Search Documents

By N. G. W. Cook

The conventional cyclic system of deep-level mining by drilling and blasting gives rise to an inadequate degree of stope sorting when mining thin reefs. This results in poor utilization of the capital facilities of a mine in the form of shafts, haulages, airways and associated equipment. Continuous and controlled removal of the thin gold-bearing portion of the reefs would permit better stope sorting and hence greater utilization of capital facilities. Results of experiments to develop hard rock cutting machines for mining are reported and the benefits which could be derived from their use are discussed.

Jan 1, 1969

By Robinson Irarrazabal, Edison Collinao, Rodrigo de Carvalho, Patricio Davila, Marcelo Tavares

"In recent years, DEM (discrete element method) softwares, along with 3D laser measuring equipment, have become powerful tools to describe mill charge behavior, as well as forces acting on the liners of SAG mills. With the aim of contributing to streamline this application of the advanced technologies ME Elecmetal and Universidade Federal do Rio de Janeiro, UFRJ, proposed a new approach to improve the design of mill liners using elements from mechanistic modeling of grinding. The paper presents a methodology for continuous improvement of liner design, which uses information from the DEM collision energy spectra in the mill discriminated for the different components (ore and steel balls), as well as information on the breakage properties of the ore being ground. From these it proposes the concept of "effective collisions", which corresponds to the collisions that are of sufficient magnitude to cause breakage, thus allowing to discriminate from impacts that do not cause breakage either in a first impact or after repeated loading. It also tracks the collision of steel balls against the shell in order to assess their potential damage to the liners. An industrial case study is presented of a 38’ diameter SAG mill, which was experiencing challenges associated to liner breakage and low efficiency with the old liner design. Through a modification of the liner design, simulations demonstrated the potential benefit associated to reduction in ultraprojection and improvement in mill capacity. Implementation of the new design in the SAG mill was carried out, resulting in increase in daily throughput from 6 to 12%. Further, the time spent in liner change was reduced by 47% given the reduction in the numbers of parts. This operation also benefited from having no stops due to unplanned shutdowns to replace broken tiles. These demonstrate the benefit of coupling advanced computational tools to sound engineering principles in continuous improvement of liners."

Jan 1, 2014

By J. van Huyssteen, M. Cantor

Newmont Ghana Gold Limited's Ahafo Operation has matured from its project ramp up stage into steady state operations after three years of operation. Management focus has shifted from addressing construction and commissioning problems to optimization and improvement. This focus change has coincided with the introduction by Newmont of a Continuous Improvement (CI) program across the company which provided a project management methodology that can be used in the execution of smaller scale projects. This paper focuses on the application of CI principles at the Ahafo Plant through the discussion of several case studies that demonstrate how these principles are applied.

Jan 1, 2011

By Andrew Dobson, Cheryl Allen, Enrique Acuña

"Totten Mine return air raise was designed with two parallel fans equipped with silencers to reduce the noise emitted from the outlets into the environment. As development and production of the mine progressed through the past years, the silencer system needed to be upgraded, and additional maintenance strategies have been necessary to meet the regulatory noise limits enforced by the province of Ontario. The current mine plan will require the fans to reach the upper limit of their capacity by Q1 2019. To achieve this operational target, additional silencing capability has been required and Totten Mine has explored alternatives to further extend the noise silencing capacity available considering the current constraints at the mine site. The alternatives included a new silencer baffle design and a new layout that have allowed doubling the length of the silencer system. Using acoustic measurement data collected on several occasions, this paper presents and discusses the performance of the various silencing systems which have been installed on the return air fans at Totten Mine.INTRODUCTION Vale Canada Limited’s Totten Mine is a base metal, underground mine extracting nickel and copper, situated in the Sudbury Basin of Ontario. The mine initiated operations at the end of 2013, and is equipped with two main return air fans and two main fresh air fans located on surface. Both fresh air and return air fans are set in a parallel arrangement to operate as integrated units and are equipped with variable frequency drives (VFDs) to allow for the remote modification of their operating set point, usually between 600 to 880 rpm, depending on the mine’s requirements. The main return air raise (RAR) fans are also equipped with dissipative baffle silencers to attenuate the noise emitted to the environment. Approximately four years ago, acoustical measurements conducted to verify compliance with the applicable regulatory criteria, and respond to noise concerns from neighboring residents, concluded that the sound emissions of the main return air raise exceeded the noise design parameters. The acoustic tones of the fans were audible offsite, at a residential location, approximately 9 km northeast of the mine site. The elevated sound levels and offsite audibility was due to degradation of the original discharge silencers from moisture and particulate being drawn from underground workings and passing through the silencer baffles. The audibility was also due to an outlet directivity pattern which directed noise towards the residential location."

