Search Documents

By G. R. Lehman

The Inspiration Consolidated Copper Co. had an orebody at Miami, Ariz., of close to 100,000,000 tons of low-grade copper ore, and the method of mining this ore most profitably was of great importance. The selection of a method was practically limited to a "top-slicing," a "shrinkage-stope" or a "caving" method. The "top-slicing" method would give a high extraction of the developed ore, at a high mining cost, and the "shrinkage-stope" or "caving" methods a lower extraction of the developed ore, at a lower mining cost. Ore-Drawing Tests To decide on the method to be used it was necessary to know about what extraction of the ore could be obtained by the "shrinkage-stope" or " caving " methods. As no definite information regarding the,question was available at the time, C. E. Mills, the general manager, thought that some information could be obtained by experimenting in drawing ore, covered with capping, from an experimental box. Some work had already been done along these lines by W. C. Browning for the Inspiration Copper Co. and by myself for the Live Oak Development Co. The idea was to represent as nearly as possible, in the experimental box, the conditions within an area of caved stopes of caved ore all ready for drawing. That is, the area was supposed to represent a semibroken mass with the capping above it in the same condition and ready to follow the ore downward as it was drawn out of the chutes under the ore. To represent the above condition, in the experimental box, crushed ore from the mine was placed in it to a given height, and red barren capping from the mine was placed on top of the ore. The Experimental Box The experimental box shown in Fig. 1 was made of wood and glass. The glass was used for the sides so that the drawing action of the outside row of chutes could be seen and noted, the latter being cut in the center by the glass sides. The length of the box was 30 in., width 20 in. and the

Jan 1, 1917

Clarence M. Haight, Franklin Furnace, N. J. (communication to the Secretary*).—In that part of Mr. Wilson's paper describing the Gilman cut-and-fill system, a few features do not appear to be fully explained. In what way is the waste used for filling obtained? The text mentions that if waste is encountered when driving the filling raises, these raises are stopped until the fill is needed; that seems to suggest mining the capping for fill, which might make the backs of the stopes bad as the stopes approach the top of the ore. If, on the other hand, the fill is brought to the raises in cars, are the crosscuts that are necessary in ore or waste? Is the cost of this fill included in the stoping costs given? The second, or lower, series of stopes will present a different problem to that which the first series (under the capping) gave. Although no mention is made in the text, it would seem that the second series of stopes will have to be worked on center lines which are offset half the stope width, 20 ft., from the centers of the stopes above, in order to take advantage of the "rafter" effect of the stringers so named. How is the fill to be introduced into the lower stopes? There are no crosscuts mentioned to provide for this; or is it intended to tap the filled stopes above for the fill? In the latter case the method of control of this fill will be of interest. Ore that will admit of a stoping width of 40 ft. with the lengths mentioned in the description is stronger than any with which many mining men are familiar. Has the practice of starting to mine a second stope before the preceding one is filly completed been tried to any extent? If

Jan 1, 1917

By Edwin M. Chance

During the last decade many conditions have been encountered that have materially increased the cost of the production of coal. As in most cases it has not been practicable to increase the selling price of such coal sufficiently to insure the necessary margin of profit, the mine management has been forced to avail itself of what might be termed unusual means that costs might be held at as low a figure as possible. The so-called efficiency engineer has been called upon, costly power plants have been built and machinery has been installed to replace manual labor wherever possible. Another aid used recently to secure economies through the more intelligent production of coal, is the chemist. As the coal industry, barring the production of byproduct coke, does not at once give evidence of its need of the services of the chemist, the writer will endeavor to point out a few of the services that this branch of the staff has been able to render. The preparation of coal in the past has been carried on entirely upon an empirical basis, that is, the criterion adopted has been an ocular inspection. Unfortunately, the appearance of a coal and especially of an anthracite, has but little relation to its fuel value, and as long as coal is purchased for the heat that can be obtained from it by its combustion, the quantity of such heat that is purchased must be one of the principal desiderata in selecting or preparing a coal. Were coals purchased for use as bric-a-brac or for exhibition in museums it might be both wise and just to purchase them upon their appearance. After 4 or 5 years of investigation the fact has been established that coals of very inferior appearance, and I now have special reference to anthracite, might and often did possess heating and burning properties superior to those possessed by bright coals which in the past had commanded considerable and uniform premiums in the market. This being the case the question arose as to whether the trade could be convinced of this fact. While at first some difficulty was experienced in establishing the quality of such dull coals, still it was found that the real obstacle to the sale of these materials in the past had been the fact that the coal producers' own sales departments felt convinced of the inferiority of this type of fuel and when complaints were registered they were given ready credence. Upon convincing the sales department of the quality of this type of fuel, but

