Search Documents

By Allen L. Frank

The uranium mine environment is characterized by airborne radon-222 and its daughter products to which miners are exposed through breathing and by gamma and X rays from the uranium-235 and uranium 238 chains to which the miners are exposed externally. The nature of the radon-daughter concentrations and the methods used to define and measure the exposures are explained through an extensive review of the literature. An improved passive track-etch dosimeter for personal use is proposed which has a measurement range of about 30-400 WLH with a 95% confidence interval to ~25% for individual detector measurements in relatively stable mine air. Some measurements of these dosimeters adapted to environmental use are also presented. A program of development for enhancement of dosimeter sensitivity and greater accuracy of measurement is outlined. Extensive gamma-ray survey measurements were made in two Colorado and three New Mexico mines. Follow-up personal miner dosimetry with LiF TLDs was done at the mine with the highest exposure rates, The average miner exposure rate measured was 4.27 mR per day, or 9.3 of the maximum permissible level averaged over 13 weeks. Comparisons are made with previous mine surveys and their value in estimating miner exposure is discussed. Some depth-dose measurements made using Lucite as the absorber are evaluated.

Jan 1, 1978

By J. E. Rourke, O&apos

This report incorporates a review of available dewatering technology and an evaluation of its relevance to surface coal mines in the Interior Province of the United States. Guidelines for the selection, design and construction of dewatering systems are included. On the basis of documented experience, candidate dewatering systems were selected and evaluated with respect to their anticipated impact on the environment and mine operations. Included in the discussion is a summary of laws and regulations which can impact on dewatering operations. Following this discussion, geologic and hydrogeologic conditions within the Interior Province are described and potential dewatering problems at surface coal mines are identified. Model mines are developed which exhibit the most difficult dewatering problems identified, and it is demonstrated how available technology can be utilized to deal with these problems. Dewatering of coarse-grained, high permeability terrace deposits might be economically feasible today. Low permeability, saturated glacial tills or lake deposits appear to be significantly outside present economic feasibility for dewatering.

Jan 1, 1979

By James R. Wait

The present final report constitutes the total productivity of a series of contracts from the U.S. Bureau of Mines and the Institute for Telecommunication Sciences over the period 1971-1979. The emphasis on the research has been analytical. In this "executive summary" we give a succinct description of each phase of the investigation. In the first phase of the investigation that was stimulated by the National Academy of Engineering, we concentrated on the analytical studies of techniques relevant to mine rescue. Several specific procedures for locating a buried source were analyzed. In the next, but overlapping phase of the investigation, we dealt with the fundemental character of how electromagnetic waves propagate in mine tunnels. At the outset we allowed for the finite conductivity of the tunnel walls and the presence of axial conductors such as cables, pipes, and tracks. The third phase of the investigation was devoted to the analyses of various specific geophysical engineering problems. The related fourth phase dealt with the general subject of non-destructive testing of wire ropes such as used for mine hoists.

Jan 1, 1980

By H. S. Benson

This report documents, from concept through field testing, the pan scraper Wheel Slip Monitor. The function of this device is to instantly warn the scraper operator of wheel slip and thus enable him to take immediate corrective action. Knowledgeable pan scraper people recognize that the preponderance of scraper tire damage and wear occurs during useless wheel slip when the scraper operator attempts to increase machine draft beyond what traction will allow. The resultant shortened tire life has become very expensive. The Wheel Slip Monitor reported here provides the means for relieving the scraper operator of attempting to judge wheel slip on tires he cannot see. Direct and intuitively understandable audible and flashing light warnings tell the scraper operator which wheel is slipping and also indicate the relative magnitude of the slip. Beside the Wheel Slip Monitor's patent utility as a real time operator aid, it has unique potential for application to extended term wheel slip history acquisition under field conditions. This information has never been easily available and it promises practical value in pan scraper management.

