Search Documents

By Leonard G. Austin

INTRODUCTION Run-of-mine (ROM) coal generally falls into two major groups: that from underground mining (continuous mining machines) and that from strip mining. Continuous miners produce a finer product and strip mining a coarser product that is crushed to produce the desired size. Further size reduction depends on the proposed use or uses for the coal. For example, for pulverized coal power plants as a rough general rule, the coal is ground or pulverized to 80% less than 200 mesh (0.075 mm) before it is blown into the boiler furnace as a coal-air suspension. For solvent-refined coal processes, the desired size is about <30 mesh (< 0.60 mm); in fluidized bed uses, the coal is typically < 8, in. (< 1.6 mm); for Lurgi pressure gasifiers, the desired size is 1 to 2% in. (25 to 63 mm). Coal preparation plants typically work with a coarse size fraction of 6X 1/14 in. (150X32 mm). The past decades has shown a steady increase in the tonnage of coal cleaned, 1 but it seems probable that the next decades will produce much wider applica- tion of deep coal cleaning before use and that the stages of crushing and pulverization from ROM coal to end use will be integrated with coal cleaning processes. Since different cleaning processes work better with different ranges of coal size and the degree of cleaning possible is intimately connected with the size of coal, a systems design engineer will need as much information as possible concerning the size distributions produced by different types of machines and how these can be modified by different ways of operating the machines. In general, the following questions will be of concern: 1.What type of crusher or grinder is best, or most satisfactory, for reducing a given feed size and type of coal to a desired product size? Frequently, the desired product is smaller than some nominal size, but with as few fines as possible, or the fraction in some size range has to be as high as possible. 2. How big does the machine have to be for a given throughput rate? 3. How much electrical energy (or its equivalent) is required per ton of product? 4. How does the size distribution vary with change in throughput rate, and is a control scheme necessary or desirable? 5. Can the size distribution be readily varied if desired? 6. What is the optimum way to operate a machine in a given system? This section will emphasize certain general principles which guide us in answering these questions. PARTICLE SIZING Since particle size and size distribution are the raw information with which we work, it is worthwhile to review the terminology used. In this regard, see

Jan 1, 1991

By G. S. Dobby

The Cu-Au flotation cleaning circuit at Freeport Indonesia consists of three stages: two flotation column stages, in series, followed by one stage of mechanical cells. Concentrate from both column stages is combined as final concentrate. The mechanical cell stage has two parallel rows of seven Wemco 500&apos;s. The Wemco concentrate is recycled to feed of the second column stage and Wemco tails report to final tailings. This paper examines cleaner circuit performance, focusing on size-by-size performance of the individual stages and the individual mineral groups -copper sulfides, gold and in sol minerals. The recovery mechanisms of insol minerals are examined.

Jan 1, 1995

By T. L. Myron

In recent years increasing attention has been given to improving both the chemical and physical properties of sinter. The first step toward this goal was the production of a self-fluxing-sinter. More recently, blast-furnace operators have found that significant improvements in blast-furnace performance can be achieved by improving and controlling the physical size of the sinter. The results of full-scale blast-furnace tests have shown that blast-furnace production can be improved by using a closely sized agglomerate. The improvements obtained by the use of pellets, a closely sized agglomerate, are well known. In contrast, blast furnaces charged with sinter having a wide size spectrum have generally not yielded results as satisfactory as those from furnaces 1) * charged with pellets. Beginning in 1958, Appleby-Frodingham charged plus 3/8-inch sinter to their blast furnaces. Further tests by other companies in Canada, 2) the United States, 3) and Australia showed that blast-furnace production could be improved by about one percent when the plus 3/8-inch material in the burden was increased by one percent. Because of the promising results obtained with screened sinter, an extensive test program was initiated to determine an effective means of producing sized sinter in U. S. Steel&apos;s sinter plants. This paper describes the work done by the Applied Research Laboratory in this program.

