Search Documents

The Anglo Platinum Mogalakwena North concentrator was one of the first three hard rock mineral processing applications to utilise a HPGR circuit in preference to a SAG milling circuit. This was driven by the extreme competence of the ore that had given rise to throughput issues on the original South Plant. Despite more than adequate capacity and performance of the individual comminution units, the circuit has struggled to obtain full design capacity. A thorough review of the integrated performance of the circuit revealed a wide range of bottlenecks and underutilised parts of the circuit arising from design issues. Interestingly, the major opportunities lie in materials handling issues and mismatch of loads about the circuit. This paper presents the high-level outcomes and the associated opportunities, and is pertinent to all HPGR circuit designs.

Jan 1, 2012

By E. J. Jacques

A typical problem in ventilation networks with multiple fan systems is the possibility of them interacting. Multiple fan systems are no exceptions in complex tunnels, and may also be met in mines where underground fans are installed. When aiming at controlling a multiple fan system in a ventilation network, e.g. with a view to maintaining an acceptable air quality level, yet at minimum power consumption, transient flow conditions frequently occur. Although in most applications these transients are short compared to the time needed to achieve the planned actions on the ventilation, one should, however, keep in mind that it is important to avoid any bouncing effect between different (adjacent or distant) fan systems. Therefore a simulation of the unsteady-state flows could allow us to learn more about the propagation of transients within the network, and their possible secondary effects Among others, one question that often is raised, is to find out in which sequence and at what time schedule each of the fans in a network should e.g. be started up? Another typical problem, into which an unsteady-state simulation could provide some insight is the following: how should the facilities of variable pitch angle and/or changeable RPM of several fans operating in parallel be handled and combined in order to obtain a flow rate that changes gradually from zero to its maximum value i.e. the sum of the individual throughput flows of all the fans. The literature is not very abundant on the topic of simulating transient flows in networks. There is no doubt that numerical models have been developed (Pollak, Christensen, 1987), most of the time for particular applications (Wala, Kim, 1985), (Tanaskovic et al., 1984), (Schultz, Sockel, 1991), etc. The aim of this paper is to present a model that also simulates one-dimensional compressible flows in unsteady-state conditions with, however, the specific intent to handle networks with more than one fan. PROBLEM STATEMENT The mathematical model chosen to describe the unsteady flows in a ventilation network is based on the dynamic and continuity equations applied to each of its airways. The following basic assumptions are made : - the flow in the airway is considered to be one- dimensional, - - the flow is assumed to be fully turbulent, and hence the ATKINSON equation for calculating the friction losses will be applied. Whether this equation remains valid for transient state flows remains an open question. However, this may reasonably be assumed since the interesting flow frequencies are low. A discussion may be found in (Kämpf, 1987) ; - the airways are assumed to have a constant cross- sectional area along their length. If obviously this would not be the case, it is always possible to subdivide the concerned airway into sections for which the previous assumption holds. Applying the basic equations of mass and energy conservation, the flow in each branch may be described by the Euler equation for Newtonian flows.

Jan 1, 1995

By Y G. Anoman

This paper discusses the operating model within Endeavour Mining Corporation regarding the options of owner mining against contract mining. It’s based on the concept of ‘are we carrying out the most efficient mining’ regarding cost and performance. This question can only be answered through an extensive contract mining tender process and conducting a comprehensive comparison to evaluate the transition viability. Karma mine, located in Burkina Faso, is the subject of this paper. The Tender model included sales of equipment, parts and tooling associated with the traditional Load and Haul Schedule of Rates (SOR). The methodology focused on the structure of the tender process, which consists in the development of a SOR based on haulage profiles and mining schedule. This is a new Endeavour framework that allowed the bidders to compete on an even level. This was performed using a systemic analysis which encompassed all the elements involved in a transition such as the Human Resources (HR), taxes and customs implications, directs and non-direct costs (Finance and interest on assets, depreciation, insurance), contractor risk profiling. It was assessed against the normalised internal pricing tender-based. This paper gives an insight into how a West African mining operation addressed the sensitivities of the HR functions against the commercial aspects. This was one of the most successful transitions in West Africa and was carried out during the COVID crisis. The outcome of this project has created value by detailing a lesson learned model for both commercial and HR aspects. This discusses the commercial comparisons along with the internal model with the underlying HR functions as a risk factor that could have jeopardised the continuation of the operation. This resulted in a smooth transition with the additional cash flow generated by the sale of the parts and equipment turned Karma into a viable operation.