Jan 1, 1917

By L. O. Howard

What was perhaps the first attempt at basic converting in the Southwest was made by the late Charles F. Shelby at Cananea early in 1907, when he removed the acid lining from one of the 8 by 12-ft. barrel-type converters then in use at the reduction works of the Cananea Consolidated Copper Co. and substituted a lining of one course of magnesite brick. In this shell, he blew 21 taps (about 180 tons) of matte to white metal before the brick gave out along the tuyhre line. In every case, the white metal so made was transferred and blown to copper in other converters. The cost of the lining was $700 and Mr. Shelby gave up the experiment as impracticable. No further serious effort to bessemerize copper mattes in a vessel having a more or less permanent lining of basic brick was made by any of the large copper smelters in the Southwest until some months after Messrs. Peirce and Smith had brought the question permanently before the public, and had proved it to be a metallurgical and financial success by their work at Baltimore and Garfield. Early in 1911, the Cananea Consolidated Copper Co. had in operation at its reduction works at Cananea, Mex., several 8 by 12-ft. barrel-type converters lined with magnesite brick which had previously been operating with acid linings. In the 18 months following, these converters produced 50,000 tons of copper. In June, 1912, this company installed the first of its new equipment of six stands of electrically operated 12-ft. Great Palls type converters, and shortly afterward discontinued the use of the smaller shells. In September, 1911, the Consolidated Kansas City Smelting & Refining Co. had installed at its El Paso plant two 10 by 26-ft. Peirce-Smith converters. Later, in March, 1913, one standard Great Falls type converter was added. About the time the Peirce-Smith converters were going in at El Paso, the Calumet & Arizona Mining Co. was experimenting with basic linings in 7-ft. by 10-ft. 6-in. barrel converters at its plant in Douglas, Ariz. These efforts were sufficiently successful to enable the plant to "handle the total output of copper in these small shells until the standard Great Falls converters were substituted in June, .1914.

Jan 1, 1917

By Charles T. Steuart

The Arkansas Novaculite of Devonian and Mississippian age is the most distinctive formation in the central Ouachita Mountains of Arkansas from the standpoint of both topography and lithology. The formation typically forms precipitous, narrow ridges (hogbacks) which reflect the steepness of dip and the resistance and thickness of the rock units. The Arkansas Novaculite varies from less than 200 feet thick in the north to locally over 800 feet thick in the south and outcrops over an east-west distance of 360 km (200 miles) in the Ouachita Mountains of Arkansas and Oklahoma. Most of the rocks of the formation are highly siliceous with novaculite predominating, and lesser quantities of chert, siliceous shale, conglomerate and rarely sandstone. Novaculite is commonly defined as a homogeneous mostly white rock, translucent on thin edges with a dull to waxy luster and composed almost entirely of microcrystalline quartz. The word novaculite comes from the Latin word novacula, meaning razor hone. This term was first used by Richard Kirwan in his mineralogy text of 1784. The origin of novaculite remains controversial but we believe it was a primary silica derived mostly from the alteration of submarine volcanic-rich materials, with numerous fine biogenic components and some minor clastics (derived mostly from foreland facies via turbidity currents) and deposited as an amorphous siliceous ooze in the deep Ouachita trough. It was subsequently converted to microcrystalline quartz during diagenesis by the compaction of the overlying rocks and the intense Late Paleozoic Ouachita Mountain tectonism. In the central and southern portions of the region three divisions of the formation have been defined: a Lower Division predominantly of light-colored novaculite; a Middle Division of interbedded dark chert and shale; and an Upper Division of massive often calcareous novaculite. In the northern exposures the formation is thinner and contains more black chert and shale, chert-shale conglom¬erate, sandstone and less novaculite. The massive novaculite of the Upper and Lower Divisions is a source of high purity silica (99+%). Indians were the first to use novaculite. They made their various tools and hunting implements from the weathered broken rock until they learned the quarrying techniques. The first white men in the area recognized the use of novaculite for sharpening their tools and knives: previously whetstones were obtained in small quantities from Europe. To this day whetstone is quarried mostly in areas which the Indians and possibly the Spanish previously worked. Some of the current mining practices have changed very little from those of the early quarryman. In areas where the novaculite of the Upper Division is poorly cemented, this friable tripolitic material has found applications in such uses as an abrasive, as a filler or extender in paints, plastics and other purposes. Some of the dense novaculite is suitable as a filler in fire bricks and also in plastics. Because some of it has the tendency to decrepitate when heated not all novaculite can be used for these applications. Several quarry operators are crushing novaculite for road, concrete, and other aggregate. This use was formerly rather limited due to the abrasiveness of the novaculite on crushing and screening equipment. Further potential uses of novaculite are speculative but include application of high purity silica in the production of silicon metal for solar cells, seed or "growing", and fusing quartz for electronics.