Jan 1, 1965

By William Firmstone

ON the 19th December, 1833, a patent was granted to F. W. Geisenheimer, for smelting iron ore with anthracite. In his claim he says: "Sixthly, though I cannot, and do not, claim am exclusive right of the use of heated air, for any kind of fuel, nevertheless I believe to have a right to claim the use of heated air, applied upon, and in connection with, the said principle and manner discovered by me, to smelt iron ore in blast-furnaces with anthracite coal, by applying a blast of air in such quantity, velocity, and density, or under such pressure, as the compactness, or density, and the continuity of the anthracite requires, as above amply and fully described and illustrated." Dr. Geisenheimer made experiments in smelting iron ore with anthracite at the Valley Furnace, near Pottsville, but he failed to carry out to good practical results the principles enunciated in his patent. In the Journal of the Franklin Institute for February, 1838, a communication was published that was made by Mr. George Crane, of the Yniscedwyn Iron Works, South Wales, to the British Association, in September, 1837. On the smelting of iron with anthracite coal, Mr. Crane states therein, that he began the use of an¬thracite with hot-blast on the 7th February, 1837, in a cupola blast-furnace, 41 feet high, and 10&apos; feet across the boshes ; product, 34 to 36 tons a week. Mr. Crane goes on to say, "It may not be uninteresting to be informed in what matter the idea first occurred to me of applying a heated blast to anthracite coal. One evening, after I had placed a piece of it upon my parlor fire (which had before been made up with bituminous coal), and had allowed it to arrive at a red heat, upon applying as fierce a blast to this piece of coal as I could raise from a pair of bellows, I noticed a black spot or mark

Jan 1, 1875

And it takes more than good organisation. You may read or heard this poignant reflection: We tried hard, but it seemed that every time we were beginning to form up in teams we would be reorganised. I was to learn later in life that we tend to meet any new situation by re-organising, and a wonderful method this is for creating the illusion of progress while producing confusion, inefficiency, and demoralisation This was written by the Roman Gaius Petronius in AD65. How much have things changed in nearly 2,000 years? What then does it take besides the fundamentals and good organisation to build a successful career in a successful organisation? I&apos;m prepared to venture a list of what I&apos;ll&apos;call Tips for Young Professionals. If you&apos;ve got what it takes, and apply these, I think that you&apos;ll gain a great deal of satisfaction from your career, even if you don&apos;t reach the distant target each of you should have in mind now. So settle back in an advice-receiving mode, and please forgive me if I come across as a master of the bleedin&apos; obvious, as Basil once accused his wife Sybil of being in the unforgettable Fawlty Towers.

Jan 1, 1990

By J. E. Gill, A. R. Byers

"The property of Sladen Malartic Mines, Limited, is in the northern half of Fourniere township, Abitibi county, Quebec. The group is large, but the part so far found to be of economic interest is a strip 3,200 feet long between the Canadian Malartic property to the west and the East Malartic and National Malartic properties to the east ( Fig. 1).The original claims were staked in 1923 and 1924 by St. B. Sladen and H. S. Kennedy because gold was known to occur on claims nearby. In 1928, detailed mapping of the Malartic Gold Mines property (now Canadian Malartic) showed the presence of an east-west gold-bearing zone traceable almost to the Sladen boundary. During the winter of 1929, a hand-driven drill was used to secure short sections of core through casing pipe sunk to bed-rock. This proved the existence of the main Sladen ore zone, but it was not until the price of gold was increased, in 1934, that serious work was attempted.Underground work was started in 1935 and milling in January, 1938. To the end of 1945, 168,882 oz. of gold were recovered from 1,641,974 tons of ore, an average of 0.103 oz. a ton.GEOLOGYThe bed-rock underlying' the Sladen Malartic property consists mainly of Precambrian greywacke and volcanics that appear to form a conformable series with a general northwest strike and vertical to steep northerly dip. Except where disturbed locally by drag folds or faults, tops face north. Intrusive rocks that range in composition from diorite to granite cut the sediments and volcanics. The basic types, generally quartz diorite and diorite, form dykes or sills in the volcanic rocks. The more acidic types, mainly quartz syenite and related porphyries, intrude the volcanics and the sediments in the form of dykes, sills, and larger, stock-like bodies.The orebodies are parts of slightly shattered or brecciated zones, mainly in greywacke, but partly in syenite, diorite, and volcanics, that have been more or less replaced by fine-grained quartz, pyrite, and minor amounts of sphalerite, galena, sylvanite, petzite, and gold."

