Search Documents

By R. R. Hall

Tests were conducted to assess the potential of column flotation for beneficiation of a talc ore from Montana. This ere contained approximately 80% talc, with the gangue comprised mainly of chlorite, silica, and dolomite. A tributylamine, MIBC, and sodium silicate reagent suite proved effective for talc flotation. Rougher-cleaner column flotation in a continuous open-circuit produced a final talc concentrate which contained 0.90% Al2O3. 0.17% CaO, and 1.28% Fe2O3. These analyses represented impurity rejections of 77, 85, and 65%, respectively. Weight recovery for this open-circuit was 52%; however, weight recovery was estimated to be 75% with cleaner tailings recycle. Results from this investigation show that column flotation is a viable means for beneficiating talc.

Jan 1, 1990

By W. W. McClintock

A column flotation system was designed to conduct release analyses of a very finely disseminated, stratiform, copper ore from the Denali Copper Prospect, Alaska. Chalcopyrite is finely disseminated in a carbonate matrix and pyrite is disseminated in both the chalcopyrite and gangue, requiring grinding to 20 microns for adequate liberation. A 25 mm x 2.4 m glass flotation column was designed. The ore and its flotation tailings were repeatedly floated to obtain a rougher concentrate, which was repeatedly floated to produce release fractions. These were analyzed for copper, iron calcium and magnesium. Release curves were plotted. The procedure was replicated at each of two grinds; 99% and 88% passing 37 microns (400 mesh), and should find application for flotation characterization and process selection. Bond grindability work was also conducted.

Jan 1, 1994

By A. M. Al Taweel, V. K. Kasireddy

Intensive coal cleaning usually necessitates fine grinding of the feed in order to liberate inorganic constituents from the surrounding organic matrix. This however adversely affects the ability of flotation techniques to beneficiate coal. Such difficulties are mainly attributed to the increase of particle population density, the decrease in capture efficiency, and the greater tendency of inorganic components to report with the froth. A three-pronged approach was adopted in an attempt to overcome these difficulties. The aggregative flotation technique was used to reduce particle population densities and improve capture, while unconventional spargers were used to generate a wide range of bubble sizes. Use of unagitated flotation columns allowed for the maintenance of countercurrent flows in both the recovery and washing sections. The combined effect of these parameters enabled the recovery of 92% of the carbon content of coal having an average particle size of 20.5 µ m, while rejecting 85% of the ash. This was accomplished using 2 kg of fuel oil per tonne of coal in a column 2 meters high operating at 2-3 tph/m3, a capacity which compares favourably with conventional cells.

Jan 1, 1989

By James N. Orlich

Meridian Gold Company's Royal Mt. King mine (RMK), a subsidiary of FMC Gold Company, is located approximately 40 miles east of Stockton, California on the western edge of the historic mother lode belt. Gold ore at RMK is associated with a series of northwest trending fault zones hosted in either meta-volcanic or meta-sedimentary rock types commonly referred to as greenstone sulfide and carbonaceous phyllite. Mineralogy studies show gold in both ore types to occur primarily as electrum in the form of 1 -20 um inclusions in pyrite with varying amounts of free milling gold. In carbonaceous ores, gold was not found to be closely associated with carbon. At the start of the current mining operation, three major ore resources were identified. North Pit and Gold Knoll pits were the major greenstone reserves while Skyrocket Pit contained over 60% of the total reserves as carbonaceous ore. Since North Pit and Gold Knoll were to be the first areas mined, the mill began operation in February 1989 with a flowsheet designed for greenstone ores with a carbonaceous expansion anticipated after depletion of the greenstone reserves.

Jan 1, 1992

By Jr. Raleigh

In a cooperative agreement between the U.S. Bureau of Mines and the U.S. Department of Energy, laboratory column-flotation tests were conducted to evaluate fluorosurfactants as selective fine coal flotation collectors. A Middle Kittaning seam coal responded to flotation with both anionic and nonionic fluorosurfactants. These fluorosurfactants were no more selective than MIBC alone. However, for increasing coal yields, nonionic fluorosurfactant systems did not increase total sulfur and ash contents as sharply as MIBC systems. Flotation selectivity also improved slightly when a combined anionic fluorosurfactant-MIBC system was used in acidic pulps (pH < 3.6). While the fluorosurfactants examined will not likely have direct application in current coal flotation practice, other fluorosurfactant systems could eventually prove beneficial for floating fine coals.

