Search Documents

By J. Visman

"SummaryThis paper is presented as part of a programme to show the steps taken by industry and others interested in supplying a solid fuel of constant quality to 'satisfy a consuming market. The paper deals with the general principles underlying quality control in coal preparation plants, namely, constant quality and close adherance to acceptance limits. It also describes how control of ash content is ""generally hampered by the problem of coal sampling .and the long duration of the ash analysis and how these difficulties may be overcome.Quality control can be effected in several ways. Thorough blending wll reduce variations appreciably, except those of long trend. The latter can be detected by automatic sampling and quick ash analysis. At present, under favourable conditions, a system of half-hourly ash determinations with an accuracy of 0.5 to 1.0 per cent can be realized, to the effect that trends with a 'wave length' of more than two hours cu be eliminated within the limits of accuracy of the ash figures. The general solution of the problem is a combination of blending, accurate sampling, quick ash determination, and statistical analysis of the pattern of ash distribution.The use of statistical methods of analysis, such as the t test and F test, is •discussed at some length in order to emphasize the importance of the correct evaluation of observational data if there is to be confidence in the validity of test results.General ConsiderationsCOAL, as a fuel, is too cheap for a long haul across the country. The limiting distance depends on the price of the local competitive fuels, and, as the price depends to a great extent on quality, so does quality, to the same extent, command the market."

Jan 1, 1952

By Silvana Costa

The quality of life in remote mining communities is a significant factor that impacts the mining industry?s ability to attract and retain high quality workers in remote areas. The rapid growth of mining development, along with the shortage of skills and training globally are reflected in an increasing need to identify the ideal conditions for employee wellbeing and investigate ways to improve quality of life of miners and their families in remote locations.

May 1, 2007

By P. K. Hofmeyr

Traditional fire assay dates back over 3000 years and has changed very little over that time. The only improvement is to replace the gravimetric finish with dissolution of the Precious Metal bead followed by AA or ICP analysis of the solution. The newly developed FIP A (Fast In-line Fire Assay) method allows full automation of the fire assay process from sample preparation to spark analysis of the Pb button. This results in fully quantitative analyses for Pt, Pd, Rh, Ru, lr, Au and Ag in typically less than an hour after a sample is entered into the system. Detection limits are theoretically Pt 0.08 ppm, Pd 0.002 ppm, Rh 0.002 ppm, Au 0.08 ppm and Ag 0.002 ppm but in practice the lower measurable limits are about double these figures. Few opportunities have been available to present data obtained using the FIFA system as all FIFA laboratories have been in the domain of a Pt mining company which prefers to keep all Pt analytical matters confidential. However, IMP has recently participated in the round robin exercise to establish recommended values for a new series of Merensky Reef and UO-2 Layer reference materials produced by African Mineral Standards. The precision of the results was excellent being on average Pt 2.05%, Pd 1.25%, Rh 4.08% and Ru 4.94% being expressed as Relative Standard Deviation. The excellent precision is a reflection of the efficient collection of POEs in the Pb buttons and the homogeneity of the Pb buttons. However, the accuracy was not as good. The poorer accuracy is interpreted as the calibration of the spectrometer not being as good as desired due to the difficulty in acquiring a suitable range of standards with reliable recommended values for the PGEs. The most recent spectrometer was calibrated with the greatest care and produced slightly better results for Pt, Pd and Rh and slightly worse for Ru.

Jan 1, 2014

By O Dominguez

Mine value chain reconciliation (MVC) is a necessary procedure to evaluate a mine’s performance against the assumptions and models used to plan mining and processing operations. Using nomenclature from Parker (2012), F2 reconciliation is the ratio between material received at the mill, compared with material sent to the mill, commonly reported in terms of tonnes, grade and metal. Measurements of material sent to the mill can be estimated in many ways, including: fleet management system (FMS) records, truck counts, or volume reduction. Most time-based reconciliations (for example, month-end reconciliation) use short-term model depletions of in situ rock measured by periodic topographic scans or surveys.