Jan 1, 1954

By C. H. Jr. Herty

ALMOST every metallurgist who has given the Howe Memorial Lecture has had a personal contact with the distinguished gentleman to whose honor this hour is devoted. Unfortunately for me, such personal contacts were not possible. However, in the preparation of a thesis on the open-hearth process, one of my earliest tasks was to make a survey of the literature, and it was from Professor Howe&apos;s Metallurgy of Iron and Steel that I drew a number of references to previous work which formed the foundation for my reading. In his volume there is such a complete exposition of the then current thought on the subject of slags and on their role in the elimination of phosphorus from steel that I feel no hesitation in discussing in this Howe Lecture the subject of "Slag Control." In the present era of close specification, the drive for uniformity of product, and the close inspection of the product and of the cost sheet, the utmost efforts must be made to control the steelmaking variables to the best advantage of the steel producer. One of the major variables is the slag in the furnace and its effect upon the composition and quality of the metal. What advantages are to be gained from slag control? In the broad sense the advantages must be tremendous, because the very foundations of good steel melting are based on "shaping up" the slag to a point where, with proper temperature, the heat is ready for the final additions. Every melter works toward these ends through his experience with innumerable heats of steel. The elimination of undesirable constituents such as phosphorus and sulphur is entirely a matter of slag composition and physical nature, a point well known for over half a century. The role played by the slag in assisting in proper heat transfer from roof and flame to the steel has been equally well known. In more recent years there has come the problem of oxygen control in the more accurate gaug-ing of additions for making high-grade rimmed steel for the new strip mills, and in the deoxidizing additions for grain-size control and cleanli-ness of forging steels, both carbon and alloy. In this problem the oxidiz-ing characteristics of the slag are of prime importance.

Jan 1, 1940

By M. Zamalloa

Slag foaming is an important phenomenon in many metallurgical processes. It creates large surface areas for multi-phase reactions to take place. In other applications, it protects electrodes and improves the energy efficiency by reducing radiation from hot surfaces. However, it may also be a source of serious disturbances. To control and optimize the use of slag foams, an extensive knowledge of the factors controlling the foam formation and stability is required. Slag foaming experiments were carried out using synthetic FeO-CaO-Si02 slags at temperatures ranging from 1200 to 1350 "C. A data acquisition system was used to continuously measure the foam height, gas flow rate, bubble frequency and temperature. The experimental results show that the gas injection rate has a strong effect on the behaviour of slag foams. At high flow rates and rapid bubbling, unstable foams with short decay times were created. The addition of P20, favours the foam formation and stability by lowering the surface tension of the slag. The average foam life increases with decreasing basicity (CaO/Si02). It is proposed that this is attributed to the increase of the surface viscosity due to surface adsorption of a thin film of silica, retarding the drainage of the liquid films.

Jan 1, 1992

By Arthur W. Cooper

This paper contains a review of the development of blast furnace? slag handling and processing technology in the Ironmaking industry over the past 30 years, with an emphasis on economic and environmental factors. The requirements and practice of air-cooling slag for use as aggregate and of pelletizing and granulating slag for use in cement manufacture are described. The operation of slag pits, slag pots or ladles, the slag pelletizer and early granulation systems are compared with the new continuous .granulation, dewatering and handling systems developed in the past decade.

