Search Documents

By Gus L. Maciula

Although I will briefly review the current status of coal slurry pipeline technology, I wish to make it clear that this is not a technical paper. It is intended instead to review the current situation on energy resources and requirements, and the environmental, political and economic considerations that mandate a serious consideration of Slurry pipelines as a viable mode of coal transportation into the Georgia and Florida markets. In order to more fully appreciate our current energy situation, it will be helpful to go back a few years and review the evolution of our so-called energy "problem." It was about two decades ago that the first and only major natural gas transmission pipeline was built into the State of Florida by Florida Gas Company. This line was conceived and implemented during a time when gas was plentiful and cheap, and it appeared at that time that unlimited gas reserves were continually being discovered, thus assuring the availability of a clean, cheap fuel and the ,viability of the pipeline system. One of the major factors justifying the original pipeline construction as well as subsequent expansions was a series of long-term commitments under which Florida Gas transported natural gas owned by electric utilities for use as boiler fuel. Thus for the past 20 years Florida industry, commerce, and domestic fuel requirements have been met either directly or indirectly through clean, cheap natural gas which would not have been otherwise available without the pipeline system.

Jan 1, 1978

By Hedge AS

Mt Whaleback is one of the largest open-cut iron ore mines in the world. Haulage cost is the single largest component of operating costs at the mine. Past studies towards alternatives to truck haulage have recognised the potential viability of an in-pit crushing and conveying system, dependent on the proportion of uphill haulage. After seventeen years of mining Mt Whaleback still contains more than 1,000 million tonnes of ore, needing 1,800 million tonnes of waste removal to extract it. What was once a quarry has now turned into a large open pit. The increasing proportion of uphill haulage, the need to replace ageing 120 ton and 200 ton trucks and the necessity of achieving and maintaining a higher stripping ratio prompted, in 1984, the initiation of a new feasibility study into the viability of alternative material handling systems. A semi-mobile in-pit crushing and conveying system was found to be most suited to Mt Whaleback conditions. The East Pit was selected as the best location based on the analysis of haulage profiles measured on long term incremental mine plans. A capacity of 22 million tonnes per year was considered achievable by the proven technology currently available. A detailed estimation of capital and operating costs of two systems - one with trucks only and another with trucks, crusher and conveyor - for the removal of 22 million tonnes per year of waste rock, showed substantial cost savings achievable by the proposed system. An economic evaluation of the two systems established the advantages of constructing the in-pit crushing and conveying system. This is now under construction and will be commissioned in early 1987. Experience gained in constructing and operating this installation is expected to influence decisions on similar installations in future.

Jan 1, 1986

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying methods to prevent workers from being entangled in machinery used at mining operations. An analysis of mining accidents in the United States that resulted in a fatality or permanent disability from 2000 through 2005 showed 438 severe incidents that involved contact with machinery or equipment, an average of 73 per year. Researchers determined that the most common machinery involved in these severe accidents was conveyors. Also, a significant portion of the accidents occurred during machine maintenance and repair. Researchers are focusing on improved methods to prevent unintentional machine startup during maintenance activity and methods to detect workers near moving machine components. One new technology that shows promise for this application is intelligent video. Popular in the surveillance and security industries, these systems use cameras and computerized video analysis techniques to automatically detect the presence of people in preset zones within the camera?s field of view. A preliminary study has been initiated to determine if this technology could reliably detect the presence of workers in hazardous locations near machinery. Possible advantages of the use of this technology include improved detection zone demarcation and improved ability to distinguish between hazardous and non-hazardous proximity, compared to conventional proximity sensor techniques. Initial tests to detect a person near a conveyor system in daylight conditions showed promising results. A description of the technology, test procedures and results, implementation challenges, and future research needs are discussed.

Jan 1, 2008

Some Statistics ? Feasibilitystudiescostbetween2% & 3% of capital andrequire8% to15% of total engineering effort ? Feasibilitystudiesusuallytakebetween8 and16 months ? Historically more than80% of projects fail to achieve all their objectives, usually blame the feasibility study ? What is bankable? Means that your promises will long be remembered. ? Poorly executed feasibility studies ? Driven by inexperience, unrealistic expectations, time constraints, financial constraints, lack of objectivity, front end loading activities incomplete or poorly done ? lack of minimum standard to provide a consistent approach Trend to improve???

