Search Documents

By T. F. Curry, L. B. Berger, H. A. Watson, S. J. Pearce

The conduct of work at elevated air pressures , such as in caissons and in tunnel - driving in subaqueous strata , poses safety problems not encountered in mining and tunneling operations at ordinary atmospheric pressure . This publication discusses some of the problems involved and presents information on the following subjects : ( 1 ) Physiological effects of gases at elevated pressure . ( 2 ) Use of respiratory protective equipment in rescue or recovery operations in event of fire or other emergency in pressurized tunnels . ( 3 ) Effect of elevated pressure on performance of some gasdetecting instruments ; interpretation of the results . Various types of respiratory protective devices are discussed in relation to their possible use at elevated pressures , especially the 2 - hour , selfcontained , recirculating - oxygen - breathing apparatus , which has had wide use in the United States during rescue and recovery work in the mining industry . A modified procedure that eliminates the hazard of oxygen poisoning enabling the safe use of this apparatus at elevated pressures , up to 45 pounds per square inch , gage , and tests to verify its practicability are described . procedure involves control of the partial pressure of oxygen in the breathing

Jan 1, 1964

By Harold M. Smith

The data in this report were prepared to show how Bureau of Mines routine crude oil analyses could be used to evaluate crude oils in terms of common commercial products . The use of Bureau of Mines routine analyses to determine hydrocarbon - type relationships for the gasoline and gas - oil fractions is demonstrated . For this purpose the correlation index , the aromatic profile and the naphthene profile are used to establish reasonably acceptable values for hydrocarbontype relationships . The derivation and meaning of these indications are discussed . These analytical interpretations are applied to a group of high - sulfur crude oils from the Near East , the Permian basin of West Texas , Venezuela , Colombia , California , and other locations , and the resultant data for gasoline , gas oils , lubricating oils , and asphalt are compared by appropriate tables and graphs . Because the Near East crude oils contain higher quantities of paraffins in the gasoline and gas oil ranges , they will yield good , lowsolvency solvents and good kerosine , jet fuel , and diesel fuels , but straightrun gasoline of inferior quality compared to similar products from either West Texas or Venezuelan high - sulfur oils . The Near East oils also should be good sources of lubricating stock . However , when used as stock for catalytic cracking or reforming , the Near East oils suffer by comparison because they are deficient in naphthenes .

Jan 1, 1964

By Robert M. Becker

This report (the second in a series of five) presents the mathematical development in extending the theory of sample reliability from a sample consisting of a fixed number of items to a sample consisting of a fixed amount of items. Examples of a fixed amount of items per sample are samples consisting of a fixed weight or a fixed volume of unequal size particles. The probability distribution functions (those here called the compound binomial and compound multinomial functions) are developed from fundamentals. Their distributions are generalized to include some measured characteristic of the items. Infinite population moments are derived from moment-generating functions, while finite population moments are developed from corresponding infinite population moments using the finite probability operator defined in part 1 of this series.

Jan 1, 1964

By William R. Wayment, David E. Nicholson

A modified percolation - rate test is proposed for use in determining flow rates through hydraulic backfill ; in contrast to the conventional test , a percolation- rate versus void - ratio relationship is established . requirements and a detailed test procedure are described . Equipment Results of a conventional test are compared with those of the proposed modified test . The proposed modified test method yields more accurate , realistic , and usable percolation- rate ( permeability ) data . The significance of obtaining accurate percolation rates for use in analyzing waterflow through hydraulic backfill is discussed .

Jan 1, 1964

By R. W. Hiteshue, R. W. Fridy, W. Kawa

A study of the production of coronene , a high - melting ( 440 ° C ) , highboiling ( 525 ° C) , polynuclear hydrocarbon , was made by the Bureau of Mines to determine the maximum yield obtainable by the hydrogenation of coal and coalderived materials . Experiments were made with anthracite and bituminous coals and with asphaltenes and centrifuged residue obtained from heavy oil produced in a pilot plant by the hydrogenation of a bituminous coal at 2,000 psi and 480 ° C. With anthracite , yields of coronene of 0.5 to 0.7 wt pct of moistureand ash - free coal were obtained at 6,000 to 8,000 psi , 700 ° to 750 ° C , and a residence time of 30 minutes . With bituminous coal , yields averaging 0.4 wt pct of maf coal were obtained at 6,000 psi , 800 ° C , and 30 minutes ' residence time . With asphaltene and centrifuged residue , yields of less than 0.02 wt pct of maf coal were obtained at 6,000 psi , 700 ° C , and 60 minutes ' residence time .

