Search Documents

By Donald R. East

The impacts of the economic storage or disposal of mill tailing wastes are becoming more important to the mining industry as environmental regulations become more demanding. Mill tailings have long been considered the stepchild of the extraction process and have not, until recent years, been treated as a separate entity of the mining and milling process with distinct and complex physical and chemical characteristics. As a waste product, the economic value of mill tailing is usually very small whilst economic and the environmental liabilities can significant. be Disposal of tailing is commonly identified as the single most important source of environmental impact for many mining projects.

Jan 1, 1990

By Tim Edwards, Richard Triglavcanin, Ian Arbuthnot, Darren Colwell, Brad Garraway, Ken Roberts

"In the mineral processing industries, there is an increasing need to design thickeners which are able to produce high density underflows usually referred to as “paste”.The behaviour of a flocculated suspension in compression needs to be well understood in order to arrive at a reliable thickener tank configuration (i.e. diameter, cone angle and depth) for a required paste result.As a suspension approaches paste consistency, it’s fluid characteristics change markedly. It develops a high yield stress, and may have an increased tendency to form agglomerates, which lead to a phenomenon known as “rotating beds”, “donuts”, or “islands”. These characteristics present challenges to the designer of the rake mechanism.The subject paper addresses the requirements for designing a paste thickener, covering the following topics:o Testwork for thickener sizingo Design of rake mechanismso Suspension rheology and effect on designo Case studiesTESTWORK AND SIZING FOR PASTE THICKENERSThickening slurries to the maximum possible density (paste) is becoming increasingly common. Applications such as Autoclave feed thickeners, paste backfill and some counter current washing (CCD) circuits are all examples of potential paste thickening applications. The principle of paste thickeners is that the compression zone is much deeper than on either high rate (HRT) or high compression (HCT) units; generally 3 metres or more. As the compression zone gets deeper, theunderflow density for a given flux rate (tph/m2) increases, as a result of two factors:1. Longer bed settling time. Settling flocs move relative to one another and release interstitial fluid when they are in compression. Increasing bed residence time achieves higher density underflow as more fluid is removed.2. The nett weight of the bed creates a compressive force on the settling flocs. This force increases with depth, so that the flocs at the bottom of the bed experience the highest compressive force. This represents the driving force to expel interstitial fluid and hence increase bed density."

Jan 1, 2005

By Bruce Hern

The last 10 years have seen a dramatic increase in the requirements for product coal quality control. This has led to electric utility sulfur scrubbing, metallurgical blast furnace optimization and coal producer blend and yield optimization. To achieve this improved level of control, coal producers are designing facilities that emphasize new technology. New facilities will be designed and existing facilities will be retrofitted with state-of-the-art technology to meet quality control standards that are dictated by the market. The first step in designing for process control requires the identification of those parameters to be controlled and the upsets that can cause variances in the final shipped product quality. The most common parameters that require control are the surface moisture (%), ash (%), pyritic sulfur (%) and gross calorific value (Btu). Total moisture is that moisture that exists on the surface of the particle and is inherent in the particle itself. For the purposes of control, the total moisture is monitored, while surface moisture is controlled. Ash is the inorganic residue remaining after all other constituents are burned away at 75O°C( 1382°F)(ASTM, 1992). Sulfur is the amount of total sulfur that exists either as pyrite (FeS2), inorganic sulfate (FeS04), or organic sulfates (C4H4S) (Leonard, 1979). Currently, pyrite is controlled and total sulfur is monitored. The gross calorific value is the amount of heat produced when a unit quantity of coal is ignited under specified conditions. In this case, a l-g (0.03-oz.) sample of coal is ignited in an isoperibol waterbath and the temperature rise of the water bath is observed. The moisture and ash-free (MAF) Btu is relatively constant for a given seam, resulting in the whole calorific value being a function of the moisture and ash levels (Leonard, 1979).

Jan 1, 1994

By E. V. Given

Designing a tailing dam is a major step toward fully integrated mill operation. In the case of large concentrators considerable planning is necessary, and the site of the tailing disposal area may very well dictate the location of the concentrator itself. Before a suitable location can be selected several pertinent factors should be investigated: estimated life expectancy of the mine and, if possible, approximate total tonnage; knowledge of daily mill capacity; and the possibility of future mill expansion. In addition, the area should be able to store tailing for many years and, from a cost and maintenance stand- point, gravity flow will probably be desired.