May 1, 2010

The purpose of any feasibility study is to determine whether a particular investment or management program will enhance shareholder wealth by, for example, producing an economic return in excess of the cost of equity capital.The threshold rate of return conventionally used in gold feasibility studies is higher than the cost of equity capital, meaning that some viable projects are wrongly described as being sub-economic with their development deferred.Is the industry failing to fully realise its potential? Aside from important technical considerations that determine the cost of exploiting inground inventories, feasibility studies need to incorporate expectations about future gold prices, exchange rates, interest rates and tax rates.Rather than revert to speculation, insights from capital markets give a rigorous framework in which these parameters can be determined for feasibility purposes. Separate questions sometimes, and then inadequately, addressed by feasibility studies include: ò Is it optimum? Many projects are expanded soon after project commissioning - what does this say about the quality of the initial feasibility study? Moreover, does the rate of extraction really matter? ò What is it worth? Although feasibility studies are designed to address viability rather than valuation, such studies are never- theless used by the industry as further evidence that the equity markets have got it wrong again! More likely the problem is with the financial slide rule being used. ò Can it be debt financed? The bankable feasibility study has entered the vocabulary of the gold mining industry but what does it mean? Does it matter anyway how the project is to be Financed?

Jan 1, 1991

By J Kok

"In some underground mines it has been observed that the primary focus during feasibility studies is to determine the best way to mine the defined orebody. Some studies have been conducted without sufficient consideration of the ventilation and cooling requirements or the risk from exposure to associated airborne pollutants caused by the mining operations.Following the hierarchy of control to manage risk, numerous problems of the ventilation systems in some underground mines could have been avoided if sufficient consideration was given to the ventilation requirements to manage heat, airborne pollutants and leakage during the feasibility study phase. If the constraints and hazards were well defined and understood at the time of the study, efforts could have been made to eliminate or substitute the hazards to decrease the risk. Some of these problems include but are not limited to: primary fan locations heat loads diesel exhaust ventilation design based on the production requirement fire/emergency response strategies.This paper highlights areas in the ventilation discipline that are sometimes overlooked during feasibility studies. It will also highlight the importance of the Ventilation Specialist during these studies. Experience and knowledge of best ventilation practices must be applied in feasibility studies.As a result of adequate consideration to all ventilation aspects in the feasibility study phase, risks will become lower in terms of health, safety, production loss and equipment downtime caused by heat.CITATION:Kok, J, 2014. Feasibility studies – what should be considered in terms of ventilation, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 197–204 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By Mark F. Vancas

Virtually every new process plant project goes through the ?Feasibility Study? phase before actually being built. The Feasibility Study is used by the owners and the bankers to evaluate the economics of the project and determine whether or not the proposed investment meets their respective investment guidelines. With a positive result, the project is approved and goes to construction and operation. Then, the actual costs are incurred and these actual costs may or may not agree with what the Feasibility Study predicted. Just how good have Feasibility Studies been? This paper looks at various projects and compares predicted to actual results and also gives information on how to spot a poor feasibility study.

Jan 1, 2003

By Young C. Kim

Use of geostatistics to solve mining problems is gaining importance as the cost of developing new mines is increasing and there is a need to mine more marginal deposits. But, until recently, coal companies have shown little or no interest in geostatistics. However, the stringent quality controls on coal burning has led to a surge in interest in improved methods for estimating clean coal characteristics. Until now, most of the geostatistical applications have centered on the problems of estimating in-situ coal characteristics (Sabourin, 1975; Wood, 1976, 1979; Fang and Stark, 1976; Pauncz and Nixon, 1979; and Knudsen et al., 1980). Little work has been done in applying geostatistics to coal washability, except that by Armstrong (1980). Applying geostatistics to coal washability basically means the estimation of cleaned coal characteristics, with the aid of geostatistics. Cleaned coal estimation plays a very important role in overall emission control strategy, as can be seen by the general flow diagram of such a strategy shown in Figure 1. The scope of this paper is limited to one aspect of the overall emission control strategy shown in Figure 1; namely, the prediction of cleaned coal characteristics using geostatistics.

