Search Documents

By J Chen

Research conducted into backfill drainage at Mount Isa Mines since 1992 is described. Piping in draining backfilled stopes has been the primary cause of bulkhead failures and emphasis is placed on research into the piping mechanism. Laboratory and in situ tests aimed at understanding the piping mechanism have been conducted and the results are presented. A case history of piping in a draining bench stope fill mass is described and a technique for reducing the potential for bulkhead failures in bench stopes is presented. Hydraulic fill is produced by standard cycloning of tailings and the overflow (reject material) is sent to thickeners prior to placement in the tailings dams. Research into the partial introduction of thickener underflow into the backfill system and its influence on backfill drainage is also described.

Jan 1, 1998

By Chend J

Research conducted into backfill drainage at Mount Isa Mines since 1992 is described. Piping in draining backfilled scopes has been the primary cause of bulkhead failures and emphasis is placed on research into the piping mechanism. Laboratory and in situ tests aimed at understanding the piping mechanism have been conducted and the results are presented. A case history of piping in a draining bench scope fill mass is described and a technique for reducing the potential for bulkhead failures in hench stopes is presented. Hydraulic fill is produced by standard cycloning of tailings and the overflow (reject material) is sent to thickeners prior to placement in the tailings dams. Research into the partial introduction of thickener underflow into the backfill system and its influence on backfill drainage is also descrihed.

Jan 1, 1998

By David Hake, David Salisbury

The Drainage Services Department (DSD) of the Hong Kong SAR Government commissioned the design and construction of the West Kowloon Drainage Improvement, Stage 2, Phase 2, Kai Tak Transfer Scheme (KTTS) project in 2000 to relieve potential flooding in Mong Kok caused by the insufficient capacity of the existing storm water drainage system. The KTTS involves construction of a 1.5km,4.4m drainage tunnel and a 450m long box culvert, running from Waterloo Road near Hereford Road to the existing Kai Tak Nullah in San Po Kong. This paper describes the design and construction of; the bored tunnel through both hard rock and soft ground using a slurry Tunnel Boring Machine (TBM), six associated access shafts, a connection structure at Waterloo Road and the box culvert connecting the bored tunnel to the outfall at Kai Tak nullah. Details will be provided on the contractor’s alternative designs adopted during the contract including the use of fibre reinforced shotcrete as one-pass temporary and permanent support for three of the shafts and modifications to the Engineer’s design for the box culvert structure.

Jan 1, 2005

The clay slime generatea in many sand washing operations is usually very difficult to de-water. Treatment of these slimes is often limited by economic considerations and the properties of the solids to a gravity-driven process. The moisture characteristics of kaolinitic slimes from two different sand washing operations were measured.From these curves, equilibrium moisture contents for sedimentation and for drainage were calculated using the methods of soil physics. The validity of these calculations were confirmed by column experiments.The results show that the increased de-watering to be gained by drainage, as compared with sedimentation, is significant. Furthermore, observed rates of outflow indicate that water can be removed considerably morerapidly when drainage is possible.The practical application of these results to the dewatering of clay slimes is discussed.