Jan 1, 2019

By T. Y. Chong, J. A. Folinsbee, M. Fullam

PJV Dome Mine has used some form of gravity concentration since start of milling operation in 1909 to recover free milling gold. Amalgamation and conventional jigs were first used and were replaced with the Knelson Concentrators in 1993. The Knelson concentrates produced were upgraded on a conventional shaking table prior to smelting and refining into gold bullion. In May 2002, a comprehensive review of the latest gravity recovery technology led to a piloting campaign aimed at further improving gravity recovery. The Knelson concentrates, subjected to intensive cyanide leaching in an Acacia pilot plant, were found to be amenable to intensive cyanide leaching with over 98% of the gold being dissolved within 24 hours. An Acacia Intensive Leach Reactor was successfully installed and commissioned in December 2002, to replace the shaking table. his paper describes pilot scale testing, installation, commissioning and optimization of the Acacia Intensive Leach Reactor. Also, the economic impacts on down stream processes are highlighted.

Jan 1, 2005

By J. Jerome MacDonald, Stephen B. Flewelling

"In the base metals industry of today, operations required to continuously improve productivity and reduce unit production costs. Consistent with these goals is the improvement of the muck haulage cycle from open stopes with the No. 12 Mine.Existing haulage from open stopes occurs with LHD units experience at Brunswick indicates that LHD units have a higher unit cost per tonne mucked than loader-truck combinations when the haulage exceeds approximately 150 m.The reintroduction of open stoping at Brunswick made existing loader-truck combinations unsuitable. It was recognized that application of recent continuous loading technology could potentially result in significant unit cost savings and productivity increases.A review of the technology resulted in the testing of the Voest Alpine AL60 loader in the open stopes located on the 1000m Le vel. Testing began in January 1988 and finished in late November 1988. The test will provide experience as well as quantified production and maintenenace parameters f or the purpose of quantifying production unit costs and system productivity, ultimately resulting in a decision to further utilize or not utilize the loader as a primarymucking unit at Brunswick .INTRODUCTIONBrunswick Mining and Smelting Corporation Ltd. produces approximately 10500 tonnes per day from the No. 12Mine located 35 km southwest of Bathurst, New Brunswick Mining is the largest (single mine) producer of zinc in the world having mined over 52 million tonnes since 1964. Many years of production still remain with proven and probable reserves in excess of 90 million tonnes. Reserves grade at an average of 3.65% Pb. 8.99070 Zn, 99g/mt Ag and 0.32% Cu . The operation employs 1446 people with approximately 800underground including operations and maintenance staff.In the No. 12 Mine two major mining methods are presently utilized . The primary method is Mechanized Cut and Fill (MCF) accounting for approximately 6500 tonnes per day from four major areas. The remaining 4000 tonnes per day is produced from open stopes with the majority of 2800 tonnes per day being produced by the 1000 level.The 1000Level contains 30 million tonnes segmented into open stope blocks 30 m high, 15m and 30 m on strike , with a transverse width of 10m to 50 m (Fig. I). Stopes are organized on a primary secondary stope arrangement along strike. Primary stopes are undercut and overcut full size with the back fully cablebolted. All stope and lateral development is driven 4.0 m high. All stopes to date are flat bottom (Fig. 2). Primary stopes are filled with cemented rock- fill , secondaries with conventional rockfill, Haulage from the stopes is primarily with 8-yard LHD units ; mucking is approximately 50% conventional and 50% remote. Haul distance to date has averaged approximately 150m with current stope haul distances of approximately 300m. Haulage is presently to a small jaw crusher situated on the 1000 Level. From August 1989on, haulage will be to a set of ore passes feeding to a large gyratory crusher situated on the 1200 Level. Start up of the gyratory crusher corresponds to an increase in tonnage from 1000 Level to 4100 tonnes per day."

Jan 1, 1989

By Josh B. Taggart

Some twenty to twenty-five years ago we saw the beginning of mechanization in our coal mines, It has now progressed to the point Chat as instruments of production the pick and shovel are things of the past, They had to give way to better and more efficient methods--so mechanization, followed by and combined with automation, has become common-place in our mines. Our coal could not keep its competitive position without this progress Without it our industry could not look to the future with any degress of confidence. Today we lock back and see cases of regained and salvaged markets. We see better coal products being produced at decreasing costs. We see better utilization of manpower and a stronger, more confident industry, Our hats arc off to those mining men, equipment manufacturers, labor leaders, and others who had the foresight to work toward these ends and the ability to bring them about.