Jan 1, 1982

By H. X. Li, A. Correa, M. M. Zhang, W. Xuan, M. Andrade

"With increasing demand for steel and depletion of high-grade iron ore deposits, more research efforts are being directed toward extending the life of existing ore reserves and developing technology to treat low-grade iron ore resources. Among all the reported technologies, biotechnologies in mineral processing – specifically bioleaching and microbially induced flotation – have emerged to be considered as low-cost, environmentally friendly potential alternatives to many of the current mineral processing techniques. This paper provides a comprehensive review of current research on the use of microorganisms for iron ore beneficiation and, further, discusses the applicability of bioleaching, bioflotation and bioflocculation for the beneficiation of low-grade iron ores.IntroductionIncreasing global demand for raw materials has led to diminishing resources of high-grade iron ore. As a result, the mining and utilization of low-grade hematite, limonite, specularite, siderite and goethite ores have attracted more and more attention. However, these types of iron ores are of complex paragenesis and fine disseminated grain size, and often contaminated by phosphorus in the form of solid solution. The distribution of phosphorus throughout the iron mineral crystals prevents the effective use of physical separation techniques, and these complex ores are at present largely untapped due to a lack of cost-effective and efficient processing methods. Chemical leaching and roasting-magnetic separation approaches have been mainly tested only on the laboratory scale and are all either cost prohibitive or ineffective when used on low-grade complex iron ores."

Jan 1, 2015

By T. P. Meloy

A methodology is presented for finding feasible or locally optimal designs in the class of homogeneous, countercurrent, processing networks performing two-component non-sharp separations. The advantage of the methodology developed here is that given a set of independent performance criteria (specifications such as network separation factor, beneficiation ratio or recovery), a feasible or locally optimal countercurrent network design meeting those criteria can be found in one step. In the methodology, graph-theory was used to explicitly obtain the exact network responses of specific countercurrent networks. These responses were used to formulate the linear recursion equations whose solution gives the expressions for the countercurrent network responses which are a function of the stage transfer functions for two-component, non-sharp separations. These expressions are also functions of the network variables n and c. These expressions, together with the set of independent design criteria, were solved simultaneously for n and c using the Levenberg-Marquardt algorithm for systems of constrained, non-linear equations. The network variables n and c embody the coded network design information which is used to find the feasible network design which satisfies the set of independent performance criteria.