Mar 22, 2022

By R. L. Garrett

The quality of mineral additives used 1n a drilling fluid (mud) can dramatically affect the fluid's properties and the overall cost of drilling an oil or gas well. The principally used minerals are bentonite, barite, barite/hematite blends and hematite alone. The high specific gravity minerals, barite and hematite, are used to increase drilling fluid density. Bentonite clay is used to increase drilling fluid viscosity, gel strength and to provide a low permeability filter cake. A multi-million dollar investment in a well and the safety of the personnel on the drilling rig can depend on how effectively these mud additives perform with other constituents in the mud. This paper points out effects caused by small amounts of certain carbonate and sulfide mineral impurities in barite or hematite and how polymeric extender additives in bentonites contribute to unpredictable behavior of a mud. Effects like these are the reason why oil companies who use these materials sometimes set their own quality standards beyond those already specified in API Spec. 13A. Also discussed in this paper are the current standardization activities in API Committee 13 on these minerals.

Jan 1, 1986

By H Lieberwirth, M Pfeifer, F Heinicke

HPGRs (high pressure grinding rolls) have been developed within the last decades for energy efficient processing of a wide variety of ores. Special interest has been raised by projects increasing the capacities of processing plants by installing HPGRs prior to ball mills. Bond ball mill tests have been used for decades as a base for ball mill dimensioning in mineral circuits. For final CAPEXOPEX considerations of the processing circuit, one key question is about the level of grinding energy split between HPGR and downstream grinding stages. This is especially interesting if the downstream process comprises multiple grinding stages combined with separation steps. The paper presents investigations on grinding energy consumption, size distribution and microfracturing of HPGR products, which affect the efficiency of the whole comminution and sorting process.

Aug 24, 2022

By Angus Maxwell, Jacob Grasmick

As the tunneling industry continues to adopt Tunnel 4.0, digital twins of the tunnel construction site are becoming standard requirements for tunneling projects. However, the benefits of these remain unproven to many practitioners. The paper discusses the various implementations of digitalization and describes efforts to combine all data types to analyze the relationships between influences, predictions and performance in a single digital platform. This includes data pertaining to investigations, design, construction, monitoring and post-construction asset performance and management. Based on 16 years of global tunneling projects the paper aims to quantify the tangible and intangible benefits of such systems. Using a number of real examples, the paper describes where opportunities were taken and where they went unrealized. Challenges and considerations for both procuring and developing these digital twins are also discussed.

Jun 13, 2021

By J. Noll, E. Cauda, T. Barone, S. Vanderslice

Measuring diesel particulate matter (DPM) for underground metal/nonmetal mine compliance samples is done by collecting DPM onto quartz fiber filters and analyzing the samples via NIOSH method 5040 for elemental carbon (EC) and total carbon (TC). As part of the sampling train, two quartz fiber filters in tandem are housed inside an SKC DPM cassette that includes an impactor. The impactor segregates DPM and mine dust, and the second filter is used to correct for adsorption of vapor phase organic carbon (OC). Since the value of the second filter is subtracted from the first, the pre-existing carbon on the filter media for both filters needs to be comparable. In addition, the pre-existing carbon on the media should be low for accurate and sensitive results. However, there have been some reports of elevated OC on the filter media of the SKC DPM cassettes, which would cause the limit of detection (LOD) to be higher than reported at times. In this study, blank SKC DPM cassettes from different batches and with different expiration dates were analyzed to quantify the amount of carbon on the filter media and to determine the LOD and limit of quantification (LOQ) associated with these samplers. It was found that the organic carbon and total carbon on the media was about five times higher than quartz media used in samplers from other studies. The average TC on the blanks was 2.57 μg/cm2 with a standard deviation of 0.70, resulting in a LOD of 21 μg/m3 TC, 8-hr Time Weighted Average (TWA), and LOQ of 69 μg/m3 TC, 8-hr TWA, when using these samplers for collecting DPM. The LOD and LOQ may be improved through some sample preparation techniques. INTRODUCTION Exposure to diesel exhaust (DE) is associated with an increased risk for lung cancer and other adverse health effects (Attfield et al. 2012, Silverman et al. 2012, Ping and Guang 2017, IARC 2012). Pronk et al. 2009 reported that the highest exposed groups to elemental carbon (EC) from DE worked in underground sites in mining and construction and they were exposed to concentrations between 27–658 μg/m3. At concentrations (1–25 μg/m3 EC) well below those observed in mining, diesel particulate matter (DPM) exposures were estimated to increase the risk of cancer by levels exceeding those typically acceptable for occupational risk in the United States and Europe (Vermeulen et al. 2014). This suggests that underground miners are especially at risk because of their more substantial exposures in confined working spaces. As a protective measure, in 2001, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/nonmetal underground miners to DPM to an 8-hr time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, 2006).

