Search Documents

By X. L. Huang

This paper deals with the experimental and theoretic study of the contact pressure beneath the deep foundation of Beijing International Hotel, The experiments have been carried out in project and in model footing 6.6m2. The result of measurements shows the contact pressure at the edge is greater than that at the center. The theoretic analysis on the base of elastic theorey is in good agreement with the test if the proposed assumption used.

Jan 1, 2010

By C. Snyman, M. Le Roux, Q. P. Campbell, S. Engelbrecht

Due to the ultrafine particle size required for effective processing of chromite ores, dewatering of the concentrates presents a challenge. It is not uncommon for the ore to have elevated moisture contents even after dewatering, which must be reduced to required levels of between 8% and 10% by mass for further processing. Contact sorption drying has shown promise in test work on fine coal. This method was used to study the dewatering of chromite on a laboratory scale using 3 mm spherical activated alumina ceramic beads as a sorbent. Three different sorbent-to-chromite mass ratios, namely 0.5:1, 1:1, and 2:1, were tested with different process conditions, including dewatering in a stationary and a rotatingl bed. The experimental work showed that it was possible to achieve the target moistures in less than 10 minutes, irrespective of the sorbent-to-chromite ratio used. Ratios of 1:1 or higher, however, proved to be the best. The sorbent reusability at mass ratios of 1:1 and 2:1 were therefore tested. With a 1:1 mass ratio, the sorbents could be reused for three cycles, while with 2:1 ratio, the number of cycles increased to six. The sorbent-to-chromite mass ratio used had a significant influence on the required contact time and the reusability of the sorbents.

Oct 3, 2023

By Robert Glass Cleland

THE DEATH of William E. Dodge occurred at a time when, all unwittingly, the company in which he had so long been the dominant factor was about to break with its old practices, its old traditions, its old interests, and transfer its major activities three fourths of the way across the continent and engage in an enterprise that differed almost as much from the original Phelps Dodge undertakings as the rough, arid mountains of the new region differed from the green hills and valleys of New England. To understand the effect of this transformation upon the fortunes of Phelps Dodge, one must change the setting of the present narrative from the familiar locale of the Atlantic seaboard to the land of "distance, silence, and solitude," that men called Arizona. In 1880 that Territory was one of the last frontiers of the Old West. To the Spaniards it had been a land of mystery and fable, the limit of the King's settlements, the far edge of the rim of Christendom. Through it Coronado; in a vain effort to find the fabulous Cities of Cibola, had led "the most brilliant company ever assembled in the Indies to go in search of new lands." Below its southern border, Father Kino, the "steel-thewed" Jesuit described by his

Jan 1, 1952

By E. I. Vargha-Butler

The determination of surface tensions and contact angles of coal particles is of great interest for coal beneficiation processes such as froth flotation and oil agglomeration and for the inclusion of coal particles into oil droplets as a means of enriching the fuel. Methods for contact-angle measurements on small irregularly shaped solid particles have not been available in the past. Therefore, we recently developed a novel technique to determine contact angles and surf ace tensions of coal particles. Two types of bituminous and one type of subbituminous coal particles have been tested. The technique used is called the freezing-front technique and it considers the behaviour of the test particles (in the range of 20-250 pm) at the solidification front of carefully selected, well-defined solidifying melts (matrix materials) such as thymol, biphenyl, naphthalene, salol and 2-phenyl phenol.The results show that the technique works well, providing quantitative and detailed information on the wettability of coal particles. The sensitivity of the method is so high that a difference in contact angle of approximately 4 degrees between the smaller and the larger particles is clearly registered.

