Search Documents

Jan 1, 2004

The Tuscarora mining district, which has been highly productive of gold and silver ores in past years, is situated about 50 miles north- west of Elko, Nevada. The town of Tuscarora lies at an altitude of about 6,000 ft on the west side of the Independence Valley. Precipitation, particularly the winter snowfall, is considerably greater than in many other parts of Nevada, and temperatures are lower. From Tuscarora can be seen-across Independence Valley in the mountains to the east, a distance of about 12 miles, the Freeport Minerals Jerritt Canyon mine, which seems to be-destined to become one of the great gold mines in the western hemisphere. Tuscarora, a gold and silver camp, was active from the early 1870s to 1903 and produced about $10 million in those 30 years. Ten major mines and several smaller ones were operated in an area of about 1.45 square kilometers (one-half squaremile). The deepest shafts were only 230 m (750 ft) but most of the ore came from about the 105 m (350 ft) levels. Mineralization above the water table, at about 30 m (100 ft), was mostly native silver and cerargerite with free gold. Below the water table the ore was rich in sulfides including argentite, stephanite, proustite, pyrargyrite, enargite, arsenopyrite, bornite, chalcopyrite, pyrite, sphalerite and galena. A number of the properties contain sizeable dumps of what was con- sidered waste rock when it was mined. These dumps aggregate over 408,000 mt (450,000 st) with one dump, the Navajo, containing over one-third of the total. A few grab samples taken in the summer of 1978 from some of the dumps indicated interesting silver values with minor gold content. AgAu Exploration Ltd., was organized to explore and develop these dumps into a heap leaching operation. In the fall of 1978 a campaign was started to lease, with front money payments on a royalty basis, three groups of claims on which were located a few hundred thousand tons of dumps. In September and October of 1978, a systematic program of sampling was started on the Navajo dump which was most favorably situated in that it was near to an area which would furnish good sites for heap leaching pads. At the time it was fully recognized that sampling of dumps was a most difficult problem. Because of the topography on which they were situated and the manner in which they were formed, each dump required its own special sampling technique.

Jan 1, 1981

By C. G. McLaughlan

The Noranda concentrator was placed in operation in October, 1928, and the object of this paper is to outline operations during the twelve months which have elapsed since that time. The ores milled are massive sulphides carrying copper and gold, and, in certain cases, zinc. These ores have a specific gravity of about 3.8. The average assay of the copper-gold ore so far treated has been 2.0 - 3.5 percent Cu; 0.10 - 0.20 oz. Au; 40 - 51 percent Fe; and 6 - 15 percent SiO2. In this ore the copper occurs almost entirely as chalcopyrite, and the iron which is not combined with the copper is present mainly as pyrite and pyrrhotite. ?some iron is also combined with the silica, the ratio being about 1 to 4, and a small percentage is present as magnetite. The occurrence of the gold has been shown by microscopic work carried out by Prof. L. C. Graton, of Harvard University, to be very variable. Some of it is free, and is included within the base-metal sulphides or occurs at their boundaries. A similar distribution also holds for a portion of the gold which is combined as a telluride. Little is so far known of the occurrence of the silver other than that some of it may be combined with the gold in the telluride, petzite. The copper-zinc ore contains up to 6 percent copper, and has a very variable zinc content. The copper in such ore is present as chalcopyrite, and the zinc as sphalerite. In starting the mill we had three conditions to face; the first of these was climatic, the second was the lack of skilled flotation operators, and the third was the ore itself." The last of these three proved much more difficult to contend with than the other two combined.

Jan 1, 1930

By Oliver M. W. Sprague

THIS gold problem is full of complications and can hardly be handled adequately or comprehensively in any short period of time. Perhaps I might begin by mentioning a few aspects of the subject about which I suppose there will be no disagreement. The first of these is that we already have a stock of monetary gold in the United States far in excess of what is needed to support any desirable increase in the present volume of currency and credit. The second is that this already superabundant gold stock is certain to be considerably enlarged during the course of the war, and presumably during the months of readjustment following its conclusion. Some billions of additional gold, we may reasonably presume, will come into the country during these next few years, thus increasing the aggregate monetary gold stock from the present eighteen billions to perhaps twenty- two or even twenty-five billion dollars.

