Search Documents

By Harry M. Parker

Exploration for sandstone-type uranium ore bodies which will be exploited using underground mining techniques is usually executed in sequential fashion. Geostatistical methods can be used at the earliest exploration stages to design drilling programs which have a high probability of success in the location and delineation of mineable ore-grade mineralization, should such mineralization exist. In succeeding development stages, geostatistics may be used to outline and define the potential grade of reserves and to apply confidence limits on the grade estimation. Delineation of mineable reserves for mine planning requires extensive development drilling; using such drilling data geostatistical methods may be used to minimize the drilling needed to achieve a desired level of confidence in the calculation of mineable uranium ore grade and tonnage. Because sandstone-type uranium deposits tend to be pod-shaped and are generally aligned along a mineralized trend, this paper proposes a geostatistical method of calculating uranium ore reserves which accounts for this fact and predicts the area within a trend which is underlain by ore. This method uses an indicator value; that is, drill holes which contain mineable ore-grade intercepts are coded as 1, those that do not are coded 0. The indicator may be kriged over the mineralized trend to obtain an estimate of the area underlain by ore. The thickness and grade-thickness may be kriged, and the average ore grade may then be obtained by dividing grade-thickness by thickness, as is conventional for stratabound deposits. The mean grade is then multiplied by the kriged mean thickness to obtain an estimate of the volume, and thence tonnage, of mineable ore within the trend.

Jan 1, 1979

By P B. Hills, R J. Walton

Geotechnical instrumentation has been implemented as a key step for monitoring and optimising an engineered mine design for managing seismicity at the Beaconsfield Gold Mine. Measurements of displacement, stress change, ground control element load and seismic response of the rock mass allow for back analysis and calibration of critical parameters for feedback into the engineering design loop. Instrument clusters are installed in strategic locations prior to the commencement of stoping in order to determine the nature of the response of the rock mass to stoping. A selection of instruments including instrumented cable bolts and rod extensometers, resistance wire extensometers, hollow inclusion stress cells, vibrating wire stress meters and resistance wire extensometers are used to gather data through a data logging system. The rate at which data is recorded is adjusted to provide more information during periods of anticipated rapid change such as around stope firings or during periods of high seismic activity, and less information during periods of anticipated quiescence. The twofold purpose of the instrumentation is to calibrate the numerical modelling output which forms the basis of the engineered mine design, and to provide an alert mechanism where the behaviour of the rock mass is not what was anticipated, or where the impact of that behaviour may compromise the integrity of the engineered ground control system. The paper describes the location of instrument clusters with respect to stoping, the type of instruments employed and the method of data acquisition. It provides examples of results obtained and illustrates the way in which that information is used to optimise the mine design and manage seismicity.

Jan 1, 2008

By R. H. Sergent

The interest in using halogens for extracting precious metals from ores has increased due to changes In ore characteristics, environmental concerns and regulations. The rediscovery of halogen leaching capability has been the topic of these and other writers1-30. Much work has been done on the performance of bromine, chlorine and iodine5-29. Of these, bromine and chlorine look most promising. Iodine is quite expensive and sometimes forms an Insoluble film on a precious metal surface22,23. Little experimental work has been published on the relative performance of bromine versus chlorine. The Pourbaix diagrams for the halide leach system (see Fig. 1-4) Indicates a significant stability advantage for bromine In forming complex ions with gold. This should result In greater extraction of gold under similar leach conditions and Is evaluated In this work. The regeneration of halogen from a spent leech solution is a critical requirement for an environmentally acceptable halogen leach process. Bromide can be oxidized In-situ to bromine ~ adding chlorine or ozone2,31. Bromide like chloride can be oxidized In an electrochemical cell to produce halogen on demand 13,15,17. Bromine clearly offers a number of possible regeneration pathways. This work strives to compare the relative ability of chlorine and bromine to extract gold from partially and fully oxidized ores. A commercially pressure oxidized sample was evaluated under a number of experimental conditions. The autoclave feed ore from the same mill was also evaluated after complete oxidation In a laboratory autoclave.