Jun 22, 2022

By T Roberts

The transition of mechanical cooling refrigerants from their inception in the 1800s through to the current day has been driven by several factors. Original refrigerants such as sulfur and carbon dioxide, chloromethane and ammonia, whilst effective came with toxicity and/or flammability issues. In 1930 DuPont trademarked a new synthetic refrigerant known as Freon® 12, this development was the introduction of ‘chlorofluorocarbons’ (CFCs).Throughout the 1930s and 1940s additional synthetic refrigerants were developed, namely Freon® 11 and Freon® 22. Due to their non-toxic and non-flammable characteristics, synthetic refrigerants were extensively used for domestic, commercial and industrial applications for the next 60 years.In 1985, one of the first scientific papers suggested a potential mechanism linking CFCs and areduction in the density of the ozone layer. In 1987 the Montreal protocol is ratified; it is the first UN treaty to be ratified by every country on earth. Due to CFC’s ozone depletion potential (ODP), the treaty required the consumption of CFC’s to be reduced by 50 per cent over the next ten years. By 1996 the phase out of CFC’s (Freon® 12) is completed, the phase out of HCFC (Freon® 22) refrigerants comes into effect.On 1 January 2018 the phase down of HFC’s begins. Whilst having zero impact on the ozone layer HFC refrigerants have high global warming potential (GWP). As we transition through the HFC phase down (2018–2035) we are beginning to see the emergence of what some consider to be the fourth synthetic wave, hydrofluoro-olefins (HFO’s). HFO’s and their blends have zero ODP and low GWP’s, ranging from 150 to less than 1. The reduction in GWP with HFO’s typically comes at the expense of flammability, which is not ideal. Each refrigerant has its optimal application, therefor when considering refrigerant choices for mining systems, a complete assessment of the environmental, health and safety, efficiency and commercial impacts should be considered now more than ever.

Oct 12, 2022

By J B Tucker, A T. McGrath

Situated in north-west Queensland, Australia, the Ernest Henry Mine (EHM) has been producing copper and gold since 1996. Owned and operated by Glencore Xstrata, ore is currently sourced from a newly developed underground sublevel cave (SLC) mine below the old EHM open pit (the pit). Ore feed to the concentrator is supplemented by satellite open pits comprising the Mount Margaret operation.The transition from open pit to a producing underground mine involved a complex extraction sequence for the first two production sublevels on RL1650 and RL1625. Underground mining during cave initiation was further complicated when south wall instability prevented completion of the final open pit shell. The transition mining phase included mass firing of an inclined crown pillar between the initial SLC void and the pit followed by a combination of transverse and longitudinal SLC mining.The inclined crown pillar mass firing was the first significant milestone in the extraction of the transition ore block. Comprising approximately 890 000 t of in situ material; 70 000 m of drilling was charged with 351 t of emulsion and 6026 electronic detonators to initiate the single mass firing. The firing contained five direction changes over 19 seconds making it one of the largest and most complex underground blasts ever conducted in Australia.Risk management was integrated into every facet of the technical and operational planning and execution of the transition mining phase, whilst maintaining daily mine construction and production commitments. This paper provides a detailed overview of the transition objectives and constraints, mining method selection, post mass blast outcomes and the journey ahead.CITATION:McGrath, A T, Campbell, A D and Tucker, J B, 2014. Transition of the Ernest Henry Mine from open pit to an underground sublevel cave, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 297–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By A J. Minns

