Search Documents

By Vijayakumar Viramuthu, Martin Heinrich

Tower of Lot L, L1 & M, Kuala Lumpur City Centre when completed would stand 700 m tall. This Mega tall Skyscraper would merely be less than 500 m away from the world tallest Twin Tower, the Petronas Twin Tower. From June 2018 to February 2020 BAUER (MALAYSIA) SDN. BHD. constructed 225 nos bored piles with diameters of 2.0 m and 2.5 m for this tower. To comply with the depth requirement of the initial design and the need to have the pile toe 2.0 m above competent bedrock, the drilling equipment was required to be able to achieve a maximum drilling depth of 150 m. Actual piles constructed on site were deeper than 120 m. These dimensions caused superlative challenges which included but were not limited to controlling the open borehole stability over time with polymer, installing 70 t heavy steel cages and pouring up to 550 m³ concrete continuously in conjunction with installation of 88 t heavy kingposts into workable fresh concrete. The piling works were executed with one BAUER BG 48 and one BG 72, the biggest drilling rig globally available.

May 1, 2022

By Michael Traylor, Michael Jatczak, Brett Robinson

The Detroit River Outfall No. 2. is an effluent water conveyance system linking the Detroit Metropolitan Wastewater Treatment Plant to the Detroit River. The 6.4m (21ft) finished diameter tunnel extends 1,890m (6,200ft) east from the bottom of a 91m(300ft) deep, 9.2m (30ft) diameter drop shaft. At the eastern terminus of the tunnel, six Riser Shafts connect the tunnel to diffuser heads on the riverbed. The tunnel runs through a highly fractured Limestone formation capable of producing high levels of groundwater in?ows and Hydrogen Sul?de gas. Control of this water and gas was a theme which ran through the entire Project’s design and construction. This paper will provide an overview of each portion of the Project’s construction, including the Entrance Shaft, Precast Concrete Segments, TBM Tunnel, Pre-Excavation Grouting Methods, and the Riser Shafts.

Jan 1, 2003

By Dan A. Brown

The foundations at the Huey P. Long Bridge in New Orleans presented special challenges for construction due to the requirements for very deep drilled shafts in the Mississippi River beneath the existing bridge structure. Drilled shafts were constructed to depths of approximately 200ft in alluvial soils using a rotator system with full-length segmental casing, and base grouted to improve axial resistance. This paper describes the design and construction of the work platform to provide access to the restricted-access site beneath the existing bridge, the approach used to construct the drilled shafts, and the results of a load test program to verify the axial resistance.

Jan 1, 2010

By Don Hickey

The MTA in conjunction with LIRR, are in the process of expanding one of the largest commuter railroads in the country, with over 260,000 passengers a day. The LIRR, which provides 700 passenger trains every 24 hours, can?t continue on the present growth course as a joint tenant in Penn Station with Amtrak and NJT. For this reason, in conjunction with the fact that over 53% of LIRR?s current riders into Penn Station are ultimately bound for the East Side of Manhattan opening, have created the need for the expansion of the LIRR. The complete expansion will cost approximately 6.3 billion dollars and all of the contracts are to be completed by 2013.

By Brian Fulcher, John Eastlund, J. B. Copeland

Following the completion of the 7,600 m primary access tunnel by Kiewit/Parsons Brinckerhoff (K/PB) in April 1997, an exploratory East-West Cross Drift Tunnel was constructed at the Yucca Mountain Project over the proposed future repository block for high level nuclear wastes. The 2,681 m (8,796 LF) East-West Cross Drift Tunnel was excavated through volcanic tuffs having zones of incompetent rock using a re-built Robbins 5.000 m (16’-5”) hardrock TBM with a special arrangement of supporting equipment. Details of the unusual site and contract conditions will be discussed as well as with the unique tunnel equipment specified by the Owner. This portion of the Yucca Mountain project required eight months to complete.