Jan 1, 1940

By Sheldon P. Wimpfen, Ralph H. Sweefser

FOR centuries the pumping of water has been one of the chief problems to be overcome by the persistent men who win the mineral wealth of the world. Profitable operations have often been forced to suspend activities as the mine penetrated well below the water table or when sudden rushes of water were encountered. To operate below the local water level requires continuous pumping equal in volume to the amount of water flow¬ing into the mine workings. Often the water to be removed exceeds the tonnage of valuable material produced. To be above local water level is a valuable asset. Modern mining practice permits nothing short of the extraction of the last pound of profitable ore from a mineral deposit. In the days before the development of mechanical and electrical power as we know it today. water in any quantity was a major

Jan 1, 1948

By Joël P. T. Kapusta

Back in 1995, Air Liquide and Union Minière presented a joint paper at the Copper 95 – Cobre 95 Conference in Santiago, Chile, describing the first full scale plant trials of shrouded sonic injection in a Hoboken converter at the Hoboken smelter in Belgium. Almost a quarter of a century later, the technology known as ALSI, or Air Liquide Shrouded Injection, has been tested or commercially implemented in several copper and nickel smelters. Despite these successes, the copper industry did not adopt it widely in the same manner the steel industry adopted the Savard-Lee tuyere in the 1970s and beyond, not even in the way the lead industry adopted it with the Queneau-Schuhmann-Lurgi, or QSL, process. The development and implementation of bottom-blowing smelting and converting technologies in China in the last ten years, however, changed the industry’s perception that high- and ultra-high oxygen injection in copper smelting and converting was indeed possible under specific process conditions. In this paper, I retrace the key learnings of my journey with sonic injection over the twenty five years from my humble beginnings in my early years with Air Liquide, through plant trials and technology implementation in the late 1990s and into the first decade of the new millennium, and ultimately, to the most conclusive proof that the sonic injection design methodology I established is valid, and the calculation tools I developed are accurate. I conclude by sharing my thoughts about whether the deployment of the Savard and Lee legacy within the nonferrous industry was just a pipe dream or whether it will become a reality. INTRODUCTION In the context of lower quality ores and changing economic markets, copper smelters need to continuously innovate and improve to remain competitive and respect their corporate social responsibility engagements. One avenue towards this business, social, and environmental goal is to increase process intensity while lowering fossil fuel consumption to lower greenhouse gas emissions and reducing process off-gas volumes to better capture As and SO2–laden emissions. I believe high oxygen sonic injection for submerged tuyere copper bath smelting and converting is one technology that can help smelters achieve that goal of higher business, social, and environmental performance. Twenty five years ago, when I discovered that the Savard-Lee tuyere had revolutionized the steel industry (Savard & Lee, 1966; Knuppel, Brotzmann, Fassbieder, Savard, & Lee, 1972), I had a dream — or was it a vision? — that within the first decade of the new millennium, modern copper smelters operating submerged tuyere bath smelting and converting vessels will have implemented high oxygen sonic injection and will be reaping the financial and environmental benefits that the steel industry enjoyed in the 1970s. As we approach the end of the second decade of the new millennium, I have to admit that my dream has been all but shattered as the majority of copper bath smelting and converting vessels today continue to operate under bubbling regime conditions. This mode of operation is archaic, still requires tuyere punching and blows at inherently low enrichment levels, particularly in converting, producing large volumes of process off-gases. Under such operating conditions, regulations and emission quotas for As, SO2, and particulate matter oblige smelters to use not just primary or secondary hoods, but sometimes even tertiary hoods. I vividly recall being told, fifteen or twenty years ago when visiting smelters to promote the application of the Savard-Lee tuyere in nonferrous processes, that implementing sonic injection was not economically viable due to the high cost of compressing air and oxygen. Some of the smelters I visited back then have since mandated their engineering partners to design and build secondary or even tertiary hoods. I cannot fathom how secondary and particularly tertiary hoods, with all of their auxiliary equipment and added ducting, could be more economically viable than purchasing and installing a few compressors, expanding the pipeline network for compressed air and oxygen, and installing a new control valve train to feed sonic tuyeres. Besides, adding hoods does not address the problem of As and SO2-laden fugitive emissions at its source but merely provides a costly mitigation for it by capturing larger volumes of process off-gases rather than reducing these large volumes in the first place. Moreover, hooding does not reduce energy consumption nor does it increase process intensity, two aspects that I believe are critical for smelters to remain competitive and sustainable in a deeply changing market environment.