Jan 1, 2019

It is predicted that vast volumes of affected mine water will be produced by mining activities in the Mpumalanga coalfields of South Africa. The potential environmental impact of this excess water is of great concern in a water-scarce country like South Africa. Research over a period of more than 10 years has shown that this water can be used successfully for the irrigation of a range of crops (Annandale et al., 2002)1. There is, however, continuing concern from the local regulators regarding the long-term impact that large-scale mine water irrigation may have on groundwater quality and quantity. Detailed research has been undertaken over the last three years to supplement the groundwater monitoring programme at five different pilot sites, on both virgin soils (greenfields) and in coalmining spoils. These sites range from sandy soils to very clayey soils. The research has included soil moisture measurements, collection of in situ soil moisture over time, long-term laboratory studies of the leaching and attenuation properties of different soils and the impact of irrigation on acid rock drainage processes, and in depth determination of the hydraulic properties of the subsurface at each of these sites, including falling head tests, pumping tests and point dilution tests. This has been supported by geochemical modelling of these processes to quantify the impacts. The results indicate that many of the soils have considerable attenuation capacities and that in the period of irrigation, a large proportion of the salts have been contained in the upper portions of the unsaturated zones below each irrigation pivot. The volumes and quality of water leaching through to the aquifers have been quantified at each site. From this mixing ratios have been calculated in order to determine the effect of the irrigation water on the underlying aquifers. Keywords: coalmines, irrigation, gypsiferous mine water.

Jan 1, 2009

By D. Farrow

Future development of kimberlite mines is now focused on mining at deeper levels. The consequences are increased difficulty and costs of the mining operations. The decisions on investments require accurate resource evaluation and quantification of the risk. In the decision process the first step consists in choosing the number of boreholes sampling the pipe relative to the level of uncertainty that can be accepted. The uncertainty in the volumes of rocks of different types can be assessed as soon as we can estimate these volumes from a given borehole layout and calculate the error by means of its variance for instance. In theory this can be achieved by using geostatistical techniques (‘transitive theory’), but in practice the calculation of the error on volumes can be achieved in very particular cases, assuming some regular sampling patterns. A different approach has been chosen based on simulations, giving maximum flexibility to reproduce the reality of the sampling procedure. The idea is to simulate the geometry of several ‘possible’ pipes with their internal geology and estimate them by kriging. Several experimental errors are obtained on which risk analysis can be performed. The aim is to find a feasible method to perform the simulations with reasonable chance to correctly represent the reality, without data on the pipe extension. The methodology applied is based on some hypotheses that can be assessed by the geologist as well as by the geostatistician. The procedure assumes a geological model based on current knowledge including appropriate geostatistical variation. What make these simulations specific and powerful in this case comes from the fact that the boundaries between the different rock-types can be simulated using a transformation of the real 3D space into a 2D space defined by means of polar coordinates. Ultimate transformations to account for smoother variations with morphological transformations allow the generation of realistic pipe geometries on which sampling pattern can be used to evaluate the estimation errors. By estimating the simulated pipe geometries with different boreholes layouts a risk curve expressing the uncertainty in the volumes of the different rock-types versus the number of holes can be developed.