Jan 1, 1962

By John R. Bartels

Jan 1, 2009

By M. C. Mound

A recent development using XRD techniques, a unique fixed detector, specifically permitting full mineralogical information simultaneously for the first time, specially designed sample preparation and presentation system and Rietveld codes provide a continuous real- time analysis on the true contained mineral polymorphic composition of powder streams such as ore materials, cement, ground clinker or any other mineral stream conducive to XRD analysis. There are several COSMA systems currently operating in the US, Canada, Italy and Australia, proving service and reliability of this concept. The mineralogical information generated continuously in real time is used for automated efficiency, product quality and reduces costs. Quantitative Phase Analysis information is transmitted to the plant DCS via Modbus over RS422 or ethernet. Some limited information is stored in the on-board computers for optional future use at the operator?s option.

Jan 1, 2010

By Bob Drew, Goran Vukovic, Bojan Zivanovic, Klaus Gamweger

Reaction bath temperature is a major factor in processing liquid metals and in many applications where a balance between process duration and temperature has to be found to run a procedure efficiently. Also extremes of temperature can decrease the output of a process if too cold or even make it impossible, conversely overheating can be detrimental to both the product and furnace integrity. With the help of the new online temperature measurement system very accurate monitoring of the process is possible in contrast to the current routine practice where the temperature is measured periodically with dip thermocouples. The system works with a digital, fiber optic pyrometer, which is embedded in a refractory housing. Installation in the lining is possible below liquid level as nitrogen is blown to keep the system open and to ensure continuous sight from the optical head of the pyrometer to the molten metal through the tuyere. This permanent temperature measurement gives optimal process control with the potential of taking appropriate actions at an early stage enabling proactive process control. Therefore energy savings and even process endpoint detections can be realized.

Jan 1, 2015

By R. W. Rausch

BELT-CONVEYOR 'history in this country dates back to the end of the eighteenth century. Up to 1896 they were crude in design and application. The second era, dating from 1896 to about 1920, saw special study given to belt construction and idler design. The latter part of this era saw the beginning of the present-day antifriction idler. The third era followed World War I, when industry began to expand rapidly. Mines and quarries, steel mills, and power-generating plants became larger and greater quantities of ore, stone, and coal were being handled. It became vital that belts handle larger capacities, that they be longer, and that they be dependable for 24 hours per day. In this third era a radical change in belt conveyor design and application occurred. The design has became more scientific. Studies have been made to find out what factors influenced the power required for a belt conveyor and it was found that the sag of the belt between idlers and the flattening of the load between idlers had considerable effect on power requirements. So definite initial tension was put into the belt at the loading end and idler spacing was reduced at the foot end to limit this sag. Belt manufacturers made tougher and stronger belts.

Jan 1, 1947

By Bogidar Mihaylov

A laboratory study was conducted on continuous precipitation of copper, cadmium, mercury and arsenic using thiourea, thioacetamide, sodium sulfide and ammonium sulfide as precipitating agents. Depending on the experimental conditions the metals precipitate with the sulfide donors at different orders and rates. These differences were employed as a basis of several techniques for continuous separation of copper and arsenic, cadmium and arsenic, mercury and copper, and copper, mercury and arsenic. The separation of the metals from industrial waste solutions was also studied. The precipitates obtained were inspected using x-ray diffraction, scanning electron microscope, atomic absorption spectrometer and plasma particle counter.

Jan 1, 1992

By C. A. Olivier

Le Ministère des Richesses naturelles du Québec has continued development work on the process/or direct reaction 0/sodium carbonate with lithium-bearing silicates(Canadian Patent No. 643,843). Recent process improvements have involved continuous pressure leaching, rather than batch leaching, and higher solution concentrations (over 55 g/l Li2CO3. These improvements have been demonstrated on a pilot scale operating on decrepitated spodumene from the Sullivan Mining Group's Quebec deposit. The new process is expected to be very competitive with the conventional sulphuric acid route. The improved flowsheet and main process steps will be described along with pilot-plant results.

Jan 1, 1979

By John C. Franklin

A radon survey was made at five different locations in the Twilight mine near Uravan, Colo., to determine chances in radon concentrations in an inactive mine. Data were taken with a continuous monitor set for 1-minute count periods and readings were taken 24 hours a day for 9 days. The 12 readings per station each hour accurately showed how t w radon concentration varied during the day. From the data collected from the intake portal to station 4, the average radon emanation rate was estimated at 18 picocuries per second per square foot (pCi/sec/ft3). A daily cycle in radon concentration was detected that apparently was related to barometric pressure change.

