Search Documents

By Oscar Weiss

An aerial magnetometer survey was carried out by the author's geophysical organization over the Vrede-fort dome, where Witwatersrand beds are wrapped around a granite plug 25 to 30 miles in diameter. The well-known magnetic shales of the Lower Witwatersrand system (to be referred to as LWW) give strong negative anomalies over the out-cropping portion of the dome. This is unusual as these same shales cause positive anomalies over large areas near Johannesburg and along a strike of 130 miles between the East Rand and Klerksdorp. It is suggested that the negative polarization is caused by heat and stresses connected with the doming. This negative polarization of sedimentary beds, which usually cause positive anomalies, is a good example of how "magnetic lows" can be caused by "structural highs." Significant magnetic anomalies should be tested by gravity and seismic methods irrespective of the sign of the anomalies. South of the line X — Y (see Fig 2 and 5) the gravity anomalies are smaller over the LWW beds and magnetic anomalies suddenly become weaker and even change signs by becoming positive. This peculiar phe- nomenon is explained by faulting which truncated the nearly vertical LWW shales at depth. In this manner the mass of the LWW beds has been reduced together with the weakening of the negative magnetic anomalies by positive poles which occupy the truncated end. Furthermore, by uplifting the beds between f1 and f2 (Fig 2) positive polarization becomes predominant, thus causing positive magnetic anomalies. General The Vredefort dome is one of the internationally known geological structures, which, among others, has attracted the attention of numerous American geologists. It was for this latter reason that our aerial magnetic results over this structure were selected by us for publication in the United States of America. A full description of the exposed geology has been published by Nell and readers are referred to this paper, which is subject to only slight modifications inasmuch as the subdivision of the Witwatersrand system (to be referred to as WW system) is concerned. The Vredefort dome is about 60 miles southwest of Johannesburg. The WW system, after being exposed in the vicinity of Johannesburg, plunges with southerly dips beneath the Vent-ersdorp and Transvaal systems. Along a section southwest from Johannesburg, as shown diagrammatically in Fig 4, we see no outcrops of the WW system until the Vredefort dome, where the Upper and Lower WW system are wrapped around an almost circular arc of a granite mass. Here the whole WW system is overturned around the perimeter of a huge granite plug 25 to 30 miles in diameter. Less than half of the circumference of this dome is exposed; the rest is covered by Karroo dolerites and sediments. The determination of the exact shape of the concealed part of the dome has been a matter of considerable interest and obviously geophysical methods were eminently suited for obtaining this information. A good start was made with a gravimeter survey carried out by the Geological Survey of the Union of South Africa.2 Our own

Jan 1, 1950

By S. H. Ward

Since the advent of the first airborne electromagnetic system, it has been evident that such systems were inherently limited to shallow depths of exploration of the orderof 100 to 200 feet. Hence in 1948 the author and his associates commenced a study of the feasibility of applying natural audio frequency magnetic fields to investigation of the electrical properties of the subsurface in order to provide a system capable of overcoming this limitation. This research culminated, in the summer of 1958, in the development of a new airborne prospecting device — AFMAG. This device has detected surface massive sulphide bodies while flown at heights as great as 3000 feet. Hence, by inference, it is deduced that it could find similar sulphide bodies if they were buried 2500 feet below surface and the aircraft flown at 500 feet. Thus a considerable improvement over conventional airborne electro-magnetic systems is obtainable with AFMAG. Airborne exploration in mountainous terrain involving deep valley fill now becomes possible. Examples are presented of the results of actual airborne AFMAG test surveys over known deposits of massive sulphide mineralization. Interpretation of the data is discussed with particular reference to the knowledge of size, dip, depth, depth extent, and conductivity of causative bodies as deduced from the flight records. The possibility of mapping major geologic structures, for both mining and oil exploration purposes, is discussed with the aid of examples of airborne AFMAG data. INTRODUCTION Electrical prospecting with natural audio frequency electromagnetic waves as a source has, within the last three years, become a practical reality. Both airborne and ground survey instruments under the trademark "AFMAG" (for audio frequency magnetics) have been used successfully in the search for conductive mineral deposits. It is the object of this paper to discuss the principles of airborne AFMAG and to illustrate its application by means of examples obtained over known geological situations. WHY AFMAG? In view of the large number of good airborne electromagnetic systems available for purchase or contract surveying, one may well ask, "Why another new system?". Primarily the answer lies in the fact that AFMAG does not suffer from the very limited depth of exploration available with, and inherent in, any conventional airborne electromagnetic system. AFMAG is not conventional insofar as an artificial transmitter is not required. Only a receiving and detecting device is employed. The electromagnetic fields measured are those from millions of electrical discharges in the atmosphere (e.g;..- lightning strokes). Their random distribution in time and space make these fields difficult to employ and it is only with recent advances in the electronics of geophysical instrumentation that this has become possible. A second reason for AFMAG and one of its

Jan 1, 1961

By H. T. Lundberg, J. H. Ratcliffe

In airborne gravity surveys effects of acceleration and irregular movements of the aircraft must be balanced out or overcome. The gradient of vertical gravity is recorded, therefore, by using two masses instead of one. As the amplitude variations are infinitesimal and difficult to measure accurately, at present it is enough to determine whether variation of gradient during flight is positive or negative. The positive portions of the pattern can then be indicated and contoured. Even with these simplifications, the source of energy must be exceptionally stable. General Principles: In the conventional gravi-meter the weight of a standard mass is determined at a number of selected points within the survey area. In most systems weight is determined by comparing the gravity pull with extension or torque