Jan 1, 2003

By Mark F. Sindelar, Yi Luo, Hua Jiang, Michael T. Shook

"Convergence of roof and floor in underground mine openings is a common occurrence. This convergence not only adversely affects the ability of workers, equipment and supplies to travel through the mine, it also reduces the effectiveness of the mine ventilation system, which is essential for the dilution of methane gas and airborne respirable dust. While installing secondary standing supports to control floor and roof convergence, such supports, by nature, partially obstruct a portion of the airway. These added obstructions inhibit the ability of the ventilation system to operate as efficiently as it could by increasing the resistance in and reducing the cross-sectional area of the airway.This study introduces and demonstrates the benefits of The Eye CAN™ standing roof support, which controls floor and roof convergence and is less obstructive to air flow than conventional wooden cribs. Laboratory findings show that the normal resistance of a supported lined airway is reduced by using this new product from Burrell Mining Products, Inc., while providing the same roof support characteristics of an established product-The CAN®. Load vs. displacement curves generated from laboratory tests demonstrated that this new product behaves with the same roof support characteristics as others in The CAN product family. Ventilation data gathered from a simulated mine entry was then used for computational fluid dynamics (CFD) modeling. The CFD analysis showed an improvement with The Eye CAN versus other accepted forms of standing roof support.This proof-of-concept study suggests that, when using this new product made by Burrell Mining Products, Inc., not only will the convergence from the roof and floor be controlled, but airway resistance will also be reduced.INTRODUCTIONOne of the basic elements of underground mining is the necessity to support the mine roof. It is well-known that easier reserves have been mined so that today's underground mines present challenging conditions. Factors influencing roof support decisions include mine depth, mining method, overburden composition, and agency regulations. Mining engineers, therefore, have to balance three objectives: safety, engineering, and cost. While safety is obviously paramount, and engineering often complements safety, the cost effectiveness of any product, method, or device warrants additional consideration in today's harsh business climate. Avenues for adaptation and improvement are found at the intersection of the three objectives."

Jan 1, 2016

By J. Hadjigeorgiou, T. R. Stacey

This paper introduces the Quantified Value-created Process (QVP), a decision-making process for use in mine design and operation. The implementation of the QVP is founded on a ten-step rock engineering design process and a ten-step strategic planning process. The potential of this approach is demonstrated by examples of value created as a result of good research, design, and planning. The QVP is divided into two parts, namely, a ‘planning the process’ section and an ‘implementing the process’ section, and can be considered to be an extension of the risk approach. All costs, direct and indirect, associated with a significant mining decision (design, operational, investment) must be quantified in advance of committing to that decision, to determine the value that will be created in the short, medium, and long terms. Ethical values, associated with health, safety, the environment, public perception, and social aspects, may be difficult to quantify in economic terms, but must nevertheless also be considered. In contrast with a traditional risk approach, the QVP will identify the upside, and allow executives to make more informed strategic decisions. In this context it is essential to actively engage upper management in the decision process.

Feb 2, 2022

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"NIOSH recently completed a 15-month study at an underground limestone mine crusher booth which evaluated three research parameters: (1) the effectiveness of a single-filter filtration and pressurization system for improving the air quality inside the operator booth, (2) comparing the effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) evaluating the use of three different pressure monitoring devices to determine the performance of the filtration and pressurization system over time. The protection factor was quantified monthly using particle counters in the respirable dust range (0.3–10 µm), and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static conditions and after outlier removal, the single-filter filtration unit installed offered a protection factor between 8 and 216, depending on the filter type and loading condition. The particle counting analysis shows that the ? > 95 filter offers a protection factor greater than 4-times that of the ? > 99 filter when evaluated over 60 minutes. The booth pressure monitors provided data that proved to be a valid indicator of system performance over time. INTRODUCTION Designed and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from physical hazards, such as flying rock, debris, and noise, as well as a more comfortable environment in regards to temperature and humidity [1]. But while it may be easier to quantify whether the A/C unit is working (measuring the temperature) or observe whether the cab offers protection from flying debris, it can be somewhat more difficult to quantify its performance in reducing respirable dust hazards. For over 15 years, NIOSH has been conducting applied research to improve the air quality inside of enclosed cabs of mobile equipment [2-5]. This work has led to the identification and mathematical modeling of enclosed cab filtration systems [6]. The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms [1, 7]. Stationary enclosures are similar to enclosed cabs; however, the volume of the work area can be significantly larger. In addition, workers who perform their duties in stationary enclosures tend to stay within the room for a greater percentage of the day, as opposed to workers on mobile equipment who may enter and exit frequently. Structural integrity can be easier to maintain as well, as there is typically less vibration and stress placed on these compartments as compared to mobile equipment. In addition to offering protection from dust and flying debris, enclosures must ensure that workers have a healthy supply of fresh air to avoid elevated levels of CO2, which are known to cause headache and dizziness, impairing cognitive function. The American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE) states that enclosures should have no more than 1,100 ppm of CO2 when outside levels are 400 ppm [8]. In addition, the American Society of Agricultural and Biological Engineering (ASABE) recommends a minimum airflow for enclosed cabs of at least 42.5 m3/hr (25.0 cfm) per person [9] to ensure an acceptable level of CO2."