Jan 7, 1959

Research has determined that ground control interaction problems in mining over a previously mined seam occur primarily in the tension zone created at the edge of the subsidence trough, and in areas above lower seam remnant pillars. Based on empirical and analytical studies, planning options for improving conditions on the upper seam have been developed to optimize extraction while minimizing the negative effects of seam interactions. These options include prediction of potential upper seam damage, guidelines for minimizing inevitable negative interaction effects, and recommended opening and pillar sizes, shape, and orientations, as well as design and planning procedures.

Jan 1, 1988

Historically, the selection of mining sequence for multiple seam conditions has been based on many factors other than ground control considerations and minimization of interaction effects. Today, numerous operations are finding themselves mining above existing or abandoned operations, some of which exhibit large scale caving, pressure arches and subsidence troughs. Development of design criteria for the upper seam that would alleviate damage due to lower seam interaction effects can contribute substantially to the safety and productivity of many mining operations. The primary objective of this re search has been to identify methods of improving ground control conditions in the upper seam when mining through either passive or active subsidence waves. These methods concentrate on improved ground control practices for the upper seam, rather than reducing the amount of subsidence in the upper seams by improved practices in the lower seam. Design factors such as pillar size, pillar and opening orientation relative to the subsidence trough, offsetting intersections, and different support methods have been studied for the upper seam in a variety of typical geologic environments. Analysis has demonstrated criteria for ameliorating negative interaction effects and facillitating design in the superincumbent seam.

Jan 1, 1986

By Sam Spearing

Free-standing supports are commonly used in coal mines in the USA, particularly when longwalling. A recent trend has been the development of prop supports. Prop supports have many advantages over bulky, crib-type secondary standing supports, particularly in regard to material handling and installation. The challenge in prop design has been to develop load capacities that can compete with crib type systems and to develop reliable (stable) yielding capability. This paper will focus on the design aspects of steel prop supports, specifically, and evaluate the various concepts that have been developed to provide easy height adjustment and sustainable stable yielding under load. The design and resulting improvement provided by recent support developments called the Quik Stik and Ball Buster are discussed in detail. Performance areas that still need improvement in the design and usage of free standing supports in general are identified and possible solutions outlined.

Jan 1, 2008

By R Ahola, M D. Henschel, M A. McParland

With the introduction in recent years of third-generation interferometric synthetic aperture radar (InSAR) techniques, monitoring of mine slopes, benches and surrounding areas has benefitted from increased accuracy and coverage. Fundamental research into point and distributed scattering techniques has pushed the use of InSAR to provide higher spatial and height resolution. In this paper we discuss the operationalisation of third-generation InSAR techniques and show its application to active mining operations.This paper will discuss the use of multiple independent measurements of ground movement obtained from operationally-derived InSAR products over a wide variety of deformation areas within an active open pit mining operation (ie pit slopes, dewatering depressions, tailings containment and waste dumps). A technique that shortens the time between observations (increased observation frequency) and provides ongoing estimates of measurement accuracy will be described. The methodology exploits available satellite data by using multiple satellites and multiple beams. The paper will also examine factors in the design of a mine survey with third-generation InSAR and illustrate some of the necessary engineering trade-offs to efficiently monitor a mine from space.Overall, this paper aims to demonstrate the capabilities and advantages of operational third-generation InSAR techniques for ground movement monitoring of mining operations and provide a framework for proper design of a mine InSAR survey.CITATION:Henschel, M D, Sato, S, Ahola, R and McParland, M A, 2014. Designing interferometric synthetic aperture radar surveys for mine monitoring with accuracy assessment, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 233–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By N. C. Karmakar, Y. V. Rao, M. Aruna

No one can properly work without sufficient light and this is especially so in mines where conditions are difficult. Artificial lighting is very important for the night shift to provide a safe and efficient working environment, which must be evenly illuminated with no obvious dark spaces and a minimum amount of glare. During an illumination survey of a large mechanized surface mine, it was found that the illumination level varied and was not uniform throughout the length of the road; it was high at one side of the road instead of at the centre. There were also different combinations of lamps, with angles of light arm varying from 35º to 70º. In this respect, an experimental study was carried out with a fabricated telescopic light pole to uncover the optimum design parameters of lighting installations. The analysis was done by plotting isolux contours for fixed installations and drawing graphs for various combinations of luminaries, reflectors, light arm angles, and height of lanterns by plotting the horizontal angle of the light arm along the abscissa, and the contour area along the ordinate. The study revealed that the design parameters of the lantern are mainly dependent on the type of luminaires. It was revealed that the pot reflector with a combination of tubular bulbs produces a wide distribution of light, and contributes towards a reduction of luminaries when installed in longer roads.