Jan 1, 1964

By R. S. Lang, C. C. Merrill

The recovery of zinc from oxidized zinc minerals by the caustic soda leach and electrolytic or chemical precipitation was investigated . With the exception of willemite ( 2 ZnO • Si0₂ ) oxidized zinc minerals were readily soluble in 180 to 240 g / 1 NaOH solutions . A high- grade zinc flake was recovered electrolytically from solutions which had been treated with zinc powder to precipitate copper and lead . Solutions were recycled to the leach stage with a recovery of about 85 percent of the zinc from an ore containing 21.2 percent zinc . Electrolysis was conducted at a current density of 120 amp / ft2 with a power consumption of about 1.5 kwhr /lb zinc . Zinc was also recovered from leach solutions by dilution of the solutions , carbonation of the solution , or the addition of sulfur to boiling solutions . A dilution ratio of 5 : 1 precipitated 59 percent of the zinc in 9 days . Carbonation of the solutions precipitated the zinc as zinc oxide ( ZnO ) and solutions could be recausticized for recycling . Zinc precipitated as the sulfide with sulfur was easily filtered and washed . Approximately half of the sulfur added to solutions was lost in the form of sodium thiosulfate ( Na S₂03 ) .

Jan 1, 1965

By Mulligan John J.

The Bureau of Mines investigated lode tin deposits on Potato Mountain, Seward Peninsula, Alaska. Tin was found to occur as cassiterite associated with quartz, tourmaline, pyrite, arsenopyrite, and earthy clays, but the deposits lack the varied accessory minerals commonly found in tin districts. The tin-bearing deposits are in metasediments along minor breaks and bedding planes but not in the crushed earthy filling of major faults. Cassiterite and sulfides occur with quartz in veins, both with and without earthy clays, and disseminated through tourmalinized wall rocks. The deposits are characterized by irregular segregations containing 1 to 10 percent tin within zones averaging not over 0.25 percent tin. The largest segregation exposed is on the summit of a low hill on the east-central slopes of Little Potato Mountain; most of the outcroppings are in an area trending east to west, roughly 10 to 30 feet wide and 300 feet long. Sample values ranged as high as 12 percent tin, but the average grade may be about 1 percent tin. The extreme irregularity of both grade and composition precludes a more exact determination. Similar concentrations are scattered for over 1,000 feet to the west and north, but these are smaller and lower in grade. Elsewhere on Potato Mountain, generally similar deposits occur as clusters of veinlets at widely separated points in the metasedimentary walls of major faults.

Jan 1, 1965

By Tilman M. M.

The effects of substituting cobalt for nickel on the acid corrosion resistance of two types of austenitic stainless steel were determined. Cobalt substitutions to a maximum 2.2 weight-percent were made in types 302 and 309 stainless steels. Total immersion corrosion tests were made in 10 volume-percent hydrochloric acid, and boiling-acid tests were conducted in 65 weight-percent nitric acid and in undiluted glacial acetic acid. For modified type 309 in acetic acid, corrosion rates decreased for additions greater than 0.57 weight-percent cobalt. Corrosion rates increased as cobalt was increased up to about 1 weight percent for modified type 302 in nitric and hydrochloric acids and for modified type 309 in nitric acid, but these rates decreased with a further increase in cobalt content. A gradual increase in corrosion rates with increasing cobalt content was shown for type 302 in acetic acid and for type 309 in hydrochloric acid. Cobalt substitutions in larger amounts (above a ratio of 8 Ni to 1 Co) may increase the corrosion resistance of the austenitic stainless steels.

Jan 1, 1965

By Robert M. Becker

This report (part 3 of a five-part series) presents computer programs for evaluating moments and moment relationships of the generalized probability distributions extended or developed in parts I and 2. The principal program is for evaluating the first three moments and moment relationships of the compound-multinomial distribution for finite as well as for infinite populations. This is the generalized distribution for sampling to some amount of items per sample. Another program is for evaluating the first four moments, the moments of the mean, and the moment relationships of the multinomial and generalized hypergeometric distributions. This is a general moment program in sampling to some number of items per sample or for sampling to some number of samples. This program will accept either ungrouped data, frequency data, or probability data.