Jan 1, 1999

By A. J. Stewart, R. L. Shufflebotham, D. W. Ferguson, T. L. Page

The Inter-Island Tunnel is a 7.7 kilometer (25,160 foot) long by 3.5 meter (11.5 feet) diameter concrete lined tunnel through the Cambridge formation below Boston Harbor. Constructed as part of the Boston Harbor Project, this tunnel will bring untreated wastewater from the MWRA’s South System headworks facility at Nut Island in Quincy, MA to the new Deer Island treatment plant. A myriad of problems delayed the construction of the tunnel. These problems included salt water inflows of over 22,000 liters (5,812 gallons) per minute, a major fire in the access shaft, weak rock and soil collapsing on the tunnel boring machine, and hand mining operations.

Jan 1, 1997

By Patrick J. Doig

The Lewis Street CSO Tunnel is an important element in the efforts of the Metropolitan Government of Nashville and Davidson County (Metro) to improve the treatment of waste-water in the area. The tunnel is approximately 1,675m (5,500ft) long with a finished diameter of 2,600mm(102inches). 116m (380ft) of tunnel was constructed in soil with the balance being in lime-stone rock. Excavation was with a 3,700 mm (12ft) diameter Jarva hydraulic shield in soil and a Jarva Mark 12 TBM in rock. The permanent lining of the tunnel comprised concrete pipe with steel end-rings and a vinyl liner. This paper describes the construction of the project with particular emphasis on the excavation and lining of the tunnel.

Jan 1, 1997

By Miguel Angel Banuet Rodriquez, Hector Conceso Aragon

"Construction of the longest road tunnel in Mexico is part of Acapulco’s alternate roadway to the scenic roadway project. This article provides a brief summary regarding details of the construction since the project began. Work was done by skilled engineers and Mexican workers that includes outstanding execution of the work in an urban and tourist area. This project will have a strong impact on the steady development of the port of Acapulco.Project locationAcapulco’s Alternate Roadway Project is currently under construction in the city of Acapulco, located in the Guerrero state of Mexico. It is an 8-km (5-mile) long roadway that starts at the Icacos neighborhood, heading toward Acapulco’s airport, crossing a drill-and-blast tunnel that is 3,160 m (10,350 ft) long under Veladero Park, a mountainous area. The tunnel overburden reaches a depth of 380 m (1,250 ft) approximately at the central point of the horizontal alignment, and continues with a 4-km (2.5-mile) long elevated road to connect to the existing Viaducto Diamante toll road (Fig. 1).Tunnel construction has already been finished using two portals for drilling and blasting operations; Brisamar Portal on the west side and Cayaco Portal on the east side (Fig. 2).Geometric dataOnly two main excavation cross-sections were considered in the executive design. The first one corresponds to the running tunnel for a three-lane vehicle section, with crosssection areas between 120 and 130 m2 (1,290 and 1,400 sq ft) taking into consideration different geological and geotechnical conditions to be encountered (Fig. 3).The second one corresponds to eight emergency bays, each one 50 m (164 ft) long, laid down within the tunnel outline, located at 400 m (1,312 ft) from each one with excavation cross-sections between 156 to 169 m2 (1,680 to 1,820 sq ft), in accordance to geological and geotechnical conditions to be encountered (Fig. 4).The tunnel’s horizontal alignment is completely straight, having a small curve within the vertical alignment on Cayaco portal, because there were some differences in levels when tunnel excavation started. Tunnel slopes were designed in such a way that rainwater does not run down into the tunnel at any time."

