Search Documents

By Kevin C. Milne

"The solution of problems associated with development of a sour gas reserve will be of increasing importance in tl1e next few years if gas export is approved •by the National Energy Board. The purpose of this paper is to review briefly the history of the Carstairs gas field, and tCI describe in a general manner the reservoir, and the producing and processing facilities.HISTORYThe Carstairs gas field was discovered in April 1958 when the discovery well, Home Carstairs 10-17, was successfully completed as a gas well in the Elkton member of the Turner Valley formation. Geo-graphic location of the field is shown in Figure No. 1. Note that the field is about five miles west of the town of Carstairs, Alberta, which in turn is about 40 miles north of Calgary. Drilling subsequent to the discovery well resulted in three addition-al producing wells and one dry hole during I.958; two producing wells during 1959; and one producing well and one dry hole during 1960. Thus, seven producing wells and two dry holes have been drilled in the Carstairs field to date.In November 1959 a 12-section block in the Carstairs field was unitized on a surface acre basis. Mean-while, in June 1959, operators in the field executed an ""Interim Plant Agreement"" that provided the money needed to start construction of a joint venture processing plant and gathering system. Construction of the plant and gathering system was completed in February 1960."

Jan 1, 1960

By F. W. Bremmer

THE drilling of constantly deeper oil wells has made it imperative that the manufacturer of casing be ever searching for new methods and new materials to meet the increased demands. One phase of this search constitutes the subject matter of the present paper. Starting from the original Drake well in 1859, the depth of wells has advanced by leaps and bounds, until today depths of 6000 to 8000 ft. are common. Conditions point to the necessity for drilling to greater depths, and it is not at all improbable that much of the future oil produc- FIG. 1.-TREND IN DEPTH OF OIL WELLS. tion will be from, wells around 10,000 ft. deep. The trend to deeper wells is nicely illustrated by the curve in Fig. 1.1 The points plotted are the maximum depths attained in the various pools which were at their peak for the years given. It may be of some interest to observe the change that has taken place in the tensile and collapsing stresses over the last 25 years. The pressure at the bottom of a 900-ft. hole, equivalent to the pressure caused by an equal column of water, is only 450 lb. per sq. in. The equivalent

Jan 1, 1930

By P. A. Crane, N. Shirley, Aung Moe, H. M. Nicholson, D. Kan

Kazakhstan’s first commercial copper-leach solvent extraction-electrowinning plant, Central Asia Metals’ Kounrad project, was commissioned in April 2012. Exploiting low grade waste stockpiles produced during Soviet era open pit mining, a 10,000 tpa copper cathode plant was designed, constructed and commissioned within 18 months. Overcoming initial challenges with a workforce unfamiliar with the technology and with extensive periods of sub-zero conditions during winter the project has consistently met targets and produced high quality copper cathodes at cash costs of less than US$1/lb. Challenges encountered during the first two years of operation are described and future plans briefly discussed.

Jan 1, 2014

By H. B. Lumsden

This paper is intended to deal merely with the commercial development of some of the principal non-metallic mineral resources in the three prairie provinces- Manitoba, Saskatchewan, and Alberta. Coal is not included in this summary. Building Stone First and foremost, mention may be made of the building stone now being produced at Tyndall, Manitoba. This is a mottled limestone and is declared by experts to be one of the finest building stones in America, both as regards durability and appearance. It has been used very extensively both for exterior and interior work, not only in western Canada, but also in the principal cities as far east as Montreal. The stone is the "'Upper Mottled Limestone", which forms the summit of the Trenton (Ordovician) strata in the Lake Winnipeg basin. Quarries are at present being operated at Garson and Tyndall . The area where this stone is known to be available extends in a north and south direction for a distance of three miles, and the main productive ridge is probably about one half mile wide. The outlook for the future of the industry is extremely promising, as the stone is becoming increasingly popular in Eastern Canada, more particularly for interior work.

