Search Documents

By Mauricio Brücher, Juan Camus

This article deals with open pit mine planning and a computer technology known as Direct Block Scheduling, or “DBS”. This is an emerging technology for modeling mine exploitation strategies using mixed-integer linear programming. This technique has proved to yield stronger economic results compared to the Lerchs-Grossmann (“LG”) algorithm currently used at the beginning of the mine planning process. The article briefly describes the shortcomings of current practice; then, this delves into the superior results obtained by DBS technology compared to current practice. Finally, the article argues that results achieve so far by DBS could be enhanced even further. To do this, the framework to apply this emerging technology, which is also used in current practice, should be modified to better exploit the capabilities of DBS technology. To better understand this change, an illustrated case study is presented at the end of the article.

Jun 25, 2023

By Julianne H. Glarmaty, Peter J. Conroy

INTRODUCTION In 1970 the percentage of underground coal extraction by longwall mining methods in the U.S. was 2.1 percent. This figure rose to 4.4 percent in 1976 and is expected to rise to 12 percent by the year 1985. This figure represents 46.0 million tons (51.0 million st) of annual production (Kuti, 1978). In addition, OSM regulations are placing emphasis on subsidence prediction. Section 784.20 of the Office of Surface Mining regulations for underground mining permit applications requires the sutauission of a subsidence control plan which may include monitoring. Because of its nature, longwall mining does not have flexibility in leaving pillars under structures as does room and pillar. Mining in some areas, particularly in the Eastern Coal Field, is approaching more developed areas; therefore, a greater number of structures are expected to be undermined in the near future. Subsidence engineering is becoming an important aspect of mine planning, and should be directed at predicting potential structural damage. The question operators are increasingly faced with is "what will be the subsidence effects for a specific structure at a specific location in respect to a longwall panel?" The most significant variable in assessing the subsidence effect on structures is not vertical subsidence. The variables of strain and tilt are responsible for more structural damage than is the vertical movement. Table I presents threshold values of strain for various structures (Geddes 6 Cooper, 1962). Based on National Coal Board experience, horizontal strain is approximately inversely proportional to the radius of curvature of a circular portion of a subsidence profile; therefore, the radius may be useful in estimating the magnitude of strain caused by subsidence (Hoebs, 1982). The radius of curvature can be determined by the following equation:

Jan 1, 1982

By Stefano Ceccotto, Eugenio Trussoni

"INTRODUCTION Contemporary city is made of layers. Physical structures layers (built fabric, residential, commercial industrial etc. ), infrastructural layers (below and above ground), “green” layers (parks and open spaces), and also informational layers, i.e. connections, links, between sectors of the city and other territories. The “city of layers” concept represents the exercise of “rebuilding the city” per each layer, highlighting those physical built structures that are functional to define a relation. For example, if consider the “connection” relation, the city is re-designed by considering only transportation built structures. The layer obtained in such fashion is hence the “transportation” layer, including below grade infrastructures (subways) and above grade lines (rail, bus, tramways etc.), as below shown in Figure 1.In this sense, the contemporary city is represented by separate constructs assembled together according to a specific functionality (e.g. “connection”). As a consequence, the relation between what is built underground, and the related above-ground development, can be perceived in his most evident appearance. What could happen within the contemporary city if the planning process would begin from below to above and not vice-versa?INTERACTION The question risen in the introduction is strategic when approaching the difficult task of designing (or re-designing) a multi-level organism like the contemporary city. Nowadays, the theme of integration between underground and at-grade master planning has become the subject of many urban renovation projects, where the design process has begun within the transportation layer, underground, and further developed by interacting with at-grade structures already existing or in phase of design.A series of case studies where below/above interaction plays a key role in the project will be further analyzed. Moreover, it is relevant to understand the mechanics of an urban transformation process that originates within the transportation layer and ends up with the design of entire sectors of the city. The Transit Oriented Development approach is a useful tool to clearly understand such transformation process. TOD has become, in particular in the last decade, one of the most effective tools for urban design, in order to solve simultaneously the many different instances related to transit planning, urban design and real estate market."