Jan 1, 1960

By R. R. Hartman, W. B. Agocs

IN the course of a return flight from Olympia, Wash., to Laramie, Wyo., an airborne magnetometer profile was recorded continuously. The level of flight was controlled at barometric levels along segments of the flight. Barometric altitude was changed from 3000 ft to a maximum of 12,000 ft above mean sea level to take care of topographic variations. Terrain clearance varied from 800 to 7300 ft. Horizontal positions were obtained by recording and tying to cities, towns, airports, river crossings, and other landmarks in the course of the flight. Figs. 1-6 show the course of the flight and the general geologic and tectonic features traversed. The flight line begins south of Olympia, Wash., and proceeds south across the Puget-Willemette depression to the Columbia River. Thence it proceeds eastward along the Washington-Oregon border across the Cascade Mts. and lava flows and the Umatilla basin to Pendleton, Ore. From Pendleton it traverses the Blue Mts. uplift of Oregon in a southeasterly direction, and then to the Boise basin of southwestern Idaho. The flight line swings in an easterly direction as it passes over the Snake River downwarp to the south of the Idaho batholith. It then passes over the northern portion of the Great Basin and the heavily overthrust area at the intersection of the Utah, Idaho, and Wyoming borders. The flight then assumes an easterly course to cross the series of basins and uplifts of southern Wyoming and terminates near the western flank of the Laramie uplift. It should be clearly understood that all statements in this article pertaining to the magnetics were interpreted on the assumption of elongate anomalies transverse to a single profile. Hence any theories or ideas advanced here are in line with future paths of research rather than trying to prove or disprove existing data. Magnetic Interpretation: Depth determinations were made by the slope method of Peters: which is stated as follows: "Draw a line in the maximum slope (at the point of inflection); draw a line whose slope is one-half this maximum slope; draw two lines parallel to this line tangent to the anomaly curve. The horizontal distance between the points of tangency is approximately equal to 1.6 times the depth [or the distance times 0.6251." Certain assumptions must be made for determinations of the causes of the magnetic anomalies:' 1) The anomaly is caused by a susceptibility change rather than basement relief. 2) Polarization of the basement rocks is in the same direction as the earth's inducing field. 3) The disturbing magnetic mass has a great horizontal length in comparison to its width and its sides are vertical and of great vertical extent. 4) The anomaly is unique and not affected by the anomalies from nearby sources.

Jan 1, 1957

By C. G. Cheriton

The Bathurst mining district is located near the town of Bathurst on the north shore of the province of New Brunswick in eastern Canada. This region is the northeasterly extension of the Appalachian mountain system. The area is heavily forested and covered with a fairly uniform layer of glacial gravels and boulder clay. The relief is low, increasing to a few hundred feet in the north west and several hundred feet in the extreme southwest. Thus, rock outcrops are scarce and occur mostly along streams and ridges. These factors made conventional prospecting difficult and resulted in the district becoming an excellent place for the application of regional geological studies, air photo techniques, airborne and gound geophysical methods and soil sampling. Late in 1952, The Brunswick Mining and Smelting Company discovered a very large base metal sulphide body presently known as their No. 6 orebody. Early in 1953, another and even larger sulphide body was discovered and is known as the No. 12 ore body. Mining exploration was very active thoughout 1953 and in 1954, The American Metal Company discovered the orebodies which have been developed into The Heath Steele 'Mines. The location of these deposits is shown on figure one. In the latter part of 1954, The Anaconda Company became interested in the district and decided to make a geological study of this new and promising base rrietal area. The following paper presents the story of the application of modern geological and geophysical techniques, leading to the discovery of a large sul-nhidp liodv. The Bathurst district is generally underlain by the Tetagouche group of Middle Ordovician rocks.

Jan 1, 1961

By D. G. Brubaker

IN the history of geophysical exploration by the electromagnetic method many procedures and types of equipment have been used. Source arrangements for surveying on the ground have included long wires grounded at both ends, large loops laid on the ground, small horizontal loops, and vertical loops of moderate to small sizes. Receivers have ranged from simple direction-finding coils to combinations of coils and a bridge circuit to measure quantities related to both amplitude and phase of the received signal. Primary considerations in choosing a survey method are effectiveness, speed, and economy. In work on the ground in which locating and outlining conducting bodies is the objective, methods using a vertical coil and a simple direction-finder have been found the most satisfactory. Mason1 and his associates applied such a method by setting up a vertical source loop, fed with low frequency alternating current by an engine-generator set. With a direction-finding receiver they surveyed lines along the ground in the plane of the loop, taking measurements at each station of the azimuth and inclination of the magnetic field direction. Deviations of this direction from the normal direction, that is, from horizontal and perpendicular to the traverse line, indicated a conducting body. Recent advances in design of light-weight generating equipment have encouraged using this and similar methods. In 1950 W. H. Westphal and the present writer developed a variation of this method and the apparatus for carrying it out. Their ideas were also based on experience with the Boliden Mining Co. method, which uses a small source coil and a vac- uum tube oscillator. The new procedure uses a small vertical source coil, powered by a vacuum tube oscillator, apd a direction-finding receiving coil. Source and receiver are kept a fixed distance apart and move as a unit along the survey lines. At each receiver station only the inclination of the magnetic field created by the source is measured. Source Unit: The source coil and a small vacuum tube oscillator together weigh about 45 lb. The source coil consists of about 60 turns of 10-gage

Jan 1, 1958

By Helen L. Cannon

BOTANICAL methods of prospecting for metalliferous ores are based on the premise that deposits at depth may be reflected chemically in surface vegetation. For the past several years, on behalf of the Atomic Energy Commission, the U. S. Geological Survey has investigated on the Colorado Plateau the application of botanical methods to uranium prospecting. Results suggest that orebodies may be found under a considerable cover of barren sandstone through the absorption of uranium and associated trace elements by plants growing at the ground surface. Plant physiologists have demonstrated that uranium is a necessary nutrient for plant growth and therefore is present in all plants.' The amount present is small but measurable. The absorption of uranium by plants growing over ore deposits forms