Jan 1, 1928

By Minoru Kawamura, Shinya Tanaka

In Japan, a cartridged emulsion explosive is generally used for tunneling. The workers are compelled to approach the face on charging the explosives into the drill hole with the tamping rod. Therefore, the workers are exposed to the risk of the disaster with the cave-in and the falling rock. The mechanization of the tunnel work has been advancing gradually. Especially, the development of the mechanization for charging work is desired in order to avoid the risk of disaster on workers. Recently, some charging machines such as the bulk emulsion explosives have been evaluated. However, a universal method has not been established yet, because the evaluated machines were not adequately suited from the point of the regulations and the consumption style of explosives.

Jan 1, 2008

By J. A. Chermak, D. D. Runnells

Sulfide-bearing waste rock, ore and tailings have the potential for generating acid rock drainage (ARD) when exposed to an oxidizing environment. The possibility exists of utilizing the acid produced to react with lime and/or limestone to form a self-sealing cap on the reactive waste rock and tailings. Laboratory column experiments were conducted using acid-generating waste rock with a surface amendment of limestone and/or lime. Artificial rainwater was introduced and allowed to drain through the columns. Results demonstrated that the limestone and lime reacted with the acidic rock, resulting in the precipitation of a hardpan layer of gypsum and amorphous iron oxyhydroxide at the surface. The hardpan layer significantly reduced the effective permeability of the column. Based on the results of this study, it should be possible to create hardpan layers as chemical caps to significantly reduce the infiltration of rainwater and snowmelt into acidic waste rock or tailings material in the field. Unlike traditional capping methods, e.g., clay and high-density polyethylene (HDPE) covers, chemical caps should be self-healing.

Jan 1, 1998

By J. A. Chermak

Piles of sulfide-bearing overburden, ore, and tailings have the potential to generate acid drainage (AD) when exposed to an oxidizing environment. Laboratory column experiments were conducted using acid-generating overburden material with an added surface amendment of limestone and/or lime. Artificial rainwater was introduced and allowed to drain through the columns. Results showed that the limestone and/or lime reacted with the acidic rock, resulting in the precipitation of a hardpan layer of gypsum and amorphous iron oxy-hydroxide at the surface. The hardpan layer significantly reduced the effective permeability of the column. Based on this study, hardpan layers can be created as chemical caps to significantly reduce the infiltration of rainwater and snowmelt into acidic overburden or tailings material. Unlike traditional capping methods (for example, clay and high density polyethylene (HDPE) covers), chemical caps are self-healing.

Jan 1, 1996

By Ying-Chu Hoh, Renato G. Bautista

The chemically based models previously developed to describe and predict the distribution coefficients and separation factors for several different single and multicomponent metal extraction systems are presented in a more general form in this paper. The degree of formation of the aqueous phase inorganic metal complexes, the extraction mechanism of the complexes, and the equilibrium constant for the extraction reaction are used in the development of the models. The concept has been successfully applied to extraction systems where the organic solvent extracts an ionic species and where the organic solvent extracts only the neutral species. In addition, a model to describe a system where the organic solvent is extracting several extractable species has been derived on the same basis

Jan 1, 1981

By Frank L. Peterson

This paper deals with problems of groundwater development in an insular circum-Pacific environment, and is not oriented as such to mining and mineral development. Nonetheless, because a reliable water supply is necessary for most mining and related support activities, and since water supplies are limited in many insular parts of the Pacific Basin, groundwater development is a subject which must be frequently addressed. Because many in the audience may be already familiar with groundwater development for continental environments, I have chosen to deal with groundwater occurrence and development problems which for the most part are unique to insular environments. In such environments, the local geology plays a critical role in determining groundwater occurrence and its suitability for development. The three examples discussed in this paper-Hawaii, Guam, and the Marshall Islands-were selected because they illustrate groundwater occurrence in a wide range of geologic conditions. For example, the Hawaiian aquifers consist primarily of basaltic lavas, while Guam is made up of andesitic lavas and coral reef limestones, and the Marshall Islands are coral atoll deposits. Despite differences in aquifer size and rock types, the principal mode of groundwater occurrence at the three sites is similar; thus, development strategies are also similar. Figure 1 shows the location of the three sites.