Jan 1, 2019

By F. L. Bosqui

NO metallurgical process developed in the last half century has been more widely advertised to both technologists and lay- men, or has done more to promote efficiency and economy in the extraction of the valuable portions of ores than has the flotation process. Practically everybody has heard of this strange procedure whereby the heavy portions of an ore are made to float while the light parts sink. Some- times it is called froth flotation, the mineral-bearing froth being from the first a distinguishing characteristic. Many times it is called oil flotation, because a thin film of oil was commonly applied to the particles to be floated to make them adhere to the bubbles that rise through the pulp to form the surface froth. Oil, though commonly used, is not, however, necessary for this purpose, which is one of the facts that has been learned as the process has been developed.

Jan 1, 1940

By L. A. Cranson

WHEN I came out of Stanford University in 1922, the out-look for men trained in geology, petroleum engineering, and mining was indeed dismal; in fact, so much so that most of us looked upon our future in those fields as pretty hopeless. Neither our professors nor those men in industry with whom we came in contact gave us any enthusiastic encouragement as to the future of ourselves or the fields we had chosen for our labors. I believe that the attitude of pessimism which saturates everyone about graduation time is lament able and short-sighted, and may often start a young man on his way with an attitude of defeatism. Instead, he should be starting out knowing that he can expect hard work and keen competition, but that the fields of his labours are expanding at an accelerated rate, and that strong, energetic efforts will as always accomplish highly satisfactory results.

Jan 1, 1941

By Allen Rogers

TWENTY-FIVE DOLLARS for nothing at all except a sheepskin. That to me is the effect of the New York State law for registration of engineers and the same may be said of any of the state licensing laws. Of course, if one has to practice in more than one state, he must pay a more or less equal amount for every state he works in; and yet there has been little effective protest against these laws. It would seem that the spirit which animated the Boston Tea Party is non-existent amongst engineers. Undoubtedly a good many consider, through their failure to understand the law, that the matter does not affect them. In New York State it is provided that "any person practicing or offering to practice profes-sional engineering or land surveying . . . shall be licensed as hereinafter provided." To quote further from the law: "A person practices professional engi-neering . . . who holds himself out as able to do, or who does, the work that an engineer does . . . " The cunning of the wording of this article can only be appreciated by considering that anyone calling himself an engineer falls within the definition; its liberal inter-pretation (I have not quoted the whole of it) would embrace many who do not consider themselves engi-neers. The state authorities may not construe it to include such individuals; indeed, they may possibly consider it inexpedient to extend it to include engineers of subordinate grade, but the possibility is always there and, even though an engineer be of the grade of assis-tant, he may at any time be called upon to substitute for his principal in responsible charge of the work. It is therefore clear that anyone calling himself engineer and practicing engineering must, for his own protection, apply for registration or run the risk of violating the law. Now, what is the sense of all this? We have done very well without such restrictions on the means of gaining our livelihood. If one only stops to think, there is hardly a minute of his modern existence when he is not dependent for his safety on the engineering by engineers of yesterday or today. How often is one in jeopardy through failure of engineering works, work done under the supervision of those same engineers? If all of us had to wait for our ends by such means, our average life would probably be some thousands of years. Where, then, is the point to the object declared in all these laws that the need for licensing is "to safeguard life, health and property?" Bosh!

Jan 4, 1923

The sixth international symposium on mining with fill nearly coincides with the 25th anniversary of the Jubilee Symposium on Mine Filling. That symposium, held in August 1973 in Mount Isa, in part to commemorate the 80th anniversary of The Australasian Institute of Mining and Metallurgy, was the first in what has turned out to be a very successful series of symposia. Subsequent symposia were held in Sudbury, Canada (1978), Lulea, Sweden (1983), Montreal, Canada (1989) and Johannesburg, South Africa (1993). The series of symposia has now become an established part of the mining industry calendar, and it will be interesting to see which country is given the honour, and accepts the challenge, to organise the next symposium.One way of predicting the future, or some small part of it, is to revisit where we have already been with a view to determining the existence of any trends that may impact on the future. An historical review of filling practice and research, with special emphasis on Australian experience in particular and worldwide in general over the previous 25 years, will enable me to address the historical and predictive objectives. Controversy can always be achieved by producing a best of list; it can be guaranteed that everyone will disagree with at least one of the nominations. On this occasion, the best contributions by individuals or groups in a number of areas of mine fill technology, over the last 25 years, will be the basis for the nominal awards. The controversy can be increased by posing a number of questions that, hopefully, some of the authors will address during their presentations. I imagine the social functions will be busy enough, but the questions may just add to the cut and thrust of the debate.

