM sheet tensile specimens were used to determine the usual physical properties of each alloy and to obtain stress data at strains from 0.0005 to 0.01. Small (1/4 in. x 3 in. x tk.) samples

Jan 1, 1951

By R. S. French, W. R. Hibbard

M. Balicki—As one who some years ago spent much time searching for an alloy with high thermoelectric power that would be suitable for heat energy-electric energy converter based on the principle of a thermoelectric pile, I would like to make a few comments touching upon that aspect of this excellent paper. The specifications which one of the authors has formulated so aptly do not appear to me as complete, and I would like to add to them the following two demands: (1) Melting point not less than 500°C and (2) elongation on 2 in. at least 5 pct. Condition 1 would insure good thermodynamic efficiency of the pile by permitting a reasonably high temperature of the hot junction and at the same time making it suitable for such application as salvage of vast amounts of energy which is lost in the form of sensible heat of waste gas leaving industrial and other furnaces. Condition 2 is also a very important one; particularly, because of the fact that all elements and alloys which exhibit attractive thermoelectric properties seem to be as a rule very brittle. The design, erection, and maintenance of a pile incorporating a brittle material in one of the most crucial parts of the converter would be a very difficult and costly affair indeed. To illustrate this point I may mention great difficulties I encountered when trying to make thermocouples of silicon. Casting of 1/4-in. rods in iron or graphite mould yielded only broken pieces which had to be welded into a bar. Such a bar had to be handled very carefully during the determinations. Raising the molten silicon by vacuum into a silica tube and solidifying it there solved the problem of stability as well as that of electrical insulation of a bar. On tests this bar (98.5 pct Si) showed dE/dT = — 275.5 microvolts per degree C vs. copper. Thermocouples made of this grade of silicon and pure nickel developed 0.39 v when temperature of the hot junction was approximately 1000°C. The possibility Dr. Gonser has mentioned of trying to impart to metals good thermoelectric properties by alloying them with silicon, has been considered. The preliminary survey which I have made was, however, disappointing. Perhaps, it will be advisable to record the results obtained (table VI), as this might save repetition of search in fields already covered.

Jan 1, 1951

By J. W. Rutter, K. T. Aust

THE object of the experiments to be described in this report was to determine, first, which grains, out of a large number introduced into a sample in which their growth could proceed, were able to grow most successfully; and, second, the factors which control their growth selection. In an earlier study of grain boundary migration in high-purity lead,' it was found that, under some conditions, the most successful grain in an experiment of this type bears a special orientation relationship to the grain into which it is growing. The present work represents an extension of the previous study, directed at the determination of the orientation relationships which appear under a wider variety of conditions. Experiments of this general type have been done using commercial aluminum2 with somewhat conflicting results. In the present experiments, in contrast to the above,' the sample composition was a principal controlled variable, resulting in a considerable clarification of the phenomena observed. EXPERIMENTAL TECHNIQUE The experimental technique used in this investigation was essentially that employed previously in studies of grain boundary migration kinetics.1'3 The material used was zone-refined lead with various small amounts of tin or silver added to study the effect of varying the sample composition. The specimens were in the form of single crystals, about 1/4 in. 1/4 in cross section by 3 to 4 in. in length, grown from the melt in a horizontal graphite boat. A crystal grown in this way generally contained a lineage or "striation" substructure of the type shown in Fig. 1 of Ref. 1. This substructure consists of an array of low-angle boundaries which partition the crystal into regions misoriented from each other by a few degrees. The substructure constitutes a source of driving energy, estimated to be about 4000 ergs per cc, for the migration of a large-angle grain boundary into the striated crystal. New grains were introduced by plastic deformation in compression of a localized reglon at one end of the sample. Re-crystallization occurs at room temperature in the deformed region, introducing a large number of new, striation-free grains into the specimen. These grains are able to grow into the melt-grown crystal on annealing at a suitable temperature. The stria-tions are removed by passage of the grain boundary, as the substructure energy is utilized to produce the boundary migration. Usually, only one or two of the recrystallized grains persist after growth has occurred for about 1 cm out of the deformed region. Laue back-reflection X-ray photographs were obtained to determine the orientation relationship between the melt-grown crystal and the recrystallized grain or grains which grew most successfully in each specimen. EXPERIMENTAL OBSERVATIONS Fig. 1 shows the results obtained for a series of specimens to which had been added tin in the range from 0 to 5 ppm by weight. In this figure is plotted, in the standard stereographic triangle, the single axis about which the most successful recrystallized grain or grains are related to the starting, melt-grown crystal by the smallest rotation. The range of angular rotations observed about such axes is indicated beside each stereographic triangle. The results shown in the stereographic triangle on the left, Fig. l(a), were obtained by localized deformation at one end of each specimen at room temperature, followed by annealing in a furnace which had been preheated to 300°C. The furnace atmosphere was argon. It will be seen that the orientation relationships observed between the melt-grown and recrystallized grains are quite random. On the right, Fig. l(b), are shown results for samples in which the de-