Jan 1, 2017

By R. Zhang, S. Azam, S. Liu, J. H. Golbeck, V. Kurashov, S. Bhattacharyya

Free radicals (FRs) present in coal dust directly influence the interaction behavior between lung cells and dust particles. FRs are atoms or groups containing unpaired electrons, with strong chemical reactivity and a short lifespan. FRs which are quite persistent in natural environments, termed environmentally persistent free radicals (EPFRs), have recently received much attention as new environmentally hazardous substances. EPFRs present on coal dust serves as an active intermediary to catalyze reactive oxygen species (ROS) production by oxygen molecules endangering mine workers’ health. Many EPFR species may be bonded to the particle surface or trapped within the particle during coalification and can be modified with progressive size reduction through cutting at the mining face or crushing/pulverization in the plant. This study measured EPFRs for lignite, sub-bituminous, and anthracite coal dust at various sizes. We especially focused on EPFRs for submicron coal dust prepared by cryogenic methods. The outcome of this study will directly improve the free radical-dependent toxicity quantification and ultimately contribute to the size-dependent coal dust toxicity quantification.

Mar 2, 2022

By T P. Medhurst

In many cases mine design is the most important driver of the profitability of a mining project, however to reach an æoptimumÆ mine plan many compromises have to be made. Some of the fundamental profit (and loss) drivers relate to stoping methods and stope design parameters. Inevitably trade-offs have to be made between the stability of underground openings, ground support costs and production efficiency. This paper looks at the role of geomechanics in the mine planning and design process. The concepts of æcontrollable lossesÆ and æuncontrollable lossesÆ are developed as a means of partitioning ground control costs. A stope design example is given which provides a method of examining mining costs, and includes a decision making element in order to quantify geotechnical impacts and select stope dimensions. The method also provides a general framework as a means of balancing ground control costs against maximising returns from an underground mining project.

Jan 1, 2000

By P Cherepanskiy, G Elphick, R Hus, C Perring

When an iron orebody nears its end of life, the extracted material can become increasingly problematic to handle. Higher moisture content occurs as larger portions of originally-below-water-table material is mined, which in some deposits is accompanied by further changes in physical and/or chemical properties present along the edges of the orebody. Plant delays related to problematic material have affected all of BHP’s mining hubs to various degrees. Following the recent successful work in Yandi, where the development of an index to quantify the handleability of channel iron ore deposits resulted in an increase in extracted volumes and an extension to the expected life-of-mine, the value of implementing similar indices for bedrock iron ore deposits has been recognised. A materials handling index has been developed by combining observed empirical relationships between material properties and processing plant performance. Indices for each deposit were further refined and optimised by implementing a back-testing strategy which facilitated an understanding of what weighting or scaling each of the contributing components should carry to yield the highest success rate of predicting actual delays at a given plant. Currently materials handling indices are deployed to all mine sites and are made available in block models as well as calculated for individual blasthole and production samples. Values in block models are obtained by predicting the required properties using machine learning models, whereas hyperspectral data is used to ‘measure’ some of those properties on a sample level. This paper discusses the work that has been undertaken to obtain materials handling indices, the testing that has been done to optimise them, and what processes have been developed to ensure the best metrics are being used in the different planning and scheduling horizons to optimise extraction.