Jan 1, 1965

By Jr. Frank Parrish

This report describes the performance of 17 selected water-injection projects producing from Pennsylvanian-and Permian-age reservoirs. Illustrations depict reservoir structure and thickness, and production and injection history. A selected bibliography of publications pertaining to area oil recovery and geology is included. Tabulations of field and reservoir data reveal marked differences in the projects. Increased oil recovery resulted from injecting water in most cases; however, seven projects recovered less oil than the operators anticipated. Oil recovery by water injection ranged from 0.2 to 262 bbl per acre ft, or 0.1 to 22.5 pct of the initial stock-tank oil in place. Major reasons suggested for poor performance include: (1) Adverse directional horizontal permeability, (2) channeling of injected water through fractures or zones of high permeability, and (3) lack of containment of injected water. One 330-foot-deep project is among the first successful shallow water-floods in north Texas. Another project is the first successful Canyon sand-stone waterflood reported in the area. Previous gas injection in two Cisco sandstone projects did not prevent the reservoirs from responding favorably to waterflooding.

Jan 1, 1965

By Manuel Gomez

The heat contents of thermally dried lignite, subbituminous B coal, and their corresponding low-temperature chars were determined at various temperatures below the highest temperature to which these materials had been exposed before testing. Similar studies were made on high-temperature char and coke, spent shale, and ash prepared from both coal and spent shale. Heat content of the carbonaceous materials tested correlated well with temperature. Heat con-tent results for spent shale compared well with the published results. Statistical analysis of experimental data together with published information showed moisture, volatile matter, carbon content, and temperature to be the principal variables influencing the specific heat of coal. The specific heat of devolatilized carbonaceous substances, char and coke, approached that of graphite as the carbonization temperature was increased. The elemental specific heats of coal constituents, estimated from the ultimate analysis and the specific heat of coal, compared favorably with published elemental specific heats.

Jan 1, 1965

By M. R. Geer

Samples of coal from six beds in the Roslyn-Cle Elum field of Washington were subjected to float-and-sink tests to determine their amenability to the production of high-ash boiler fuel for on-site power generation. Grindability tests and analyses of ash were made. All of the coals would require some degree of cleaning to insure a product of 25 percent ash. With two of the coals the entire size range would have to be washed. With the other four, it would suffice to clean only the coarse coal and bypass the raw fines.

Jan 1, 1965

By Richard F. Hewlett

This report describes how a limited number of preliminary exploration drill-hole assays from a mineral deposit can be used to design grid spacing that is both economic and efficient for subsequent evaluation drilling of that deposit. Relationships between desired precision of the estimate of grade of ore and drilling cost are used to determine the economic drill-hole spacing. The statistical concept of precision in estimating grade of ore is used to determine the efficient drill-hole spacing. Assay data from approximately 50 known copper deposits were studied, and the relationships of the statistical parameters of these deposits were computed. Drilling requirements for various precisions of the estimates of grade of ore were computed for some of these known deposits to serve as guides for drilling future copper deposits. The effect of various geologic factors on the trend in grade of ore and, therefore, on the drilling requirements is shown for certain deposits.

Jan 1, 1965

By H. E. Powell

Basic data were recorded on the decompositions that take place during thermal decomposition of siderite (FeC03). Both the naturally occurring and a synthetically prepared mineral were studied by differential thermal, thermo-gravimetric, X-ray-diffraction, and chemical (including gas) analyses. Thermal decomposition was studied in the media of dry air, moist air, dry carbon dioxide, dry helium, and dry carbon monoxide and at atmospheric and at reduced pressures. Results showed the thermal decomposition of FeC03 to be an extremely complex process, dependent on environmental factors and side reactions that cannot now be completely controlled. Therefore, full understanding of the reaction involved must depend on additional research with advanced evaluation techniques.

Jan 1, 1965

By Jr. Joyce

This report describes sulfatization of nickeliferous laterites from Puerto Rico and the Philippines for recovery of water-soluble nickel and cobalt sulfates. Temperatures ranging from 665 C to 710 C and a 10-percent sulfur dioxide-air reaction gas were employed during batch-roasting tests and during continuous countercurrent treatment in a 2-inch-diameter shaft furnace. A maximum of 69 percent of the nickel and 76 percent of the cobalt were recovered from one sample of Puerto Rican laterite, and a maximum of 96 percent of the nickel and 91 percent of the cobalt were recovered from the Philippine laterite.