Jan 1, 1990

"This research aims at improving the beneficiation of coals and minerals in fine and ultrafine size fractions. A widely used method for upgrading fine and ultrafine particles is froth flotation, which is generally classified into mechanical flotation and column flotation. The present work is focussed on column flotation. A flotation column equipped with a conventional bubble diffuser/sparger was used with oscillatory air supply generated using a fast-switching solenoid valve. The flotation tests were carried out for coal particles and mineral particles, respectively, and a comparison in flotation performance was made between oscillatory air supply and steady air supply. It was found that use of oscillatory air supply with a proper valve switching frequency and on/off time ratio to replace steady air supply could lead to increased recovery of coals or minerals by more than 14 percentage points and substantial reagent cost savings. The improved flotation performance was attributed to enhanced gas dispersion and flow conditions. This research offers a simple new approach to improving the beneficiation of fine coals and minerals with using flotation columns.INTRODUCTIONFroth flotation has been widely used for the separation and concentration of fine coals and minerals by exploiting the difference in their affinity to air bubbles in aqueous medium. Froth flotation is an effective method for beneficiation of coal and mineral particles in a certain size range. It remains difficult to upgrade ultrafine mineral particles. One of the reasons for the ineffective flotation of fine particles is the low probability of bubble-particle collision in the collection zone (i.e., the pulp zone). According to Reay and Ratcliff (1973) and Yoon and Luttrell (1989), the probability of collision is significantly affected by bubble size and particle size, and the collection zone recovery can be increased by decreasing the bubble size."

Jan 1, 2018

By William C. Hirt

Column flotation is a promising technique for processing as-mined, cobalt-rich, ferromanganese crust to separate the valuable crust component from barren substrate-rock, either aboard ship or within the water column. Column flotation testing was carried out in a seawater medium using samples obtained from the U.S. Exclusive Economic Zone (EEZ) in the mid-Pacific Ocean near Johnston Atoll. The collector reagent was a mixture of diesel fuel, fatty acid, and sulfonate previously developed at the U.S. Bureau of Mines for crust flotation using conventional flotation cells. Results are dependent upon particle size and reagent dosage, especially *as these factors affect froth volume and stability. Column flotation results are compared with previous studies in conventional cells. An overview of how column flotation might be applied in an offshore mining and processing system is given.

Jan 1, 1992

By S. K. Nicol

The results of column flotation tests conducted on a bulk sample of ultrafines discarded from the fine coal desliming cyclones at the Riverside coal preparation plant of Theiss Dampier Mitsui Coal Limited are presented. A 9% ash concentrate was obtained from a 51% ash ultrafine feed at 75-80% recovery of combustibles in a single stage of column flotation. From this result it is predicted that installation of column flotation at Riverside would lead to the annual recovery of additional coal worth $US5.1M. The operating conditions for coal and copper column flotation are compared and some differences which may result in a variation in column design are noted.

Jan 1, 1987

By D. J. Simbi, T. R. C. Fernandes, M. Nyamhunga

The recovery of P2O5 from a 90-95% minus 45 microns phosphate slimes sample was carried out in a 5.08-cm internal diameter and 549-cm high flotation column cell. The influence of the feed rate, feed percent (%) solids, and frother dosage on the recovery was investigated following a truncated cubic 3 level by 3 variables experimental design. Two three-variable interactions of feed rate (-l)/feed percent solids (+l)/frother dosage (-1) and feed rate (-l)/feed percent solids (-1)/ frother dosage (+I) gave the region of optimum column performance: recovery (52.60-74.50%), mass yield (15.68-18.80%), and concentrate grade (22.87-31.2196). The collector dosage also showed a significant influence on the column performance. The high reagent consumption relative to the current plant levels points to the need for the removal of ultrafine particles (<10 µm).