Jan 1, 1998

The sixth international symposium on mining with fill nearly coincides with the 25th anniversary of the Jubilee Symposium on Mine Filling. That symposium, held in August 1973 in Mount Isa, in part to commemorate the 80th anniversary of The Australasian Institute of Mining and Metallurgy, was the first in what has turned out to be a very successful series of symposia. Subsequent symposia were held in Sudbury, Canada (1978), Lulea, Sweden (1983), Montreal, Canada (1989) and Johannesburg, South Africa (1993). The series of symposia has now become an established part of the mining industry calendar, and it will be interesting to see which country is given the honour, and accepts the challenge, to organise the next symposium. When the chairman of the conference organising committee invited (or was it instructed?) me to prepare and deliver one of the keynote addresses, his request was for me to be in parts historical, controversial, predictive and entertaining. The mix was left to me, with one proviso - that an early pioneer of mine filling in Australia be given due recognition. The chairman of the organising committee alone will be able to determine if I fulfilled the last objective. My success, or otherwise, with the other objectives will have to be judged by my fellow delegates. One way of predicting the future, or some small part of it, is to revisit where we have already been with a view to determining the existence of any trends that may impact on the future. An historical review of filling practice and research, with special emphasis on Australian experience in particular and worldwide in general over the previous 25 years, will enable me to address the historical and predictive objectives.

Jan 1, 1998

By P. K. Sollars, M. A. Alspaugh

In May of 1996, Twentymile Coal Co. began Longwall mining in the Foidel Creek Mine's East Mine District. These Longwall panels are some of the longest in the world (5.48 km/18,000 ft) with very difficult and challenging geometry. The conveyance system is 1,800 mm (72 in) wide, has a 4,500 mtph (5,000 stph) capacity and employs multiple tripper drives. The trippers include traditional powering designs as well as unique regeneration and braking designs. Several components were developed specifically for this application including a mobile tail brake. Control algorithms were carefully developed and tested via computer modeling. A world production record was achieved in the third month of operation and over 1 million tons were mined in June 1997.

Jan 1, 1998

By Hermann A. Derbuch

Twin Mining made a conscious decision when it changed from gold mine explorer and developer to become a diamond explorer in Canada?s Arctic. It was a decision of survival in an environment that saw junior gold companies either disappear or turn into dot com companies. Twin Mining learned fast and staked within weeks of that decision the first 50 sq. km of claims on, what became, its TORNGAT property at 59½° latitude on the east coast of the Ungava Bay in northern Quebec. This land position, 724 diamonds later (including 322 macro diamonds of gem quality, white and transparent) grew to 507 sq. km today. The 74° latitude called when Twin Mining exercised the option to acquire 3 claims owned by Helix Resources Inc. which revealed exceptional diamond potential. A gem quality 5.4 mm (0.768 carat white and transparent) diamond and the discovery of 16 pipes on 15.2 ha convinced Twin Mining?s board to sanction the deal. Both properties have outstanding features. Kimberlite Dykes and Pipes are in outcrop. The property locations have deep-sea access near existing infrastructure. Their locations are in an environment that is stable and development friendly and has a positive track record with successfully operating mines near-by.

May 1, 2001

[ ]

Jan 1, 2009

By Susumu Uchiyama

This machine was manufactured for excavation of the Roppongi station of the Tokyo Metro Line 12. This machine can excavate both the platform and the rail track at the same time in locations where the traffic is congested and has following features: A multi-centered TBM of the size of 7.06(H) x 13.18(W) m The world first H&V TBM, with right and left machine parts articulated vertically and separately for position control A large erector for simultaneous erection of column and central segments of special shape to construct a highly reliable tunnel This paper reports the design concept, construction, and work record.