Jan 1, 1955

By F. N. Ward, E. H. Bailey

Camp and sample-site methods useful for determining about 0.5 to 16 ppm of mercury in soils and rocks have been devised to complement the analytical methods already widely used in geochemical prospecting. In the camp-site procedure the sample solution is obtained by digesting the finely powdered sample with hot nine-molar sulfuric acid and bromine, the latter generated in place. The solution is buffered at a pH of 4 and the mercury is extracted into a relatively small volume of an organic solvent. Estimations are made by comparing the color of the mercuric dithizonate extracted from the sample with that extracted from a standard. In the sample-site method the mercury is volatilized as the iodide and the latter is dissolved in a buffer solution from which the mercury dithizonate is extracted as in the camp-site method. The estimation is made by a similar comparison with standards or by comparing the color of the mercuric dithizonate with artificial standards prepared from Orange II, an azo dye. Except for the establishment of standards, the time required by an experienced analyst seldom exceeds 10 min for a camp-site determination and 5 min for a sample-site determination. Camp-site determinations are useful for commodity studies and intensive exploration programs; sample-site determinations are applicable to extensive and reconnaissance-type geochemical prospecting programs. The results obtained on samples taken along traverses above known mercury ore deposits in the California Coast Range and western Nevada demonstrate the usefulness of both methods in geochemical prospecting. The increasing use of the mercury content of soils, rocks, plants, or water in geochemical prospecting emphasizes the need for analytical methods which are sensitive and at the same time require a minimum of readily available equipment. Sensitive methods based on the absorption of ultraviolet light by mercury vapor are common in the literature31 12. Although none of these methods have been used to analyze the large number of samples required in geochemical prospecting, they could be extremely useful except for the expensive instrumentation usually required to make the methods quantitative Also, such methods are perhaps too sensitive for field use, especially around areas of possible contamination. Other methods involve the distillation of mercury from a relatively large sample and subsequent collection of the vapors in nitric acid6. The mercury is then estimated by titration with a suitable reagent such as thiocyanate. These methods are not trace methods because the actual amount of mercury measured is often as great as 50 to 100 milligrams. Also, such methods are unsuitable for geochemical prospecting because of the amount of equipment necessary and the time required. Still other methods involve colorimetry, and the sensitive reaction between dithizone and mercury (11).. is the basis for a number of reports on the determination of mercury in biological materials 5,7. Moreover, by the judicious use of solvent extraction and suitable complexing agents, the dithiaone method can be made almost specific for mercury. However, none of the dithizone methods have yet been applied to the determination of mercury in soils and rocks. In most colorimetric methods he sample solution

Jan 1, 1961

By S. H. Ward, R. A. Barker

THE Juniper Prospect is in Carleton County, N. B., at approximately 46" 31' north latitude, 67" 20' west longitude. During the summer of 1955 an area in west-central New Brunswick was selected for aerial electromagnetic prospecting with American Metal Co.'s helicopter-mounted equipment. Generalized, small-scale government geologic maps had suggested that this area was located along the western border of the northeast-trending granitic backbone of northwestern New Brunswick and might be underlain by the Ordovician-Silurian sediments and volcanics that are the host rocks for the recently discovered sul-fide deposits of the Bathurst-Newcastle district. The helicopter electromagnetic equipment located an anomalous conductive area, coincident with a small aeromagnetic closure, about five miles west of the town of Juniper. Subsequently 30 mining claims (total area about 6600 x 8000 ft) were staked and company personnel conducted geological, geophysical, and geochemical investigations on the property. The claims and immediately contiguous areas were mapped geologically, and an area of about 2000 x 4000 ft was soil-sampled and also surveyed by ground electromagnetic and gravity methods. Finally six diamond drillholes, totaling 3500 ft in length, were drilled to test the anomalous conditions discovered by the several exploration techniques used. The discovery of base metal sulfides during drilling was a technical success for the exploration methods, but the quantity of sulfides was too small to be profitably exploited.

Jan 1, 1959

By R. H. Pemberton

The principle of airborne electroniagnetic prospecting is well-known. 'The basic geonhysicai texts in inost cases discuss the main elements involved in electromagnetic prospecting. However. there is ceriainlv iittle information available to the public concerning he present types of airborne eiectromagnerlc systenis being flown today by both contracting companies and some of the mining companies which have their own instruments. This is unfortunate since it is difficuit for those people not conducting such operations to understand thoroughly the iarge variation in the electromagnetic instrunlents available. Basically, the aeriai electromagnetic induction method utilizes a primary or transmitting coil through which is generated an alternating magnetic field at a frequents: generally of the range of 100 to 2000 cycies per sec. This primary field links with buried conductors and generates eddy currents within them. These eddy currents in themselves generate a secondary magnetic field of the same frequencv, but generally nut-of-phase with respect to the prinlarv field. This secondarv field is detected above the ground in the pick-up or receiver coil which is tuned to the frequency of the current applied to the primary transmitter coil. One of the main problems in the development of an airborne electromagnetic system is that of maintaining constant coupling between the cransmitting and receiving coil systems. Any variations in the coupling due to relative motion between the two coils will result in an in-phase signal being induced in the receiver coil. [However, any variation in the coupling does not result in an out-of-phase signal change in the receiver coil. The first airborne eiectromagnetic svsteins which were developed utilized a large prlniarv coil set up on the aircraft with the receiving coil being towed behind in a bird, generally at the end of a cable of about 500 ft. in length. It is possible with such a system to record the out-of-phase or quadrature responses more readily than the in-phase re-sponse. One system utilizes a dual frequency method, wnereby the out-of-phase responses at two frequencies are recorded. Another system used today records a single-frequency olrt-of-phase response. Recentlv home companies have succeeded in measuring from ne air both the out-of-phase and the in-phase components. The usefulness of recording in-phase is weil-known, but unfortunately this is difficult to obtain in any towed-bird system. In order to measure the true in-phase signal, the most straightforward system is that in which both the transmitter and receiver coils .Ire affixed in space so that there is little or no relarive motion between the two coils. THE FLIGHT SYSTEM The particular system which Canadian Aero Service is using at present is mounted on a Sikorsky S-55 helicopter (Fig. 1). A record of both the in-phase and out-of-phase responses is made at a frequency of 390 cycles per sec. The transmitter coil is set on a boom mounted in the front of the helicopter; the receiver is set on a tail boom extending back from the helicopter. Separation between these coils is about 65 ft. The two coils are mounted in a vertical co-axial relationship. Having the transmitting coil in a vertical plane ensures that maximurn coupling will occur with vertical conductors rather than flat-lying conductors. Having them mounted as they are in a co-axial relationship on the helicopter ensures that maximum response will occur when the flight direction is orthogonal to the strike direction of a given conductor. The present sensitivity of the Em system is 20