Jan 1, 1993

By G. Johnston, J. Greenly, R. G. Buchheit, D. C. McIntyre, R. Muenchausen, D. J. Rej, R W. Stinnett

"Rapid thermal treatment of materials using high energy, high flux, pulsed ion beams can produce modified surface layers with unique microstrutures and properties. High energy ions loose their energy during the slowing down process in the workpiece and thus deposit their energy continuously over a depth of a few microns. The deposition of energy can lead to melting and in some causes ablation of the heated layer. Because the pulse duration of the ion beams is typically only 50-200 ns, steep thermal gradients generated during heating facilitate rapid cooling (107K/sec-108K/sec) of the treated layer by thermal diffusion into the underlying material. Rapid heating and cooling of materials can generate surface layers with non-equilibrium amorphous or nano-crystalline microstructures that exhibit increased hardness, wear resistance, and corrosion resistance. Pulsed ion beam treatment can also lead to surface smoothening or can be used to mix thin « 1 11m thick) coatings into underlying substrates. Pulsed ion beams can be generated using existing ""flashover"" ion source technology which is capable of producing single shot, mixed C, H, and O ion beams with beam cross sections of approximately 100 cm2 and energy fluxes up to 100 J/ cm2. Recent advances in repetitive high energy pulsed power technology and development of magnetically confined anode plasma ion sources have facilitated the development of ion beam systems that generate single species beams that pulse continuously at 120 shots/second. These capabilities will allow rapid treatment of large surface area workpieces at low cost.IntroductionThe rapid solidification of liquid materials can create unique materials and material microstructures that often have properties that can lead to enhanced performance. Rapid solidification processing of the surfaces of materials using continuous and pulsed laser beams (laser glazing) has been explored for over 20 years (1-5). Advances in high energy, pulsed electron and ion beam technologies over the past decade have provided rapid thermal treatment techniques that may be less expensive to impliment than laser surface treatment for many surface modification applications (6). High energy pulsed ion beams have recently been used to harden aluminum(7), copper(8) and tool steel surfaces (6,9), increase corrosion resistance of Al alloys (6), mix coatings into underlying substrates (10), and create amorphous films (11,12)."

Jan 1, 1994

By P. N. Calder, D. B. Apel, S. D. Butt

Mine-wide (MW) microseismic systems use widely spaced transducers to determine the source location and parameters of stronger microseismic events, while high frequency (HF) systems use fewer transducers to monitor local areas for the weaker events that can precede stronger events. Previous monitoring at the Creighton Mine indicated that an HF transducer located 120 m away from an active stope recorded two types of activity in response to production blasting: the first occurring at the same time as the production blasts and associated with the passage of the direct seismic waves from the blast through the local area, and the second occurring several hours later and associated with the arrival of a slower moving stress change through the rock mass (which was identified by the mine’s MW system). Interpretations of locally increased stress levels, based on analysis of the recorded HF events, correlated with the nearby occurrence of two strong seismic events. These results were applied to a similar monitoring trail at the Kidd Creek Mine where the transient stress changes induced by several development blasts were monitored. It was observed that increases in HF activity corresponded with the occurrence of MW events near the transducer location, and that fewer HF events were recorded the longer this occurred after the blast. Local geological features appeared to influence the number and occurrence of both HF and MW events.

Jan 1, 2000

The paper describes data from test work programs on a range of magnetite ores in Australia and overseas. The analysis looks at the behaviour of material of different sizes fed to the rolls and the change in product size as a result of that, the conclusion being that there is a logarithmic relationship. The paper develops a form of equation to predict the product size from a given feed size distribution. The behaviour of the various magnetite ores is compared to more standard test methods such as crushing work index and unconfined compressive strength.

Jan 1, 2009

By G Hall

BHP BillitonÆs (BHPB) Yandi ore deposit is a channel iron deposit (CID) in the Pilbara district of WA. The ore is predominantly a goethite-hematite pisolite and overlays a clay at the base of the deposit. Knowledge of the location of the contact prior to mining is critical to maximise ore extraction and minimise contamination from and mining of the underlying clays which contain high levels of alumina. The contact between the iron ore and the clay is highly irregular. Traditionally the contact has been delineated by closely spaced drilling û this can be expensive and since each drill hole only provides a point sample measurement, irregularities in the contact surface can be missed. In September 2001, three high resolution geophysical techniques were trialled to see if they could be used to improve the efficiency and accuracy of ore delineation. The three techniques were resistivity imaging, ground penetrating radar and electromagnetic conductivity imaging. The resistivity data showed a favourable correlation with the available ground truth data from drilling. Using this ground truth data as a calibration, an interpretation of the depth to the base of the channel iron deposit (CID) ore was constructed for the areas surveyed. A significant attribute of the method is that the position of the base of the ore is imaged continuously along the lines that are surveyed rather than at discrete points. No continuous well defined ground penetrating radar (GPR) reflections were observed from the base of the CID ore. There did appear to be some correlation between the range of echo times that reflections were observed and the drill data, however the precision to which the range of echo times could be estimated was of the order of several metres and therefore not adequate to replace current procedures. The electromagnetic data showed good correlations with the existence of shallow clays but did not discriminate between variations in CID ore depth. This technique is therefore not suitable for mapping the base of the CID ore but may still be useful as a rapid tool for mapping the position of clay bands.