Jan 1, 1982

By Biao Qiu

Longwall and/or room-and-pillar mining operations in multiple coal seams could not only induce subsurface and surface subsidence but also cause interactions between these mined coal seams. The interaction might destabilize mine structures and subsequently induce additional strata movements. Mechanical models to utilize the predicted subsurface deformations to assess the interactions and the consequences have been developed. The models are incorporated into a computer program, CISPM-MS, for predicting the final surface movements and deformations as well as the mining interactions associated with multi-seam coal mining operations. It predicts final surface movements and deformations caused by the individual mining operations and by the interactive effects. The program can also be used to assess mine structural stability in multi-seam mining operations. The paper presents the developed interaction models and their application in surface subsidence prediction caused by multi-seam mining operations. A case study involving mining in two coal seams, using longwall and room-and-pillar mining methods, respectively, will be used to validate the program.

Jan 1, 2013

By B. Qiu, Y. Luo

Longwall and/or room-and-pillar mining operations in multiple coal seams may not only induce subsurface and surface subsidence but also cause interactions between these mined coal seams. The interaction might destabilize underground mine structures and subsequently induce additional strata movements. Mathematical models to use the predicted subsurface deformations to assess the interactions and the consequences have been developed. The models are incorporated into a computer program, CISPM-MS, for predicting the final surface movements and deformations, as well as the mining interactions associated with multiseam coal mining operations. It predicts final surface movements and deformations caused by the individual mining operations and by the interactive effects. The program can also be used to assess mine structural stability in multiseam mining operations. The paper presents the developed interaction models and their application in surface subsidence prediction caused by multiseam mining operations. A case study involving mining in two coal seams, using longwall and room-and-pillar mining methods, respectively, will be used to validate the program.

Jan 1, 2013

By A Lechner, T Baumgartl, S Arnold, P Audet

When revegetation is a part of a rehabilitation strategy at mine sites in arid and semi-arid environments, its success can be strongly affected by the availability of water prior or during the time of seed dormancy, germination and early growth of seedlings. The semi-arid and arid environments of northern Australia are characterised by highly variable and erratic rainfall and hence the actual weather conditions at and around the time of germination and seedling emergence play a critical role in determining the success of plant establishment and the type of plant community that may develop.Using available climate data, an analysis has been undertaken and a set of indices has been developed which describe the suitability of the climatic conditions for rehabilitation. In total, eight sites from Queensland and one site from New South Wales, Australia have been analysed. It could be determined that regular rainfall and relatively short periods of water-deficit are key characteristics of climate suitability. A comparison of the locations studied allowed the separation into suitable and susceptible locations in terms of the availability of water, amount of rain and duration of drought between rain events.In our experience, specific estimates of climate suitability are rarely incorporated into the design of mined land rehabilitation programs. We consider that the regional intensity, seasonality and extremity of climate represent an overarching component of landscape complexity, which in turn will influence the development of post-disturbance ecosystems in these regions. This paper presents the outcome of climate analyses paired with the development of suitability indices. A conceptual framework is presented explaining the suitability matrix and its incorporation as a prognosis tool to achieve greater certainty for success in rehabilitation development.CITATION:Baumgartl, T, Arnold, S, Audet, P and Lechner, A, 2014. Development of climate-based suitability indices for the improvement of success in rehabilitation, in Proceedings Life-of-Mine 2014 , pp 483–490 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By A. Peppas