Jan 1, 1961

By Oscar Weiss

STILFONTEIN and surrounding areas gave nega-tive results in all prospecting attempts since about 1904 when Goerz and Co., a forerunner of Union Corporation Ltd., first drilled in the region and on the farm Stilfontein. Subsequent efforts by African and European Investments Co. and Anglo American Corp. from 1934-37 were completely unsuccessful. Holes drilled by these companies on the farms Riet-fontein, Hessie, and Palmietfontein were stopped in the Lower Witwatersrand system without finding payable reefs. The results of gravimeter, ground magnetometer, and aerial magnetometer surveys are presented in the area, in and around the new Stilfontein Gold Mine, in the Klerksdorp District of the Transvaal in the Union of South Africa. The gravimeter and ground magnetic surveys were completed in 1947—48. The gravity anomalies suggested a block of Upper Witwatersrand quartzites faulted-up between denser rocks of dolomite and Ventersdorp lava. Boreholes S.T. 1, 2, and 3 were drilled in 1948 and, after penetrating the dolomite and Ventersdorp lava, entered Upper Witwatersrand quartzites and intersected the Gold Estates Reef and Vaal Reef. Subsequent drilling delineated the suboutcrop of the Vaal Reef and determined the main structure of this horizon. The gold content of the Vaal Reef was highly payable and shaft sinking is now in progress. The Stilfontein Gold Mining Co. has been formed and, up to date, f5,000,000 capital has been raised for plant, shaft sinking, and development. The payable Vaal Reef horizon extends further south from Stilfontein, the reef occurring at increasing depths. It is possible that at least another mine may be established on these deeper horizons. The farm Stilfontein 39 is situated in the Klerksdorp District of the Transvaal. This farm and the surrounding areas have been subjected to repeated programs of prospecting dating back to about 1904, when Goerz and Co., the forerunner of Union Corporation, Ltd., first drilled on the farm and in the surrounding areas. From 1934-37, numerous boreholes were drilled on the neighboring farms, Riet-fontein. Hessie. and Palmietfontein, by African and European Investment Co. and Anglo American Corp. All these efforts were completely unsuccessful, and nobody suspected any possible gold-bearing area on Stilfontein until about 1947, when a gravity traverse run by B. D. Maree on the main road, showed a negative gravity anomaly. During 1947-48, the writer's organization completed gravimeter and magnetic surveys on Stilfontein and Rieffontein. An area of negative gravity anomalies was mapped, and it was suggested that this could be caused by blocks of Upper Witwatersrand quartzites, of the average density of 2.65, faulted up between dolomites and Ventersdorp lavas, the density of both of these rocks being 2.8. Fig. 1 shows the geology of the area as mapped by L. T. Nel of the Geological Survey of South Africa. The boreholes on Stilfontein, with the exception of a single hole of Goerz and Co., were drilled after the completion of the geophysical survey. The grouping of the first boreholes S.T. 1, 2, 3, 4, 5, and 6, clearly shows that these were located in the zone of negative gravity anomalies. Fig. 2 shows the gravity anomaly contours. Fig. 3 shows two sections across the gravity anomaly, together with the corresponding geological sections as obtained from boreholes. The close relation between gravity values and thickness of dolomite plus Ventersdorp lavas is striking. The two latter formations having the same density (2.8), act as one mass as far as gravity effects are concerned. Fig. 4 shows the magnetic anomalies observed on the ground by vertical magnetometers and at 500 ft abbve mean ground level by aerial magnetometer. The latter are anomalies of the total magnetic intensity. The magnetic results show that, on the farm Rietfontein and on the northern half of Stilfontein. Lower Witwatersrand magnetic shales were to be expected at relatively shallow depths. As the strongly