Jan 1, 2005

By T. V. Ramey

Heap leaching in certain parts of the world, such as Chile's Atacama Desert, brings unique design problems in the form of possible large differential settlements of the foundation soils due to the dissolution of salts in northern Chile the soils often contain very high concentrations of soluble salts (nitrates, potassium, magnesium, and common sodium). When a leak in the liner occurs, the escaping solution dissolves these salts and triggers differential settlement. If the settlement is great enough, the geo-membrane tears, the leakage increases, triggering more differential settlement. The nitrate plants have experienced many occurrences of this phenomenon where a brine pond will undergo a sudden and complete loss of the impounded liquors. The authors present a simplified technique to quantify the differential settlement resulting from dissolution and provide a method which can be used to select a geo-membrane with suitable flexibility under axi-symmetric (multi-axial) load conditions to tolerate the predicted settlement. (This paper was previously published for Randol Gold Forum 1996 [Ref. 6]).

Jan 1, 1997

By Marc E. Orman, Todd V. Ramey, Mark E. Smith

Heap leaching in certain parts of the world, such as Chile's Atacama Desert, brings unique design problems in the form of possible large differential settlements of the foundation soils due to the dissolution of salts. In northern Chile the soils often c?ntain very high concentrations of soluble salts (nitrates, potas­smm, magnesium, and common sodium). When a leak in the liner occurs, the escaping solution dissolves these salts and trig­gers differential settlement. If the settlement is great enough, the geomembrane tears, the leakage increases, triggering more dif­ferential settlement. The nitrate plants have experienced many occurrences of this phenomenon where a brine pond will under­go a sudden and complete loss of the impounded liquors. The authors present a simplified technique to quantify the differential settlement resulting from dissolution and provide a method which can be used to select a geomembrane with suit­able flexibility under axi-symmetric (multi-axial) load condi­tions to tolerate the predicted settlement.

Jan 1, 1996

By S. Banisi, A. Haji-Zadeh, A. R. Hasankhoei, M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9m × 2.05m AG (Autogenous) mills (fixed speed) are used in parallel in a dry operation. The test works conducted in a scale down mill with a diameter of 1m indicated that conventionally used "deflector" type liners did not provide efficient environment for grinding. In this research, to improve the grinding efficiency, a new design using low profile end liners incorporating radial ribs of proper height was investigated. In order to determine an appropriate liner design at different operating conditions, a 100cm×10.8cm model mill was used for experimentation. The special design of model mill made it possible to increase the radial ribs height in steps of 6mm up to 18.5mm. The transparent end of the mill enabled accurate trajectory determination by image analysis. The results indicated that the new lower height profile deflectors and 15.5mm-height (14.5cm in industrial scale) radial ribs improved the mill performance while avoiding excessive pressure drop across the mill and wear on the liner. The image analysis showed that the use of new liners increased the distribution of coarse particles across the mill cross section from 28% to 35%. A new liner design was proposed by decreasing the number of liners in each slice from 5 to 4 pieces. The thickness of the inner head liners reduced from 45cm to 30cm and the outer deflector liners replaced by radial ribs. The distance between the feed and discharge inner head liners increased from the original 115cm to 145cm which increased the effective length of the mill by 26%. The new design reduced the weight and volume of end liners by 9% and 23%, respectively. It was predicted that the new liners design increases the mill throughput by 10% and reduces the metal consumption by 20%.

Jan 1, 2016

By Binxu Zeng, Mark Jolly, Xiaojun Dai

"The traditional investment casting foundries use batch melting and chunky running systems to produce casting components. This method leaves the energy saving issue as subsidiary one. In our research project, one of the partners, the AEROMET international PLC provides the thin wall aluminium component ""filter housing"" for test. The AERO MET uses traditional casting route to produce the filter housing, which only gives 5% --10% yield. In this paper, numerical simulation method is used to analyse filling and solidification of the casting running system. The CRIMSON running system of the filter housing is designed by using casting simulation software, MAGMAS and Flow3D. By working with AEROMET, various configurations of the casting running systems were tested and analysed. Using them ultiple life cycle approach, the energy content of new process is compared with traditional one. It indicates that the CRIMSON process only uses 36% of energy consumed by the traditional route.IntroductionThe investrnent casting is a metal for ming process using expendable patterns, which is a standard casting technique and is widely used to produce quality parts. Its accuracy, versatility and integrity tie itself to important and precious engineering components in Aerospace industry. However, traditional investrnent casting process usually uses chunky runner system and gravity filling method. It not only reduces the casting yield of the product but also causes the pouring defect during the casting. As author's previous research showed that gravity filling method pouring basin and down sprue are two main resources of entraimnent defects generation. No matter how good the running system is, entraimnent defects such as double oxide films (DOF) and bubbles will I get into the casting to cause problem."