Jan 3, 2018

By F. Keith Jacobson

To be involved in the construction of a deep dredged caisson for a major bridge pier is one of the most rewarding and professionally challenging experiences one can have in the bridge construction business. That experience was doubled in the construction of the two deep dredged caissons for the Highway 82 Bridge over the Mississippi River near Greenville, Mississippi. The challenges and the construction risks associated with constructing these two dredged caisson pier foundations highlight the construction engineering innovation associated with major bridge pier construction. The 1,378-foot Main Span of the Highway 82 Bridge makes it the longest cable stayed bridge span over the inland rivers of the United States. The main piers for this bridge are supported on two dredged caissons measuring 80-feet by 122-feet in plan, founding 200-feet and 170-feet below the river surface. The challenges of constructing these caisson structures, sinking them through 70-feet of water to the river bottom and then excavating and further sinking them to the founding grade without exceeding the design tolerances, were enormous. The construction engineering opportunities for innovation included major breakwater structures to create a friendly environment in 11 ft/sec currents, the first time use of Articulated Concrete Mattresses for river bottom scour control, unique air dome design to maximize the buoyancy of the caisson structure while floating, a caisson guide system to assure positive control and positioning of the caisson during the initial sinking phases, and a comprehensive sinking plan to assure maximum control and minimum risk. Many of the innovative solutions to the construction challenges on this bridge will be incorporated into future caisson construction projects on the lower Mississippi River.

Jan 1, 2013

By F. Keith Jacobson

To be involved in the construction of a deep dredged caisson for a major bridge pier is one of the most rewarding and professionally challenging experiences one can have in the bridge construction business. That experience was doubled in the construction of the two deep dredged caissons for the Highway 82 Bridge over the Mississippi River near Greenville, Mississippi. The challenges and the construction risks associated with constructing these two dredged caisson pier foundations highlight the construction engineering innovation associated with major bridge pier construction. The 1,378-foot Main Span of the Highway 82 Bridge makes it the longest cable stayed bridge span over the inland rivers of the United States. The main piers for this bridge are supported on two dredged caissons measuring 80-feet by 122-feet in plan, founding 200-feet and 170-feet below the river surface. The challenges of constructing these caisson structures, sinking them through 70-feet of water to the river bottom and then excavating and further sinking them to the founding grade without exceeding the design tolerances, were enormous. The construction engineering opportunities for innovation included major breakwater structures to create a friendly environment in 11 fUsec currents, the first time use of Articulated Concrete Mattresses for river bottom scour control, unique air dome design to maximize the buoyancy of the caisson structure while floating, a caisson guide system to assure positive control and positioning of the caisson during the initial sinking phases. and a comprehensive sinking plan to assure maximum control and minimum risk. Many of the innovative solutions to the construction challenges on this bridge will be incorporated into future caisson construction projects on the lower Mississippi River.

May 11, 2007

By Bob Rautenberg

The Construction of Tunnel and Edison Force Mains contract involves the installation of two new force mains to provide a redundant means for sewage conveyance from Middlesex County Utility Authority?s (MCUA) Edison Pump Station on the northern shore of the Raritan River to the Central Wastewater Treatment Plant on the southern shore. The force mains will be installed in a 1,192 m (3,910 lineal foot) long tunnel with a 4.09 m (13'-5') inside diameter, fully gasketed precast concrete segmental lining, which is to be tunneled underneath the Raritan River utilizing an Earth Pressure Balance TBM. The tunnel is anticipated to encounter flowing soils near and beneath the river. Two new 60-inch diameter Centrifugal Cast Fiberglass Reinforced Polymer Mortar force mains will be installed within the tunnel leaving an open utility corridor above the force mains for future consideration. The project also includes the design and construction of two slurry wall shafts with associated piping. The paper will provide an overview of design and provide a case history of the construction of the tunnel and highlights of the construction methods implemented to date.

The underground storage of LPG and other hydrocarbons is in current commercial use in Northern Hemisphere countries in Europe, Asia and the USA.Elgas Pty Ltd, a 50 per cent joint venture between AGL and BOC, embarked on a worldwide feasibility investigation in 1989 to establish the viability of constructing an underground LPG storage facility in Sydney, Australia, the first of its kind in the country. Elgas recognised that with the limited 19 000 tonnes of storage capacity at Port Botany and the limitations imposed by use of small coastal ships (up to 10 000 tonnes capacity), a larger storage facility was required to utilise higher capacity ships from more remote sources such as the North West shelf and overseas. This would achieve security of supply in high demand periods and economies of scale. The underground option also provides improvements to safety and environmental standards.