Dec 1, 1981

By X. Cui, H. Ding, J. Wen, Q. Gu

This study is a continuation of previous work designed to further explore the mechanism of the bioleaching of sulfide concentrate at neutral pH by heterotrophic bacteria Bacillus megaterium QM B1551. The concentrate contained 13.2 percent nickel (Ni) and 0.2 percent cobalt (Co), which presented primarily as pentlandite and pyrrhotite. Contact and noncontact bioleaching experiments were conducted with finely ground ore at an initial pH of 6, resulting in 44.7 percent of Ni and 38.2 percent of Co leached in the contact-bioleaching treatment. Oxidation experiments of sulfur, thiosulfate (S2O32−) and ferrous ions (Fe2+) by cell membrane were performed to verify whether sulfur transferase, thiosulfate quinone reductase and enzyme cytochrome B558 on the surface of the bacteria could be expressed to oxidize the sulfide. The results show that thiosulfate quinone reductase and cytochrome B558 could be expressed to oxidize S2O32− and Fe2+ to SO42− and Fe3+, respectively.

By Damir Dedic, Wörle. Patrick

"Soil properties within a construction project area are analyzed during the planning phase. However, it is only possible to achieve selective soil exploration, even in the case of very extensive investigatory programs, which results in a certain soil risk and uncertainties for planning and execution.Therefore, the application of monitoring systems is becoming increasingly important in the field of geotechnics. The application of suitable monitoring systems for these particular purposes provides considerable knowledge relating to the load bearing behavior of the soil and the ground anchor. Applications that present major challenges to measuring anchor forces include back-anchorages of long-lasting and very deep construction pits, construction pits in urban areas, slope and embankment supports for track and vehicular routes, port and lock structures, and uplift control. Apart from overseeing individual construction stages, monitoring systems analyze the interaction between the soil and structure throughout the latter’s entire life cycle and safeguard the functional capability of the applied system components. Geotechnical construction projects can be adapted, optimized and carried out with enhanced safety from the information obtained.Conventional Monitoring SystemsThere are numerous approaches for determining anchor forces of bar or strand anchors. Lift-off tests and measurements with load cells are the most common methods.Lift-off Test: Lift-off tests provide a possibility to monitor the prevailing force in strand or bar anchors. The entire anchor head structure is lifted using the appropriate equipment. The steel tendon is prolonged, or in the case of strand anchors, a screw-on cap holds the wedge carrier so that a tensioning jack can be mounted above it. Then, the tendon is prestressed until the lower anchor nut (bar) or wedge carrier (strand) is lifted off from the anchor plate. The intersection of the two straight lines in the figure represents the force at which the anchor nut or the wedge carrier lifts off from the anchor plate. Thus, the intersection displays the actual load of the anchor. This form of anchor force control gives conclusive results, but at the same time requires extensive accessories and extra personnel to execute the test. For this test, a sufficient bar overhang must be available, the wedge plate must possess an external thread, or there must be a strand overhang of at least 24 in (60 cm). Furthermore, the anchor head must be freely accessible and in a position to be reached with the necessary equipment."

Jan 1, 2017

By Carlos Zevallos, Julia Zea, Francisco Alejo

Este estudio evaluó la recuperación de cianuro utilizando polipropileno (PP) y politetrafluoroetileno (PTFE) y el impacto de las condiciones de operación con aguas residuales mineras sintéticas y reales. Los resultados muestran un mejor rendimiento de la membrana con la membrana de PTFE frente a la membrana de PP, así como una impacto del pH del destilado, la temperatura y la concentración de cianuro de alimentación en la eficiencia del proceso. En cambio, concentraciones de cianuro destilado mostraron un impacto muy limitado en el rendimiento del proceso, lo que sugiere un impacto limitado. Se requieren recursos de agua dulce para la recuperación de cianuro.

Sep 29, 2023

This paper on the relation of Granite and Sedimentary Contacts to Victorian Mining will, it is hoped, be of interest to members of the Institute.The broad fact that gold often occurs' at or near the junction of granite with sedimentary silurian or metamorphic rocks has been noted by some Victorian geologists, miners, and prospectors; but the fuq practical value -of the fact does not seem to have been fully realised by prospectors. Glancing at the Geological" Map of Victoria, one can see that many of our goldfields 'are situated at or near the junction of granite with Palceozoic sedimentary formations, and that some of our alluvial fields are on granite. Many prospectors are possessed of this knowledge but when prospecting a contact locality, they would be just as likely to confine their search for auriferous matrices to spots a quarter of a mile on the sedimentary side, as on the actual contact line of two formations.