Jan 1, 2002

By P Corbett, P Sheffield

Centennial Coal operates the Springvale longwall mining operation which extracts coal beneath the Newnes Plateau in the Western Coalfields of New South Wales. Springvale, and the neighbouring Angus Place mine, have a history of difficult geotechnical conditions where combinations of a relatively high stress regime and weak, laminated roof and extensive geological faulting has led to numerous roof failures throughout the mine’s life. Following development, the mines underground roadways can experience high levels of roof movement which may lead to roof falls. Multipoint wire extensometers are extensively used throughout the mine for roadway condition monitoring, and to reactively drive remedial strata support through trigger action response plans (TARPs).As a result of the use of high-density extensometer monitoring over a long period, the mines have an extensive archive of legacy data. Data processing has evolved over time in order to accommodate the increasing data volume, including direct data entry from the recently introduced hard-wired real-time monitoring instruments. It is likely that telemetric real-time instruments will be introduced in the future, which will cause another step change in data management requirements. This paper discusses the transition to and evolution of relational database management systems for extensometer and associated data.This paper also presents case studies of the use of a new software tool for reprocessing legacy data to enable time-scaled visualisation of monitoring data in the context of longwall and development face positions and installed strata support. The software can be used proactively in the identification of geotechnical risk factors and their interaction with the mining process to allow a more robust geotechnical hazard process. It interfaces directly with the widely used ExtoChart database software and can be presented with scale drawings of geological and geotechnical data to allow correlation of monitoring data results with risk factors.CITATION:Corbett, P and Sheffield, P, 2015. The use of high-intensity monitoring data to better characterise geotechnical properties of a non-homogeneous rock mass, in Proceedings Third International Future Mining Conference, pp 145–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

This paper examines the new water-hydraulic (hydropowered) drill rigs that have been developed and proven in the last decade primarily in tabular, shallow-dipping, narrow-reef hard-rock South African mines. These include drill rigs for flat-end tunnel development, narrow inclined raises and winzes, large inclines and declines and longhole-based developments such as ore passes and vent raises. The hydropower technology rigs offer advantages both in safety and performance over traditional compressed-air-powered, hand-held development, and are generally more cost-effective than imported oil electro-hydraulic drill rigs. Furthermore, hydropowered rigs are inherently energy-efficient. The benefits of hydropower are discussed and a ?comprehensive development model? is presented which demonstrates that ore-bodies can be accessed in significantly shorter times. ?Localized? half level hydropower systems are introduced and a range of ancillary equipment available is listed.

Jan 1, 2012

By H. E. Lake

VERY EARLY in the initial stages of underground development work at Eldorado's Beaverlodge operation, the decision was made to use mill tailings as a backfill product. Mining and milling commenced in June, 1953, using locally available sand as backfill, while test work and installation of a plant was carried out to prepare ?and deliver the tailings to the mining areas. The first use of tailings was made in February, 1954, a sandslime separation being carried out with hydraulic cyclones. To date (January. 1956), approximately l 40,000 tons of fill have been used in the stoping areas, providing very effective support in a 50 deg. Vein system of cut-and-fill mining. The recoverable portion of the mill tailings amounts to 40 to 45 per cent, which has resulted in a product giving a percolation rate of 6 to 10 inches per hour. Owing to the fact that Eldorado has milled from 15 to 2 5 per cent more ore than it has mined, through the purchase of custom ore, the degree of control on the sand-slime separation has not been as critical as it might normally be when the filling operation must depend only on the tailings from ore mined. A description of the conditions involved and of the plant as finally installed is given below. It might be mentioned here that, with the impending increase in milling capacity from 700 tons to 2,000 tons p.er day, the present plant will be considerably altered within the ensuing year to handle the increased tonnage and distribution.

Jan 1, 1956

By Gerald P. Kelton

Over the past quarter of a century, the success of the hydrocyclone as a classifier in closed circuit grinding installations has permitted the introduction of the cyclone into virtually all fields of wet industrial processing. Research and experience gained in these applications have established the optimum cyclone sizes and designs necessary to provide the required performance. Although cyclones are used in widely diverse liquid-solid applications, their use for ultrafine separation clearly demonstrates the importance of a familiarity with previous case studies. Krebs Engineers is firmly dedicated to serving the process industry and has acquired the unsurpassed knowledge and experience to handle all types of separations and classification problems. Cyclones have been used for a number of applications to make what might be considered fine separations. A typical example is in an iron ore grinding circuit where a 381 mm diameter cyclone will classify an overflow product to 85% -44 micron. There is no question that this is a fine separation, but still finer separations are possible, and these are known as ultrafine separations.