Jan 1, 2016

By D. P. McDonald

"IntroductionTHE PURPOSE of this paper is to present .a summary of the evidence given before the Petroleum and Natural Gas Conservation Board in support of applications to it for permits to export natural gas from Alberta.I will attempt to be objective in my statements, despite the fact that my main interest in the hearings before the Board was to advance the interests of my own clients, the Westcoast Transmission Company, Limited.The hearing of the export applications •commenced before the Board in January, 1950, with the .application of the Westcoast Transmission Company. Joint hearings were commenced in September, 1950, and completed on December 14th, 1951. The Board heard evidence in support of six applications for export, one application to build a gathering system in Alberta, and three interveners, the .latter being the City of Calgary, the local gas companies, .and the coal interests, including both operators of coal mines and the Unions.The evidence comprised better than 8,400 pages, over two million words, and occupied 92 days before the Board.The Interest in Natural GasThe natural gas industry is one of the newer industries. It is not yet twenty years •old. In the United States, the expansion •of pipeline facilities has been phenomenal in the last fifteen years, and particularly in the last three years, when a total of over two billion dollars was invested in pipeline facilities. There are approximately 250,000 miles of gas transmission pipelines in the United States at this time, with additional lines constantly being pressed."

Jan 1, 1952

By E. J. KENNEDY

FEBRUARY 15-18 will be the outstanding dates of the month for members of the A. I. M. E., for then the 141st Meeting of the Institute is to be held in the Engineering Societies Building, at New York. What with 41 technical sessions, the Annual Business Meeting at 4 o'clock Tuesday afternoon,, two sessions of the Section and Division delegates, minor committee meetings, and the many luncheons and dinners, the Dinner-Smoker, Informal Dance, President's Reception and the Dinner-Dance, the opportunity will be limited to do- more-than cast sheep's eyes at New York's other multitudinous attrac¬tions until the meeting is over. The technical program is diverse but well organized. The sessions are almost equally divided among the four days, with ten on Monday, Tuesday, and Wednesday, and 11 on Thursday. The meeting opens Monday morning with registration. Be sure to attend to this detail. Failure to do so may have its repercussions at the meeting and throughout the year.

Jan 1, 1932

By William H. White

"AbstractThe value of anomalous metal contents of trees as an aid to the discovery of mineral deposits was tested under field conditions cm four known ore deposits. Results indicate that a base-metal deposit, or any deposit containing zinc or copper, casts a 'metal shadow' into the overlying soil which remains approximately positioned above the deposit, regardless of the type of overburden or the movement of groundwater.The unusually high content of zinc or copper in trees growing within the limits of this 'metal shadow' constitutes an anomaly which can be detected and ,plotted in the field The field kit and certain points of the field technique are described briefly; and the characteristics of plant anomalies and possible limitations of their use are mentioned.IntroductionRecent investigations concerning the metal content of trees indicate not only wide variations in the metal content of different species and in different parts of the same tree but, in addition, suggest that the metal content of a tree is related to that of the subjacent bed-rock. Abnormal values found by Warren, Delavault, and others in trees growing above or near orebodies suggest a new tool which may prove of considerable value in exploration work. Evaluation of this new tool must involve consideration of the following questions:(I) Is the technique one which can be used under field conditions by persons not specially trained; and can results be duplicated within reasonable limits of error? Rather than taking tree samples for subsequent laboratory analysis, it is highly desirable that analyses be made on the spot. This allows anomalous results to be checked and additional samples may be taken at key points."