Jan 1, 1952

By T. M. Allen, W. H. White

THE Greenwood-Grand Forks area of southern central British Columbia, known as the Boundary District, has a long history of mining exploration and production. At the turn of the century this was the premier copper mining camp in the British Empire, its total production amounting to some 20 million tons. Most of this ore came from the great Granby mines at Phoenix, but the Motherlode mine at Deadwood camp, 6 miles to the west, and several mines in Summit camp, 5 miles north of Phoenix, made important contributions. The large deposits were exhausted in 1918 and the district since has seen only desultory exploration and salvage operations. The orebodies are mineralized skarn zones in limestone members of a thick series of Upper Paleozoic sedimentary and volcanic strata. Chalcopyrite is the primary ore-mineral. Copper carbonates and silicates occur sparingly in outcrops, but the oxidized zone generally is very shallow. Much of the surface is mantled by glacial drift which in most places ranges in thickness from 2 to 15 ft. In some of the hanging valleys, however, the glacial drift may be as much as 100 ft thick and may assume drumlin-like forms. In 1951 an ambitious program aimed at the discovery of new orebodies and important extensions of abandoned deposits was launched by Attwood Copper Mines, Ltd. In this district so thoroughly searched by an earlier generation of prospectors, any orebody which had remained undiscovered must have little or no surface indication. Consequently, in addition to the basic detailed geological work, the program of exploration included magnetometer and self-potential surveys. Geological bets and geophysical anomalies were tested further, prior to diamond drilling, by a study of copper distribution in tree twigs and/or in the soil. The soil sampling and analytical methods used and some of the results seem of sufficient importance to warrant this paper. The authors had done some plant sampling in this and other districts, using the dithizone neutral-color-end-point method (Warren and Delavault, 1948, 1949; White, 1950),1-3 but they were unfamiliar with its soil application. Finally, after much experimenting in the field, they adopted the methods described here. These methods are not entirely original or defensible on theoretical grounds, but under field conditions of rapid sampling and analysis the results are reliable enough to be of use. Fig. 1, which shows the results of duplicate analyses of duplicate soil samples taken at 50-ft intervals across an anomalous zone, indicates the relative dependability both of the sampling and analytical methods. Sampling and Analytical Equipment A 2-ft piece of 1-in. solid drill steel, one end sharpened to a broad, conical point. The steel is marked at 1 ft from the point. A 2-ft piece of ½-in. black iron pipe, one end filed to a bevelled cutting edge. The pipe is marked at 1 ft 3 in. from the cutting end. A 3-lb hammer. A plastic or rubberized sheet about 18 in. square. Moisture-proof assay pulp envelopes. A 10-mesh seive made from window screen with the paint burnt off. A small assay spatula. A pan balance sensitive to 10 mg. Two ignition trays about 4 in. square, made of sheet iron turned up along the edges. A Coleman two-burner gasoline stove. An asbestos board about 5x8 in., used as a hot plate on the gasoline stove. A circular aluminum rack to hold 8 test tubes while refluxing (design of Almond and Morris). Pyrex Glassware Large refluxing test tubes, 25x200 mm, marked at 40 ml volume. Breakers, 20 ml. Pipettes, 1, 5, and 10-ml capacity. Graduate, 50 ml. Shaking cylinders, 100 ml, glass stoppers. Burette, 25 or 50-ml capacity, with holder. Chemical Supplies 1 N sulphuric acid. Hydroxylamine hydrochloride, solid crystals. Fisher Alkacid test paper. Copper standard solution. Dithizone standard solution 60 mg per liter. Water reasonably free of metals. Soil Sampling Method: The problem of how to take a soil sample is extremely crucial. The method outlined below, adopted after a number of tests, has the advantages of uniform pattern, uniform depth, and uniform size of sample. The area to be tested was marked off by chain and compass lines 100 ft apart, normal to the strike of possible ore deposits. Numbered stakes were set at 50-ft intervals along these lines and a soil sample was taken at each stake in the following manner. The drill steel was driven into the ground normal to the slope of the surface to the marked depth of 1 ft, moved slightly from side to side, then carefully withdrawn. The iron pipe was inserted to the bottom of this hole, tapped down to the marked depth of 1 ft 3 in. and withdrawn; the 3-in. soil plug in the

Jan 1, 1955

By Harold M. Mooney

RESISTIVITY measurements for determining depth to bedrock, water table, and other geologic discontinuities have had only limited success. Many of the difficulties can be attributed to complex geology and to basic limitations of the method; current flow through a continuous medium is a diffusion phenomenon, emphasizing irregularities near the source and smoothing out those at a distance. Some of the failures, however, are due to careless field work and incompetent interpretation. A forthcoming publication1 may help to reduce difficulties of this sort. The writer here attempts to bring order into the multiplicity of interpretation methods and, to a limited extent, to evaluate them. For all methods, the field data to be interpreted consist of apparent resistivity values plotted against electrode separation, Fig. 1. The interpretation should give depths to one or more geologic horizons. Direct currents and the Wenner four-electrode configuration will be assumed, since these are widely used, although the interpretation problems remain essentially the same for other electrode configurations. Alternating currents higher than, say, 20 cycles per second introduce complications beyond the scope of this paper. Three approaches to the interpretation problem have been used. These may be called empirical, theoretical curve matching, and direct. Many techniques have been proposed, but each can be reduced to one of these approaches and to a single geologic idealization. This idealization rests on the following assumption: the earth in the limited volume of interest can be approximated by a horizontal sequence of layers, each homogeneous and isotropic in its electrical properties. This seemingly restrictive assumption has proved to have practical value, although future work should aim at removing some