Jan 1, 1983

By C. B. Manula

This report is mainly concerned with the modification and development of a users manual for the Open-Pit Materials Handling Simulator (OPMHS) developed at Penn State. Model Modifications included the introduction of a free-format input, the application of a Weibull random generator, facilities to stochastically simulate shovel-dragline operations, and routines to increase the flexibility in making truck assignments. At the same time, core storage requirements and execution times were minimized and all P.S.U. conventions were removed to allow operation on other computing systems.

Jan 1, 1976

Development of automatic fire protection systems for large, mobile mine haulage equipment was initiated under Department of Interior's Bureau of Mines-FMC Corp. contract H0122053, "Improved Sensors and Fire Control Systems for Mining Equipment June 1972 to May 1973." After successfully designing and mock-up testing an effective economical automatic fire protection system, and after having demonstrated that the system could extinguish controlled fires on 100-ton capacity haulage trucks, USBM-FMC contract 110232059 was issued in June, 1973, to conduct further development and validation testing. This report documents technical progress and activity under the latter contract. Figure 1 shows areas of the two haulage trucks that were protected by the automatic fire protection systems tested during this program. Figures 2 and 3 are composites showing hardware and schematic diagrams of the systems tested.

Jan 1, 1974

By V. A. Marple

At the Twin Cities "lining Research Center (TCMRC) a project is underway to determine how varying the parameters of a coal-cutting process would affect the amount and the size distribution of the generated dust. The cutting parameters being investigated are the cutting speed, depth of cut and shape of the cutting, tool. To accomplish this research ft is necessary to collect and transport the coal dust venerated at the cutting tool to measuring instruments for analysis. The purpose of this contract was to develop and deliver a system of instruments for measuring the size distributions of the generated coal dust. The instruments employed are essentially those developed for particulate air pollution measurements (1, 2). The instrument system covers a particle size range of 0.005 to 20 microns and is capable of performing in situ measurement and presenting data in real time.

Jan 1, 1974

By L. D. Gent

This report reviews the current state of the art of remote control techniques for underground continuous miners. A delineation of aspects requiring additional data is presented. Also a summary and delineation are presented in overview form for the related section functions: roof control, haulage, ventilation, power supply and rock dusting. The automated remotely controlled continuous miner project is a long-range research effort. However, the program has been divided into intermediate steps resulting in incremental production increases throughout the program. Data are developed relating the impact of our proposed research and development accomplishments to potential productivity impact.

Jan 1, 1975

By E. C. Fitch

This report discusses fire-resistant hydraulic fluid safety from three different directions. First, results of a survey prepared for the Fire Resistant Hydraulics Journal by the staff of the Fluid Power Research Center are analyzed. Second, operational limitations of fire-resistant hydraulic fluids are examined. Finally, laws and standards of various foreign countries are investigated. Three conclusions are derived from a close study of fire-resistant hydraulic fluid safety from these three directions. First, a significant number of experts in the fluid power industry are no in agreement about aspects of fire-resistant hydraulic fluid fire-resistance and toxicity. This indicates a need for more in depth research. Second, the use of fire-resistant hydraulic fluids involves a compromise between the decreased fire hazards and increased toxicity and machine incompatibility problems. Finlly, major foreign governmental agencies have thorough laws and standards concerning fire-resistant hydraulic fluids. These laws and standards may provide a solid framework for further international research into fire-resistant hydraulic fluid safety.

Jan 1, 1979

By James R. Cosby

This report describes work performed for the Bureau of Mines to evaluate available portable instruments for their effectiveness in detecting and locating damaged metallic shields in Types SHD and SHC cables. A second phase of the program is also covered wherein several instruments of a type which show promise are purchased for modification and testing to verify their performance.