Jan 1, 1950

By G. Bourque

Early in the design stage of their new concentrator for the Mount Wright Plant, Quebec Cartier Mining decided to use a process computer for total control of crushing, grinding and concentrating. A map of the area is given in figure 1 and a view of the plant in figure 2. Although the use of process computers is not a new idea in petrochemical and chemical industries, their use in the mining industry is very limited. We innovated in using the computer, not only for data logging, as we have seen in some other plants, but a sole operator located in the administration building, starts and stops mill lines, crushers, load-out system, tailings, thickeners, etc ... by means of a CRT console. Our process is fairly simple as can be seen on the schematic process flow diagram (figure 3). .The ore, carried by 136t diesel electric trucks, is dumped through ore pockets onto two primary pan feeders. The feeders supply two 1,52mx2,79m gyratory crushers which reduce the ore to minus 20,32 cm. Each crushing line have a capacity of 5600t per hour and feed a shuttle conveyor distributing the crude ore into six silos.

Jan 1, 1979

By D P. Murphy, R F. Dewhirst

Traditionally closure has been seen by the Resource sector solely as a green or an environmental issue, focused primarily on the requirement to rehabilitate the site following cessation of production activities. In addition to operational, maintenance and production aspects of processing plant design, future design teams will need to take a more holistic view and consider an increasing number of sustainability issues including safety in design and cleaner production as well as closure itself. Sustainability principles being adopted by industry such as the Minerals Council of AustraliaÆs Enduring Value Framework are now broadening our understanding of closure. While issues around the closure of tailings dams and associated infrastructure have been widely studied, few investigations have looked closely at the implications of closure on the design of minerals processing plants. It is likely that design teams may be able to make a significant contribution to meeting industry objectives by adopting innovative designs which, in addition to meeting production objectives, deliver sustainable and cost effective plant closure outcomes. This presentation explores the opportunity for innovative design of mineral processing plants through the assessment of alternative closure objectives. This assessment specifically looks at current industry standards and statutory requirements, as well as potential risks and opportunities associated with each objective. Alternative design strategies to meet these objectives are discussed.

Jan 1, 2006

The complete life cycle of a production facility has many phases requiring many different skills and many different personalities. It is not unlike the life cycle of a person and many parallels can be drawn from it. I leave some of these analogous situations to your fertile minds. The author, having worked in operations, plant design, plant commissioning, marketing and many other interesting situations through the industry has drawn from this experience and examples given by many associates in the industry.The phases seen are as follows: Concept Studies û someone has a bright idea of how to make a dollar. Scope Studies û what possible processes/options that could make a dollar. Prefeasibility Study û the æviableÆ scope options are studied to develop feasible options. Feasibility study û defines the concepts that should be designed to make a viable project thus enabling financing and project commitment to be made. Detailed Design û an intermediate step that consolidates the inputs to give a robust plant that can be constructed.Construction û people can see what they thought was going to occur and start to understand the plant. Commissioning û the hand-over of æownershipÆ from the conceiverÆs to the operators. Operations û the ætoyÆ has become reality and money must be made. De-commissioning û the plant has seen out the useful life of the ore deposit, it now goes through a further process required by society.Across these phases of plant design run several countervailing management requirements that can influence the outcome of the plant design. Some of the management rigours that have to be applied to the various phases are as follows: costing basis of the various phases; operational and maintenance reviews; sustainable development; risk assessment; reliability reviews; equipment availability; commissioning time; and environmental review.This paper endeavours to awaken people to the phases that projects require for a successful outcome and the management rigour that has to be applied throughout the phases to ensure the correct intellectual horsepower is applied at the right time to ensure the best outcome.Many of you would be parents and realise this is not unlike the development of children, teenagers, adults, retirees and ongoing.

Jan 1, 2002

By William R. Yernberg

The Mineral Processing Plant Design, Practice and Control Conference was held from Oct. 20through 24, 2002, at the Fairmont Hotel, Vancouver, British Columbia, Canada. The conference was attended by nearly 400 of the world’s top mineral-processing specialists, including plant-design engineers, mineral-processing consultants, academics, suppliers and equipment manufacturers. The meeting was sponsored by SME and cosponsored by the Canadian Mineral Processing Division of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM). The conference covered all aspects of mineral-processing design, construction and operation. The meeting included more than 130 technical presentations. Topics included sampling programs, feasibility studies, design criteria, process technologies, construction, start-up operations and shutdowns. To stimulate interaction and discussion throughout the five-day conference, the sessions were presented consecutively. Attendees had the opportunity to attend every session.