Jan 1, 1983

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Kellie Provazi

"The purpose of this paper is to study metal separation and recovery from a sample composed of a mixture of the spent household batteries main types, using liquid-liquid extraction and metals electroplating. The electrolytes preparation consisted: grinding the waste of mixed batteries, reduction and volatile metals elimination using electric furnace and acid leaching. From this solution were studied the liquid-liquid extraction using Cyanex 272 [bis(2,4,4-trimethylpentyl) phosphoric acid] with tributyl phosphate as extracting agent. After study of solvent extraction and stripping has been recover and separate the metallic ions and with electroplating was recovered the manganese, copper, nickel and cobalt in their metallic forms.IntroductionCurrently has increased the consumption of electronics devices such as mobile phones, laptops, wireless phones, comcorders, etc., especially portable devices that use batteries as a power source, and consequently has increased the disposal of such material.Increased consumption of this devices is caused by several factors including increased popularity of consumer electronics devices, has become essential of modem life. Therefore, recycling of batteries is important because its reduces the waste of raw materias and nonrenewable resouces used in manufacturing these materias and help prevent potential environmental risks associated with improper disposal of these products together with household garbage.The batteries have a very diverse composition, containing metals such as zinc, lithium, nickel, lead, mercury, cobalt, cadmium, iron, copper, manganese and rare earths. Some components may contain hazardous materials such as cadmium, mercury and lead, and can contain acids or bases.This research line is a pioneer in dealing with a single process for recycling a mixture with all batteries types, for only processes that exist in the world are based on the recycling a mixture with all types of batteries, for only processes that exist in the world are based on the recycling of one or two types of batteries [1-4]. This process necessitates the previous separation of the batteries by type."

Jan 1, 2012

By Don Painter, Nico Sutmoller, Lori M. K. Kahikina, Brian Dorwart

This paper will address the feasibility of using low-density cellular concrete (LDCC) for an annular fill application where project conditions required pumping the LDCC material for distances of up to 16,000 feet. These conditions occurred during construction of the Kaneohe-Kailua Sewer Tunnel in Oahu, Hawaii, between 2014 and 2018. Located on the island of Oahu, Hawaii, this 13-foot-diameter rock tunnel extends for approximately three miles from the Kaneohe Pre-Treatment Facility to the Kailua Regional Wastewater Treatment Plant. The tunnel was built to convey wastewater and provide temporary storage for peak wet weather flows entering the collection system, thereby reducing the potential for uncontrolled discharges. LDCC was chosen for this project partly due to its environmental benefits, which were essential for an application contiguous to the inland marine and coastal waters of the Pacific Ocean. In order to ensure optimal performance characteristics—compressive strength (with a requirement of 300 psi at 56 days), flowability, and light weight—were achieved, extensive testing of various LDCC products and mix designs was completed. The testing measured the initial set time of the LDCC as well as the compressive strength needed to reduce the quantity of grout lifts required for the project.

Jun 13, 2021

By K. U. Kainer

Magnesium and its alloys as the lightest available construction metal offer a wide range of opportunities for the usage in transportation industries, especially Magnesium wrought alloys with their improved mechanical properties show a high potential for structural applications, While magnesium cast components have found their application the interest is now spreading to wrought alloys due to the possibility to get even more homogeneous and better properties compared to cast parts, Therefore alloy and process development especially for extruded and sheet material is a main concern to enhance the application of Magnesium wrought alloys, Castings are still form the majority of applications of magnesium alloys, although efforts to develop adequate wrought alloys have increased, In the presentation, the alloy requirements for processing of cast and wrought alloys will be discussed, The various processing routes and alloy compositions result in specific microstructures and properties which determine the potential use of these alloys, Today, the spectrum of available alloys covers standard alloys as well as alloys for use at elevated temperatures, The trend will be to further diversify the alloy compositions and to improve the alloy properties, Areas of concern still remain the wrought processing and the high temperature (creep) and corrosion properties of magnesium alloys, Examples of recent developments in these sectors will be given, The presentation will also provide an overview of the historical and current use of magnesium and an outlook on future applications.

Jan 1, 2006

At Bulong, the mineralised (>0.8 per cent nickel) ore exists within numerous lithologies, which can and do occur coincidently. It is very important to discriminate between the different host units for estimation purposes, stockpiling and scheduling. This allocation of host unit has relied upon visual interpretation by the geologist recording the information, which can be very subjective by its nature. By using quantified constraints, such as assayed magnesium oxide and iron, the subjectivity of describing the host material of nickel laterite ore is reduced. The constraints permit consistent identification of the various host units, which improves the confidence in the overall estimation and scheduling of the ore.