Jan 1, 1992

D. J. DEMOREST,* Washington, D. C. (written discussion ?).-This paper is a real contribution to technical science; it will make it&apos; easier to think accurately about the inner workings of a blast furnace. I was rather surprised to read that the authors regarded as a new discovery the idea that a molten mixture of CaO, A1203, and Si02 is a molten solution of the compounds of these oxides rather than of the oxides in each other. Surely no. chemist with an active respect for the known facts of chemical affinity could believe that these oxides could be melted together without forming compounds, and that these compounds would then dissolve in one another. This work does, however, help to establish what it was supposed must be true. I think it is worth while, in the light of the work of the Geophysics Laboratory, this work of the Bureau of Mines, and that of previous investigators, to visualize what happens as a charge passes down through a blast furnace, thinking especially of the slag-forming materials. These are chiefly kaolin (Al203.2SiO2.2H2O), quartz, and limestone. These substances do not undergo much change until the limestone decomposes at about the middle of the furnace, whereupon the chemical affinities of CaO and SiO2 must begin to he active; especially if there is any amorphous Si02 present. This forms CaSiO3, and the SiO2, CaSi02 and Al2-032SiO2 then come together to form the binary and ternary eutectics so well located by the work of the Geophysics Laboratory. No matter how much lime has been charged into the furnace, the formation of this eutectic will start it about the same height in the furnace and the gangue will start to get pasty at the same height. If the charge is such that the

Jan 4, 1918

Although the mining industry has achieved record-low fatalities and injuries for each of the last three years, there are still too many miners injured or killed in this nation ís mining operations. Many mining injuries or deaths might have been prevented by using risk assessment to identify and control or eliminate the hazards associated with a task. To focus attention on the importance of conducting risk assessments in keeping mining workplaces safe and healthful, MSHA introduced this initiative on October 12, 2004. This initiative is called SLAM. SLAM is an acronym for Stop, Look, Analyze, and Manage. The steps involved in SLAM are: Stop ñ stop and consider the work involved Look ñ look for and identify the hazards Analyze ñ analyze what needs to be done Manage ñ manage safety by developing and implementing controls Everyone should be aware of the risks of an accident before beginning a task. It may not always be obvious that performing a seemingly routine task could result in an accident. That is why conducting a risk assessment is so important. Itís important to remember that over time a mining workplace seldom remains unchanged. Risks must be assessed whenever procedures or processes change, whenever new tasks are started, or non-routine tasks are performed.

Jan 1, 2005

By Klaus Gamweger

"This paper introduces an innovative solution to open and close the tap hole of different furnace types in the copper industry with a slide gate system. Two plates with defined drilled holes are slid against each other, which enables effective starting and stopping of the copper flow as well as throttling. Typically, the copper is poured via a tap hole into a launder system by rotating the furnace into an appropriate position. Control of the casting rate is also performed in this manner. Or, in case of stationary furnaces the tap hole is opened by oxygen lancing and closed manually with a clay- or copper-cone. These procedures show a lot of disadvantages including splashing, oxygen pick-up, and energy losses as well as a severe danger for the working staff. All these problems can be overcome with an appropriate slide gate system.IntroductionThe control of the casting rate of a copper anode furnace usually is performed by rotating the furnace into an appropriate position. This implies that the taping starts with the tap hole at a very high position. Copper splashing and an uncontrolled oxygen pick up are - with several more disadvantages - the consequences. RHI AG has developed an innovative solution for copper applications to open and close the tap hole with a slide gate system which allows also an accurate control of the flow rate. By using this system it is possible to start the casting procedure with the tap hole at the deepest position, directly above the launder. This paper presents this new slide gate system in detail and shows the advantages in production and safety issues."

Jan 1, 2012

By W. D. Freeborn

Slim-hole drilling and completion techniques were first used in the Cynthia area of the Pembina field, Alberta, by the Texaco Exploration Company in the summer of 1957. Prior to that time, eighty-eight wells had been drilled and completed in this area in a conventional manner. Subsequent to the initial four-well evaluation programme, twenty-one additional wells have been drilled using slim-hole techniques. No difficulty was encountered in the drilling and completion of slim-hole wells, or in obtaining production from them. A comparison of drilling and completion economics and practices has been made for slim-hole and conventionally completed wells. Penetration rates for both bit sizes (614 in. and 9 in.) were relatively equal. The shorter life of the smaller bits required the use of 15 per cent more bits per well, but the total trip time to change bits was similar for both hole sizes because of the higher hoisting speeds possible with the lighter drilling strings used in the slim holes and better hole conditions. Completion costs of the slim holes were reduced by 37 per cent as compared to the costs of conventional-type completions. This was made possible through the use of smaller well equipment, the elimination of tubing, and a reduction in rig time for completion operations.