Jan 1, 1955

By F. Gordon Smith

ALTHOUGH several geological indicators of the critical type are known, including quartz inversions and decomposition of hydrous minerals such as serpentine, there are very few of the general type. Solid solutions are excepted, but the limitations of use are very restricted and interpretations are sometimes ambiguous. General methods for determining temperature and pressure conditions during the crystallization of minerals would have considerable scientific and economic value. It is not the purpose of this paper to discuss the various methods of geological thermometry and barometry, but to present one general method, applicable to all minerals, and to describe what progress has been made in the methods of measurement. The general method, in brief, is a study of the stress conditions in and around various types of foreign inclusions which are trapped in minerals during growth. The method depends upon the fact that any homogeneous gas, liquid, or solid will in general have coefficients of thermal expansion and volume compressibility different from those of any given mineral. Therefore stress must develop in and around all types of inclusions in minerals if the temperature or the pressure, or both, are changed from the conditions which prevailed during the growth of the mineral. The methods of measurement consist of determinations of the temperature-pressure conditions of fit of the inclusions in the host mineral. The types of inclusions in minerals are: I—gas, or liquid plus vapor, when observed at room temperature, due to crystallization under pneumatolytic conditions; 2—liquid, or liquid plus vapor when observed at room temperature, due to crystallization under hydrothermal conditions; 3—glassy solid, or devitrified glass, due to crystallization under magmatic or high temperature metamorphic conditions, in a siliceous liquid; and 4—crystals, due to overgrowth of other minerals crystallizing simultaneously or of other minerals which crystallized previously. A survey of the literature shows that much valuable earlier work on inclusions, especially that car- ried out in England in the last century, has dropped out of current knowledge. The following is a brief summary of the significant contributions to the problem up to the present day. Davy in 1822 asserted that fluid inclusions in minerals consist of an aqueous solution of salts and a gas bubble, the whole being either at lower or higher pressure than atmospheric.' At intervals from 1823 to 1862, Brewster contributed information concerning other types of inclusion consisting of 1—aqueous solution, a much more expansible liquid, and a gas; 2—aqueous solution, salt crystals, and a gas; and 3—the very expansible liquid and a gas. The very expansible liquid fills the gas space between 20" and 30°C. Compression strain effects were seen around inclusions in diamond, topaz, and other minerals.'-" Sorby in 1858 and 1869 further advanced the study begun by Davy, stating that fluid inclusions represent a sample of the mother liquor of crystallization and that the degree of filling of aqueous inclusions at room temperature defines the temperature-pressure relations during formation of the host. The degree of filling may be measured by determining the minimum temperature of filling of the inclusion by the liquid phase. The very expansible liquid in some fluid inclusions is liquid carbon dioxide. The temperature at which salt crystals in fluid inclusions completely dissolve in the fluid is the minimum temperature of formation. Inclusions of glass or devitrified glass indicate crystallization from a melt. Inclusions of crystals in minerals are often centers of strain, which may be seen by optical effects or by radial tension cracks. Sorby realized that an analysis of stress-strain relations about inclusions could be used to provide precise data on the temperature of crystallization, but the matter was never pursued.' , Hartley (1876, 1877),".'" Hawes (1881)," Wright (1881),'V ohnsen (1920),I3 and Holden (1925)"

Jan 1, 1953

By F. Gordon Smith

ALTHOUGH several geological indicators of the critical type are known, including quartz inversions and decomposition of hydrous minerals such as serpentine, there are very few of the general type. Solid solutions are excepted, but the limitations of use are very restricted and interpretations are sometimes ambiguous. General methods for determining temperature and pressure conditions during the crystallization of minerals would have considerable scientific and economic value. It is not the purpose of this paper to discuss the various methods of geological thermometry and barometry, but to present one general method, applicable to all minerals, and to describe what progress has been made in the methods of measurement. The general method, in brief, is a study of the stress conditions in and around various types of foreign inclusions which are trapped in minerals during growth. The method depends upon the fact that any homogeneous gas, liquid, or solid will in general have coefficients of thermal expansion and volume compressibility different from those of any given mineral. Therefore stress must develop in and around all types of inclusions in minerals if the temperature or the pressure, or both, are changed from the conditions which prevailed during the growth of the mineral. The methods of measurement consist of determinations of the temperature-pressure conditions of fit of the inclusions in the host mineral. The types of inclusions in minerals are: I—gas, or liquid plus vapor, when observed at room temperature, due to crystallization under pneumatolytic conditions; 2—liquid, or liquid plus vapor when observed at room temperature, due to crystallization under hydrothermal conditions; 3—glassy solid, or devitrified glass, due to crystallization under magmatic or high temperature metamorphic conditions, in a siliceous liquid; and 4—crystals, due to overgrowth of other minerals crystallizing simultaneously or of other minerals which crystallized previously. A survey of the literature shows that much valuable earlier work on inclusions, especially that car- ried out in England in the last century, has dropped out of current knowledge. The following is a brief summary of the significant contributions to the problem up to the present day. Davy in 1822 asserted that fluid inclusions in minerals consist of an aqueous solution of salts and a gas bubble, the whole being either at lower or higher pressure than atmospheric.' At intervals from 1823 to 1862, Brewster contributed information concerning other types of inclusion consisting of 1—aqueous solution, a much more expansible liquid, and a gas; 2—aqueous solution, salt crystals, and a gas; and 3—the very expansible liquid and a gas. The very expansible liquid fills the gas space between 20" and 30°C. Compression strain effects were seen around inclusions in diamond, topaz, and other minerals.'-" Sorby in 1858 and 1869 further advanced the study begun by Davy, stating that fluid inclusions represent a sample of the mother liquor of crystallization and that the degree of filling of aqueous inclusions at room temperature defines the temperature-pressure relations during formation of the host. The degree of filling may be measured by determining the minimum temperature of filling of the inclusion by the liquid phase. The very expansible liquid in some fluid inclusions is liquid carbon dioxide. The temperature at which salt crystals in fluid inclusions completely dissolve in the fluid is the minimum temperature of formation. Inclusions of glass or devitrified glass indicate crystallization from a melt. Inclusions of crystals in minerals are often centers of strain, which may be seen by optical effects or by radial tension cracks. Sorby realized that an analysis of stress-strain relations about inclusions could be used to provide precise data on the temperature of crystallization, but the matter was never pursued.' , Hartley (1876, 1877),".'" Hawes (1881)," Wright (1881),'V ohnsen (1920),I3 and Holden (1925)"