Jan 1, 1978

By R. C. Mahon

THE Homer iron-ore mine is at Iron River, Mich. Because it covers a large area, 400 acres, and because there was a considerable depth of water in the glacial drift above most of the ore bodies, this mine has presented a number of unusual and often difficult operational problems. The purpose of this paper is to discuss a few of the most important problems encountered. SURFACE WATER Mining on this property was started on one 40-acre tract. The ledge in this area was the highest on the property and, although it was a real problem, water could be handled by underground pumping. During the first period of mining, drifts were driven just under the ledge and holes were drilled through to the surface material. In later years these drifts have been extended wherever possible. Although these drifts assisted in the drainage problem, it was evident they would not be sufficient alone. Before mining on a large scale could be started on this property, the water problem had to be solved. A number of test holes were put down to the ledge, and showed that there was an average 150 ft. of water-saturated glacial drift above the ledge over the rest of the mine. The upper 70 ft. was gravel and sand and the lower 80 ft. clay and hard pan, with some narrow seams of sand and gravel. It was evident that the water above the clay seam could not be drained off through openings in the ledge and for that reason it was decided to install surface drainage wells. This method of drainage was entirely new at that time and was pioneered at the Homer mine. The sinking of the first well was started in June 1929. Immediately following the first well a number of wells were sunk, but only to the top of the clay seam. This was done with the idea that a greater capacity could be obtained in a shorter time from gravel seams where the water flowed more freely and that the cost of pumping the water above the clay seam would be considerably less than if the wells had all been sunk to the ledge at once. Before the drainage of surface water was started, 1200 gal. per min. against a head of 800 ft. was being pumped from the mine. By March of 1932, with five surface wells in operation, the mine pumping had been reduced to 150 gal. per min. At this time we were pumping 5000 gal. per min., under an average head of 110 ft. from the surface wells. The total pumping costs were 30 per cent less than in 1929 because the greater capacity was being pumped at a much lower head. From 1932 to 1936 the mine was idle and all surface pumping was stopped. Since 1936, 10 new wells have been added with a total pumping capacity of 8000 gal. per min. at the present time. The water level has been lowered 70 ft. since surface pumping was started in 1929, and it is now approximately at the top of the clay. To remove the water below the clay seam, 11 of the 15 wells were sunk to the ledge.

Jan 1, 1945

By Robert Livermore

IT has been a noteworthy feature of the Cobalt camp, that many of the valuable ore deposits have been covered, wholly or in part, by small but usually deep lakes, such as Cobalt, Cart, and Peterson lakes, and with the subject of this article, Kerr lake. In the early days of the camp many water-covered areas, which have since been found to be valuable, were ignored, or neglected by owners, or simply perfunctorily staked for water rights. Kerr lake is probably the evidence of a fault or sharp fold, having a general east and west strike, and containing a series of ore-bearing fissures, parallel generally to the strike, although having some notable exceptions to the general rule. On the north side of Kerr lake the formation is of diabase, while on the south side it is of Huronian slates and conglomerates. These Huronian measures extend out under the lake, dipping gently to the north to a lateral distance not yet definitely determined, owing to the lack of development under the deepest parts of the lake. Probably the contact between the diabase and Huronian or else between the former and the .underlying Keewatin formation occurs somewhere near the center of the lake. Kerr lake originally covered 45 acres. Of this the Kerr Lake Mining Co. owned 12, the Drummond Mine, 7, and the Crown Reserve Mining Co. the remainder of 26 acres. Since the latter's property was originally entirely under water, it was necessary for the owners to make land for buildings and shaft room. Accordingly, in 1908, a trench was blasted out which deepened the outlet, and lowered the lake 8 ft. As many of the rich veins of the Crown Reserve and Kerr Lake companies were under water, mining was pursued under some disadvantages. Fortunately the rock is tight and solid, and mining has been done sufficiently far from the surface to avoid unnecessary risk. Nevertheless, there was always danger of encountering open seams, through which too large a flow of water for comfortable working might come. Careful soundings were made over the veins, y means of steel-shod pipe, through mud and water to bedrock, but there was sometimes an element of uncertainty as to whether actual bedrock had been reached. Furthermore, the necessity of leaving safe backs between workings and lake tied up large quantities -of-ore, -and- made development- in certain

Jan 7, 1914

By Osvaldo A. Bascur

One of the most vigorous of the continuous improvement methodologies is Six Sigma. While usually associated with improving manufacturing and product quality, leading manufacturers are using it to improve their extended supply chain and logistics capabilities. At the same time they are improving reliability, some companies have cut hundreds of millions of dollars of fat out of their supply chain. Mine to Mill optimization is a transformation of culture from processing tons to processing a quality feed size distribution which reduces the overall operational costs and add the highest value to the mine. This is not a constant endeavor. As such, a dynamic performance monitoring and diagnosis is necessary. We will review a systemic way to performance improvements and avoiding metal losses from the blast to the metals. We show the requirements of using raw data to analysis the data to define operational maps which provide assistance to run the mine and mill. A case study is provided with the mine and mill data was integrated combining process control and quality information resulting in reduction of water and energy consumption while improving the overall value of the mine. The results of reengineering the current system with this SIX SIGMA Strategy had the following results: an increase of ore milling: 4.6% decrease of mil power: 3.9%, decrease of fresh water consumption: 6.8%, with a total of net profits: US$ 31.8 million, the PI System infrastructure contribution: US$ 7.95 million. These estimates were for the period 2009/04/04 to 2009/12/31.