Jan 1, 1958

By Stephen B. Hearn

The SLon Vertical Ring and Pulsating High Gradient Magnetic Separator was developed to overcome multiple disadvantages associated with traditional horizontal type Wet High Intensity Magnetic Separators (WHIMS) which have been in service for many decades for recovering iron ore and other minerals. Proven successful, with hundreds of units now upgrading low-grade iron ores and maximizing recovery of fines throughout China, the technology is now being tested in the Western world. This paper will discuss the drawbacks of traditional WHIMS, explain the operation of the SLon, and illustrate its practical use in processing hematite ores.

May 1, 2007

By Jed Greenwood, Lyall Workman, Michael Haggerty, Russell Sheets

Draglines often work from a position on the active highwall or spoil side bench to remove undisturbed waste material and spoil in the previously mined pit. To protect the dragline crew members and the machine, it is necessary that the highwall remain stable while the dragline is present on the bench. In the past several years, we have been involved in determining the causes for highwall failures that included the dragline. While there have been no injuries and limited dragline damage with these incidents, the potential certainly exists for a more serious outcome. In all cases, the operation had completed a geotechnical study to support the ground control plan and pit designs. However, all these incidents included aspects that would not likely have been identified in studies to determine highwall and spoil designs to support ground control procedures. In general, these events included aspects that were localized and would have been difficult to identify in initial slope stability studies either observationally or during the soil testing and modelling efforts. Although the authors do not have quantitative evidence of this, it does seem there has been an increased number of events in recent years. This may be due to loss of institutional knowledge, mining in more challenging areas, or simply an increase in localized variation. This paper will describe some of the issues we have seen and what the causes of failure were. It becomes clear that avoiding similar incidents in the future requires on-going observation and inspection of active highwalls and spoil benches to try and identify local variability and impact on mining. The information can proactively be used to update stability modeling of any concerning issues to determine likelihood of problems and to develop solutions.

Feb 1, 2025

By L. H. JEFFRIES

In the mining operations of The Canyon Corp., Deadwood. S. D., the use of mucking machines has been of definite advantage. The type used is that which depends upon the traction of the motor-driven wheels to crowd the dipper into the muck pile, while the car in which the muck is received is coupled to the mucker and moves forward or back with it. This general arrangement is entirely satisfactory on a substantially level track. The ores which occur in this district are a replacement of dolomite and the beds are now tilted to an inclination of about 7-1/20. In our operations it is necessary to drive inclines down-hill on this slope, which makes a difficult hand-mucking job even if water were not present. With these facts in mind, an attempt was made to use the mucking machine for driving down the in- cline, but as expected, the traction was insufficient to handle the machine and the necessary car. The means used to correct this condition will perhaps impress most readers as too complicated and cumbersome to effect any economy, but the idea may be of service to some who have a similar condition. After considering several s

Jan 1, 1940

By Manuel Rapiman, Ricardo Sepulveda

The feasibility study of Escondida Norte (ENorte), recommended a slope angle design for the Final Pit. But, according to the experience obtained with the slope adjacent to the West wall of ENorte, in which Compañia Minera Zaldívar (CMZ) gained in its phase 4, a slope of similar geotechnical characteristics will be exposed in the West Wall of Phase 1 (Premine) and of the Final Pit, with an interramp angle 53º and with very good stability results. In this regard, Minera Escondida Ltd. (MEL) performed a study of the slope angles for the phases mentioned and according to this delivered the results of this evaluation, the recommendations and/or the necessary conclusions in the design to ensure that the slopes are stable enough and may enable safe operational management of them.