The growth of "Unit Load-cargo handling technology in world cargo lin- er trades over the last decade has cre- ated a situation in which special pur- pose-vessels (cellular container ships, roll-on/roll-off vehicle deck ships and Lash type vessels) are rapidly replac- ing conventional cargo ships, the principal means previously available for transporting heavy lifts. Consequently heavy lift traffic has tended to accumulate awaiting ship- ment, especially where discharge is required in "off beat" locations. A partial solution to this problem will be provided by new and small but exceptionally versatile ocean going heavy lift carriers now finding their way into world trade routes. These new ships combine extremely high lifting capacity, high manoeuvreability and exceptionally shallow draft with bow and stern Ro/Ro capability. They can handle rolling loads of exceptional size and weighing up to 1,000 tons Each. But the problem is a far larger and more serious but essentially a domestic one. Major industrial pro- jects in Australia will require pro- gressively heavier and larger plant and construction sites are becoming much more inaccessible. Whereas these new ocean going heavy lift carriers have ample capacity to satisfy part of the total transport requirement, there is clear evidence to show that domestic transport resources have little if any potential for increase in capability at the same rate as demand or at the same rate as sea transport facilities. Resolution of the larger problem is within reach but only through a pro- perly co-ordinated approach to future planning for the overall needs of large scale projects on a national basis. This co-ordinated approach must involve Federal and State government transport administrators, railway and highway authorities, shipping and road haulage interests and finally the planners of the projects which require these improved heavy haulage services.

Jan 1, 1973

By C Doblin

Any value addition to the mineral sands in the Murray Basin (Australia) will generate waste that needs to be disposed of safely. For example, conversion of ilmenite and synthetic rutile to titania (TiO2) pigment would generate large amounts of environmentally undesirable elements. Processing of U+Th containing zircon sands to zirconia or to higher purity zircon would generate a low-level radioactive waste. In this study it is proposed that one way to circumvent the waste problem could be to contain such waste in magnesium-based (Sorel) cements. Containment of waste in magnesium cements is an attractive idea especially for the mineral sand processing companies that could operate in the Murray Basin in the future, because the required magnesium oxide and magnesium chloride may be made cheaply from the saline waters encountered during mining operations. The magnesium cement production process is also far less energy intensive than the Portland cement production process. The results of this study indicate that mixing a waste stream with a slurry of magnesium cement before being discharged to the disposal area would contain the waste in a æconcrete-likeÆ structure, resistant to dispersion by wind and moderate rain. However, some loss of strength and increased leaching of impurities, Mg and Cl could take place in wet climate areas. Ongoing research is being concentrated to develop a new process for making water-resistant magnesium cement.

Jan 1, 2002

By Maurice L. Madden

An investigation was undertaken for a ground water discharge plan for the Chino mining complex near Hurley, New Mexico. Operations which impact ground water include dump leaching, storage reservoirs, and tailings seepage. The investigation included both hydrogeological data collection and laboratory analysis. A conceptual understanding of surface water and ground water was then developed. Surface water and ground water models were used to match existing conditions and predict the impact of operational modifications. The study concluded that runoff and resulting leach reservoir overflows were primarily responsible for the ground water degradation. Tailings seepage represents a smaller part of the impact.