Sep 1, 2012

Just three years after researchers announced its development, Dravo is putting the finishing touches on a new $60-million Thiosorhic lime mine/kiln complex near Maysville, Ky. Electric utilities in western Pennsylvania and Ohio have already signed long-term contracts for over three-quarters of the projected 907 000-t/v (1-million-stpy) production. Thiosorbic lime, a flue gas desulfurizing agent, proved in industrial testing that at high emission levels (greater than 3000ppm SO2) it could be twice as effective in SO2 capture as conventional lime, while eliminating the major problem of scaling and plugging of scrubber equipment.

Jan 4, 1977

By Homer S. Frankhouser

Materials may be dredged, processed, stored and loaded for shipment at a single site in water depths ranging from 250 to 1200 ft. Solution mining may also be accomplished in deep sea situations. And, open air subsea mines with direct surface access may be developed and worked under the ocean floor. These concepts for deep sea mining are the results of extensive testing of individual components of the proposed systems by Dravo Ocean Structures, Inc., a subsidiary of Dravo Corp. A basic structure in these systems is the articulated platform. The platform consists of a gravity- type base and a buoyant cylindrical column which is constructed at an onshore location, towed to the offshore site and installed in a matter of days without use of heavy equipment. The base is also buoyant for towing purposes. This allows for gradual flooding to the point of negative buoyancy for positioning and anchoring to the ocean floor.

Jan 1, 1971

By William Bogan, Mark Vaivoda, Richard Daniele

Many factors must be considered when performing engineering and construction work for a major minerals project. Dravo's Afton copper smelter in British Columbia illustrates some of the E&C factors considered when setting up this new operation. In March 1978, Afton Mines Ltd., a Tech Corp. subsidiary, began blister copper production at the world's first integrated copper ore mining, milling, and smelting operation to use Top Blow Rotary Converter (TBRC) process smelting technology. This key TBRC smelting element is licensed by INCO Ltd. to Dravo Corp. The TBRC process uses a single vessel of modular design. It rotates for mixing and provides complete processing capability, from concentrate through blister copper. The Afton facility is about 16 km west of Kamloops, a town in south-central British Columbia. To make its operation as economic as possible, Afton officials considered several options for the copper smelter, the first in modern times in the province. Inability to extract precious metals-primarily gold-from the concentrates ruled out hydro-metallurgical processes. The final choice was between a conventional electric furnace/ Peirce-Smith converter combination and the TBRC process. The TBRC process was chosen for its versatility in processing the various Afton concentrates and grades and its 40% lower capital cost compared to the electric furnace converter system. The TBRC smelter -including concentrate slurry receiving, drying, storage, smelting, off-gas cleaning, and copper casting-had an installed cost of about $25 million. In December 1974, a pilot program was conducted by Teck, Dravo, and INCO at INCO's Port Colborne, Ontario, research facility. The pilot program demonstrated the TBRC's ability to smelt, convert, and clean copper slags. After the successful pilot effort, Dravo performed additional research to find an effective fixation system for high grade, intermittent SO2 gases. Once the go-ahead was given, design and procurement for the Afton copper smelter was provided by the Denver Division, Dravo Engineers and Constructors. Commonwealth Construction, Vancouver, constructed all Afton facilities. Afton's single furnace smelter is designed to produce 25-kt/a blister copper in 363-408 kg cake form. The product is sold to England for electrolytic refining. The TBRC process is only one of several innovations proposed by Dravo and chosen by Afton to insure the most modern smelter in North America and meet all British Columbia's environmental restrictions. Conventional smelting methods use a separate furnace for each process step. The TBRC process employs but one furnace. The Afton TBRC vessel measures 6.4 m in length and 4.3 m in diameter. The furnace is supported on a set of motor-driven rollers. These permit the vessel to rotate at variable speeds to 40 rpm. Rotation provides good mixing, high reaction rates, and effective heat transfer from the refractory sides to the molten bath resulting in a low thermal gradient. The furnace can tilt through a full 360° for charging, firing, and pouring. Smelting at Afton is accomplished in sequential fashion. Flotation concentrate and limestone flux are initially charged to the hot, empty vessel. Using the water-cooled, oxy-fuel lance, the initial charge is smelted. Once sufficient molten bath is obtained and slagging completed, the metallic concentrate is charged. Materials are charged through the water-cooled, variable position additive chute mounted on the TBRC