Perlite is a naturally occurring siliceous rock, which can be expanded from four to twenty times its original volume when heated at a temperature close to its softening point. The expanded perlite is characterized by increased sound and thermal insulating properties. However, the conventionally expanded perlite products have high porosity and low mechanical properties that limit the range of their applications in the construction and chemical industry. The present work aims at the development of new closed porous microcellular material from perlite with enhanced mechanical and physical properties to be applied in new applications, like joint compounds, functional fillers for special paint types, special blasters and mortars, artificial marble. For the production of these new materials a vertical electrically heated furnace with six different heating zones and controlled gradient temperature profile was used. The effect of major process parameters, like temperature and air flow, on the quality of the produced materials was studied using Greek perlite from Milos Island. The quality of the new products was evaluated in terms of their bulk density, compression strength, water and oil absorption, surface area and pore volume. The experimental results show that the produced materials are characterised by improved mechanical and physical properties compared to the conventionally expanded perlite products.

Jan 1, 2006

By Cam T. Nhan

The potential use of coal fly ash as a construction material has been recognized for many years,. In this work, an admixture of the ash residue is investigated for use as a landfill liner. In particular, its performance as a chemical barrier to the leachate from the municipal solid waste (MSW,) is determined. The test specimens are a water compacted admixture of class F fly ash, low in calcium content, which is blended with lime dust and calcium bentonite. MSW is passed through the compacted fly ash specimens under a gravitational head. The. diffusion of elements in the leachate through this material is monitored as a function of time. The distribution profiles of the retained elements in the compacted admixture provide prediction of the long term performance of the compacted admixture directly affect the leachate diffusion rate, hence, the mobilities of the retained elements.

Jan 1, 1992

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This article focuses on U.S. Bureau of Mines (USBM) and National Institute for Occupational Safety and Health (NIOSH) research to examine factors that had a significant influence on mine face ventilation design during the past century. Several "milestone" events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative face ventilation designs and a consistent commitment to mining health and safety. Ventilation has always been a concern in underground coal mining. For many yeas, there was no appreciation of how ventilation could be used to remove harmful contaminants from the air or how to control airflow quantities. The first known problems with ventilation date back to the 14th century, when it was recognized that lack of air was a major impediment to the expansion of mines. The common method of solving ventilation problems at that time was to abandon the existing mine and start a new one nearby. Ventilation in the early days of coal mining was accomplished by means of a natural draft, created principally by a difference in the weights of columns of air between the intake and return openings. Later, in the 18th and 19th centuries, a furnace was introduced underground to increase the updraft in the return shaft. This allowed for a larger quantity of air in circulation. When mines went deeper and became larger, mechanical ventilation became necessary and was first accomplished by steam-driven fans. These fans became more prevalent as furnaces were prohibited in underground mines, especially after the Avondale disaster in Pennsylvania in 1869 (Roy, 1876). Eventually, these fans were replaced by more powerful, electrically [ ]

By J. N. Van der Merwe, M. Mathey

"The development and mechanical characterization of coal-crete, a composite material generated from coal fragments and some binder material, is described in this paper. Coal debris was obtained from a colliery in South Africa. The binder used in the study basically consists of cement and water, and further ingredients are added to the mixtures, such as sand, fly ash and polymers, in order to investigate alterations of the mechanical properties of coal-crete.Results from over 220 mechanical tests on coal-cretes with various binder mixtures give consistent trends for the material’s behaviour. Linear relationships are suggested between the uniaxial compressive strength, Young’s Modulus and the indirect tensile strength of the coal-crete.It is shown that mechanical properties comparable to coal can be achieved. Coal-crete is therefore suitable for physical modelling of mining situations in experimental studies and for use as backfill in underground coal mines. The latter application is particularly attractive when refuse coal is used as aggregate material. The indicated trends in this study may be used as a guideline for individual coal-crete design needs. However, some uncertainty remains as to the influence of particle shape, size and gradation, coal rank and age of the coal-crete. These aspects are recommended for further research."