Jan 1, 1984

By Anton Sizo, Alexey Klyashtorin

The Gunnar uranium mine operated from 1953 to 1961 on the shore of Lake Athabasca, in 1964 the site was abandoned, and the mine pit flooded. In 1981, the pit was found to be stratified with a chemocline at ~70 m by a sharp change in conductivity and TDS. The uranium concentration was ~700 μg/l on the surface, 320 μg/l at 50 m, and 2,900 μg/l at 110 m. The Ra-226 concentrations were 0.1, 0.06, 0.12, and 0.4 Bq/l. By 2017, the chemocline was ~60 m deep. The highest uranium concentration was 1150 μg/l and the lowest concentration (220 μg/l) was attributed to the chemocline. In the deeper column, the uranium content varied around 750 μg/l. The uranium distribution down the pit profile was aligned with DO, ORP, and TDS. Ra-226 averaged to ~0.4 Bq/l, Ra-226 and uranium profiles were inversely related with the respective maximum and minimum attributed to the chemocline. The uranium and radium amount accumulated in the pit by 2017 was 3,420 kg and 2,163 GBq, respectively. The uranium and radium apparent accumulation trend estimates to 64 kg/y and 41 MBq/y, respectively. A stable chemocline and no concentration gradients in the other parts of the pit suggest that the contaminants are unlikely to inflow from the bottom opening or outside the pit, but rather are mobilized from the pit walls. The contaminants are not in a steady state, and concentrations of both uranium and radium are likely to increase slowly in the future if no remediation occurs.

Jan 1, 2020

By Julie Culverhouse, Dennis Grimm, Kieran Harding, Jean-Francois Boulanger

"Agrium’s Canadian Phosphate Business (CPB) is comprised of Kapuskasing Phosphate Operations (KPO) in Northern Ontario, Canada’s only operating phosphate mine, and Redwater Phosphate Operations (RPO) in Alberta, which manufactures the fertilizer from KPO’s concentrate.Production from KPO’s South Pit commenced in 2009 and introduced contaminant problems: high aluminium from crandallite and kaolinite clays. These issues caused a drastic decrease in P2O5 recovery and throughput in both plants. KPO attempted to reduce Al clays by means of aggressive desliming. Meanwhile RPO experienced high amounts of dissolved metals in their feed that are detrimental to fertilizer production.This paper covers the mineralogy of the problem, its impact on contaminant separation at KPO, on RPO’s process and on Agrium’s Canadian Phosphate Business as a whole.Potential solutions to the problem are discussed and analysed, including a process change to deslime high aluminium streams more aggressively and high grade ore flotation, which is atypical at KPO. The latter is a demonstration of the value of communication between the concentrator and the client, as KPO accepted a recovery loss and increased production costs in order to increase overall CPB profits. General lessons learned are discussed, followed by a section on ore blending.INTRODUCTIONAlthough the existence of the Kapuskasing phosphate deposit has been known since the 1970s, it’s only since 1999 that Agrium has been operating the Kapuskasing Phosphate Operations (KPO). The mine consists of three major pits (Center, North and South) from which a mining contractor hauls the apatite ore to the Agrium concentrator. The beneficiation plant processes the ore, separating contaminants such as Fe, Mg and Al which are detrimental to its client, Agrium’s Redwater Phosphate Operations (RPO). The KPO concentrate is finally thickened, filtered and dried before being shipped by rail to RPO.At the Redwater plant, the KPO concentrate is added to a sulfuric acid solution in an attack tank, to create a phosphoric acid solution and gypsum:"

Jan 1, 2011

By L. R. Moore

The World Health Organization (WHO) considers contamination from oxyanions, such as selenium and arsenic, a global concern. While their elemental forms are toxic, the aqueous oxyanions are more so. These aqueous forms, which exist at a higher oxidation state, are the most common forms released during mining processes. Many technologies are capable of meeting the governmental discharge criteria for oxyanionic contaminants, but may possess limitations due to redox chemistry as well as the water matrices. An innovative technology was developed that can successfully reduce such aqueous forms generated during mining processes to a level below the discharge criteria. This paper discusses how an understanding of the sensitivities of this novel adsorbent towards these variations in water matrices and redox chemistry can be used to optimize its application.