Jan 10, 1980

By Didyk M. Marko, Vásquez Ñ. Gregorio

INTRODUCTION The Salvador Division of Codelco Chile is an important copper molybdenum production center, located 1,200 km north of Santiago and 124 km east of the Pacific Ocean, in the foothills of the Andes Range. El Salvador Mine produces by block caving 8,600,000 t of ore with a content of 1 .l0% Cu and 0.02% Mo, from a copper porphyry ore body. The geology of the ore body shows a great heterogeneity as to rocks, grade distribution, ore height and undercutting levels. This has resulted in a variety of designs for the productive units (blocks) and in the mineral handling systems. Up to now, 4 systems have been employed: grizzly and intermediate haulage; slusher drifts with intermediate ore pass and haulage; slusher drifts with scraper loading directly into trains; and, LHD. On the other hand there is a marked dispersion in the final results from each block mined out. We report here the conclusions reached after analyzing the data gathered on the mining of 163 depleted blocks, representing a total production of 102,000,000 t, with an undercut area of 340,000 sq m. The final results of each block, characterized in terms of tonnage and fine cop- per recovery, were studied as a function of a number of design, geological, and operational parameters. BASIC CONCEPTS Indices of Efficiency In order to evaluate the final result of each block, or group of blocks, the following indices of efficiency were defined : Tonnage Recovery (TR) . It is the ratio between the ore tonnage extracted and the in situ tonnage estimate for each block or group of blocks. Grade efficiency (E) . It is the ratio between the Cu mill feed grade and the in situ Cu grade estimate for each block or group of blocks. Grade efficiency is numerically equal to the ratio between fine copper recovery (FR) and tonnage recovery (TR) . Figure 1 shows the final results for 163 mined out blocks, in terms of tonnage and fine copper recovery. Different grade efficiencies are also indicated. The marked dispersion in the final results of mined out blocks must be stressed since it greatly incides in mine planning. It must be kept in mind that an eventual concentration of low overall efficiency in the blocks during a given period (e.g., one year) will make it necessary to bring into production new blocks over the standard development schedule. It is worth noting that the final results in the 163 mined out blocks corresponding to a production of 102,000,000 t of ore with a mill feed grade of 1.445% were obtained from an ore estimate of 93,000,000 t and a grade of 1.671% Cu, which represents 110% tonnage recovery and 86% grade efficiency. Parameters Studied The following parameters are considered in this study: Geological Parameters. These parameters depend exclusively on the geological and geotechnical features of the ore body. IN SITU GRADE: The initial estimate of the block grade. Four copper grade categories were considered : (a) lower than 1.3% ; (b) 1.3 to 1.6%; (c) 1.6 to 2.0%; (d) higher than 2.0%. The overall initial in situ estimate of the ore body was 1.6% Cu. IN SITU TONNAGE: Initial tonnage estimate of the block. Four categories are considered: (a) below 500,000 t; (b) 500,000 to 1,000,000 t (c) 1,000,000 to 1,500,000 t; (d) over 1,500,000 t. CONTACTS SLOPE: Since up to 4 rock types can be found in a block, resulting in a corresponding number of contacts, a horizontal con- tact was defined as that which forms an angle of less than 45" with the horizontal and a vertical contact that which forms an angle of more than 45" with the horizontal. GRADE DISTRIBUTION: As in rock types, horizontal and vertical grades were defined. ORE HEIGHT: The distance measured between the undercut level and the top of ore. Four categories are considered: (a) less than 60 m; (b) 60 to 100 m; (c) 100 to 150 m; (d)over 150 m

Jan 1, 1981

By Hannweg L. A.