Jan 1, 1980

By Richard C. Moore

The U.S. Bureau of Mines contracted a study to review the air and water monitoring requirements of five Federal environmental acts (the Federal Water Pollution Control Act, the Safe Drinking Water Act, the Clean Air Act, the Surface Mining Control and Reclamation Act, and the Resource Conservation and Recovery Act) and to compile information on the currently available monitoring instruments. A literature review of the acts and their associated regulations was conducted to determine applicability to the mining industry as well as any air and water monitoring requirements. In addition, an industry search and literature review was performed to assess the instrumentation available to comply with the monitoring regulations. Based on this research, the instruments are classified by general applicability to air, surface water, or ground water monitoring, then catalogued by monitoring parameters. A discussion is provided on recommended and innovative monitoring techniques.

Jan 1, 1981

By David A. Summers

The use of high pressure fluid cavitation is investigated as a means of breaking an ore into its constituent grains. This Cavitational Rock Dissagregation (CRD) is found to be possible and effective in breaking down galena ore, both in sandstone and dolomite host material. The technique did not work as well in comminuting and cleaning oil shale, because the cavitation drove the oil into emulsion with the water. The presence of dominant bedding in the rock also caused preferential breakage to these lines, rather than to the individual grain boundaries. This problem was also encountered in tests on igneous ore where weakness plants of the overall ore proved weaker than the boundaries of the individual grains. It was found that the prevailing expression of cavitation erosion dependence on pressure was not absolutely valid. In contrast it was found that CRD is much more sensitive to jet flow diameter, and when this was recognized it was found possible to erode rock with compressive strength of up to 350 MPa with operating jet pressures of 10 MPa.

Jan 1, 1982

By Yoginder P. Chugh

This study has appraised available deeper soil loosening equipment in the 1-4 ft. depth range, in the U.S. and abroad which has potential for Illinois prime farm-land reclamation. The appraisal was based on written and/or oral contacts with equipment manufacturers, reclamation experts, and visiting with selected equipment manufacturers. The results indicate that several manufacturers in the U.S., West Germany, and England market static and vibratory deeper soil loosening equipment which may have potential for application in Illinois. The pertinent information concerning each equipment with potential is presented in this report.

Jan 1, 1983

By James W. Reil

A test series of small, precisely-controlled and thoroughly-monitored production blasts was conducted at two quarries. In each series, all variables except delay were kept constant, as much as practically possible. The first aim of the study was to determine the effect of local geology on ground vibration. The second aim was to test several hypotheses relating the effect of millisecond delay intervals to fragmentation and ground vibration. A resonant frequency of ground vibration was shown to be related to the thickness of the overburden, in accord with a model proposed by Gupta (1961). Since the overburden geology creating this resonant vibration cannot usually be changed, two methods were tested to choose delays such that blast vibrations would destructively interfere. These were shown to be effective in modifying both the peak particle velocity and response spectra of ground vibration. The delay interval chosen also affects fragmentation, primarily in massive rock, with an optimum relief between holes of 2 ms/ft. Strain gage records indicate a possible mechanism consistent with this information.

Jan 1, 1985

By Donald Giroux

This report documents the design, fabrication, testing, and coal mine demonstration of a hopper-feeder-bolter during a four-phase program for the U.S. Bureau of Mines. The machine was designed to increase productivity and safety in under-ground room-and-pillar mining. It performed well as a hopper-feeder for continuous haulage during a coal mine demonstration. Testing in a simulated mine showed that the machine also has good roof bolting capability.