Jan 1, 1994

By Claiborne C. Van Zandt

THE heavy postwar demand for Portland Cement has created shortages that are gradually being overcome by increases in plant capacity. In the post-war period, the Lone Star Cement Corp. has expanded several of its existing 15 plants and has built 2 new plants, now in operation, with a third new plant under construction in Brazil, of design somewhat different from that of the two preceding ones. The new domestic plants are located at Lone Star, Va., near Roanoke, and at Maryneal, Tex., near Sweetwater, and went into operation during 1951. Each plant is equipped with two rotary kilns and has an initial capacity of 1,500,000 bbl per year, or 6,000,000 sacks. The total cost of each plant was about $10,500,000, and on this basis $7.00 in 1951 money are required per bbl of annual capacity; at 376 lb per bbl, this corresponds to $37.00 per ton of output. The investment corresponds to approximately $80,000 per hourly-wage earner employed. The purpose of this paper is to describe the most interesting design features of the two new and almost identical Lone Star plants. Why the Dry Process Was Chosen The two new domestic Lone Star mills employ the dry process because: 1-The raw materials at both properties are particularly suitable and can be dried very, readily. 2-The Maryneal, Tex., plant does not have water available for slurry. 3-Very substantial kiln fuel savings can be obtained. 4-Dry raw grinding reduces ball and liner wear and- general maintenance, without any sacrifice in power. Operating costs to date have more than justified the choice of the dry process for these two plants. Raw Materials The chemical composition of Portland Cement raw material after crushing, grinding, and mixing, but before burning, is about as follows: [ ] sometimes tailings from an iron ore concentrating plant. Certain objectionable materials occur in raw mix: magnesia, limited in cement to 5 pct, in excessive amounts; alkalies, as sodium and potassium; phosphorous; and sulphur, generally present in coal and oil. The Roanoke raw, materials are dense limestone and shale. The Maryneal materials are soft limestone and a hard brittle clay that can be handled much like shale. Sand and iron ore are required in small quantities. General Plant Layout and Construction The two plants are so similar that one joint description will cover both, with such exceptions as will be especially indicated. The crushing plant is located in the quarry, and raw material is conveyed by belt to the storage building, where all materials are stored and handled. Fig. 1 identifies the various structures of the Roanoke plant. The large storage building is used for the storing and handling of all materials, including limestone, shale, sand, iron ore, coal, clinker, and gypsum. Directly adjoining the storage building is a structure under a similar arched roof, containing the raw and clinker grinding departments and the electrical substation. The discharge ends of kilns and coolers, and coal or gas burning equipment are also placed at one end of the mill building. The 340ft long kilns extend away from the main buildings to form the long leg of an L, at the end of which is the feeding and kiln dust collecting equipment, and the raw blending silos are conveniently located adjacent to the feed end of the kilns. The machine shop, storeroom, electrical shop, foremen's office, service rooms, and meeting hall are combined in one structure in the center of the plant, and the office and laboratory are close by. The cement silos and packhouse do not have to be tied directly into the manufacturing process and are therefore located at a point convenient to the railroad tracks.

Jan 1, 1952

By L. O. Howard

L. D. RICKETTS, New York, N. Y.-The advance which has been made in Smelting has been in the line of cheaper cost of handling, due to larger units and decrease in losses. At the International smelter, Mr. McGregor designed everything to handle the ore under cover. But we do find an unaccounted for loss of 0.7 per cent. of our copper, which is serious. Mr. Wallace has made a suggestion that I think metallurgists ought to know of and think about. He made it years ago-and that is that one of the chief losses is undoubtedly in the charging and discharging of the calcine cars. His idea is that possibly the dryers and heaters might be put immediately over the reverberatories So that they could discharge in conveyors. They could feed on both sides, and thereby the dust raised by discharging in the cars from the hoppers could be overcome. E. P. MATHEWSON, Anaconda, Mont.-I might Say a few words on the plants we have visited So far. I was particularly struck with the cleanliness of the plants, which is next to Godliness. I noticed also that the skull-cracker arrangement they have for handling their converter slag is very good. And they have paid considerable attention to ventilation, and are taking steps to take care of the health of the men. "Safety first" has been well looked after in all the plants we have visited so far. The steel structures are right up to date, and the buildings are of the most modern type, and everything is conveniently arranged. I think the designers of the plants in the Southwest are to be congratulated on what they have done.

Jan 12, 1916

By Robert B. Parsons

"Finance Minister Paul Martin's first budget disappointed almost everyone. The business sector was disappointed at the some what feeble attempt to grapple with the country's deficit. The mining industry was disappointed by tax proposals regarding mine reclamation that fall short of the industry's needs. Has anybody been happy with a federal budget? Federal Budget DisappointsThe federal government's budget papers that were tabled on February 22, 1994, contained a rather bizarre mixture of unrelated tax proposals. The budget signals an unexpected attack on the tax treatment of debt settlements, on certain types of corporate reorgani2ations, and on income earned by foreign affiliates. This is an old style budget, which proposes a pot pourri of technical changes and policy initiatives. Mine ReclamationEffective February 23, 1994, a taxpayer's contributions to a prescribed mine reclamation trust fund will be deductible as a current expense. The budget papers do not provide a definition of what will constitute a ""prescribed"" trust: this definition will surface in due course. However, the budget papers indicate that:• income earned in such trusts will be subject to tax each year;• all withdrawals from the trust (including income already taxed) will be included in computing the income for tax purposes of the recipient;• reclamation costs will continue to be fully deductible at the time incurred; and • contributions, trust earnings, and withdrawals will not be taken into account for the purposes of determining a taxpayer's resource allowance."