In a first for the diamond industry, Koffiefontein Mine in the Free State, South Africa, opted for the front cave mining method to extract a 90 metre high block of kimberlite ore. Block caving, because of its high initial capital requirements, resulting in a negative internal rate of return (IRR),was ruled out as a feasible mining method for Koffiefontein Mine. Front caving is essentially a combination of the traditional block cave and sub-level cave mining methods, but uses two or more levels of retreating drawpoints. Two extraction levels, in the case of Koffiefontein Mine, are spaced 12 m apart vertically, with the upper 478 m level (48Level) acting as the undercut/extraction level, and the lower 490 m level (49 Level) as the extraction level. Caving is achieved by undercutting a small column of ore, which is then drawn, on both the 48 and 49 Levels, until the planned extraction percentage is achieved. The next column of ore is then mined by advancing the undercut (48 Level), and the process is repeated until the entire ore block is depleted to the contact. Caving-by-gravity techniques of mining rely on closely controlled draw of the caved ore to ensure proper caving action and to minimize the dilution of ore with waste material from the open pit. This paper discusses the need for, and implementation of, a draw control system at Koffiefontein Mine — a computerized production management system, and a draw control system based on linear programming, to allow control over the draw rate and mining sequence — a major factor in all production planning to optimize production efficiency, ore recovery and cave management. Keywords: Draw control, Koffiefontein Mine, Front cave, Caving

Sep 1, 2001

By K Nesbitt

Draw control at Premier Mine is considered important to avoid conditions of isolated draw, which results in early waste ingress, compaction of the kimberlite ore and loss of ore reserves. The Premier Mine kimberlite pipe is unique in that the pipe is cut at a depth of 400 metres below surface by a 75 metre thick gabbro sill. All cave mining at Premier is below the sill and failure to exercise good draw control could cause early ingress of gabbro waste. Gabbro causes problems in the diamond recovery plant and the amount of gabbro sent to the plant needs to be closely monitored. Fortunately coarse gabbro fragments are easy to recognise in drawpoints. It was anticipated that only 85 per cent of available ore would be drawn from the blocks immediately overlain by the gabbro sill before excessive gabbro waste forced the closure of drawpoints. Data on tons drawn per drawpoint and loaded per LHD as well as the tons tipped per pass is gathered by the vehicle monitoring and control (VMAC) system and information recorded by the load-haul-dump (LHD) drivers. Draw control staff monitor drawpoints on a shift basis and record the occurrence, type and height of hang-ups. Information pertaining to the status of the drawpoint in terms of support, waste and availability is also recorded. A database has been compiled that has been used to analyse the overall pattern of draw control, the frequency of occurrence of different types of hang-ups, secondary blasting efficiencies and drawpoint and LHD productivity. The gabbro sill has provided a unique marker horizon that has allowed the arrival of rock from a level 100 metres above the production level to be recognised. Data shows that ore migrates extensively towards groups of drawpoints that are heavily drawn with many drawpoints more than 100 per cent drawn before gabbro waste was recognised. This indicates that an accurate mixing algorithm is essential for good draw control. Data on tons drawn, drawpoint availability, productivity and the occurrence of various types of hang-ups has allowed better control of the mining operation and provided data for planning future caves. In the BA5 mining block a drawpoint spacing of 22 metres, horizontally across the major apex, has still allowed drawpoints to be pulled to waste with no loss of ore. In the BB1E mining block the drawpoint spacing has been increased to 23 metres and no problems have been experienced to-date. Future initiatives centre on improving the data gathering integrity of the vehicle monitoring and control system and a linear programme that will optimise draw control and productivity.