This paper addresses the question: how can the minerals industry remain viable; viable in the sense that we are able to access land for exploration and discovery, we are able to develop and operate mines (and processing plants) safely and profitably and we are able to close operations in a responsible manner, so that modified landscapes are restored to acceptable community standards?Many of the answers to this question can be addressed through the theme of this conference û that of eco-efficiency. The eco-efficiency concept is very useful, since it does help to translate principles of sustainability into business value at the operational level. To provide some context to how this can be achieved, the paper discusses what is happening at the international level, outlines some key industry initiatives within Australia and then discusses what work is being done within companies.

Jan 1, 2004

THERE are three objectives in translation of works of this character : to give a faithful, literal translation of the author's statements ; to give these in a manner which will interest the reader ; and to preserve, so far as is possible, the style of the original text. The task has been doubly difficult in this work because, in using Latin, the author availed himself of a medium which had ceased to expand a thousand years before his subject had in many particulars come into being ; in consequence he was in difficulties with a large number of ideas for which there were no corresponding words in the vocabulary at his command, and instead of adopting into the text his native German terms, he coined several hundred Latin expressions to answer his needs. It is upon this rock that most former attempts at translation have been wrecked. Except for a very small number, we believe we have been able to discover the intended meaning of such expressions from a study of the context, assisted by a very incomplete glossary prepared by the author himself, and by an exhaustive investigation into the literature of these subjects during the sixteenth and seventeenth centuries. That discovery in this particular has been only gradual and obtained after much labour, may be indicated by the fact that the entire text has been re-typewritten three times since the original, and some parts more often ; and further, that the printer's proof has been thrice revised. We have found some English equivalent, more or less satisfactory, for practically all such terms, except those of weights, the varieties of veins, and a few minerals. In the matter of weights we have introduced the original Latin, because it is impossible to give true equivalents and avoid the fractions of reduction ; and further, as explained in the Appendix on Weights it is impossible to say in many cases what scale the Author had in mind. The English nomenclature to be adopted has given great difficulty, for various reasons ; among them, that many methods and processes described have never been practised in English-speaking mining communities, and so had no representatives in our vocabulary, and we considered the introduction of German terms undesirable ; other methods and processes have become obsolete and their descriptive terms with them, yet we wished to avoid the introduction of obsolete or unusual English ; but of the greatest importance of all has been the necessity to avoid rigorously such modern technical terms as would imply a greater scientific understanding than the period possessed. Agricola's Latin, while mostly free from mediaeval corruption, is somewhat tainted with German construction. Moreover some portions have not

Jan 1, 1950

By Jeff Ardron

Unlike the first predicted deep-sea mining (DSM) boom 35 years, the public response to the re-emergent possibility of DSM is this time round is not entirely optimistic, with serious economic, social, and environmental concerns being voiced. In the intervening years, the troubling notion of the ‘resource curse’ has been popularized, whereby the economies of developing nations rich in natural resources (agriculture, minerals, and fuels), paradoxically appear to fare more poorly than their brethren who have fewer such resources. There have been a variety of explanations and counter-arguments regarding why the resource curse occurs, including how it can be ‘escaped’, and even some disagreement on whether it in fact does occur. Nevertheless, many commentators appear to agree that that the quality of governance is strongly implicated in the socioeconomic success, or failure, of these resource-dependent nations, and could indeed be the deciding factor. Unlike nations with diversified economies, the majority of the income from natural resource economies, in the form of royalties and rents, flows through national government; hence, good governance and fiscal management is of particular concern.