Jan 1, 1965

By R. J. Leary

Oxidation testing of copper-clad steel strip was performed in a muffle furnace to determine whether copper in contact with steel scrap could be removed by oxidation in an airstream at high temperatures. Substantially all of the copper was oxidized before any significant iron oxidation occurred. The rate of copper oxidation was not affected by contact with iron. Copper oxide scale separated spontaneously from the underlying metal during cooling. Results indicate the possibility of removing light-gage copper coatings and components from ferrous scrap by oxidation in an incineration process.

Jan 1, 1965

By Jack I. Paige

The devitrification of lithium silicate glasses was studied to determine the effect of annealing temperature, composition, and additives on nucleation and crystallization. High-purity glasses, prepared from reagent-grade chemicals, had close to optical quality when prepared by a vacuum induction melting method developed during this research, The progress of devitrification was traced by differential thermal analysis and thermal expansion for those lithium metasilicate-silica compositions containing 80 to 90 percent silica. Microscopic studies of glasses partially devitrified at various temperatures and annealing times indicated that the primary initial mode of formation of individual crystals ,vas from densely crystalline zones that filled in as crystallization advanced Of the additives tested, calcium, potassium, and sodium helped promote devitrification with the least cracking or surface deformation. Tin oxide was most effective in reducing volume contrast ion during devitrification, but was not ClS effective in preventing cracking as calcium or potassium additions.

Jan 1, 1965

By Joseph A. Cavallaro

This report describes the timed release analysis technique that was developed to serve as a tool for assessing the froth flotation cleaning potentials of fine-size coals. Using this developed technique, 16 coals from 10 different coalbeds were tested. All of the coals included in this study were quite amenable to froth flotation with float coal yields ranging from 80.7 to 99.5 percentage points. Float-and-sink analyses of the coals tested are shown to be of limited value in predicting froth flotation cleaning potential. Generally the float-and-sink analyses indicated a better product could be obtained than froth flotation could provide; although, in four of the coals tested froth flotation results were superior to those expected from the gravimetric analysis. The fixed carbon content of the samples collected was found to correlate with the floatability of the coals. The higher rank coals were the most readily floatable coals while the lower rank coals did not respond quite as well to flotation.

Jan 1, 1965

By J. M. Kuchta

Experimental data are presented on the autoignition temperature (AIT) characteristics of the hydrocarbon jet fuel, JP-6, in various oxygen-nitrogen atmospheres under conditions of constant volume and constant pressure. AIT's of this fuel in air varied little with fuel injection pressure but increased greatly with decreasing fuel content at low fuel-air-ratios. They also increased with decreasing oxygen content of the fuel vapor-oxidant atmosphere. Consistent with thermal ignition theory, the ignition temperatures increased with decreasing initial pressure, ignition delay, and vessel radius; expressions are given which define the observed variation of AIT with these variables for JP-6 fuel vapor-air mixtures. The significance of autoignition temperature data obtained using various ignition criteria is discussed to show the usefulness of such data in evaluating fire and explosion hazards. In addition, data are presented on the extent of oxidation that occurs prior to autoignition of this fuel in air at various temperatures.

Jan 1, 1965

By C. O. Hawk

Distillable oils derived from coal were desulfurized and hydrogenated at 2,500 psig in a two-step vapor-phase catalytic operation to give a product rich in saturated cyclic hydrocarbons. The first step was mainly a desulfurization at 400 C, the second a saturation at 300 C. One of the oils used as feed stock was from low-temperature carbonization of a bituminous coal, the other was from the liquid-phase hydrogenation of coal in the Bureau's pilot plant. The product from the saturation step was distilled to remove the light ends and high-boiling residue and to recover a fraction having acceptable properties with respect to heating value, density, freezing point, viscosity, and boiling range according to specifications suggested by the Air Force for ultra-high-speed aircraft fuel. Quantities of the fuel fraction available were too small for the thermal stability test approved by the Air Force. The experiments, performed on laboratory scale, comprised mostly a study of the effect of varying the oil feed rate (at constant oil-to-hydrogen ratio) on the yield of the desired fuel fraction. The yield of the fuel fraction made from low-temperature carbonization oil was a little more than 1 percent of the weight of coal carbonized; that from coal-hydrogenation oil was about 12 percent of the weight of coal hydrogenated. A few attempts to do both desulfurization and saturation in one operation with sulfur resistant catalysts, developed for vapor-phase hydrogenation or hydroforming, were unsuccessful. By leaving the low-boiling ends in both feed stocks to desulfurization, another product was obtained: a low-sulfur aromatic cut boiling below 200 C. This material would be suitable as a solvent or a chemical raw material.

Jan 1, 1965