Jan 1, 2000

By R. L. Tobie, E. K. Staley

Because of high production demands at San Manuel mine (approximately 40,000 tpd) and the relatively narrow grade range of the orebody, no attempt is made by the company to mine selectively. The caving sequence is laid out to meet the production demands, and proceeds in a manner to induce the least amount of weight on extraction openings. Once an area is undercut, draw control procedures are applied uniformly until the area has been mined to depletion. The orebody, located 50 miles northeast of Tucsoil, Ariz., is a low-grade deposit of chalcopyrite disseminated throughout a structurally weak, highly fractured, strongly altered granitic host rock over- lain by several hundred feet of relatively competent andesitic conglomerate. When undercut, the granite ore caves readily into fragments which usually pass through the grizzly without either excessive breaking or an undue amount of secondary blasting.

Jan 6, 1967

By T. Glen Heslop, Dennis H. Laubscher

INTRODUCTION In all cave mining operations waste is drawn mixed in the ore, hauled, hoisted and milled. This waste usually contains some mineral which partly covers some of the costs of mining and milling it, but it still re- presents a loss of profits as the production rate from the mine is matched to the mill capacity - every tonne of waste milled replaces a tonne of profitable ore. Draw control aims to reduce the amount of waste drawn and to increase the amount of ore recovered. It is also used to regulate the grade of ore flowing to the mill and in block cave blocks to prevent potential stress build- up on the major apexes above grizzly drifts. This paper summarises what has been learnt about draw control in the forty years that cave mining methods have been used in the three largest underground chrysotile asbestos mines in the southern hemisphere. The four mining methods to which draw control has been applied are: a. Block caving. b. Shrinkage with overburden caving. c. Sublevel caving. d. Open stoping. Open stoping has been included because on a number of occasions severe falls from the back and side of these open stopes have occurred. Without full records of where and when ore is blasted, when and how much ore has been drawn from each of the drawpoints, it would be impossible to analyse the migration of ore and fallen waste in the stope. Several problems peculiar to chrysotile asbestos ore bodies affect the practice of draw control. Heterogeneous fragmentation, cavities, side pressures and the interaction of stresses in the caved ore affect the migration of ore under draw. Fibre is normally not developed uniformly throughout the ore bodies, values vary from place to place but there is usually a general decrease upwards and the hangingwall contact is an economic limit. The immediate hangingwall rock frequently looks like the ore body hostrock and is difficult to recognise in a drawpoint, and cannot be used as the marker for stopping draw. During caving or shrinkage, a large proportion of fibre becomes detached from the host rock and re- ports in the fines, which migrate differently to the larger rocks. The fines are not sticky, and flow easily if loose and dry, but compacted, the fibre and rock fines con- solidate the ore. During draw the proportion of fines in the ore varies considerably, as fines either flow relatively freely between the large rocks or become trapped and compacted above large rocks or hangups. This creates a large sampling error in drawpoint grade assessments, whether done visually or by bulk sampling, unless the assessments are done frequently. The method of draw control used is to regulate the draw rate in an attempt to lower the ore-waste interface as evenly as possible, and to finally stop working the drawpoint when a calculated tonnage has been drawn.