Jan 1, 2006

By Dan Mahrt

"In June of 2009, a slope failure occurred along River Road in Bismarck, North Dakota. The slope failure affected approximately 300 feet of River Road with vertical displacements up to 3 feet, resulting in closure of the road. River Road travels along the Missouri River in Bismarck in a geologic area riddled with historic slope failures of varying sizes. River Road is a city roadway which travels along the Missouri River. The toe of the failure extended into the Missouri River, therefore methods to repair the slope needed to be constructed within United States Army Corps of Engineers (USACE) requirements, and be acceptable to the City of Bismarck. As this is a scenic area along the river, the stakeholders desired to maintain the scenic landscape along the roadway as a part of the slope stabilization.Due to the magnitude movement of the failure mass, the geometry of the failure was relatively easy to evaluate. In evaluating remediation options and collaborating with the USACE, the team determined that the scarp was situated primarily within the navigable portion of the Missouri River. This required USACE approval for any repair or remedial work downslope of the roadway. The City of Bismarck wished to reopen the roadway as soon as possible, therefore stabilization options were limited to working within the road right-of-way to avoid permitting for working within the navigable waterway.The remediation solution for this project involved a combination of driven H-pile and placement of lightweight fill to re-construct the roadway at the original grades, and avoid impacting the navigable portions of the Missouri River. This paper discusses the unique project constraints and the innovative solution using multiple technologies to successfully stabilize the slope.BackgroundIn June 2009, Bismarck, North Dakota experienced two consecutive days of significant rain resulting in over 5 inches of precipitation in a 36-hour period. Shortly after these rain events, a slope failure was noted on River Road, a city street along the Missouri River in Bismarck. Initial findings noted the slope failure affected about a 300-foot long portion of the roadway, with vertical displacements of about 2 feet. The city of Bismarck closed the roadway and began evaluating repair solutions for the road."

Jan 1, 2016

By D. L. Pentz

The use of "probability" methods in slope stability analysis has been practised by geotechnical engineers for some time. This paper questions whether the term probability has been properly used since in many cases the term is used in a classical statistical manner only to describe frequency distributions of data. This paper proposes a definition of the term probability which includes the engineers&apos; subjective state of confidence for all critical parameters. Such parameters may include the slope stability model, undetected structural features, strength, groundwater pressure distribution, and geological framework. This process does not make a "better" analysis but it does force the geotechnical engineer to state his opinion in such a manner that others can understand and if necessary, criticize the assumptions. Further, this technique forces the question, "What impact would failure of a slope have on the production schedule or costs of a mine?" The level of risk taken in adopting a particular slope design strategy in a mine is not a question of what Factor of Safety should be selected but, rather, what trade-offs result from steeper slopes and the associated costs of failure. This paper also presents several simple probabilistic techniques which, though widely used in other fields have been all but ignored in geotechnical slope stability analyses. These include the use of stratified sampling to optimize Monte Carlo uncertainty approaches, and the use of simple functional approximations rather than complex stability models in probabilistic analysis. The author presents a case example of this technique and discusses the results in comparison with more traditional methods.

Jan 1, 1983

By Joseph W. Siefke

The Kramer borate deposit is located in the western Mojave Desert at Boron, California, about 100 miles northeast of Los Angeles (Figure 1). The deposit derives its name from the district in which it lies. Borax (Na2 B407.10H2O) is being mined from the Boron open pit to serve a major portion of the United States and world borate markets. This paper deals primarily with those geologic factors which affect slope stability in the overburden at the Boron open pit. Discussion includes slope failure history, slope monitoring techniques and the results of a dipmeter survey of overburden structure. Open pit mining was begun at Boron in 1957. The initial pit was successfully excavated at the recommended 1.5:1 (horizontal to vertical) slope in the overburden. During pit expansion in 1962, excavation of the overburden exposed beds dipping into the pit at +15 degrees and numerous high angle fractures associated with two intersecting fracture systems, the West Jenifer and Portal fault zones. Ensuing south and east wall failures indicated the need for more structural information in the arkose to establish better wall design criteria. Barnard and Kistler (1963) recognized that the many facies changes, faults and other variables in the Boron overburden make it extremely difficult to reduce prediction of slides to a simple arithmetical formula. Despite the difficulties and uncertain¬ties, special programs such as surface resistivity, refraction seismic and core drilling were conducted in an attempt to predict slope stability conditions and to gather geologic information. These early efforts while helpful, did not provide the necessary details of bedding orientations and fault locations which are of paramount importance in our slope stability program. A dipmeter survey in 1974 successfully measured these variables and data from that survey are instrumental in the design of slopes currently being excavated.

Jan 1, 1976