Jan 1, 2015

By A. Van den Steen

In the early fifties Professor Breckpot of the Louvain University in Belgium in collaboration with the Research Laboratory of Metallurgie Hoboken, discovered the possibility to separate nickel from cobalt sulfate solutions by a nickel sulfide depolarized cementation. This reaction, completed later with a zinc precipitation, was developed into purification processes for the Shituru and Luilu Gécamines cobalt plants in Zaíre. Due to increasing demand for higher quality products and the necessity of lowering the production costs, more laboratory and pilot plant investigations concerning the key parameters for the nickel and zinc sulfides precipitation were under- taken. Especially the relative stabilities of cobalt, nickel and zinc sulfides, precipitated with elemental sulfur or sodium hydrosulfide, were examined in relatlon with the pH and with the redox potential. These investigations have led to better plant practice and new development possibilities. The valorisation of the precipitated sulfides has also been considered.

Jan 1, 1988

By S. Dwarapudi

Pelletizing of Indian chromite ores is more challenging due to their high refractory nature. High Cr/Fe ratio and high MgO content in these ores demand high firing temperatures and longer firing cycles but often result in low strength fired pellets. Aim of this study was to develop cold bonded chromite pellets for smelting in submerged arc furnace (SAF) from chromite fines using suitable binder that induce less gangue into the pellets but cures quickly. Different binders were studied through laboratory pelletizing experiments for their suitability for cold bonding the pellets. As result, a composite binder comprising organic and inorganic binding agents was found to be suitable and pellets made from the same were tested for their low and high temperature behavior. High temperature reduction studies revealed that pellets were resistant to disintegration up to 1200 °C.

Sep 1, 2012

By M. A. Bussell, G. S. Camm

The study included lode zones at Wheal Pendarves, South Crofty and Rosevale tin mines. Fluid inclusion-containing microfractures are a common feature of the granites and typically show a preferred orientation over quite a large area. The close proximity of a dominant vein or fault controls their density and orientation. They are important pathways for fluids and provide a marker for palaeo-fluid flow. Overprinting provides a reliable representation of the evolution of the hydrothermal fluids in a vein system from early magmatic fluids to late-stage meteoric and basinal brine input. Measurement of microfracture orientation allows estimation of the regional stress regime during a specific hydrothermal event. Since micro- and macro-structures can generally be reliably correlated, these studies assist in modelling the detailed development of complex vein systems. Microfracture density is a good measure of palaeo-permeability, with implications for control of wallrock alteration. The determination of the location and density of microfractures can assist the mine geologist in identifying the location of potentially economic vein structures where macroscopic markers are absent

Aug 1, 1996

By William D. Mayercheck

The introduction of continuous mining machines in the late 1940's prompted the mining industry to reassess shuttle car batch-type haulage. Between place changes, the continuous miner could cut and load coal on a nearly continuous basis, but after loading a shuttle car, the high-capacity machine had to wait until the second shuttle car came inby and spotted itself under the miner tail boom. Thus, the wait-for-shuttle-car delay periods became the new bottleneck for increased coal production from the mine section. Recent studies have shown that nearly 25 pct of the continuous miner cycle time is consumed by delays in the haulage system, usually waiting for shuttle cars. Computer simulations of a face operation indicate that up to a 45 pct increase in coal production may be realized through the use of a continuous haulage system, assuming of course that the outby haulage system can handle this increased capacity. Coincidently, there are recent claims by some mines using continuous face haulage of a production increase of 45 pct compared with shuttle car haulage. These documented production records, computer simulations, and common sense indicate the potential of continuous face haulage in underground coal. The late 1960's and early 1970's saw several mining machinery manufacturers market mobile bridge carrier and piggyback bridge conveyor continuous haulage systems for use in underground coal mines. These systems have shown limited potential in some mines and outstanding success in others. It appears that no one system can be universally applicable to all underground mining conditions; thus, the Bureau of Mines has conducted extensive research over the last few years to investigate different types of continuous haulage systems for use in high and low coal seams that will advance the state of the art.

Jan 1, 1977