Jan 1, 1985

By Albin E. Anderson

The PSM System has been available to the mining industry for nine years. During this time, many of the more than 160 Systems sold have been put to practical use and have provided the owners a handsome return on investment. In this paper, the author will briefly discuss how the System works and how it can be put to use in automatic grinding circuit control. Throughout, detailed consideration will be given to the many factors that can significantly influence how successful a specific application is.

Jan 1, 1979

By R. Weber

Methane explosions in underground coal mines are a major concern across the mining industry. After the Pike River disaster, Arnot Coal became even more aware of the explosion risk. To determine whether Arnot has adequate precautions against a methane explosion, such as the one that led to the Pike River disaster, a literature survey covering the causes of the incident and what preventative measures should have been in place was conducted. Many different methane explosion prevention methods were evaluated, as well as codes of practice. Based on the findings, Arnot?s measures to prevent conditions favourable for a methane explosion were evaluated.

Jan 1, 2014

By John C. Cosgrove

IT was just five minutes past midnight, on Wednesday, Jan. 5, 1938, that Mrs. Cosgrove and I sailed from New York City. Our trip was to completely circle the globe, to cover over 40,000 miles and stop at thirty ports-from New York to Trinidad, to South America, via South Africa to the Orient, to India, to the Malay States, to Indo-China, the Philippines, Australia, New Zealand, Fiji, and across the Pacific home via Honolulu. It is not my intention to make this a complete, technical study of coal or coal mining in the various countries that .we visited but more to outline the general in- formation that the mining engineer and coal operator would absorb in his travels. Coal is the universal fuel and is in use wherever there is commerce and industry. Even on our ship, which, like practically all ocean liners was an oil-burner, a considerable quantity of coal was used for cooking.

Jan 1, 1939

By B. Hohenstein, B. McBain, B. de Jong

"The automated fire assay system (Fast In-line Fire Assay or FIFA) has not found acceptance in the Au mining industry as the lower measurable limit of 0.20 ppm did not allow Au tailings to be measured with confidence. The development of arrested cupellation has overcome this hurdle which was a limiting factor in the FIFA 1 process. In the new automated fire assay process, automated sample preparation, fluxing, fusion and separation of a Pb button are essentially similar to the FIFA 1 process, albeit with some improvements. However, the game-changer is the development and incorporation of arrested cupellation into the automated system, now called FIFA 2. The purpose of arrested cupellation is to reduce the 50 g Pb button to a 5 g Pb button by partial cupellation in a specially developed arrested cupellation system thereby concentrating the Au in the Pb by a factor of 10 and in so doing moving them into higher concentration ranges in the mini-button where they can be read on the spark spectrometer. Results show that concentrations down to 0.02 ppm Au in geological materials can now be determined using arrested cupellation in the FIFA 2 process, an order of magnitude improvement over FIFA 1.INTRODUCTION Traditional fire assay for Au has remained virtually unchanged for 3000 years. It has survived for so long because it is accurate, has relatively low detection limits and is relatively inexpensive. However, it is labour intensive, has a long turn-around time (typically at least 7 hours), is environmentally unfriendly and exposes assay operators to potentially unsafe conditions (toxic fumes, toxic dust and extreme heat from furnaces). The NiS collection method is not as effective for the assay of Au as it is for the PGEs. A rapid, accurate, cost-effective method for the determination of Au and the Platinum Group Elements (PGEs) in geological materials would be a tremendous benefit to mining companies. Many of these objectives have been met by the FIFA 1 (Fast In-line Fire Assay) developed some 15 years ago in which automated methods have replaced the manual procedures which are part and parcel of conventional fire assay. However, concentrations below 0.2 ppm have been very difficult to achieve with sufficient reliability."