Jan 1, 1994

EDITORIAL comments on the anthracite report of the Federal Fact-finding Coal Commission, which became public on July 5, together with an analysis of its more important conclusions, will be found on another page of this issue. In this place, only a few extracts from the report, bearing more directly on technical matters, can be quoted, for lack of space. COST OF MINING Mining cost, as it stands on the books of each mining company, represents the average cost of the total output, all sizes, of anthracite. Egg coal has at least five times the market value of barley, but these' sizes are mined together and their costs can not be separated. Mine costs directly reflect the conditions under which these deposits of coal are recovered. Even within the few counties in which anthracite is found there is a conspicuous range of natural conditions. The distinc-tion between the Northern, Middle, and Southern field, or, as they are also termed, the Wyoming, Lehigh, and Schuykill regions, is primarily geologic and topo-graphic, but the effects of the natural conditions largely control costs. The contrast is great between Some of the level-lying beds of moderate but fairly constant thickness under the broad Wyoming Valley, where mining and underground haulage present relatively simple problems to the engineer, and the steeply pitching or overturned and faulted beds of variable thickness in the Schuykill field, where crushed coal' and treacherous roof multiply the difficulties of mining; and increase the unavoidable waste. Even more direct is the connection between geologic processes and the, differences in the character of the coal as mined, the varying proportions of large and small sizes demanding differences in preparation and resulting in different average prices realized for the product of the mines.

Jan 8, 1923

DURING September, the Coal Commission pre- pared for issue a series of 18 reports on varied aspects of- the bituminous coal industry; the final report, dated Sept. 22, sums up the facts and offers recommendations addressed to Congress, to the industry, and to the public. The few following paragraphs are selected: Bituminous coal is the real foundation of that great industrial and transportation structure which enables more than a hundred million people to live in America and be so well supplied with things necessary for their health, comfort; and convenience; it also furnishes domestic fuel for two-thirds of the homes of the land. The distribution of the output of the bituminous mines tells the story: 28 per cent. goes to the railroads, 25 per cent. to the boiler houses of factories and mills of all kinds, 15 per cent. to the coke ovens and gas plants, 10 per cent, to the homes, 7 per cent. to steel plants and the same percentage to power plants and street railways, 4 per cent. is exported, 2 per cent is used for power at the coal mines, and the remaining 2 per cent. goes to the seaboard for steamship fuel. Bituminous coal enters into interstate commerce on a scale approached by no other commodity; less than a fourth of the coal mined in the United States fails to enter interstate com-merce. All but one of the 45 coal producing districts in the United States ship coal outside the State in which it is mined. Three hundred miles of cars loaded with coal is the daily output of the bituminous mines of the United States. The public-welfare element in coal is seen in the dependence of public health and safety on an unfailing supply of fuel, in the close connection between the prosperity of most industries and the uninterrupted operation of the coal mines, and in the obvious fact that without coal the great network of railroads which binds together this great country would be idle. The railroads and the public utilities, themselves so clearly obligated to render what-ever public service is demanded of them that the constitutionality of their public regulation is unquestioned, are of all industries most dependent upon coal. Thus, coal makes up over 35 per cent. of the operating cost at the gas plant and over 25 per cent. at the electric power station, and in the operating expenses of. a railroad the cost of coal is the largest single item, next to labor. The practical logic that half a century ago clothed with a public interest the steam locomotive and in later years the electric-power station must recognize a large element of public service in the coal mine that furnishes the necessary energy to both locomotive and power-plant.

Jan 10, 1923

By Robert Bohman

I truly free enterprise system requires free and unrestricted competition among a diversity of suppliers, in order to function properly. The natural attrition of the marketplace tends on the one hand to narrow the competitive field ... but the flow of new competitors entering the arena provides a "diluting" effect, and a "balanced" market place. Without the ready flow of new business entrants, the market becomes increasingly concentrated in the hands of fewer and. fewer firms. Competition among suppliers is diminished and the "free" marketplace suffers accordingly. A number of organizations, both governmental and private, have recently expressed grave con¬cern over the competitive future of the Western coal market. While most have noted that there is currently adequate competition within the Western market, some have cited the growing con¬centration of coal ownership ... particularly federal lease ownership ... in the hands of a relatively few firms. They suggest that unless this apparent trend is reversed or at least stemmed, the number of new firms entering the federally-dominated West may become reduced to the point where competition will suffer.

