Search Documents

Owing to the 'creeps' and consequent movements in the mines, followed by the recent fire in the southern workings, the whole of the orebody above the 800 ft. level is now very much crushed and broken. The same applies to the hanging wall or overwall coutrny, which has subsided towards the workings, so that for some years past all development work within the lode has had to be carried out with extreme care.The continual but slow subsidence of the overburden into the stopes necessitates a periodical renewal of all gangways in the lode, and, as the subsidence amounts to as much as 60 ft. in places, these new gangways must necessarily pass through the mullock-filling of old stopes in addition to broken ore. They at times pass into the broken ground of the hanging-wall for some distance, where the orebody has widened underneath by the original folding and puckering.

Jan 1, 1932

By V. Y. Kirillin, V. A. Rumjantsev, S. A. Tchesnokov, Yu A. Veksler, V. F. Kalmykov, A. N. Telgarin, A. T. Shakirov

Mining in outburst hazard seams may be safe and effective if some preventive measures, such as lowering gas and rock pressure as well as speed regulating of a continuous miner in cutting the seam would be practised. The driving speed should be optimal as the low speed lowers labour productivity but the high speed may cause gaso-dynamic phenomena. At this mine the driving speed is regulated by seismo-acoustic control of the seam condition.

Jan 1, 1985

By Ery Wardhana, Stefanus Jagad, Relinda Sanistya, Hasucita Tausi, Rido Situmorang

The blasting process is one of the most high-risk activities in mining operations. Shotfirers and blasting crews face hazards from slope failure, toxic gas and fumes, or unstable ground condition every day of the blast. But on the other hand, to ensure all of the holes are detonated, shotfirers are required to reenter the location to check. With advances in technology, nowadays the use of drone in mining is not something that is rarely seen. It has been used for mapping and slope-monitoring. This paper will discuss the application of drone for blasting process in a mining pit in East Kalimantan, Indonesia. By using drones, it is not only safety factor which can be improved but also operational efficiency and technical analysis. The duration it takes for post blasting process can be reduced because the drone can directly enter the location after blast. The technical analysis for the blast can also become more comprehensive, as the before-after photos and video documentation can be taken with wider view. It helps with fly rock calculation and fragmentation analysis too.

Feb 6, 2023

By Jose A. Gomez, Javad Sattarvand

Failures of tailings dams have been happening lately. Due to the lack of laws on particular design criteria and stability requirements related monitoring during construction and maintenance, they are thought to be more fragile than hydraulic dams. Monitoring the dam is therefore necessary to understand its current condition and guarantee its safety. The physical condition of the dam could be evaluated with the early identification of seepage. Additionally, due to their adaptability and capacity for high-resolution data collecting, UAVs are an excellent choice for efficiently covering the tailings dam site. UAVs may capture high-quality photos when equipped with a high-resolution RGB camera, thermal sensors, or multispectral sensors. When these sensors are paired with image processing and machine learning algorithms, the result is a reliable estimate of the dam condition.

Jun 25, 2023

By J. A. G. Llerena, J. Sattarvand

Tailings dam failures have been occurring in recent years. They are considered more vulnerable than hydraulic dams due to the lack of regulations on specific design criteria, and stability requirements regarding monitoring during the construction and maintenance process. Thus, monitoring the dam is essential to know the dam's existing state and ensure its safety. One of the reasons tailings storage facilities fail is slope instability caused by moisture content. A relationship does exist between moisture content and surface strength, early detection of seepage would help to assess the physical condition of the dam. Moreover, to cover the tailings dam area in an efficient way Unmanned Aerial Vehicles (UAVs) are suitable because of their versatility and high-resolution data acquisition. Mounted with a high-resolution RGB camera, and thermal, or hyperspectral sensors UAVs can acquire good quality images that combined with image analysis and machine learning algorithms yield a good estimate of soil moisture.

Feb 1, 2023

By Jesus Layten, Marcos Garayar

Los RPAS (Remotely Piloted Aircraft Systems, por sus siglas en inglés) o drones son aeronaves (plataformas) que vuelan sin tripulación de manera automatizada, a las que se les puede adaptar diversos tipos de sensores. Esta tecnología nos brinda la posibilidad de obtener imágenes de alta calidad y precisión, de manera eficiente, confiable, segura y de menor costo. Asimismo, permite realizar trabajos en zonas de difícil acceso, ya sea por razones geográficas o sociales. El desarrollo de los trabajos con drones involucra una serie de procedimientos y técnicas que se abordarán en el presente trabajo, junto con ejemplos de levantamientos exitosos realizados en proyectos mineros y de infraestructura en Perú.