Jan 1, 1976

By F I. Cox, D Peeler, T Bodisco

"Diesel particulate matter (DPM), in particular, has been likened in a somewhat inflammatory manner to be the ‘next asbestos’.From the business change perspective, there are three areas holding the industry back from fully engaging with the issue:There is no real feedback loop in any operational sense to assess the impact of investment or application of controls to manage diesel emissions.DPM are getting ever smaller and more numerous, but there is no practical way of measuring them to regulate them in the field. Mass, the current basis of regulation, is becoming less and less relevant.Diesel emissions management is generally wholly viewed as a cost, yet there are significant areas of benefit available from good management.This paper discusses a feedback approach to address these three areas to move the industry forward. The six main areas of benefit from providing a feedback loop by continuously monitoring diesel emissions have been identified: Condition-based maintenance. Emissions change instantaneously if engine condition changes. Operator performance. An operator can use a lot more fuel for little incremental work output through poor technique or discipline. Vehicle utilisation. Operating hours achieved and ratios of idling to under power affect the proportion of emissions produced with no economic value. Fuel efficiency. This allows visibility into other contributing configuration and environmental factors for the vehicle. Emission rates. This allows scope to directly address the required ratio of ventilation to diesel emissions. Total carbon emissions. For National Greenhouse Emissions Reporting (NGER)-type reporting requirements, calculating the emissions individually from each vehicle rather than just reporting on fuel delivered to a site.CITATION:Cox, F I, Bodisco, T and Peeler, D, 2014. Continuous remote emissions monitoring – the lynchpin for air quality management, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 137–142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By Andre Vien, Jean-François Dupont

"Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the installation and use of such a device on a SAG mill at the Holt-McDermott Mine. Comparison to measured static volumetric load and bearing pressure and inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed. INTRODUCTIONWhile the measurement of load is very important in all kinds of grinding applications, the biggest benefits are expected from AG and SAG milling. This is what motivated Holt-McDermott to take a closer look at this problem, with a view to optimizing SAG mill performance.In many cases, the SAG mill control problem can be stated as maximizing throughput while avoiding a volumetric overload, with the other constraints (e.g. power, grind size, upstream/downstream equipment constraints, etc.) playing a less important role. This is certainly true at Holt-McDermott where the SAG mill is the production bottleneck about 90% of the time, and anything that can be done to increase SAG mill throughput will have a significant impact on operating profit.Although the goal of maximizing throughput while avoiding volumetric overload is simple to state, it has proven to be much more difficult to achieve. The mineral processing industry has expended a great deal of time and effort to devise control strategies in the pursuit of this objective. While much progress has been made, there is still room for considerable improvement. Across the industry it is probably fair to say that overloads occur relatively infrequently, but the real losses accrue as a result of the tendency to run rather conservatively."

Jan 1, 2001

By E. DeLilia

For the past 30 years, surface mines have moved toward more highly mechanized, automatic systems that continuously mine overburden and ore to in-crease productivity, lower operating costs and minimize manpower needs. To achieve these goals, mine operators must be involved in every step of the machine procurement process. Several factors are involved in making the machines operate economically and efficiently: ? Prudent engineering. ? Proper planning. ? Realistic feasibility studies. ? Effective specification. ? Thorough training of the mine personnel.