Jan 1, 2000

By J. H. C. Scrimgeour, T. Toong, R. E. Hamilton

"The principles involved in the use and application of mathematical models as an aid to the development of advanced process control computer systems are described briefly. This is followed by a brief survey of known models of this kind for the simulation of mining industry processes.The main part of the paper describes a dynamic model of the flotation process developed by Canadian General Electric. Using flotation rate constants for each species of mineral and gangue, the model provides a numerical solution of the differential equations describing cell behaviour. The cell mode] is used repeatedly as a subroutine in the •over-all-plant model. The features of the cell and plant models are described.Simulation runs from the plant model show stream .assays and other indications of plant behaviour printed typically in 1-to 10-minute steps for several hours of •Operation following typical disturbances such as changes in feed rate or reagent addition rate. The simulation can :Show expected behaviour for both uncontrolled and computer-controlled plants."

Jan 1, 1970

By D. G. Hartley

The major copper loss at Mount Lyell is in the coarsest particles presented to flotation. An analysis of data collected from the five primary and six secondary ball mill circuits showed that grinding was limited by low breakage rates in secondary mills, possibly due to oversize balls. For 5 months, the make-up ball size for one secondary mill was reduced from 50 to 30 mm. Frequent steady-state tests indicated that overall average breakage rates could be increased by about 70% using smaller balls. A mathematical simulation of the whole circuit with increased breakage rates showed that the resultant finer grind was likely to improve copper recoveries by about 22.

Jan 1, 1981

By Mark E. Gershon

The development of long term plans and schedules for strip mines now faces many companies, especially those developing large properties in the West. The rule of mining the lowest strip ratios first, while delaying equipment acquisitions and recouping investment the fastest, creates the situation where stripping ratios are too high in the latter years of mining operations. A program concept taking life of mine return on investment into account is developed in this paper to optimize mine scheduling and equipment acquisition. In addition, quality considerations (heat content, ash, sulfur, washability) can be considered by including the appropriate blending constraints to meet contract requirements.

Jan 1, 1983

By Ernt. W. D.

A membrane based mixed extractant process was developed for selective removal of copper from waste acidic cupric chloride etchant solutions found in printed wire board manufacturing. The process uses a mixture of Adogen 381 (tri-isooctylamine), MOC®-45 (ketoxime) and MOC® 55TD (aldoxime) in a kerosene diluent. The mixed extractants recover the copper from a hydrochloric acid medium and transfers it to a sulfuric acid medium. The process also utilizes unique wetted membranes to separate the aqueous and organic phases. The driving force for these membranes is not pressure but the difference in surface tension between the two phases. By using these membranes, complete phase separation results. There is no physical entrainment contamination as found in conventional systems. The only cross contamination is the solubility concentration of one phase in the other. This however is less than 10 mg/l.

Jan 1, 1998

Discussion -of the paper of I. N. KNAPP, presented at the New York meeting, February, 1915, and printed in Bulletin No. 96, December, 1914, pp. 2783 to 2793. A. C. LANE, Tufts College, Mass.-Is there any noticeable effect in drilling against salt water? Mr. Knapp says that the mud settles very quickly when brine is added-. What is the effect when you strike a strong salt water ill boring? I. N. KNAPP.-You are supposed to have enough mud pressure in your well to keep the saltwater out. I have drilled against what I knew to be 80 ft. head of water, and hot water too at 99.5°; this water did not show until the well was bailed and the mud pressure reduced. HENRY Louis, Newcastle-upon-Tyne, England (communication to the Secretary*).-Mr. Knapp may be interested to learn that the use of mud in drilling through porous strata is much older than lie appears to be aware of. It has been used notably by Honigmann for boring shafts in Holland and in some of the adjoining portions of Germany. At the Oranien Nassau colliery, shafts about 12 ft. in diameter and 425 ft. deep were sunk in. this way-namely, by boring with a rotary borer, a thick mud puddle being pumped into the shaft, so as to maintain a pressure in the shaft greater than the hydrostatic pressure in the surrounding loose sands and thus keeping the sides of the shaft from collapsing. He will find references to this method in Das Abbohren von Schächten; Handbuch der Ingenieurwissenshaften, p. 134, also in the Transactions of the Institution of Mining Engineers, vol. xiii (1896-97), p. 155. The process appears to have been employed even before 1895, though I cannot give the exact date when it was first used.

Jan 5, 1915