Jan 1, 1961

By J. Philibert, A. G. Guy

Diffusion in the presence of deformation was studied by the method of vacuum dezincification of copper-rich and silver-rich solid solutions containing 7 to 30 pct Zn. The specimens were designed to permit the study of diffusion in separate portions of a given specimen characterized by strain rates ranging from essentially zero to approximately 10 sec-. No effect of deformation on diffusion was observed. BEGINNING with the work of Buffington and Cohen: interest in the question of the effect of stress or strain on diffusion has largely been concentrated on the enhancement of diffusion in specimens subjected to Continuous plastic deformation. The present research is a contribution to this limited area. However, as a preliminary to focusing attention on this special topic, it will be desirable to make a broad survey of the larger question, especially since there has been considerable foreign work in areas outside those of current interest in the United States. Since most of the topics referred to in the following section are both complex and imperfectly understood at present, it has been expedient in most instances to offer only a guide to the general nature of the work rather than a critical evaluation. PREVIOUS WORK The effect of elastic stress on diffusion has received considerable attention, especially with regard to the thermodynamic driving force for diffusion. The thermodynamic treatments have been based on the work of Gibb, Voigt, Planck, and Leontovich.' Konobeevskii and Selisski6 made a first attempt at treating the problem in 1933, and Gorskii7 a few years later gave a solution applicable to single crystals as well as to polycrystalline specimens. In 1943 Konobeevski8 published treatments that have been the basis of much Russian work up to the present. For example, Aleksandrov and Lyubov used his work in explaining the velocity of lateral growth of pearlite. Early work in the United States was that of Mooradian and Norton, which showed that lattice distortion tends to be relieved before it can significantly affect the diffusion process. Druyvesteyn and Berghoutl1 observed a slight effect of elastic strain on self-diffusion in copper, while de Kazinczy12 found that both elastic and plastic deformation increased the rate of diffusion of hydrogen in steel. On the other hand, Grimes58 observed no effect of either elastic or plastic straining on the diffusion of hydrogen in nickel. High-frequency alternating stresses have been reported by various investigator s13-l5 to increase the rate of diffusion. A special form of elastic stressing is the imposition of hydrostatic pressure, a condition that is amenable to Conventional thermodvnamic analysis. Most of the experimental results in this area are consistent in showing a slight decrease in diffusion rates at high pressures.16-l8 Although Geguzinl reported a pronounced effect of relatively small pressures, Barnes and Mazey20 failed to Corroborate this finding, while Guy and Spinelli21 advanced an explanation of the phenomenon observed by Geguzin. It has been recognized that the thermodynamic treatment of diffusion phenomena in an arbitrarily stressed body is complicated by the fact that the desired state of quasi-equilibrium of the shear stresses cannot be maintained during a general diffusion process. However, attempts have been made by Meix-ner22-24 and Fasto to treat certain restricted cases, such as relaxation. FastovZ7 has also incorporated the general stress tensor into the thermodynamics of irreversible processes. The lattice strain that accompanies the formation of a solid solution has been the subject of much study,28-s0 and indirectly it has entered into many recent theories of diffusion. However, some Russian investigators31'32 have taken other views of this matter and have predicted large effects on diffusion rates because of concentration stresses.o In completing this brief resume of previous work involving elastic strains and before proceeding to a consideration of the effect of continuous plastic deformation, it should be pointed out that deformation of various additional types may also influence diffusion. The effect of cold-working on subsequent diffusion has been studied directly by AndreevaS and by Schumann and Erdmann-Jesnitzer, while indirect evidence has been obtained by Miller and Guarnieri and by Vitman.38 Thermal stresses may also influence diffusion, contributions to this subject having been made by Fastovs7 and by Aleksandrov and Lyubv. The work of Johnson and Martin,o Dienes and Damask,3Band DamaskS considered the question of radiation-enhanced diffusion. In considering previous work on the subject of plastic deformation and diffusion, attention will be directed to those studies concerned primarily with diffusion rather than with its relation to Creep, e.g., the work of Dorn, or to the acceleration of diffusion -controlled reactions. Observations of the effect of