Jan 1, 1981

By Victor deWolfe

INTRODUCTION The Henderson Mine, located near Empire, Colorado, utilizes a continuous panel caving system to extract ore as one of the world's major producers of molybdenum. Any mine using a caving-by-gravity technique of mining must rely on closely controlled draw of the caved ore. This control is essential to insure proper caving action, to avoid damaging load concentrations of weight and to minimize the dilution of ore with waste material. Henderson is no exception. Draw control is a major factor in all production planning, from long- range plans to short-range and day-to-day ore scheduling. Draw control is reviewed constantly and administered daily in an effort to optimize production efficiency, ore recovery, and cave management. MINING METHOD The cave at Henderson is massive, moving slowly through large panels that are 244 m (800 ft.) wide by 610 m (2,000 ft.) long. Generally two cave areas are drawn at one time. The areas under active draw vary in size but can be as large as 244 m (800 ft.) by 244 m (800 ft. ) containing 400 draw points. Each draw point contains 45,360 mt (50,000 st) on the average and takes about two and one half years to exhaust. A complete panel is worked for seven to ten years. No pillar exists between panels, but rather a buffer zone of broken ore, or "static face," is left in each panel to be drawn with the adjacent, yet-to-be-caved panel in efforts of minimizing dilution of a working area from an exhausted one. (Figure 1) Production drifts are driven on 24.4 m (80 ft.) centers through the ore body. Between the production drifts are funnel-shaped draw bells on 12.2 m (40 ft.) x 24.4 m (80 ft.) centers to receive ore from the cave. Each bell is accessed by two draw points, one from the production drift on either side, thus forming a 12.2 m (40 ft.) x 12.2 m (40 ft.) draw pattern. Extraction of the ore is by rubber-tired, 3.8 m3 (5 yd3) load-haul-dump equipment. The LHDs then tram the ore a maximum of 49 m (160 ft.) to ore passes. Cave initiation and bell development are done from the undercut drifts which are parallel to and 17 m (55 ft.) directly above the production drifts. Longhole rings are drilled and blasted from the undercut drifts to define the bells and establish the undercut for caving. (Figure 2) DRAW CONTROL Since the cave line at Henderson is constantly advancing, it is necessary to be continually initiating new cave at one end while exhausting it at the opposite end. There must exist, therefore, an angle on the ore-waste contact in the broken rock from initiation to exhaustion. The basic concept of draw control is to keep this angle as smooth and even as possible, particularly at the time of exhaustion. If this is achieved, draw points are exhausted more or less in a line, avoiding pockets of remaining ore surrounded by exhausted areas. These pockets would cause spotty ore extraction at the time of exhaustion, increasing the amount of dilution occurring while introducing the potential for significant weight problems in the production area. To arrive at the desired angle on the ore- waste contact, maximum tonnage percentages are assigned to each row of draw points increasing at 10% or 15% increments (depending on cave size and velocity of draw) working away from the cave line. The available tonnage indicated by these percentages is the maximum allowable tonnage to be extracted from each draw point until the available tonnage percent- age is increased. As the cave moves, these percentages increase for each draw point regularly. However, in general the tonnage drawn from each draw point is kept at about 50% of this allowable maximum in order to maintain adequate available tonnage in the cave to sustain production for seven months if cave initiation were to cease. This available tonnage cushion is a safeguard built into the draw control program at Henderson to accommodate fluctuations in the rate of cave advance. When draw points move past the row of 100% tonnage availability, they are drawn past the desired 50% at the same increments per row until exhausted. (Figure 3) To achieve proper draw control, the number of LHD buckets to be taken from each draw point is assigned daily. The actual buckets taken, which may at times deviate from the

Jan 1, 1981

By A Gustafson, G Shekhar, P Boeg-Jensen

The amount of material extracted from each blasted ring in sublevel caving mines is vital when deciding the overall mine production target. The orientation of the production drifts is normally perpendicular to the strike of the orebody, and rings are blasted from the hanging wall side to the footwall side in a retreating manner. For an inclined orebody, a given ring will contain different amounts of material based on its relative position along the production drift. This layout creates a distinctive problem with respect to the extraction ratio optimisation along the axis of the production drift. This paper describes the current drawpoint control strategy practiced at LKAB and presents the variation of drawpoint performance parameters along the production drifts. It uses automatically generated data from a bucket weighing system that measures tonnage drawn per bucket, and it classifies the blasted rings into four zones based on their relative position along the production drift. It considers the loading procedure for blasted rings at Kiirunavaara mine and analyses the variations in drawpoint performance along the production drift. The paper finds that although the current draw control strategy is sensitive to ring position along the drift, it could be modified to optimise the final extraction ratio.CITATION:Shekhar, G, Gustafson, A, Boeg-Jensen, P and Schunnesson, H, 2016. Draw control optimisation along the production drift in sublevel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 241–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Secis R