Jan 1, 1999

By C. W. Schultz

The Mineral Resources Institute at The University of Alabama is engaged in a program whose objective is to develop a beneficiation system for Eastern oil shales. Prior experience (1,2) at The University had shown that the grind required for liberation of the oil rich kerogen was substantially below 20~m. Based on this fact and the rapidly emerging consensus that column flotation is the preferred method for ultrafine particle separation, efforts were focused on the column flotation of oil shale. This paper, which must be regarded as a progress report on a continuing MRI project, describes the observations made and the results achieved to date. The investigation is being conducted in two phases. The first phase has been completed and consisted of a factorially designed experiment conducted for the purpose of screening a set of primary flotation variables. The second phase, which is still in progress, is focused on optimization of the operating conditions and development of a flowsheet for specific shales.

Jan 1, 1989

By R. Harris, M. Misra

Column flotation technology has a demonstrated potential for recovering clean coal from high-ash waste fines. The effect of different variables such as air flow rate, frother addition, depressant addition, percent solids and particle size on the quality of separation are discussed. Results indicate that air flow rate and depressant addition are the important variables which control the selectivity in the flotation of fine coal in a column cell. Separation efficiency achieved with column cells is significantly better than that with conventional flotation cells. Under appropriate experimental conditions with a deep column, more than 80 percent coal can be recovered in the concentrate containing 10 percent ash from waste fines containing over 60 percent ash.

Jan 1, 1988

By Felicia F. Peng

Two modes of collector addition techniques are applied in the column flotation for cleaning ultra fine coal. The collector can be: 1) added directly into the coal slurry through the feed system; and 2) gasified collector and transported in the gas phase through the bubbles. Operating parameters of the column flotation were investigated through three phases of work plans for Pittsburgh No.8 seam coal. In present study, the column flotation using two modes of collector addition techniques were tested and compared. Ninety percent or higher combustible recovery can be achieved by using both methods. However, utilizing the gasified collector addition technique in column flotation has more potential than direct liquid addition technique to obtain the higher recovery at same collector dosage.

Jan 1, 1993

By R. Sharma, S. Svoronos, S. Gupta, N. A. Abdel-Khalek

This paper presents the results of a column flotation study on a fine feed sample of Florida phosphate. A central composite design was used to study the main and interaction effects of parameters affecting column efficiency. The statistical design is also used to determine the optimum conditions. The results indicate that, depending on the experimental conditions, it is possible to produce a high-grade concentrate with a high recovery. A 15ppm concentration of nonionic frother was found sufficient to maximize the recovery at pH of 9.5.

Jan 1, 2002

By R. Sharma, S. Svoronos, S. Gupta, N. A. Abdel-Khalek

This paper presents the results of column flotation of a fine feed sample of Florida phosphate. A central composite design is used to study the main and interaction effects of parameters affecting column efficiency. The statistical design is also used to determine the optimum conditions. The results indicate that, depending on the experimental conditions, it is possible to achieve a concentrate of high grade and recovery. A concentration of 15 ppm of non-ionic frother is found to be enough to maximize the recovery at the pH of 9.5.

Jan 1, 1999

This paper presents the results of column flotation of a fine feed sample of Florida phosphate. A central composite design is used to study the main and interaction effects of parameters affecting column efficiency. The statistical design is also used to determine the optimum conditions. The results indicate that, depending on the experimental conditions, it is possible to achieve a concentrate of high grade and recovery. A concentration of 15 ppm of non-ionic frother is found to be enough to maximize the recovery at the pH of 9.5.