Jan 1, 2003

By J. C. Monette

Stripping of gold and silver from carbon is effected by means of two main processes (AARL and ZADRA ). The main rate-enhancing parameter in the stripping of gold and silver is temperature. A secondary rate-enhancing parameter is ionic strength. (1) Stripping is usually conducted within a solution containing sodium cyanide (0.1 -0.5% ) and caustic ( 1 -3%). The development of a chemistry that increases the rate of gold and silver stripping from carbon in a manner proportional to its concentration is described. Its use in atmospheric and pressure strips is also outlined.

Jan 1, 1992

By Larry S. Diaz

The paper considers the selection of control instrumentation for a modern flotation plant, as well as the best interpretation and most effective use of the process data obtained. Process control computer availability is considered from the outset. A general philosophy of control is proposed which leads toward a system that is its own reliability monitor. The bulk of the problems are in grinding and classification. Alternative control methods are described that use particle size measuring devices. Flotation controls, based to a large extent upon on-stream X-ray analysis, are reviewed in detail. Reagent control methods are also examined. Methods to analyze the data obtained from the various measurement devices are introduced. These methods would enable an estimate of the validity of the data and require some redundant information. Another objective of these methods is the protection of operating equipment from possible control malfunctions. Although the discussion generally considers some degree of computer usage, this paper attempts to describe instrumentation and data analysis methods that enable control with or without the process control computer.

Jan 1, 1972

By Jeffrey T. McGinty, Frank M. Wheeler

Plant layout is the arrangement of equipment, process areas, departments, infrastructure, and support facilities. Plant logistics is the flow of parts, people, resources, and information throughout the production process. This chapter: outlines key factors and provides checklists to facilitate layout development; presents risk management approaches to test the logistics and functionality of alternative layouts; and uses real-world examples to illustrate effective simulation modelling to assess plant layouts.

Jan 1, 2015

By J. A. MacLellan

It is the hope of the author that this paper, largely a compilation of observations and opinions built up over 20 years of experience in cold and remote areas may be of some help to others in designing better plants for the future in the north. The north is not as difficult to operate in as the better story tellers make it appear to be. ()n the other hand for 6 months of the year the cold is always there, and it seems to be waiting for someone to make a mistake. The simplest things can shut a multi-million dollar plant down at -4n' F with a 4n M.P.H, wind. It only takes one man door improperly latched to freeze up all the pumps on the bottom floor. Someone can poke a one inch hole in an outside wall in July and six months later while you are having Christmas dinner, a watchman will call up to report that the whole plant is flooded because the main water line just froze up and burst. Basic things to remember in plant design for cold and remote areas are: everything in these areas is more expensive due to long and difficult supply lines. Fuel is expensive and would be a major cost item even if it were not expensive, due to the extended periods of low temperatures. Building volumes should therefore he kept to an acceptable minimum. Service areas on the other hand must he adequate, because maintenance generally has to be conducted inside in a heated area. Supply vehicles for instance have to get completely inside the building to unload. If you try to unload a supply vehicle with the door open at -50° F, you won't be able to find the vehicle for fog and if you take more than 5 minutes half the water lines in the plant will freeze up. People in a remote area are expensive. The capital investment per employee may be as high as $30,000; with fringe benefits per annum costs of an employee will he as high as 812,000 per year regardless of basic wage rate. It