Jan 1, 1995

By Kyle Selga, Christopher J. Greet

"The Pulp Chemistry Monitor (PCM) has been installed and operated in a number of concentrators in Australasia, and has produced some very interesting results. PCM measures the pH, Eh, dissolved oxygen, temperature and oxygen demand of process streams within a concentrator continuously and in real time.In the example presented in the paper the cleaner feed pulp chemistry is measured, and related back to changes in the mineralogy as well as variations in metallurgical response. For example, a decrease in Eh and dissolved oxygen as well as an increase in the oxygen demand. These changes in the pulp chemistry appear to coincide with increases in the feed grades, probably higher pyrite grades. Further, these variations in pulp chemistry and feed mineralogy have a negative impact on the concentrate grade and recovery.The implication is that if the pulp chemistry is monitored it is possible to predict changes in the mineralogy of the system, and from this the metallurgical response. Further, the changes in pulp chemistry can be used in a control system to counter the changes in mineralogy and maintain the metallurgy.IntroductionIt has long been recognized at a fundamental level that the flotation behaviour of sulphide minerals is dependent on the pH and Eh of the system (for example: Tolun and Kitchener, 1964; Woods, 1976). However, measuring pulp chemical parameters within an operating concentrator has had limited attention. Woodcock and Jones (1970a and b) were among the first to actually collect data from operating plants. Jones and Woodcock (1984) identified some of the chemical complexities of flotation pulps, and noted that most concentrators already operate at high levels of metallurgical performance but there was still considerable scope for improvement. These gains would, in part come from more effective chemical control. In the same volume, Healy (1984) discussed metal ion hydrolysis and precipitation, redox chemistry and how the surface chemistry of sulphide minerals can be influence flotation behaviour. The impact of grinding environment on the pulp chemistry and flotation response of a complex polymetallic sulphide ore is discussed by Forssberg and Subrahmanyam (1993). Their work essentially contrasts the pulp chemical and flotation performance of pulps ground with conventional ferrous grinding media to a fully autogenous system. The data suggested that the reduction or removal of iron hydrolysis contamination from the system could have a positive influence on flotation behaviour, and perhaps the first stage of “controlling” the chemistry of the system should be in the grinding circuit. Grano et al (1995) demonstrated that the collection of pulp, solution and surface chemical data could identify weaknesses within a concentrator, and from these data develop, test and implement solutions that improved the process. Greet et al (2006) showed that the pulp chemical trends observed through primary grinding and rougher flotation circuits of most sulphide flotation concentrators are approximately the same. There are differences in the magnitude of various pulp chemical parameters (pH, Eh, dissolved oxygen, temperature and oxygen demand) as a result of variations in the feed mineralogy and processes employed. Further, it was noted the Eh shifted to more reducing values of the ten days measurements were collected, and this change could be traced to an increase in the iron sulphide content of the feed. Metallurgically, this resulted in an increase in nickel recovery through the recovery of nickeliferous iron sulphides, and a decrease in nickel concentrate grade."

Jan 1, 2016

By J L. Merritt

Contour banks and waterways are standard soil conservation measures to assist farmers reduce the impact of gully erosion on sloping cropping land by reducing the slope length to the interval between the banks. The Universal Soil Loss Equation (USLE) developed by the USA Department of Agriculture Soil Conservation Service in 1930s predicts the long-term average annual soil loss (A).The equation is the product of the rainfall erosivity factor (R), the soil erodibility factor (K), the topographic factors of slope length and angle (L and S) and the cropping management factors (C and P). Contour banks reduce the slope length (L) only.Contour banks are a constructed earth embankment, incorporating a channel on the upslope side, typically traversing a slope on or close to the contour to control and/or prevent the erosion of that slope. The banks are also referred to as graded banks, terraces, or bunds (DSITI 2015). Contour banks are either broad based or narrow based. Broad based banks allow the passage of the machinery over the banks whilst narrow based bank batters are too steep preventing the passage of machinery. Waterways are a stable, longitudinally sloping water disposal area of sufficient capacity used to discharge surplus runoff from the contour bank and to allow it to flow to a lower level without causing erosion (DSITI 2015).The mining industry must decide what the role for contour banks and waterways is in each operation’s rehabilitation and closure plan.CITATION:Merritt, J L, 2018. Contour banks in spoil rehabilitation – a matter of timing, in Proceedings Life-of-Mine 2018, pp 147–149 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By B Broad

"Establishing ventilation in the early stages of a new mine is an essential step to achieve scheduled outcomes that ultimately drive the financial success of an operation. If the primary ventilation is not in place in time to support a contractorÆs work output, then the ore delivery is likely to be severely impacted. Options to increase ventilation in order to address shortfalls are limited. This in turn can lead to reduced revenue generation at a time when a mine is at its highest capital outlay. This can have implications for any company, but even more for an explorer moving to producer. The ventilation put in place to cover the start-up period is also unlikely to cover any extended or increased load required to meet schedule delays.The following paper examines two issues in relation to ventilation with a focus on small to medium projects where the company is establishing a mine using a mining contractor. The issues being: potential impacts on the contract and tender process when using a mining contractor key mine design considerations, such as æcrunch timeÆ, as they interact with ventilation achieving a successful ramp up.A recommendation is made for higher levels of detail around secondary ventilation leading up to the primary fan installation. The information should be included as part of the tendering process and preliminary project execution planning. Understanding the æcrunch timeÆ concept can lead to strategies, as well as back up plans, to minimise any negative impact.By understanding key risks around primary ventilation establishment for a new mine, detailed design work can be completed where it is needed most. Value is added by reducing uncertainty and a payback with better contract terms and a more robust ramp up plan. This will improve the economic return for the company and reduce the risk.CITATION:Broad, B, 2013. Contract considerations and other critical ventilation aspects in achieving a new mine ramp up, in Proceedings The Australian Mine Ventilation Conference, pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 1, 2013