Jan 1, 1962

By W. J. Rogers, L. J. Dwiggins, R. O. Williams

THERE has been comparatively little work on the importance of strain rate and temperature as variables in the formation of deformation textures. For this reason the present work was started, the choice of compression being in part that of convenience and in part because of the absence of quantitative data in this area. These do not turn out to be important variables within the range studied which permits the results to be condensed into this note. Samples 1/4 in. in diam and 1/2 in. long were machined from 99.9 pct pure commercial aluminum and recrystallized to a fine grain size. A set of five samples were deformed between a spring-driven weight and an anvil resulting in roughly 20 pct strain each time. The strain rate varied because of decle-ration and shortening of the sample but would average about 10&apos; per min. Deformation at temperatures over the range of -76" to 150°C were obtained by heating or cooling the samples. Complete lubrication could be obtained by oil since the short time of contact did not permit its escape. The samples were compressed to a total true strain of 1.4 to 1.6. A larger sample was prepared similarly with spiral grooves in the ends to hold paraffin which provided essentially complete lubrication. This sam ple was compressed slowly at room temperature at a rate of about 2 per min to a total strain of 1.0. Cylindrical samples were carefully machined from these discs with a radial direction as an axis. They came from the center half of the samples and were roughly 1/16 in. in diam. The samples were etched down 15 pct to remove any surface effects. Diffraction data were then obtained for six different kinds of planes by the use of the Norton technique as applied to a fiber texture. Direct comparison between the raw data failed to reveal any significant difference between any of the samples and consequently the data from only one sample was completely reduced. The particular sample had been deformed at O°C The background was subtracted from the intensity data which were averaged over the four quadrants and then normalized to random. These data were then used to obtain fiber-axis distribution charts as previously described.2 For this sample the (422) plane was also run to assist in this inversion. The final result, Fig. 1, provided a comparable fit to that previously obtained from fiber data. About 85 pct of the material forms an elliptical texture around the <110> direction. The radius (at half height) is 5.5 deg along the (111) boundary and 8 deg along the (100) boundary. The remaining 15 pct forms a ridge running from this texture to near the <311> direction. The regions around the (100) and (111) planes are devoid of material. The earlier qualitative results of ~arrett~ are in complete agreement with the present results. The possibility has been dis-cused that the material around the <311> results from friction between the sample and compression plates.4 The present results are considered proof that such is not the case because of the uniformity of sample deformation and the requirement of axial symmetry before fiber-axis distribution charts can be accurately obtained. Recently results have been obtained to show that strain rate and temperature are important variables in the extrusion of aluminum.5 Perhaps the most important observation was that the partial recrystal-lization occurred even at room temperature. Strain rate was considered to be a factor only in that it produced a temperature change. There are many differences between the two experiments, the most important possibly being that their material was roughly ten times the purity of the present material. The present experiment, however, may not be as definitive as desired in this respect since it has been shown that compressed aluminum recrystallizes without a texture change6 although supplementary

Jan 1, 1961