Jan 1, 1971

By J Li, H Hooi, D Payne

Caval Ridge Mine (CVM) is one of the newly established open-cut coal mines of BHP in Queensland, where no tailings dam is planned to be built in order to minimise environmental impacts from mining activities. The waste streams from the Coal Handling and Processing Plant, including fine tailings dewatered by belt filter presses, coarse rejects, and mixed plant rejects, are co-disposed within waste dumps built with pre-strip and dragline spoils. Due to high rejects output (35 – 60% of feed) and low spoil to reject ratio (< 5) the large quantities of rejects bring significant geotechnical and operational challenges to CVM, which are exacerbated by increasing annual production rates and additional rejects from washing coal from an adjacent mine. Further in-house geotechnical review commenced in mid-2014 based on the initial geotechnical studies during the project stage of CVM between 2011 and 2013. The outcomes have enabled rejects disposal at CVM by constructing large belt filtered tailings cells, coarse rejects only dumps, and co-disposal of the mixed plant rejects at dump tip-heads. This paper presents the rejects disposal strategies at CVM from both technical and operational aspects. It also discusses future projects for belt filtered tailings moisture reduction including assessment of tailings clay mineralogy, as well as mixed plant reject co-disposal verification and optimisation.CITATION:Li, J, Payne, D and Hooi, H, 2018. Plant rejects disposal strategies applied at Caval Ridge open cut coal mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 50–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By T. P. Johnson, A. Vathavooran

"Conventional mining operations can produce a wide range of wastes containing gold and other precious metals but which are less suitable for processing by traditional methods. There are also types of ore that do not fit easily into a traditional processing flowsheet, e.g. because the refractory nature of their minerology or the combination of valuable metals is less suitable for traditional processes. Nevertheless, these potential sources of valuable metals remain unexploited resources that have attracted growing interest in the metals and mining industries over recent years. The challenge is therefore to develop and use alternative processing methods that have the flexibility of operation to cope with a wide variety of material types and tonnages, whilst providing high recoveries for valuable metals. Tetronics’ DC plasma smelting technology achieves industry-leading recovery rates for precious metals from a wide range of input materials and initial precious metal concentrations, whilst generating an inert slag-based material as a by-product (even when starting from a hazardous waste input material), approved within the EU for use in construction applications. This paper describes how this technology can be used as a key part of an overall process for the recovery of precious metals from these interesting materials.INTRODUCTION The extraction of gold from its ores by various forms of cyanide leaching has been practised by the mining industry for over a century (Minerals Council of Australia, 2005) and it remains the primary extraction method in a wide range of mining operations. The ability of cyanide to extract gold efficiently and quickly from lower grade ores without extensive additional processing, coupled with well-known methods to recycle the cyanide for re-use within the process mean it is often both the most economically preferable and environmentally acceptable method for recovering gold. As a result, 88% of all gold produced from mines in the USA in 2014 was recovered via leaching of open heaps or dumps (UGGS, 2016). Nevertheless, there are occasions where certain combinations of mineralogy and other circumstances reduce the effectiveness of cyanidation techniques, so that ever more elaborate additional processing steps are required, with inevitable increases in operating costs (Swash, 1988). In these circumstances, which are likely to be more common in future as ore qualities diminish, other methods of extraction may offer better alternatives. Whilst much less commonly used for Au extraction at present, pyrometallurgical methods are amongst the longest-established of these alternative approaches and merit serious consideration in such cases."

Jan 1, 2017

By B. S. Xakalashe, I. J. Geldenhuys, B. Bowman, M. W. Erwee, G. A. Venter, J. Zietsman, C. Sandrock, Q. G. Reynolds

Understanding the behaviour of plasma arcs is an important part of the design and operation of direct current electric arc furnace smelting processes, which are used in the industrial production of many metallurgical commodities. In recent years numerical and computational modelling techniques have begun to illuminate the complexity of arc behaviour and how it is deeply connected to the thermodynamic and physical properties of the arc plasma. Plasma properties may be estimated from first principles using statistical mechanics methods, but this requires as input some knowledge of the composition of the gas phase that occurs over the process during smelting. In this paper the authors describe a workflow using thermochemistry software to predict the expected gas phase composition through a given process, followed by plasma property calculations using an open-source software tool that has been in development for several years. This tool, 'minplascalc' has been in development for several years and is also described in detail here. The workflow is then applied to the calculation of plasma properties of interest for a variety of historical and current pyrometallurgical processes, and the results are compared. The plasma property data are published in an open-access database for general use.