Jan 1, 1987

There has been a substantial increase in the use of rubber-tired front-end loaders in the mining industry in recent years. Concurrent with this increased usage, in the period of 1966 to 1970, there were at least 74 mining industry fatalities involving front-end loaders, or (on the average) in excess of one fatality per month. When the usage of front-end loaders by the construction industry and other industries, organizations, and agencies, such as the Government (i.e., Department of Defense), along with the uncounted numbers of serious, but non-fatal accidents, are included in the picture, the safety record for front-end loaders, of necessity, becomes a serious subject for study. There is an urgent need for attempts to be made to eliminate or reduce the number of safety hazards; to decrease the confusing diversity of controls designs found on present front-end loaders; to improve the maintenance and operating procedures; to formulate better personnel policies; to increase management and official awareness of the extent of the problem, in both industry and the Government; etc.; in order to decrease the number of accidents. Part of the problem may be traced to the fact that the operator of a front-end loader is frequently designated a "heavy equipment operator." This implies that he is automatically qualified to operate any model, of any manufacturer's, wheeled or tracked, front-end loader as well as many other types and classes of heavy equipment. Contrary to automotive practice, the complement of primary operating and emergency controls varies widely from model to model, as well as from manufacturer to manufacturer. Not only are certain controls present on one front-end loader model and absent on others, but there are significant differences in the modes of control operation, in the functions performed by superficially similar controls, in the location of the various controls, etc.

Jan 1, 1973

By T. N. Williamson

Most U.S. coal production is bituminous coal. Some 90% of current production comes from a geographical area enclosed in a circle with a 300 mile radius and its center at about Huntington, West Virginia. There are important underground coal production areas in the western parts of the United States as well. Most U.S. coal production comes from fairly level seams, many of which pitch rather uniformly only a few feet per mile. Usually there will be several overlying seams of varying thicknesses, separated by several tens of feet. Fig. 1. 1. Seams have minor local undulations but these? are small enough not to be a major consideration in a horizontal drilling research program.

Jan 1, 1970

Airy kind of a power system is a complicated network of various electrical components, such as cables, transformers, electric machines, circuit breakers, etc. For a system to work continuously and efficiently, each of the components has to be in perfect operating condition. The failure of any of these components can cause serious interruption of the supply and may in several cases involve a lot of precious time and labor in removing and replacing the damaged equipment it may also give rise to dangerous overvoltages on the system, thereby causing a safety hazard. Any piece of electrical equipment can have two likely modes of failure. The first would be the degradation of solid insulation material due to overheating, mechanical damage or a combination of the two, In this mode of failure it is possible that If the insulation damage is not an instantaneous phenomenon (a cable damaged by severe mechanical, Stress) that a detectable leakage current will do lop prior to the faint. The fault would probably he a result of heating and deterioration of the insulation by the leakage current.

Jan 1, 1975

By Ralph B. Stevens

The objective of the Automatic Fire Sensing and Suppression Systems for Mobile Mining Equipment program is to document the design, fabrication, factory testing, 11-month in-mine testing, and final demonstrations of auto¬matic fire protection systems on several units of mobile mining equipment including trucks, front-end loaders, cranes, draglines, coal haulers, and cutters. Proper sealing of all system components from the elements, especially in corrosive mine conditions, is essential for reasonable life-cycles with minimum maintenance. Also, adequate power supplies, wire, connectors, and plumbing with adequate protection from the harsh mine environments and physical damage were necessary during the in-mine tests. The fire protection systems were developed from technology employed during two previous Bureau of Mines contracts: HO122053, Improved Sensors and Fire Sensing Systems for Mining Equipment, and H0232059, Validation Testing of Truck Fire Protection Systems.

Jan 1, 1978

By Charles E. Green

This study was conducted to identify, evaluate, and develop procedures to minimize or eliminate safety hazards associated with the electrokinetic dewatering process, such as toxic and volatile gas emissions, electrical shock, accidental detonation of explosives, electrochemical corrosion of metal appurtenances, and possibly others. The identification, evaluation, and procedure development were based on pertinent literature, existing safety regulations, interviews with mine personnel, physical and mechanical properties of the electrokinetic dewatering process, and physical characteristics of the material to be dewatered. The electrokinetic dewatering process was described in detail. Potential safety hazards were identified and evaluated. Procedures and/or safety regulations were developed to minimize or eliminate the potential hazards. It was recommended that the electrokinetic dewatering process when used in deep metal mines be properly monitored to obtain additional information on other potential hazards that possibly exist.

Jan 1, 1979