Jan 1, 2013

By N. Jovanovic, A. Vazirizadeh

"The main objective of this study is to find a solution to design a mass flow observer system with the minimum required sensors and maximum observability for a mineral processing plant. The second objective is designing a mass flow observer configuration with high reliability to manage sensor failures. This configuration will provide a robust monitoring system that increases plant availability and process measurement fault detection. Furthermore, the monitoring system is expected to improve process efficiency. In this investigation, the procedure of designing an observer system is presented along with three models to design the sensor network. The advantages and disadvantages of each models are discussed and finally the models result for an industrial case are presented and analyzed. INTRODUCTION The concepts of observability and redundancy of mass flow are directly linked with the ability to solve and estimate the mass flow. There are hundreds of streams in a process plant flowsheet, and for technical and economic reasons it is not possible to measure all mass flows. It is thus important to know for a set of measured streams, which of the unmeasured streams can be estimated. The concept of observability deals with this issue. It is also valuable to know whether a measured mass flow of streams can be estimated even if a sensor fails for some reason. Redundancy deals with this failure question. A stream is said to be observable if it can be estimated by using the measurements and/ or mass conservation equations. Also, a stream is redundant if it is observable even when its measurement is removed. Observability and redundancy analysis can be exploited for adding new measuring instruments. It can also play a useful role in efficient decomposition and data reconciliation problem (Narasimhan and Jordache 1999). The value of an observer system cannot be justified without considering its benefits. This justification is done through evaluation of data reconciliation, gross error detection and improving process performance such as outlined below:"

Jan 1, 2018

By P Cheluszka, M Jaszczuk, P Sobota

This paper refers to a new idea of stereometry of cutting drums of longwall shearers designed to get medium and hard to mine coals. A new way to place picks on a drum enables to readjust a number of picks being in contact with the body of coal to shearer haulage speed. Owing to this a remarkable increase in depth of a cut within the low range of haulage speed has been obtained. On comparing operating characteristics a considerable reduction in the specific energy consumption has been shown when using the units machined as per the new idea, in comparison with the units produced in series.

Jan 1, 2003

By Jamal Jafari, Abbas Sam

"The concentration of the fourth production line at Golgohar includes 66% iron with Blaine number of 500 cm2/g. For pelletizing process, the feed iron grade should be greater than 68% with minimum Blaine number of 1800 cm2/g. In this study, the low intensity magnetic Separators, particularly the feed particle size distribution of LIMS were considered. The feed particle size distribution of the separators was optimized to prepare an appropriate concentrate (as mill pelletizing feed). The samples were performed from the LIMS feed and after grinding, four d80 (64, 103, 132, and 15 3µm) were prepared. Then, laboratory magnetic separation experiments were conducted on these samples. The best results obtained using d80 of 132µm. In this particle fraction, the iron grade and Blaine number were 70.3% and 1571 cm2/g, respectively. Therefore, it seems necessary to include a grinding and classification systems before LIMS stage. According to the presence of a high amount of -132 µm particles in the initial feed, an inverse closed circuit was selected. The hydrocyclone was designed in three units as the classification system with 62 cm (diameter), 22 cm (overflow outlet) and 11 cm (apex diameter). By simulation of hydrocyclone with USIMPAC software, the size distribution of underflow was determined. Based on these results, a ball mill with dimensions of 6.7 m (length) and 5 m (diameter) was designed as grinding system.INTRODUCTIONGole-Gohar iron ore concentration plant No.4 (Polycom Plant) in Gole-Gohar Industrial and Mining Complex was installed to increase production capacity as well as treating the circulating load from AG and SAG mills of the main concentration plant of the complex. The load from the mine is crushed using jaw and cone crushers. The crushed ore is then combined with the circulated load and the combination is then grounded using HPGR and ball mills respectively.After comminution, there is a magnetic separation plant which includes a medium intensity magnetic separator (MIMS) followed by three low intensity magnetic separators (LIMS). Final concentrate dewatering is done using three belt filters. After the primary magnetic separation, the ore is upgraded to 62% Fe content and final concentrate which is the product of LIMS has 66% Fe content."