Feb 27, 2013

By William H. Mount

INTRODUCTION Effective mine ventilation is required to maintain a healthy underground environment for humans. Without effective ventilation, the environment can become unhealthy or hazardous as a result of the depletion of oxygen, contamination with toxic gases, or the buildup of an excessive amount of particulate matter (dust). Each contaminant has an upper limit of concentration that should not be exceeded within an 8-hr period. This is known as the threshold limit value (TLV). The TLV represents an acceptable level of exposure that should produce no ill effects. Unfortunately, more than one contaminant may be present at any one time and the effects of the individual contaminants may be additive, i.e., the effects of each contaminant must be considered simultaneously to determine the potential danger to miners. Possibly the greatest threat to mine-air quality is the uncontrolled underground use of the diesel engine. The diesel engine was invented in 1892 by Rudolf Diesel. His intention was to develop a power source that could burn coal dust as a fuel, but he was unsuccessful in that attempt and had to resort to liquid petroleum fuels (Johnson, 1975). In 1898, the diesel engine was intro¬duced into the United States by Adolphus Busch, who anticipated using it as a prime mover in factories and generating plants. At that time, the diesel engine was a very large and very heavy engine, designed for fixed installations. By 1919, lighter engines were being developed, and by 1931, Caterpillar was marketing a diesel-powered, track-type tractor (Henderson, 1975). Since 1931, the diesel engine has evolved into an extremely popular prime mover in medium and heavy-duty applications. Efficiencies now are on the order of 40% and improvements such as turbocharging and aftercooling have produced engines capable of generating power at a ratio of 0.3 kW/kg (1.0 hp per 5.0 lb) of engine weight. Although the diesel engine is relatively efficient as a mobile power plant, it is far from efficient in terms of the energy produced from the energy potential of the fuel. About 60% of the heat value of the fuel leaves the engine as wasted heat, with about 50% of that heat being emitted through the exhaust pipe and the other 50% being emitted through the radiator or cooling fins. Perfect combustion in an engine would produce only water vapor (H_0), carbon dioxide (CO_), and nitro¬gen (N2) as the byproducts. Since the diesel is not a perfect engine, each pound of fuel burned generates 5.6 m° (200 cu ft) of exhaust gas, containing about 0.009 m3 (0.33 cu ft) of carbon monoxide (CO), 0.009 m' (0.33 cu ft) of nitrogen oxides (NO, NO2, and NOD), and 0.57 m3 (20 cu ft) of carbon dioxide. The balance of the exhaust emission consists of free nitrogen and water vapor (Hurn, 1975). Contrary to popular belief, the diesel is not inherently dirty. Under normal operating conditions, a well-maintained engine neither smokes nor smells. However, the same well-maintained engine can and does produce toxic emissions. A diesel engine is not inherently safe and constitutes a distinct hazard to personnel. This chapter is devoted to a description of the various toxic substances that may be generated by a diesel engine. Although some of these substances may also be produced by blasting or natural causes, the focus of this chapter is on the relationship between the internal- combustion compression-ignition engine (the diesel) and the quality of the mine air. CARBON MONOXIDE Combustion Process During the combustion process (burning) of organic fuels, each atom of carbon combines with two atoms of oxygen, provided that a surplus of oxygen atoms is available. Thus, the carbon is oxidized to carbon dioxide. Most open flames, such as trash fires, camp fires, gas ranges, etc., produce carbon dioxide. However, with insufficient oxygen, incomplete combustion results as the carbon atoms each combine with one atom of oxygen to produce toxic carbon monoxide. Burning charcoal briquettes produce carbon monoxide because the combustion takes place inside the briquettes where sufficient oxygen is not available to the combustion process. Internal-combustion engines, whether burning gasoline or diesel fuel, also produce carbon monoxide. The only oxygen available to the combustion process is that trapped within the cylinder. If the amount of fuel delivered to the cylinder is excessive, there is insufficient oxygen for complete combustion and carbon monoxide production results. In a normally aspirated (nonturbocharged) diesel engine, the amount of air "sucked" into a cylinder is the same on every intake stroke, resulting in complete combustion only at low levels of engine loading, when small amounts of fuel are injected. Higher levels of engine loading cause larger amounts of fuel to be injected into the same volume of air in the cylinder. Unless the volume of air is increased, the combustion process becomes progressively less complete as the amount of fuel increases. Turbocharged engines are able to compensate some¬what for increased loading and increased fuel consumption. The turbocharger acts as a compressor for the intake air, forcing a larger volume of air into the cylinders as the engine speed increases. Hence the turbocharged engine burns cleaner than a naturally aspirated engine and produces slightly less carbon monoxide (Marshall and Fleming, 1971). Much of the underground equipment used today is powered by turbocharged indirect-injection diesel engines. Although these engines emit fewer toxic contaminants than naturally aspirated engines, they do not eliminate the problem. Since the turbocharger is driven by the exhaust gases, rapid accelerations can cause temporary overfueling of the engine until the turbocharger attains a speed sufficient to restore the correct air-to-fuel ratio. During this "turbocharger lag," the combustion cylinders contain insufficient oxygen, causing severe smoking and an increased output of carbon monoxide.