Jan 1, 1999

By G. A. Kosick, M. Freberg, L. A. Kuehn

"Highly variable and higher than forecast lead miff feed grades were problems experienced at the Polaris Concentrator. Limited flotation capacity and poor operating flexibility prevented the plant operators from overcoming these difficulties, and resulted in grades and recoveries which were lower than necessary.Two column cells were integrated into the lead circuit in an effort to give the operators the tools they required to achieve the best grades and recoveries possible, regardless of the miff feed grade. Installation of the column cells increased lead concentrate grade from 76% to 79.3% Pb, and increased lead recovery from 9/% to 91.3% Pb.This paper reviews the design, development and operation of column flotation cells in the lead circuit at the Polaris Mine.IntroductionThe Polaris Concentrator was constructed in 1980 on a barge in Trois Rivieres, Quebec, and towed to its pre sent location on Little Cornwallis Island, Northwest Territories, about 1450 km from the North Pole. The plant presently treat s about 2800 mtpd of new feed with average feed grades of 3010 Pb, 13% Zn and 5% Fe. Current production averages 36 000 tonnes of lead concentrate and 220 000 tonnes of zinc concentrate annually.The barge design and min e location dictated that the concentrator .be compact with very little unused floor space. As a result, flexibility was limited in terms of expanding the plant.Mill feed grades were highly variable and above forecast and the lead flotation circuit was found to be under capacity. This caused continued overloads in the lead cleaning circuit, resulting in low concentrate grades and recoveries. It was evident that an increase in lead flotation capacity and flexibility was necessary. The existing floor space did not allow for the installation of additional conventional flotation cells, but one alternative was the installation of column cells."

Jan 1, 1988

By Schommarz KH, Dunne RC, Goodall CM

Column cells are widely used today for the recovery of base metals by flotation. Their use for the flotation of iron sulphides has not been as rapid. Australia has pioneered the use of large rougher flotation columns. During the last six years, seven rougher columns have been installed on gold mines treating iron sulphides and the technical viability of this technology has been demonstrated. Laboratory column testwork on a gold bearing iron sulphide ore demonstrated the effects of both physical and chemical parameters. In general the large commercial columns operate over a broad range of conditions depending on the downstream treatment of the flotation concentrate. The addition of wash water to commercial columns is not universally applied and there appears to be a need for a better wash water System.

Jan 1, 1993

By H Thanasekaran, L Christodoulou, J Kohmuench

"Column flotation has been successfully applied to iron ore concentration since the 1980s with the goal of reducing silica content and allowing for the efficient production of pellet feed. Since then, columns have been widely used in iron ore processing due to: their lower capital and operational costs when compared to conventional cells their ability to generate higher concentrate grades and recoveries.Currently, more than 100 columns have been installed within Brazilian iron ore processing circuits for rougher, cleaner and scavenger duties. Despite it being a well-established approach, several technological advances have improved column design, accessories and performance. This work presents the performance of some iron ore columns in Brazil and the recent technological developments.CITATION:Thanasekaran, H, Kohmuench, J and Christodoulou, L, 2013. Column flotation of iron ore - status and advances, in Proceedings Iron Ore 2013, pp 479-484 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By J. L. Huiatt, D. G. Foot, J. D. McKay

The US Bureau of Mines compared column flotation using either fine or coarse bubbles with conventional flotation on a Montana chromite ore. On deslimed ore, fine-bubble column flotation produced a &.7% Cr2O3-grade rougher concentrate with 87% recovery, compared with 43.8% and 43.5% Cr2O3-grade rougher concentrates with 85% and 77% recovery for coarse-bubble column flotation and conventional flotation, respectively. On undeslimed ore, coarse- and fine-bubble column flotation produced rougher concentrates containing approximately 41.5% Cr2O3 with 95% recovery, exceeding conventional flotation, which produced 35.6% Cr2O3 -grade concentrates with 87% recovery.

Jan 1, 1987

By J. D. McKay

The Bureau of Mines devised a column flotation technique using either fine or coarse bubbles and compared it with conventional flotation on a Montana chromite ore. On deslimed ore, fine-bubble column flotation produced a 44.7-pct-Cr203-grade rougher concentrate with 87-pct recovery, compared with 43.8- and 43.5-pct-Cr203-grade rougher concentrates with 85- and 77-pct recovery for coarse-bubble column flotation and conventional flotation, respectively. On undeslimed ore, coarse-and fine-bubble column flotation produced rougher concentrates containing approximately 41.5-pct-Cr203 with 95-pct recovery, exceeding conventional flotation which produced 35.6-pct-Cr203-grade concentrates with 87-pct recovery.

Jan 1, 1985