Mar 4, 2025

By Jerome Feinman, Sven O. Santen

"The principles involved in the generation and application of plasma energy are reviewed briefly and the major developments in commercial and semi-commercial primary metal and alloy production are described and discussed in broad outline, with emphasis on present performance and future potential. New concepts in the application of plasma energy in primary operations are described with emphasis on the expected advantages over conventional technology and the problems that have to be solved to enable effective implementation.IntroductionThe use of plasma energy in industrial processes is generally considered to have started in 1905 with the operation of the Birkeland process for nitrogen fixation for fertilizer production. Although it seems logical to apply plasma energy to metallurgical processes, which also usually require considerable energy at high temperature levels, serious development work along these lines did not begin until the early 1970's. The reasons for this hiatus are associated in part with recognized difficulties in applying plasma energy in processes involving tonnage quantities of solids in severe industrial environments and the delicate nature of the earlier plasma generators. Another, and perhaps overriding factor, is the fairly steady improvement in efficiency and economy of most primary metal producing processes by conventional developments and modifications through the 1950's and 60's. Examples of these evolutionary changes include burden preparation and fuel injection in blast furnace applications and prereduction treatments in ferroalloy operations. By the end of the 1970's most primary metal producing processes had been optimized close to the limit, at least in terms of those operations that were able and willing to implement the developed improvements. In this context, plasma energy offered the possibility to achieve further significant improvements in primary operations where conventional means were exhausted."

Jan 1, 1988

By R. E. Brewer

A critical review of the numerous test methods that have been devised for measuring the "plastic" and "swelling" properties of bituminous coking coals and the practical evaluation of the data obtained has long been needed. The author appreciates fully, first, the arduous problem of doing justice to the merits and limitations of the many original test methods and their manifold modifications and, second, the more difficult task of interpreting the test data obtained in their practical applications to the important problems involved in the coking process. It has been the constant aim of the author to point out the broader significance of the test principles employed in the different classes of test methods and the usefulness of the test data obtained in relation to the problem of coking bituminous coals, rather than to stimulate unduly a controversial criticism of the merits and limitations of any particular class of test methods or of individual test methods devised by different workers. The task has been quite difficult because of the almost total lack of accepted test standards and specifications.

Jan 1, 1942

By M. R. Pickus, C. H. Mathewson

THE study of the plastic deformation and recrystallization of metals has been the subject of many investigations. In regard to the simple deformational processes, such as tension and compression, the early knowledge gained from studies of polycrystalline material has been supplemented by many significant researches on the behavior of single crystals. Unfortunately, this has not been true for more complicated deformational processes. As far back as 1927, G. I. Taylor1 wrote: It is impossible in the present state of knowledge to do more than give a possible reason why (face-centcred cubic) crystals set themselves with a (110) direction in the plane of rolling, and at right angles to the direction of rolling. The explanation of why the orientation of the crystal axes round the transverse direction is what it is, must be left till the distortion of metals, and particularly single crystals of metals in the process of rolling, has been studied in greater detail. That this gap in the systematic study of deformation and recrystallization has not yet been filled was indicated by C. H. Samans,2 who wrote in 1934 that "only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature." Of these four studies, only those of S. Tanaka3 and T. Sakao,4 both of whom worked with aluminum crystals, had quantitative significance. The other two, carried out by F. Wever5 and W. G. Burgers," were of a qualitative nature. It is our hope that the present investigation may contribute something to the knowledge necessary for a rationalization of the origin of rolling textures in terms of the known behavior of single crystals, and may add pertinent information concerning the recrystallization characteristics of deformed single crystals.

Jan 1, 1938