Jan 1, 1982

By D. Harrington

ANNUAL or necessary inspections and investigations of coal mines for various purposes were made possible through the Federal Coal Mine Inspection Act of May 7, 1941, which authorized entry to the Secretary of the Interior through the Bureau of Mines. Primary object of these inspections is to obtain information pertaining to health and safety conditions. Among the purposes for which the data are to be used, are annual reports to Congress, the publication of inspection reports, and the compilation and publication of statistics. The act states that inspections and investigations shall be made by employees of the Bureau of Mines, who shall co-operate with other bureaus of the U. S. Department of the Interior, as well as with the official mine-inspection, safety cr health agencies of the several states and territories. The act specifies that a coal-mine inspector shall have "the basic qualifica-

Jan 1, 1946

By John M. Lovejoy

FEDERAL regulation of the petroleum resources of the nation has long been an interesting topic for discussion. A plan to accomplish Federal control has now taken definite form. At the request of the President of the United States, a bill to be known as the Petroleum Conservation Act of 1939 has been presented to Congress-H. R. 7372, offered by Representative Wm. P. Cole, Jr., and more usually known as the Cole bill. It is an act ostensibly designed to conserve our petroleum resources, through regulation of production practices. Hearings are being held currently by a subcommittee of the Interstate and Foreign Commerce Committee, in compliance with the request of the President to report the bill early in the next session of Congress.

Jan 1, 1939

By R. D. Hutchinson

I consider it an honour to be the opening speaker in this afternoon's session on "Canadian Exploration". I also think it most appropriate that this joint meeting of the MMIJ and AIME should consider this subject, because Canada is a major exporter of mineral products and Japan and the United States are our two largest customers. Clearly, therefore, both countries have a valid interest in developments on the Canadian minerals scene. I represent the Mineral Development Sector of the Canadian Department of Energy, Mines and Resources. I will therefore speak from the point of view of the Federal Government. At this point I would like to acknowledge the help and constructive criticism I have received from several of my colleagues in Mineral Development Sector in the preparation of this paper. In any discussion of exploration in Canada, it is essential to emphasize at the outset that Canada has a federal system of government, with powers shared between Ottawa and the provinces. Under our constitution, the federal government has jurisdiction over the north, and over offshore areas, while the provinces own the natural resources within their boundaries. They control the systems of land acquisition for exploration and the terns under which mining titles are issued, and are therefore able to determine the rate and conditions of exploration and development of these resources. It follows that the Federal Government can influence the exploration and development of the provincial resources only indirectly by consultation with provincial authorities. However, once the resources are developed and begin to flow to market, the Federal Government can exert a much stronger influence because of its constitutional right to control both inter-provincial and international trade, as well as through its general fiscal and tax powers.

Jan 1, 1976

By Otto L. Schumacher

The Overthrust Belt in portions of Montana, Idaho, Utah, and Wyoming, an area that has contributed generously to the Nation's mineral supply, is one of the few remaining oil and gas frontiers on the North American continent. Determination of the oil and gas potential and development of mineral resources of the area have been affected by a variety of land withdrawals and other restrictions, The purpose of this study is to determine the extent of these withdrawals and restrictions and to discuss the mineral resource potential within the study area. Statistics in this report refer to land status on January 1, 1979. At that time, of the 27.3 million acres of Federal mineral lands within the study area, applications tor Federal oil and gas leases for more than 4,4 million acres (about 16 percent) were pending; the average length of time was 2 years. Federal oil and gas leases covering 8.8 million acres were also on record. Although drilling has occurred on some of these leases, others are subject to restrictions that discourage or prevent development. Some in fact contain stipulations disallowing any development.

Jan 1, 1981