Jun 22, 2022

By B Reynolds

The process design for green- or brown-fields metallurgical plants typically starts with two fundamental elements: the detailed mass and energy balance and the plant flow availability. The detailed mass and energy balance is generally developed using process flow-sheet simulation software and represents the steady-state operation of the plant at normal operating conditions. The plant flow availability, also known as a range of other industry-specific terms such as ‘flow availability’ and ‘operating factor’, describes the ratio of plant production to the steady-state mass balance. These elements are then used together as the basis for equipment selection and design.Plant flow availability takes into account a myriad of production loss factors including planned and breakdown maintenance, feed availability and composition changes, variability in operational performance and the interaction of batch and continuous unit operations. The combined impact of these loss factors are complex and as such plant flow availability is usually derived using a top-down approach such as comparison to an existing operation, a group of similar operations or to an anecdotal ‘industry leading’ benchmark. These top-down approaches are fraught with risk however, as they cannot factor in changes to equipment selection, flow-sheet or plant operating philosophy, and can result in over-expenditure of scarce capital or shortfalls in plant production.The use of dynamic simulation to provide a bottom-up alternative to quantifying the plant flow availability in metallurgical plant design has been growing rapidly in recent years. It provides a technique to quantify the combined impact of the loss factors described here and a tool to support process design and equipment selection by facilitating a range of sensitivity and what-if analyses. This paper presents a case study of how dynamic simulation has recently been used to support the

Aug 8, 2011

By G Gilchrist, S C. Dominy, T Jashashvili, R C. A Minnitt

The grouping and segregation error is one of Gy’s seven errors that cannot be measured in any qualitative manner because of its transient and changing characteristics each time the sample is handled mechanically. Attempts to calculate the mean and variance of the segregation error is considered by some as ‘an exercise in futility’ that would not help us achieve representative sampling. This research is aimed at understanding the process of segregation of dense, finely divided and dilute particulate materials supported in a clean quartz substrate during intense agitation. Several mixtures of fine-grained materials including steel, tungsten carbide and gold grains were used in these experiments. Four hundred grains of each of the minerals and metals at a top size of 2 mm were mixed with approximately 600 g of finely ground quartz material (95 per cent passing 2000 microns) in a 500 ml plastic jar with a sealable lid. The mineral–?metal mixtures were analysed in three steps using microfocus X-ray computed tomography. Step one consisted of rolling the containers on a flat surface in an attempt to concentrate the mineral and metal grains in the core of the supporting substrate; this is a base case that can be reconstructed after each session of analysis. The second step involved gentle and vigorous shaking of the mixtures in order to segregate the denser minerals and metals from the supporting quartz substrate. In some cases, a third step involved splitting the sample through a riffle splitter. Three-?dimensional images of the surface of each grain, its volume and its X-, Y- and Z-coordinates, before and after intense agitation of the container, were interpreted from the reconstruction of the tomographic X-ray data. The spatial analysis of grains using cell declustering and 3D variography provided a useful means of characterising the distribution of the grains in space and the extent to which they had become segregated during the process of agitation. Spatial analysis indicates that in general, grouping and continuity of grains is weakly developed. The modelled nugget effect remains high for most tests, indicating that grains of similar size did not group together strongly. Agitation through rolling provided the best continuity, although not consistently in the long axis of the plastic jar. The nugget effect was consistently highest, and the range of continuity shortest in samples that had been split, indicating that the grouping and continuity were reduced through splitting the sample. Initial results indicate that very little segregation of the minerals and metals occurs in the quartz substrate. This is somewhat counter-intuitive, but suggests that the effects of agitation on mixtures of dense minerals and metals in substrates of lower density do not lead to excessive segregation. Differences in behaviour between dense materials in response to agitation are evident. Grains of different composition and shape did not group and segregate in a predictable manner in response to the agitation methods. Initial results indicate that the degree to which a material groups and segregates relates more to the characteristics of the denser material itself, rather than the agitation method employed.CITATION:Minnitt, R C A, Jashashvili, T, Gilchrist, G and Dominy, S C, 2017. Quantifying segregation of minerals and metals in particulate materials using computed X-ray tomography and variography, in Proceedings Eighth World Conference on Sampling and Blending , pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By J C. de Vries