Sep 1, 2014

By B. van der Moolen, P. J. M. Groot

The introduction of liberalisation in Dutch mineral provision has created a lot of uncertainty on how and where to supply for the need of construction raw materials. Some possible effects of this policy shift are: 1. the extraction of materials from small pits with truck transport, 2. an increasing dependence on foreign suppliers, 3. the usage of marine dredged materials, 4. more input of secondary substitutes. The outcome of this policy and the resulting marketbehaviour have consequences for transport and infrastructure and hence for sustainability issues. Mineral provision, on the other hand, is also influenced by the availability of infrastructure. Insufficient transport capacity could hamper the development of mineral projects that render benefits to society. (Even) in a liberalising market for mineral provision, the central and local governments have an important role to play with regard to infrastructure and the effects of transport. Various trends point towards an increasing internationalisation in mineral provision. What will increasing trade and increasing influence of the market mean for transport infrastructure? How should increasing transport be judged with respect to sustainability? In the sustainability discussion these questions will have to be answered on a national as well as on a European scale.

Jan 1, 2005

By Jing G. Yen

When a solid-liquid mixture is conveyed through a pipe,' four hydrodynamic conditions may develop depending upon the properties of the transporting medium, the properties of the transported material, the properties of the pipeline and the flow characteristics. They are classified as homogeneous flow, heterogeneous flow, intermediate flow and saltation. Heterogeneous flow, which is the subject of the present analysis, occurs when solid particles are coarse, of high density, and the mean velocity of the flow is relatively low, such that the combination allows the establishment of a pronounced concentration gradient in the cross-section of the pipe. In this type of system the suspended matter does not change the rheological properties of the conveying fluid, and solid and fluid phases behave somewhat separately. In recent years much work has been directed toward gaining more insight into the hydrodynamics of heterogeneous flow (1,2,3,4,5,) However, almost all knowledge obtained is empirical in nature and limited in scope. Much effort has been extended to collect experimental information on the energy losses associated with systems of slurry flow (6-13) The work of Durand and Condolios(14,15) represents one of the most extensive experimentations in this field. Through systematic test runs, the effects of the major flow-parameters were studied one at a time. From the results, they concluded empirically that:

Jan 1, 1969

By Yogeshwar Sahai

Submerged gas injection into melts contained in furnaces, ladles, or similar transfer vessels is commonly used in industrial practice. In this review paper, conditions leading to gas bubble formation at the nozzle are first summarized. The increasing gas injection rates and other conditions, such as nozzle size, lead to regimes which are commonly known as "bubbling" and "jetting". These are explained. The gas/melt interactions result in energy transfer to the melt. In recent years, a large number of researchers have investigated the relationships between the energy density and the mixing times. Their work is reviewed, and the mixing mechanisms is described. Finally, computational approaches of modeling submerged gas injection are briefly presented.

Jan 1, 1993

By P. K. Songfack

The transport of slurry within the ball mill depends on the peripheral velocity and porosity of the ball charge. Residence time distribution and mill hold up are of-ten used as indicators of the mode of transport. In this work, the transport problem is tackled via direct simulation of the three dimensional motion of the ball charge. In doing so, the following quantities are calculated: (i) ball size distribution as a function of the distance from the feed end of the mill (ii) mean peripheral and longitudinal velocity and longitudinal velocity of balls of different sizes, and (iii) the spatial distribution of porosity within the ball charge. Hence, the problem of transport is handled as a motion of part of the slurry with the ball charge and part as hydrodynamic flow through the porous structure.