Jan 1, 1999

By Joseph A. Whitchurch

The N20 to N25 Tunnel (basic) segment was the second tunnel contract awarded for construction by The PB/MK Team. This project embodied 3.9 km (2.4 miles) of tunnel and was located within the northwest quadrant of the 86.9 km (54 mile) long main collider ring. The contract required the excavation and initial support of a 54.3 m (178 vlf) deep ventilation shaft, a connecting horseshoe shaped Adit and TBM starter tunnel and 3,865 m (12,680 If) long main collider tunnel with a 4.3 m (14 ft) minimum finished diameter. This paper discusses the construction methods, equipment utilized and the production achieved in the construction of the ventilation shaft, connecting adits and the main collider tunnel.

Jan 1, 1995

By Justin Brown, Michael Kobler, Dave Ragland, Bob Shufflebotham

PROJECT OVERVIEW As the sun-bronzed San Diego students strolled casually to class, mining crews from Atkinson Construction were working only 9 meters below the surface. The330 meter long, 11.3 meter diameter squat ellipse NATM tunnel is part of the9.3 kilometer Mission Valley East Extension Light Rail Transit (MVE-LRT) being constructed for the San Diego Metropolitan Transit Development Board (MTDB). The SDSU segment of the MVE-LRT was awarded to the Clark Construction Group, the parent company of Atkinson Construction for $82.7 million. URS CORP was the prime designer and Hatch Mott MacDonald performed the NATM tunnel design. The construction managers were Washington Infrastructure Services with Underground Construction Managers, EPC Consultants, and ILF Consultants. A NATM tunnel design was chosen as the most cost-effective way to minimize disruption of the university activities. The tunnel passes close to several buildings and directly below access roads, tennis courts and a baseball field. The NATM method of conventional mining uses shotcrete for ground support often reinforced with steel orplastic fibers, welded wire mesh and lattice girders. The tunnel runs from a cut and cover box up a 4.2% grade in a 217 meter radius left-hand curve with several spirals and ends at the underground station 330 meters away. The depth of cover varies from 16 meters near the west portal to nine meters at the station. The design called for a two-pass system with a primary lining of 300 mm shotcrete with lattice girders at 1 m centers and two layers of welded wire mesh. The lattice girders are used primarily for profile control and are not considered a structural element. The top heading was designed to be excavated in one of three excavation sequences depending on ground conditions and depth of cover. In sequence one excavation, the top heading is excavated in two halves with a one-meter separation. In sequence two excavation, a side gallery is advanced 8 or more meters ahead of the

Jan 1, 2003

By Makoto Suzuki

After hot rolling, stainless steel strip is processed by the Hot Rolled Annealing and Pickling line (HAP) , where H2SO4 or mixed acid of HNO3 and HF is normally used. In the pickling bath, metal oxide accumulates in the form of sludge, which should be removed from the bath regularly. A new automatic continuous sludge disposal system has been introduced at Chiba Works of Kawasaki Steel Corporation to increase sludge removal efficiency and improve the working environment. The elements of the equipment are as follows. a. Ejectors in pickling bath: to carry the mixed acid into the circulation tank through the piping system. b. Sedimentation bath : to sediment sludge out of the bath. c. Skip conveyer : to convey a specified volume of sludge into a kneading for device for neutralizing. The sludge removal efficiency of this system is very high. and the volume of sludge accumulation in the pickling bath has substantially decreased.