Jan 1, 2017

By Gavin Beer

The Chelopech Copper/Gold Mine, located in west-central Bulgaria, has been in operation since 1953 producing a low-grade copper/gold concentrate containing up to six percent arsenic by weight. The penalties and restrictions imposed on smelting this concentrate, have seen the past operators of the mine strive to find a balance between achieving acceptable metal returns from the smelters and installing novel or unproven technologies in the face of changing political and economic climates. This paper documents the colourful history of the concentrate processing alternatives that have been investigated and implemented over the 45 year life of the Chelopech Mine, culminating in the high pressure oxidation option that is now the focus of a Definitive Feasibility Study (DFS) presently being undertaken by GRD Minproc Limited. The fundamental chemistry of the preceding alternatives is outlined followed by a discussion as to why each was ultimately not employed. A detailed description of the technology proposed in the DFS is given including: pressure oxidation, arsenic fixation, SX/EW copper recovery, CIL gold recovery and AVR/SART cyanide/copper recovery processes. Keywords: Arsenic, Scorodite, HPOX, Chelopech, Dundee

Jan 1, 2005

By Esther Carrera Martinez

Caraiba Metals is the sole brazilian copper custom smelter. The sulfur present in the various concentrates processed is recovered as sulfuric acid and oleum ,which are sold in the local market For quality assurance purposes, a study was carried out in order to determine how to control the arsenic content in the acid, allowing the continuous processing of concentrates with high levels impurity, The study was based on the process parameters of the washing towers and mist precipitators, Others process variables were investigated and their effects were used in support to confirm the results, After many analyses performed some interventions to improve the quality of the acid were implemented in the plant, which proved to be successful even by using a conventional purification system,

Jan 1, 1996

By D Craw, C Smith, C Rufaut

Oceana Gold (NZ) LtdÆs, Macraes Gold Operation currently has two tailings impoundments, the larger of which covers approximately 75 ha. When an impoundment is temporarily out of use, the surface dries and dust can be blown from the surface to the surrounding area. At present water spraying is used to stabilise the surface, but this is not ideal as Macraes mine can experience water shortages during the summer. This paper examines an alternative method of surface stabilisation using vegetation as a ground cover. The tailings have a low natural fertility, so it is important to determine what will actually grow in the tailings, and whether amendments are necessary. Also important is the effect of the amendments on arsenic mobility in the tailings as the schist rock at Macraes has naturally elevated levels of arsenic. Three plants species, rye corn, barley, and lupin, were grown in metre-deep lysimeters at Macraes mine site. The plants were grown in unaltered tailings, and tailings with one of two amendments added: Bioboost (an organic fertiliser containing biosolids), and superphosphate fertiliser. The leachate from each lysimeter was collected and analysed monthly to determine the extent of arsenic mobility. In addition, laboratory experiments were set up to determine arsenic mobility in tailings with amendments at the centimetre scale.   All plants grew best with the fertiliser amendment, with rye corn growing the best overall. Plants growing in unaltered tailings either barely survived (rye corn, barley) or died (lupin). Plants in the Bioboost amended tailings grew only slightly better than in the unamended tailings. Laboratory experiments indicate that the addition of phosphate fertiliser greatly increases arsenic leaching at the centimetre scale when compared to unamended tailings. The addition of Bioboost only marginally increases arsenic leaching, compared to unamended tailings. This trend has not been repeated in the lysimeter trials on the metre scale over four months. Current results suggest that of the plant types trialed and amendments used, rye corn with superphosphate is the most practical short-term tailings stabilisation method at Macraes.

Jan 1, 2004

By A. B. Young

THERE were produced in this country in 1923 probably in the neighborhood of 12,000 or 13,000 tons of refined and crude arsenic, by far the greater portion coming as a by product of smelting operations. Early this year copper smelters were producing arsenic at the rate of about 425 tons per month and lead smelters at the rate of 7;0 tons per month. During the entire eighteen years prior to 1919, there were produced in the United States only 47,000 tons of arsenic, which amounts to only 25 per cent. of the present output. The great increased demand has come about through the augmented use of arsenates as insecticides and arsenates as weed killers. In an extract from "Mineral Resources of the United States" on "Arsenic in 1922," Messrs. Heikes and Loughlin say, "The minimum possible demand for arsenic in 1923 was estimated at the end of 1922 to be about 13,000 tons, including 2000 tons for plate glass manufacturers, 3000 tons for lead arsenate, 3500 tons for calcium arsenate, 1500 tons for weed killers, 1200 tons for Paris green, 1000 tons for sheep dips and 750 tons for proprietary mixtures. More recent information, however, indicates twice as great a demand for calcium arsenate." The latter has found great use in the last three or four years as a weapon to combat the boll weevil pest of the southern cotton belt. ~t the present writing refined white arsenic is being quoted on the New York market at from 13)d c. to 1455 c. per Ib., while the average price during the eighteen-year period just mentioned was 4.8 c.

Jan 1, 1924

By D. Laguitton

The basic chemistry of a1•senic related to its dissolution and subsequent precipitation in gold-mine waste waters is discussed. The lime addition methods provides the most economic treatment of arsenical slurries, but requires a careful control of the oxidation of Asm into Asv, of the pH (>12) and the filtration of the precipitate. If arsenic levels below 0.5 mg/ l are required, a modification of the method by phosphate addition must be considered.