Jan 1, 1953

By Otto W. Nuttli

THE magnetic method of prospecting is well suited to determination of faulting in the basement rock. In addition to establishing the horizontal position of the fault, it often furnishes valuable information concerning the depth and amount of faulting. Consider a simple case of a vertical fault, represented in cross-section in Fig. 1. Let A A' represent the plane of observation (ordinarily the surface of the earth), and BB'B"B"' the upper surface of the basement. Assume that the sedimentary rocks are nonmagnetic, so that the magnetic susceptibility of the material above the basement is zero. Let k indicate the susceptibility of the basement rock, c the density contrast between it and the neighboring sedimentary rocks, and the amount of vertical displacement. Fig. 1 shows the material, indicated by cross- hatching, which gives rise to the magnetic anomaly. In most cases it can be assumed that is small compared to the thickness of the sedimentary rocks. The semi-infinite, rectangular slab of rock of susceptibility k, density contrast , and thickness t may then be replaced by a semi-infinite sheet CC' of mass t per unit area at depth 2 (the mean depth of the slab). Nettleton 1 states that this approximation results in an error of less than 2 pct for the computed gravitational field intensity when t is as great as 2/2 and decreases rapidly for smaller values of t. By a theorem of Poisson, the magnetic field intensity can be determined readily from the gravitational field. The theorem states that W = (I/) • (U/i) i1 [1] where W is the magnetic potential associated with the structure, I is the intensity of magnetization which is assumed to have the direction of the inducing field, ? is the constant of gravitation, the density contrast, U the gravitational potential associated with the structure, i the direction of the inducing magnetic field, and i1 a unit vector in that direction. The multiplication indicated in Eq. 1 is

Jan 1, 1956

By Merlyn B. Buhle

The value of the earth resistivity method in groundwater studies in Illinois has long been recognized. Owing to the sharp electrical contrasts between sand and gravel deposits and glacial till, alluvial silt or underlying shale, much of the earth resistivity prospecting has been of a relatively elementary nature and has been highly successful. Approximately 90 pct of earth resistivity interpretations by the State Geological Survey have been accurate for practical purposes. Four studies involving fairly simple geologic situations are presented in this paper as typical cases. FOR the past 20 years electrical earth resistivity exploration has been used in Illinois in many phases of study undertaken by the State Geological Survey, chiefly in locating and outlining deposits of water-bearing sand and gravel from which to obtain ground water for municipal and industrial supplies. At least 43 municipalities in the state derive their total water supply from deposits of sand and gravel discovered by resistivity methods. These deposits occur in both Quaternary and preglacial valleys and within much of the glacial drift which covers a large portion of the state. In recent years there has been much demand from rapidly growing municipalities for help from the Illinois Geological Survey to extend existing well fields. Water supplies for many and varied industries constitute a considerable portion of the Survey's studies. The diminishing need of water supplies for railroads has 'been accompanied by an increasing demand by the oil industry for water for secondary recovery programs. The instruments used by the Illinois Geological Survey follow closely the commutated direct current circuits developed by O. H. Gish and W. J. Rooney' using the Wenner2 electrode configuration. More recently replacement of the hand-driven commutator by a synchronous vibrator has led to increased ease of operation and accuracy. Continuing improvement of equipment and technique has led to many changes in the instruments, but the operating theory remains the same. In the field operation at a selected station, four electrodes are set at equal distances in the ground 6 to 10 in. deep, in a straight line. A 16 to 20-cycle current is applied to the two outside steel electrodes

Jan 1, 1954

By Harold M. Mooney

WHEN apparent resistivity data are taken with the symmetrical Wenner 4-electrode spread, a fixed center position is used and readings are taken for values of electrode separation. Basic data consist of apparent resistivity plotted against separation of adjacent electrodes . The interpreter attempts to infer geologic structure, such as the depth to discontinuities and the nature of subsurface earth materials. An earlier paper' described methods for interpreting resistivity data. All of these involve a severe assumption, namely that the earth in the region of interest consists of horizontal layers, electrically homogeneous and isotropic. The actual earth never satisfies this assumption exactly and may deviate from it so much that none of the above methods can be applied. Attempts in three directions have been made to modify the assumption so that it approaches known geologic complexity more closely. First, curves have been calculated for dipping discontinuities. Stern' and Aldredge hose a few widely separated dip angles. Trudu confined his attention to small dips. Berel'kovskiy and Zubanov computed gradient curves for widely separated dip angles. Unz as given the most complete solution, with a brief attempt to treat the three-layer case. Second, anisotropy can be taken into account. It seems geologically probable that layered materials have different vertical and horizontal conductivities. Cagniard, Maillet, and Pirson et up methods for finding an equivalent hypothetical isotropic medium. Standard interpretation methods can be applied to this, and the actual medium can then be deduced. Belluigi'" discounts the practical importance of anisotropy; Geneslay and Rouget do not agree with his conclusion. Third, the effect of variable resistivity in a layer can be considered. Keck and Colby" examine the mathematics of an exponential increase in a surface layer. Several authors, for example, Stevenson,'' consider a continuous variation of resistivity with depth. The present paper deals with a linear variation of resistivity in a surface layer. Geologically, surface variations should be expected. Unconsolidated materials such as glacial drift show marked irregularities over short distances. The effects of weathering change with depth. The moisture content of material above the water table may vary from a dry sand to a saturated clay, and both of these will be changed by rainfall. Figs. 1 to 6 present apparent resistivity curves to show the effect of a variable surface layer. In all cases resistivity varies linearly with depth down to a depth of one unit. Material beneath this depth has constant resistivity. Electrode separation is plotted in depth units. Insets on each figure show the corresponding cross-sections, plotting true resistivity against depth. To illustrate, consider curve A of Fig. 1. The true resistivity of material at the surface of the earth is taken as 0.4 units. Resistivity increases with depth, reaching a value of 1.0 at 0.5 depth units and 1.6 at 1.0 depth units. Below a depth of 1.0, all the material has very low resistivity (zero, for purposes of calculation). Curve A in the main part of Fig. 1 shows how apparent resistivity varies for this case as the electrode spacing is increased. To illustrate further, curve E of Fig. 4 corresponds to true resistivity of 1.2 units at the surface, 1.0 at a depth of 0.5 units, 0.8 at a depth of 1.0, and 1.5 for all depths greater than 1.0. Apparent resistivity curves have been plotted logarithmically so that the shape of the curves becomes independent of the units, giving the curves wide validity. A certain drift-covered area, for example, shows a gradual decrease of resistivity from 230 ohm-meters at the surface to 150 ohm-meters at the bedrock surface, 275 ft down; bedrock resistivity is 800 ohm-meters. Curve E of Fig. 5 indicates that true resistivity decreases from 1.2 units at the surface to 0.8 at a depth of 1.0, then increases abruptly to a constant value of 4.0 units. Since resistivity and depth ratios are the same, this can be used to predict the field curve. For Fig. 5, multiply true resistivity and apparent resistivity by