Jan 1, 1993

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"Duluth & Iron Range Railroad. The Duluth & Iron Range Railroad was built from Two Harbors to the Vermilion range at Tower, a distance of 67.6 miles, in 1884, and extended to Ely, twenty-one miles east of Tower, in 1888. It was built into Duluth in 1886, and branches were extended from its main line to the Mesabi mines in 1892 and 1893. The original grades on this road are very steep, going north, and in the thirteen miles from Two Harbors to Highland there is a rise of 1,150 feet. A new line between these points has been built with an increase of three miles in distance and with maximum grades of 1 per cent. Duluth, Missabe & Northern Railway. The Duluth, Mis¬sabe & Northern Railway was constructed from Stony Brook to Mountain Iron, a distance of 48.62 miles, in 1892. The Biwabik branch from Iron Junction to Biwabik, a distance of 15.54 miles, was constructed in 1892. The Superior branch from Wolf to Hibbing, a distance of 16.06 miles, was co11structed in 1893. The Alborn branch from Coleraine Junction to Coleraine, a distance of 53 miles, was constructed in 1906. The total main line mileage is 242 miles, of which 82 miles from Duluth to Hibbing is double tracked"

Jan 1, 1920

By Judson C. Higgins

The paper addresses changes in surface transportation methods in the Industrial Minerals business starting with history, the changes to present time including such areas as energy costs, improved highways, changes in regulations and deregulation, and attempts to project future transportation trends. Transportation methods such as rail, piggyback, truck and barge are compared, and their impact on Industrial Minerals producer's costs and profits examined. The customer impact on our businesses due to deregulation is also discussed.

Jan 1, 1983

By W. J. Bennett

"I AM very happy to have this opportunity of speaking to the Montreal Branch of the Canadian Institute of Mining and Metallurgy.I have selected as the subject of my remarks transportation in that area which is at present our only source of uranium -Northwest Canada. Considering the widespread interest in atomic energy, the end-product of uranium, it may be wondered why I have not chosen to speak of a more spectacular aspect of the development. I hope it will be evident from what I have to say that transportation plays a very dominant role in our effort to maintain a continuing supply from Eldorado's producing property at Port Radium on Great Bear lake and from its coming producer at Beaver lodge Lake in Northwest Saskatchewan. Moreover, transportation has such a bearing on the entire mineral development of the Northwest that it cannot help but be of concern to an organization of this kind. Finally, the transportation problem, of which I shall try to tell you something, is quite unique and the story of its solution or partial solution is, I believe, an interesting one.Transportation experience on this continent indicates that the cheapest method of moving freight is still by water -with •rail, highway, and air transportation following, and in that order •of economic significance. Excluding rail transportation, since the area has as yet no railway lines, this order also applies in the Northwest. I shall direct my remarks to the two kinds of transportation which serve our uranium producers -water and air."

Jan 1, 1952

By Norbert T. Rogers

An accepted statement of fact is that, next to agriculture, transportation is the second most important industry in the world. The transportation networks of the United States have greatly contributed to our nation's growth and prosperity. The objective here is to make the reader aware of the need for communication between geologists, mining engineers, purchasing agents, and transportation managers. Only through a cooperative effort is it possible to reap the benefits of transportation in the industrial minerals field. Transportation is often thought of in terms of trucks, rail cars, barges, and covered wagons. There is much more. Corning Inc. Corning Glass Works is a worldwide organization with more than $2 billion in annual sales. It supplies more than 60,000 different products a year to some 47,000 customer firms and millions of individual consumers. Corning operates 32 of its own plants worldwide and is also an investor with a 50-50 or minority position in 24 affiliated companies in 11 countries. Corning competes in four broad business categories: • specialty glass and ceramics; • consumer housewares; • laboratory sciences; and • telecommunications Binding these four sectors together is the glue of technology. Coming's research laboratory, established in 1908, was one of the first in American industry. That early commitment to research has never wavered. Today, Corning spends annually on research and devel¬opment, as a percentage of sales, at double the average rate for all manufacturing industry in the US. Some 1500 scientists, engineers, and support personnel are now employed at the company's research and development centers in the US, Japan, and France. Petalite background A family of materials melted conventionally as a glass, then converted by special processing to a ceramic was invented in 1957. One of the basic minerals in this glass ceramic product is petalite. Petalite is a monoclinic mineral with a framework silicate structure and a low iron content, about 0.06% Fe2O3. Petalite is found in very few places throughout the world and no commercial petalite deposit has been found in the United States. Sizable deposits occur in Zimbabwe, Southwest Africa, Brazil, Australia, the Soviet Union, and Sweden. Coming's purchasing and geology departments located a source of petalite with proven reserves in what was then known as Rhodesia. The supplier was Bikita Minerals. The relationship with Bikita was one in which Bikita supplied bulk ore that Corning processed into a finished material at its US facility. This bulk ore method of shipment resulted in high losses through contamination and processing. It also caused tank upsets at the Corning plant because of iron contamination picked up through the numerous handlings of this product in bulk. The relationship with Bikita continued until 1965 when the white political leadership of Rhodesia declared its independence from Great Britain. This led to the imposition of international sanctions. The sanctions were lifted in 1980 and the relationship with Bikita was reestablished in 1983.