Jan 1, 2016

By Frank M. Stephens, Robert D. Macdonald

As processes for handling low-grade or complex ores become more complicated and as new methods are found, the need arises for more complete and detailed pilot-plant studies to protect the capital investment required for a full-scale plant. Occasionally a process is firm technically, but there is a need for a demonstration plant that will convince nontechnical men of the wisdom of investing in a full-scale operation.

Jan 5, 1959

By Andy Judge

"In traditional Permanent Magnet Machines, such as electric motors and generators, power is transmitted by magnetic flux passing through an air gap, which has a very low magnetic permeability, limiting performance. However, reducing the air gap through traditional means carries risks in manufacturing, with tight tolerances and associated costs, and reliability, with thermal and dynamic effects requiring adequate clearance. Using a magnetically permeable, high thermal conductivity material has the potential to improve magnetic performance, while at the same time offering performance advantages in heat transfer.Ferrofluids can be used to improve permeability in the rotor I stator gap. However, there are several tradeoffs in this approach. Fluid immersion comes with an increase in fluid friction loss compared to the windage losses of a traditional system. Isolating the rotating components from the ferrofluid can offset this effect. Also, while the magnetic effect can be positive for gap permeability, leakage flux can increase, and saturation can limit gains. These effects must be taken into account for a system optimized for ferrofluid immersion.IntroductionPermanent Magnet Machines (PMM's) convert electrical energy to mechanical energy in motor applications, or, for generator applications, convert mechanical energy to electrical energy through means of passing alternately polarized magnets past electrical coils. Looking at a simplified version of a PMM, where Rx is magnetic reluctance and <l>x is magnetic flux, we have the circuit shown in Figure 1."

Jan 1, 2013

By H G. Poulos

"This paper sets out a simplified approach by which the practical foundation designer can undertake the relevant calculations to satisfy the requirements for deep foundation design in seismic areas. The following matters are dealt with:a. Design issues that should be addressed;b. Pile design for axial loading, including the possible effects of liquefaction;c. Pile design for lateral loading where liquefaction does not occur;d. Pile design for lateral loading where liquefaction does occur;e. Measures to mitigate against liquefaction effects.The paper is a modified version of a paper presented in 2013 to the 19th NZGS GeotechnicalSymposium, Queenstown, New Zealand.1. INTRODUCTIONConsideration of the effects of earthquakes and seismic loadings is an increasingly important aspect of modern foundation design, and most contemporary standards have a mandatory requirement for such consideration. For example, the Australian Piling Code, AS 2159-2009, states that “a pile shall be designed for adequate strength, stiffness and ductility under load combinations including earthquake design actions”. However, the methods by which such considerations can be undertaken are generally not set out in the standards, and many approaches have been utilized, ranging from very simplistic methods to extremely complex computer analyses. Accordingly, there appears to be scope for an approach that is soundly based but which is neither too simplistic nor too complex.Poulos (1989) has suggested that there are three categories of analysis and design, as follows:1. Category 1: empirical methods.2. Category 2: simplified but soundly-based methods.3. Category 3: more comprehensive methods that are soundly-based, and site-specific.The objective of this paper is to set out a systematic but simplified approach which falls into Category 2 above, and by which the foundation designer can undertake the relevant analyses to satisfy the foundation design requirements for seismic regions. Emphasis is placed on methods that do not require “black box” software or which employ complex soil models in which the physical meaning of the parameters is unclear."

Jan 1, 1900

With the continued implementation of stricter limitations on the discharge of excess process water from all existing and future mining and metallurgical operations, the design and operation of the entire process water circuit must form an integral part of any total operational package. It is far better to æanticipate and circumvent the problemÆ rather than be forced into an expensive remediation program after the event. By far the greatest problem relates to the treatment and disposal of what is generically known as acid drainage. In simple terms, an acidic metal sulfate solution is generated by a series of chemical and biological reactions as soon as most sulfide minerals are exposed to air and water. Treatment of this solution by one or more of a wide range of chemical and physical options can involve substantial capital and operating costs, although there are recent processing options that yield saleable by-products, thereby reducing the financial liability of what is effectively a waste stream. This presentation provides an overview of the Australian situation compared with the rest of the world and outlines the basic features of a number of the more advanced passive and active acid drainage options.

Jan 1, 2004