Jan 1, 1999

By John J. Jonas, Hong Qin

Cylindrical samples of pure titanium were subjected to uniaxial compression at room temperature, leading to the formation of three generations of twins. Many primary contraction twins were observed as the initial texture was favourable for their formation. Numerous secondary extension twins formed within the primary contraction twins and some tertiary contraction twins within the secondary extension twins. The orientations of these three generations of twins were determined by electron backscatter diffraction techniques and their associated Schmid factors (SFs) were calculated. The formation of the twin variants selected in each generation and the absence of certain potential variants are accounted for by rotating the twinning displacement gradient tensor expressed in the twin system reference frame into the crystallographic reference frame of the relevant neighbouring grain. The presence of the observed primary, secondary and tertiary twins is explained in terms of the ease of imposing the required accommodation strains on the neighbouring grains. By contrast, certain first, second and third generation potential high SF twins were absent because their formation would have required accommodation by the most difficult deformation mode: pyramidal glide.

Jan 1, 2015

Leaving the relatively simple life on a uni student and venturing off in to the outside working world is a big step. There are two paths to follow, the æContikiÆ style graduate program where you pick up your new lease vehicle and set forth on two to three years of planned activities, or can pack everything into one bag, stick a copy of æthe rough guideÆ in your pocket, and set off on your own graduate adventure. I took the path less travelled.The less followed method of developing yourself isnÆt for everybody. Parts of the journey are difficult and sometimes it feels hopeless, but itÆs all a learning experience. Along the way you might not get to all the graduate ætourist stopsÆ like dragline, truck-shovel, or drill and blast. But youÆll see most of them and pick up a lot more of the local culture such as people management, operational knowledge, quality control, and the black arts of project financial management.

Jan 1, 2004

By Russell F. Palmer

"THE PRACTISING MINING ENGINEER has little time for the expression of opinion on abstract questions concerning the definition and future of mining engineering. The following comments indicate some of the thoughts and suggestions of those who have found mining engineering a very satisfying field of endeavour. The future of mining engineering has been under discussion for perhaps twenty years. It is significant that the University of Saskatchewan program was in- 88 traduced at the time that some traditional mining schools were questioning the need for mining engineers. One Canadian university, and some American schools, actually abandoned the field at this time, some ten years ago.Five years ago, Mining Magazine sponsored an international debate on training for the future, and concurrently, the CIM undertook a major survey of the mineral industry's manpower needs. The current CIM discussions should prove more fruitful, as they are directed toward mining engineering alone, rather than the broad, and confusing, spectrum of all professionals and semi-professionals of the mineral industry."

Jan 1, 1972

By AIME AIME

MOTHER example of the broad field that is covered by the mining industry is the recent erection by the Phelps Dodge Corp. of a modern hospital building at Douglas, Ariz., and an identical one at the rejuvenated mining town of Morenci. Managers of even small mining properties are often called upon to build schools, houses, stores, maybe a jail, and provide sanitary arrangements, possibly the while acting as mayor of the town. Those who direct larger properties may have to build hospitals, as in the present instance, construct sewage disposal plants, and sometimes even build and manage railroads. A mining camp achieves its reputation among mining men not entirely by the grade or amount of its ore, or the skill of the operating staff in mining and milling it at a profit-the operation soon acquires a reputation as either a desirable or an undesirable place to live, regardless of its remoteness from what is euphemistically termed civilization. Such a community is indeed fortunate if it can boast of a good hospital.

Jan 1, 1940

By Bo R. Arvidson

The strongest magnetic roll separator available on the market enhances certain industrial minerals purity to levels not reached previously. Exceptionally strong forces can also be utilized for processing relatively fine particles at feed rates several times greater than for prior art electromagnetic induced roll separators. Since the unique machine does not work with an air-gap, coarser particles than what has been considered practical can be separated at rates up to 20 tph per single machine unit and 40 tph for a double machine unit. Examples for all these three application areas will be given. While the roll separator can be used only for dry processing presently, the other new separator can be used for both wet and dry applications. It is a medium-intensity, high- gradient magnetic separator employing a filamentary matrix. It was primarily developed for recovery of weakly magnetic iron ore fines, but it is finding applications for cleaning of industrial minerals such as wollastonite, calcite, clay and talc. Its main advantage is a simple design resulting in a very lm cost machine both with regards to total capital investment and operation. A significant technical advantage exists also. The metallurgical performance is similar to conventional electromagnetic separators, while the cost per ton is about half of such separators.

Jan 1, 1985