When times are tough in the mineral industry û as they have been for some time û typical responses by mining companies are to cut costs and/ or increase production. The latter is seen to spread fixed costs, thereby also reducing unit costs per tonne mined. However, most mineral deposits respond to increased production rates by lowering ore grades, so the reduction in cost per tonne of ore does not necessarily result in a reduced cost per unit of metal produced. The authorsÆ experience is that this process often leads to a mine plan that is a long way from optimal. Producing to the point where marginal cost equals marginal revenue may work well in a manufacturing operation, but it is not necessarily the best strategy for a mining company with a depleting resource. Variations in tonnage and grade with depth, ore reserve optimism and a variety of other factors conspire to produce variations in production rates and grade that often result in suboptimal outcomes and potential mine failure. Added to this is the focus of industry analysts and senior corporate management on such measures as unit costs and ounces in reserves. This is perceived to have the perverse effect of driving the share price down when strategies are adopted that actually improve the value of the mining operation, and vice versa! Many mine failures can be prevented by a close examination of the tonnage grade curve and an understanding of how margins, net cash flows and resulting business risk change with cut-off grades and rates of production. A few relatively simple analyses early in the evaluation of a project can demonstrate the tradeoffs between the main decision parameters, leading to right-sizing of the operation. Once major commitments to major capital items have been made, and reserves have been publicly reported, optimisation of the operation becomes much more difficult than if it had been done earlier. Such investigations can also identify the upside potential and downside risks associated with factors outside the companyÆs control. Many strategies that may enhance value in the good times significantly increase the downside risk in the bad times. What is often called risk analysis typically looks at superficial issues, and does not evaluate the major factors leading to the potential for financial disaster. This paper illustrates some of these major risks, and demonstrates how they may be fully evaluated so that corporate decision makers can make fully informed decisions that take account of the real risks.

Jan 1, 2003

By C. Samson, R. S. Smith, S. W. Hefford

"Abstract - Time-domain electromagnetic systems are most sensitive to highly conductive targets during the transmitter on-time. Data collected during the on-time is highly influenced by the geometric relationship between the transmitter and the receiver. Unless corrections can be applied for these geometric variations, the ability to correctly detect and identify highly conductive targets can not be fully realized. Variables affecting the relative position between the transmitter and receiver include changes in the position of the receiver with respect to the transmitter, variations in transmitter attitude, and transmitter loop deformation. The level of accuracy in the determination of the relative geometry required to permit complete removal of the effects due to geometric variations is different for each of the variables and is dependent on the depth of the target. The most influential geometric variation involves changes in the relative position of the receiver with respect to the transmitter along the direction of flight; this variable, therefore, requires the highest degree of accuracy. The accuracy required for receiver motions along the vertical direction is roughly one order of magnitude less, and in the lateral direction, several orders of magnitude less. The objective of this paper is to relate the sensitivity of the response to transmitter-receiver geometry to the ability of an airborne, time-domain electromagnetic system to resolve a highly conductive vertical target. This is achieved by a detailed analysis of the effect of the individual x, y, and z distances between the transmitter and the receiver, the transmitter attitude (roll, pitch, and yaw), and transmitter deformation.Sommaire - Les systèmes électromagnétiques en domaine temporel sont particulièrement sensibles aux cibles à forte conductivité durant le temps d’excitation. Les données collectées durant l’émission du transmetteur sont fortement affectées par les relations géométriques entre le transmetteur et le récepteur. Si un facteur de correction n’est pas introduit pour tenir compte de ces variations géométriques, la capacité de ces systèmes à détecter et identifier correctement les cibles fortement conductrices ne peut pas être pleinement réalisée. Les facteurs affectant les positions relatives du transmetteur et du récepteur comprennent les changements de position du récepteur relativement au transmetteur, les changements d’altitude du transmetteur et la déformation de la boucle du transmetteur. Le degré de précision requis pour déterminer la configuration nécesaire pour compenser complètement l‘effet des changements géométriques est différent pour chacune des variables et dépend de la profondeur de la cible. Les changements géométriques qui ont le plus d’influence sont ceux qui font varier la position du récepteur relativement au transmetteur dans l’axe de la ligne de vol; c’est donc cette variable qu’il faut contrôler avec le plus de précision. La précision requise pour le suivi des mouvements du récepteur le long de l’axe vertical est moindre d’environ un ordre de grandeur, tandis que selon l’axe latéral elle est diminuée de plusieurs ordres de grandeur. Le but du présent article est d’établir comment la susceptibilité de la réponse à la géométrie transmetteur-récepteur affecte la capacité d’un système électromagnétique en domaine temporel aéroporté à reconnaître une cible verticale fortement conductrice. Cet objectif est atteint par l’analyse détaillée de l’effet individuel des distances x, y, et z entre le transmetteur et le récepteur, l’attitude du transmetteur (lacet, roulis, tangage) et la déformation du transmetteur."

Jan 1, 2006