Jan 1, 1955

By Robert G. Van Nostrand, John H. Henkel

TRANSIENT potentials obtained in resistivity prospecting can be separated into two classes. The first is electromagnetic, has a comparatively short time constant, and increases in relative amplitude as the electrode separation is increased. These electromagnetic transient potentials, of which an excellent theoretical treatment is given by Yost: are the result of changes in the current and can be classed as differentiated signals. The second class is electrochemical, has a comparatively long time constant, and decreases in relative amplitude as the electrode separation is increased. The electrochemical signals are generated by the current flow itself and can be classed as integrated signals. The transient potentials due to electrochemical factors are the subject of this article. The phenomenon is referred to as induced polarization. Schlumberger" was the first worker to observe induced polarization, but he was unsuccessful in attempts to apply the principles of induced polarization in electrochemical prospecting. Other workers, notably Bleil; have studied polarization and in some cases pointed out its possibilities, but no theory has been presented that describes polarization and its time dependence adequately. It is the purpose of this discussion to present the essence of a theory to geo-physicists and to show that it leads to results consistent with experimental evidence. The theory on which this analysis is based has existed in electrochemical circles since 1910."

Jan 1, 1958

By F. C. Canney

Geochemical prospecting seeks hidden mineral deposits by sampling for variations in the chemical composition of naturally occurring materials. Usually the samples are of soils and other products of weathering and erosion—surface materials extremely susceptible to contamination by human activities. Except when a survey is conducted well away from populated areas, contamination is an ever-present hazard. The program's success is particularly endangered when the contaminants are the elements sought; if these occur erratically throughout an area, spurious anomalies completely unrelated to mineralized areas can be formed. Evenly distributed contamination can be dangerous too, if it raises the background to such a level that true anomalies can no longer be easily detected. Suppose, for example, that in an area where the lead background is 20 parts per million the soil over a lead vein contains 1000 ppm of lead. Here the contrast would be 50 to 1, which is very satisfactory for geochemical surveying. Now if 1000 ppm of lead from some source were added evenly to the soil in this area, the contrast would be reduced to about 2 to 1, and the anomaly would no longer be readily detectable because a threshold of significance twice the value of the background is the minimum generally used for interpreting geochemical data. Of the many possible sources of contamination, probably most important are smelter fumes, which may distribute large quantities of metal contaminants over many square miles of ground. For several reasons, the investigation reported here was begun in the Coeur d'Alene district in northern Idaho: 1) a lead smelter has been operated in this district since 1917 and an electrolytic zinc plant since 1928, and presumably the contamination patterns are strongly developed; 2) to evaluate the usefulness of certain geochemical techniques, V. C. Kennedy and S. W. Hobbs of the USGS had already studied the distribution of copper, lead, and zinc in the soils (both in background areas and other veins) and in the water and plants, providing a criterion for measuring the magnitude and effect of soil contamination; 3) one of the economically important parts of the district lies south of the South Fork of Coeur d'Alene River and within a radius of five miles of the reduction plants near Smelterville (Fig. 1). In this area, and in the entire district, conventional methods of prospecting are hindered by heavy vegetation and thick soil cover, and the possibility of contamination by smelter fumes has discouraged geochemical prospecting. Should data reveal that geochemical prospecting could be done successfully in such an area, a particularly useful tool would be available to mining companies and prospectors searching for concealed orebodies in this economically important part of the district. The field work on which this report is based was done from July 28 to 31, 1955. It should be emphasized that this was reconnaissance study only, and therefore far from exhaustive. Previous Investigations in U. S. : The first geochemical survey known to have been affected by contamination was conducted in 1940—a geobotan-ical reconnaissance made in the Michigan copper district by a private company. Geologists found striking variations in the copper content of oak and maple leaves, but unfortunately the high copper isograds of the study seemed to be related more to the Calumet and Hecla copper smelter fall-out than to mineralized ground.' The leaves of one oak tree near the smelter contained 0.4 pct Cu. Similar contamination was reported by Clarke (Ref. 2, p. 41), who conducted experimental geochemical soil and botanical surveys at Ray, Ariz. He found that the leaves of oak trees growing in unmineralized ground near Superior, Ariz., contained more copper than the leaves of oak trees growing on the capping of the Ray orebody and attributed this fact to contamination from the fumes of the Magma smelter at Superior. According to H. E. Hawkes,3 soils and stream sediments in the Superior area are also severely contaminated. Hawkes' work there has shown a copper content averaging 0.5 pct in the surface horizons of soils within one mile of the smelter stack. Samples taken only a few inches below the anomalous surface samples showed only background copper values. In 1950 L. C. Huff' of the USGS made a geochemical survey in an area near Jerome, Ariz., and found considerable zinc and copper in the soils over unmineralized basalt close to Clarkedale, Ariz., and over limestone close to Jerome. As the amounts were notably greater than could reasonably be expected to be derived from the underlying rocks, Huff suspected airborne contamination from the smelter at Clarkedale. Description of Area: The area sampled in detail (Fig. 1) for the study presented here is one of strong relief. The dominant watercourse is the westward-flowing South Fork of the Coeur d'Alene River. East of Kellogg the South Fork flows in a rather narrow canyon, but its valley floor widens considerably to the west where much of the flood plain is covered by an extensive veneer of mining, milling, and smelting debris. South of the South Fork and between Big Creek and Pine Creek is a mountainous area where

Jan 1, 1960