Northparkes Mines is located 27 km northwest of Parkes in central west New South Wales. The E26 deposit is the largest of all defined to-date in the area, containing over 50 per cent of Northparkes' resources and reserves. The combination of orebody geometry and geotechnical characteristics provide ideal conditions for the block cave method of mining of the first lift of the E26 deposit. Although this method of underground mining has been used for decades in other countries, E26 is the first example of its use in Australia. Copper-gold mineralisation at Northparkes is related to quartz monzonite porphyries that have intruded coeval Ordovician volcanics. Sulphide mineralisation (dominantly bornite and chalcopyrite) occurs principally within quartz veins associated with the porphyry intrusions. Veining and mineralisation occurs within both the porphyries and volcanics. To optimise the recovery of a resource within a block cave mine, a good understanding of the rock mass and ore flow characteristics is essential. These have a significant effect on the fragmentation size and range and on parameters such as the drawzone spacing, height of interaction zone and dilution entry. As ore within a cave column moves and mixes when material is extracted from below and beside it, the total reserve extracted is unique for a particular draw strategy/production history. Until recently, reserve estimates and production schedules were based on the application of a uniform dilution factor to the tabulated resource. However, given the complicated flow and mixing within the cave column, such a simplistic approach can produce erroneous results. Northparkes Mines purchased and sponsored the upgrading of a commercially available software package specifically developed for modelling removal of resource blocks under caving conditions. This Gemcom software package, PC-BC, has been used for mine planning, reserve reporting and production scheduling. Blocks within it resource block model are converted into a mineable reserve taking into account mixing and dilution during depletion of drawcolumns (by horizontal and vertical redistribution of insitu tonnage and metal). As PC-BC gives individual drawpoint reserves, it can be used during the planning stage to determine whether or not a drawpoint is economic. For E26 Lift I an optimal layout containing 130 drawpoints has been developed based on a nominal 14 m x 14 m drawpoint spacing and a 0.8 per cent equivalent copper (eCu) cut-off grade. Annual production schedules for the depletion of material above this layout are based on: I higher tonnage removal from higher grade drawpoints in the early years of production; and 2 drawpoint production rates proportional to the total tonnage of orr remaining in the drawcolumn up to the optimal height of draw tier subsequent years. The reserve is tabulated from the combined annual production schedules over the life of the lift. The pre-mining reserve for Lift I of E26 is 26.6 Mt at 1.43 per cent copper and 0.39 g/t gold, of which approximately 23.4 Mt will be extracted under caving conditions. By scaling down the annual production schedule, weekly drawpoint tonnage calls can be given for short-tern production scheduling.

Jan 1, 1997

By R. Mulyanto, M. Siray, A. Parhusip, F. Hartono

"PT Freeport Indonesia is preparing the Deep Mill Level Zone (DMLZ) mine to be the successor of the currently operating Deep Ore Zone (DOZ) mine. The DMLZ is block cave mine situated 500 m below the DOZ mine and approximately 1600 m depth from surface. Both of the block caving mines require draw point construction in the extraction level to extract the ore from caved area above. Learning from the experience in DOZ, the construction & maintenance of draw points in the production panels is a significant challenge in supporting consistent production.The average DOZ draw point construction duration is approximately 46 shifts per draw point. The time frame for construction is dependent on several variables; availability of the conventional forming system, material availability, and development tolerances. The repair of concrete floors and lintel sets causes production downtime. Reviewing the old DOZ draw point design, there is an opportunity to increase constructability, durability, and reliability of DMLZ draw points. This paper discusses how the DMLZ has improved draw point construction productivity and is on track to significantly reduce costs whilst increasing the quality by using the Six Sigma Improvement Method.Introduction The DMLZ Mine is part of the PT. Freeport Indonesia (PTFI) future Expansion to its underground mining complexes. It is the fourth vertical lift in the East Ertsberg Skarn System (EESS) deposit (Figure 1).Currently, it is under development phase.The DMLZ mine will be a block cave mine using an advanced undercutting method. The DMLZ extraction level will be approximately 1,600 meters below the surface on the 2570 level with column heights of roughly 500 m. The Undercut is on 2590 level, some 20 meters above the extraction level."

Jan 1, 2016

By D. E. Ranta, M. G. Schulz

Mining of Molybdenum at Questa, New Mexico has been accomplished by block cave methods since August, 1983. As caving progresses, a periodic geologic evaluation is made of the rock types present in finger raises on the Grizzly Level of the mine. The production maturity of the cave can be monitored by relating this data to geologic cross-sections through the orebody. The draw point mapping program is a simple and effective tool that is used in making draw control decisions at Questa.

Jan 1, 1992