Jan 1, 1982

By M J. Kindley

The Golden Cross Gold Mine Project is now fully operational and into its second year of operation. Because of its location in the sensitive Coromandel Peninsula , strict water management and environmental requirements had to be met. This led to the development of new technologies for cyanide recovery and the adoption of advanced water management and water treatment systems. This paper discusses the water management and treatment system adopted for contaminated water at Golden Cross and provides data on the operational history to date.

Jan 1, 1993

By Hans Prem

There has been a dramatic development in the field of magnetic materials in the last 10 to 15 years. Capacity improvement of electronic components especially required an increased production of "rare earth magnets", e.g. samarium-cobalt (SmCo) magnets and neodymium-iron-boron (Nd-Fe-B) magnets. We participated in this development and learned how to construct systems for the dry processing of these magnet materials. In the meantime we have supplied a large number of these systems for coarse and fine milling. Processing is effected in a protective atmosphere in order to avoid oxidation and thus deterioration of the magnet materials.

Jan 1, 1992

Ore samples generally require preparation before analysis. Serious problems can occur with contamination degradation and particle size effects. Both grinding element contammation and sample cross contamination havebeen bound to be related to sample hardness and operator technique. For best results with minerals relevant to the steel industry, the use of Siebtechnik-type mills required a combination of careful planning, short grinding periods and intermediate sieving of the sample. The results may be extended to most mineral, rock, and refractory sample preparabons.

Jan 1, 1978

By Edward C. Heistermann

The Falkirk Mining Company, a wholly owned subsidiary of The North American Coal Corporation, is located 80 kilometers (50 miles) north of Bismarck, North Dakota. Falkirk is under contract to provide 5.08 mil- lion tonnes (5.6 million short tons) annually to the Coal Creek Generating Station, an 1100 mega- watt electric plant owned by the Cooperative and United Power Associations of Minnesota. Coal Creek is located 2.4 kilometers (1 ½ miles) south of the Mine. Electricity from the plant is transmitted to rural electric customers in Minnesota via a 400-kilovolt D.C. power line.

Jan 1, 1982

Since the beginning of the 20th century the world has been trying to find a new political system, even as it did at the end of the 18th century. The French Revolution instigated the destruction of absolute monarchies when Napoleon unwittingly showed the masses the advantages of freedom, as opposed to the abuses of unlimited power by the imperialists. In spite of advances in culture, science, and technology during the past 50 years, there is a hangover of laissez-faire economic principles. Failure to divert the trends of minority pressure groups has caused two world wars and is the basis for the current social unrest and turmoil. In the ebullition of ideas there have risen to the surface the dregs of ideas, old and new-Nazism, Fascism, Russian Communism-a hodgepodge of imperialistic, socialistic, communistic and capitalistic maneuverings where state monopoly of capital enables ruthless exploitation of the masses. The United States owes much of its industrial greatness to the work of pioneers in the mineral industries. The task of the pioneer was to locate and develop in a rude way the mineral resources of the nation. Today, mineral industries leaders are still in great demand, but for a different purpose-to direct intelligent utilization of the limited, waning, submarginal mineral resources. Today the need is for trained earth scientists, mineral

Jan 1, 1950