Jan 1, 1976

By AIME

WE got our chance to talk with Arthur J. Blair at the Annual Meeting at the Pennsylvania Hotel. By two o'clock Wednesday afternoon things had quieted down enough so we had our interview in the foyer to the Ball Room. There were the usual questions. Where were you born? In La Salle County, Ill., on March 26, 1885. Where did you go to school? Northwestern University, B.S. degree in 1906. Where did you start work? For E. J. Longyear right after leaving school. One's ability as a geologist was measured by one's ability to wield a brush hook and ax. He stayed on the job as geologist for three years and then got to thinking about the advantages of a warmer climate. The advantages stacked up favorably, so off he went to Birmingham, Ala., just about the time U.S. Steel took over the Tennessee Coal, Iron and Railroad Co.

Jan 1, 1948

By P Mugebe, M Yahyaei, M S. Kizil, R Low

This paper seeks to establish an empirical relationship between the impact of mining technological innovation implementation and a company’s market value. The company’s market value is represented by its stock price. In a bid to ascertain the relationship, a stock price prediction model is sought to be established using the firm-specific factors impacted by the implementation of innovative technology. This work is performed under the watch of the prevailing macroeconomic factors. The background anchors in the understanding that the difference between the economic status of a mineral deposit and its uneconomic status lies in the level of mining technological innovation most prevalent at a given time (Hartwick, Olewiler and Preuss, 1986; Wellmer and Scholz, 2017; Wright and Czelusta, 2003). This is derived from productivity improvement, resulting in sustainable profitability due to technological innovation. Unfortunately, there is not an adequately established relationship that links this technological innovation impact to the share price performance of the mineral commodity company.

Sep 1, 2024

By Paweł Stefaniak, Natalia Duda-Mróz, Sergii Anufriiev, Wioletta Koperska

Due to the high environmental risks and negative impact of a failure, tailings storage facilities (TSFs) need constant monitoring. Advanced mathematical models have been developed in the past to predict the behavior of TSFs and raise alerts if needed. To be precise and reliable, such models need a spatial distribution of soil types within the dam as an input. Getting this data from laboratory measurements is time and costconsuming. In this article, we propose an ANN-powered algorithm, which allows us to accurately estimate the soil distribution based on a cone penetration test (CPT).

Jun 25, 2023

By Sepideh Javanshir

The process of liquid?liquid extraction of gold from chloride solution is complicated by the presence of many variables acting simultaneously in an unknown non-linear fashion for the determination of the final extraction efficiency. In practice, it is quite difficult to develop a model for predicting various properties of such process. Therefore, an alternative approach based on Artificial Neural Network (ANN) is considered to assist in the simulation process. Artificial neural networks (ANN) are powerful tools that can be used to model and investigate various highly complex and non-linear phenomena. This paper presents application of Multi-Layer Perceptions (MLP) to construct relationship that will be employed to develop a quantitative method for the estimation of the extraction efficiency as a function of hydrodynamical parameters such as stirrer speed, [AuCl4]- and DBC concentration, organic and aqueous flow rate. The model is shown to be in excellent agreement with the experimental data (R2 value for training and testing data was 0.9992 and 0.9915 respectively). Therefore, it can be used to optimize the parameters of liquid?liquid gold extraction with dibutyl carbitol (DBC).

Sep 1, 2012

By Daniel Hodouin

Artificial neural networks (ANN) are of growing interest in a wide variety of applications. Pattern recognition, speech processing, financial analysis, signal processing and process control are at present the most successful ones. This paper is an attempt to illustrate the potentiality of ANN applied to mineral processing. An introduction to the technology of ANN is first proposed to describe the various components and to explain the various phases encountered in setting up a network. Then examples are given to illustrate the use of ANN dynamic modelling of mineral processing units or plants and in process control.

Jan 1, 1991

By Dan Yang

Pile foundation designs are performed routinely based on geotechnical information available at the time of design, often with due consideration of large uncertainties inherent to soils and site conditions. These uncertainties frequently are the causes of piles being installed not the same as those designed, especially by factors beyond quality assurance and quality control. With a variety of both satisfactory and unsatisfactory pile test results from these nonconforming piles, the design engineers are required to examine the foundation performance as a whole against the project design requirements before signing off on them or calling for potentially costly remediation. Over the years, as-built analysis has been a consistent way of dealing with pile non-conformity and damage in our practice, avoiding many construction delays and it is an integral part of our pile foundation design. In this paper, the key elements of an as-built analysis along with several major bridge projects are presented.

Jan 1, 2010