Jan 1, 1996

By David Chastka, Isidro Rivera, Shawna Von Stockhausen, Idit Zarchi

The City of Santa Cruz Water Department is replacing the existing Newell Creek Dam inlet/outlet works at Loch Lomond Reservoir in the San Lorenzo Valley. The project will improve the City’s overall operational efficiency, improve system performance, and improve the safety and reliability of storage for the City’s drinking water supply. The project comprises new inlet works* (three new inlets that control and convey flows into and out of the reservoir, and an intake control building), an inlet/outlet tunnel with a 48-inch conduit to convey flows into and out of the reservoir, and a new outlet structure at the toe of the dam. The outlet structure includes a release point for energy dissipation of emergency drawdown flows, a connection to Newell Creek Pipeline, and beneficial releases into Newell Creek. The project also includes a new dam seepage collection and monitoring system and appurtenant structures such as a culvert bridge over the spillway plunge pool to improve access to the new outlet. Notable complex project components include in-water work to connect the new intake shaft pipes to the three new inlets. The project includes one major milestone with a work window regulated by environmental permits that could only be amended/ extended with approvals from those agencies. If not met, the milestone work would have caused significant delays (potentially up to one year) to the project.

Jun 13, 2021

By J. Davies

This paper describes the successful management and construction of the 5.18 m (17 ft) diameter, segmentally lined, North Dorchester Bay CSO storage tunnel in Boston, MA. This 3,300 m (10,830 ft) long tunnel was mined through variable soft ground with only 6 m (20 ft) of cover, using an earth pressure balance tunnel boring machine. These extensive data collected from the projects unique automated and internet accessible geotechnical and TBM monitoring system, will be examined and used to explore the relationships between geological conditions, TBM operating parameters and measured settlements. The paper will also discuss the use of screw revolutions as an indicator of muck volume.

By Christopher Laughton, Michael P. Bruen

At Fermilab, a 4000-ft long underground complex has recently been constructed for a high-energy physics experiment. The complex is sited up to 350 ft, below grade principally in bedrock. The rock excavations were mined by TBM and drill and blast methods and supported by a combination of rock bolts, dowels and shotcrete. Water control was achieved using a combination of pre- and post-excavation grouting, drainage systems, drip shielding and air desiccation measures.

Jan 1, 2003

By Russell Clough

The Pacheco Pumping Plant is situated on the west end of San Luis Reservoir in western Merced County, California. It is designed to draw water from the reservoir and pump it into a 3,500,000 gallon regulating tank. The water then flows entirely by gravity to the Coyote Pump Station in Morgan Hill, a distance of 40 miles, where it is pumped into Anderson Reservoir. This water is used to recharge the depleted groundwater table in the Santa Clara Valley. Eventually, some of the water will be diverted to Hollister in San Benito County and to Watsonville and Santa Cruz in Santa Cruz County. The owner is the United States Bureau of Reclamation. The underground work consisted of a fifteen foot finished diameter surge shaft 250 feet deep to the crown of the pump chamber; a twenty foot finished diameter pump chamber which declined from the shaft at 14.2% for ninety feet and then ran horizontally for 180 feet; and twelve each five foot diameter steel lined intake shafts 240 feet deep which intersect the pump chamber in the horizontal section. (Figure 1) Upon completion of the pump chamber, the contractor had to dewater the existing tunnel under the reservoir, excavate the remaining fifteen foot plug, and concrete the transition. The low bidder for this contract was Underground - Continental-Heller at 414,456,000. Excavation of the open cut for the pumping plant and surge shaft began on April 14, 1983. This was performed using a Koehring 1066D backhoe, dozer, trucks, and two Cat 631 scrapers. The excavation was started at the surge shaft so that the grouting could begin

Jan 1, 1985

By Patrick J. Doig

In mid-1991, the design/build contractor set to work on the Pergau HEP in a remote corner of Malaysia, armed with only a slim volume of conceptual drawings. The next five years saw roads, power lines, buildings, dams, and over 30 kilometers of tunnel constructed, followed by two years of E&M installation and commissioning. Along the way, the project overcame geothermal groundwater, faults, land disputes, monsoon rains, marauding tigers, and those most fearsome of foes, politicians and the press. This paper is a testament to the ingenuity, commitment, and persistence of the construction industry professionals who brought this massive project to fruition.

Jan 1, 2001