Jan 1, 1989

By J. L. Thornton

Introduction The importance of coal in our economy is well established, but it may not .be so generally realized how important a part it plays in our daily life. Select a product - any product - and, if it is made in America, bituminous coal has touched it first. Everywhere we will find coal, derivatives of coal, or functions made possible by coal. Apart from the well known major uses of coal for domestic purposes, coking, utilities, railways, and manufacture of steel and cement, there are over 200,000 products derived from coal, from lipstick colours to nylon products and perfumes. An item of interest is the recent action of the Canadian Government in voting $90,000 for development of coal deposits in Yukon Territory to make coal available to the settlers in that area. The value of this move, in case of some emergency, is very evident. Coal in its several stages of formation as peat, lignite, sub-bituminous, bituminous, semi-bituminous, semi-anthracite, and anthracite, has been used for centuries. Coal, as such, was not very well known to the ancients. First reference to "magic stone', or coal, was in 371 BC by Theophrastus, a pupil of Aristotle. This substance was said to burn like wood coal or charcoal and was used by the smiths. The first record we have in modern times was in 852 AD, when sea coal was gathered by the cowled monks of Durham, in Britain, and even at that time a major problem was transportation. Our first record of coal in this continent was near Richmond, Virginia, in 1700. Commercial mining was not under way, however, until 1750. The anthracite fields (presumably in Pennsylvania) were opened in 1793. Even so, there was no extensive mining until about the year 1820. The famous Pocahontas coalfields were opened in 1883. The earliest record of coal mining in Canada is about 1746.

Jan 1, 1950

By G. D. TRANT

HOT metal is commonly transported from the blast furnace to the open hearth by one or the other of two general methods: (1) by hot-metal ladles, usually in conjunction with a stationary mixer, or; (2) by means of mixer-type ladle cars, taking the place of both the hot-metal ladles and the stationary mixer. In both cases, the use of transfer ladles for charging the metal into the open-hearth furnaces is necessary. The American Rolling Mill Co. at its Middletown division, adopted hot metal practice on. June 2, 1928. The pig iron is produced' in a .blast furnace about 11 miles from the open-hearth furnaces, and is trans- ported in Pugh-type mixer cars having a capacity of 150 gross tons each. Three cars are in service and handle the delivery of hot metal to the pig machine and the open-hearth furnaces. The capacity of the blast furnace is 550 tons and casts are made every four hours.

Jan 1, 1929

By Frederic Benard

PRIOR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company's smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow-gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of transferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 1 ¼ miles. Although common in steel practice, the transportation of blister copper in this form had not previously been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended on the design and combination used for the particular experiment. The vessel was filled with approximately 2 ½ tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack on refractories. From the information derived, and in consultation with the engineering staff of the supplying company, an order was placed for the first

Jan 1, 1938

By Frederic Benard

PRIOR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company's smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow-gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of trans-ferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 114 miles. Although common in steel practice, the transportation of blister copper in this form had not previously been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended oil the design and combination used for the particular experiment. The vessel was filled with approximately 2 ½ tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack oil refractories.

Jan 1, 1938