Sep 20, 2019

By Rafael C. Castro, Geoffrey Hughes, Fredrick (Rick) Vincent, Philip H. Albert

Seven pairs of drop and ventilation shafts, between two and nine feet in diameter, will convey combined sewer flow to a 230-foot-deep, 26-foot diameter storage tunnel. This paper will present case histories for each site. Discussion will include functional requirements, program and site access constraints, structural design, geology, the variety of excavation and lining construction methods used, and lessons learned. Noteworthy observations include the importance of assuring competent ground sup-port at the soil-bedrock interface and of achieving tight verticality tolerance using both top-down and raise bore excavation methods.

Jan 1, 2007

By P. W. Allen

Here are the facts and the figures on how Tahawus cut costs and improved safety in solving their secondary breakage problem - A dropball crane entirely eliminated secondary blasting.

Jan 4, 1953

By Subagyo, Geoffrey Brooks, Ken Coley

The generation of droplets and their subsequent reaction in the emulsion is critical to the overall kinetics of oxygen steelmaking. High temperature experiments have been performed at McMaster University to study this behavior. The results from this work and other previous studies has formed the basis of a number of physical and chemical models that attempt to describe the critical aspects of droplet behavior in Oxygen Steelmaking. These models include semi-empirical models for predicting droplet generation rate, droplet size distribution and droplet residence time as a function of blowing parameters.

Jan 1, 2004

By F. Rivard, M. G. Drouet, W. S. Ruff, P. Carabin

"In both the hot rotary-salt-furnace (RSF) treatment of aluminum dross and the cold ball-millsieving (BMS) treatment of zinc dross, enormous amounts of energy and recoverable metal are wasted and large amounts of greenhouse gas are produced. Such wastes and the environment pollution could be avoided by using the DROSRITE PLUS™ technology. Economic and GHG production comparisons between the presently used industrial treatment processes and DROSRITE PLUS™, supported by over one hundred tests conducted in Canada, the US and Europe, are presented. The savings, with DROSRITE PLUS™, would be about $191 and $418 per MT of aluminum and zinc dross, respectively.INTRODUCTIONDross is a material, which forms on the surface of molten non-ferrous metal, such as aluminum or zinc, during melting, metal holding and handling operations when the molten metal is in contact with a reactive atmosphere. Dross normally consists of metal oxides entraining a considerable quantity of molten free (unreacted) metal, and for economic reasons it is desirable to extract the free metal before discarding the residue. In the case of aluminum dross, recovery of the metal is usually carried out by treating the dross in a furnace at a high temperature (Peterson et al., 2002). By contrast, cold zinc dross is crushed in a ball mill followed by sieving to separate the coarse metal portion from the fine oxide residue.The conventional aluminum dross treatment process, using gas or oil-heated rotary salt furnaces (RSF), is thermally inefficient and environmentally unacceptable because of the salt slag and CO2 produced from the combustion of fossil fuels. In the past several years, a number of salt-free processes have been developed and some of these have found limited commercial use (Gripenberg et al., 1994; Lavoie et al., 1990). In all these dross treatment processes, heating of the cold dross in a rotary furnace requires an external energy input that varies between 375 and 2,500 kWh per (metric) tonne of dross. Molten metal separated during processing of the heated dross is tapped, and the remaining solid residue is discharged from the furnace."

Jan 1, 2012

By Rodney L. LeRoy, Michel G. Drouet, Peter G. Tsantrizos

"DROSRITE is a unique process that makes possible economic in-plant recovery of metal from hot aluminum dross. It is environmentally friendly, requiring no salt and producing no C02 or NOx gases. The salt-free residues of the process are suitable for production of calcium aluminate or for other value-added use. The process is highly energy efficient, extracting process heat from energy in the residue and, thus, it does not require an external plasma torch, electric arc or fuel heat source.A DROSRITE pilot unit built by PyroGenesis has been tested with both black and white dross types. The unit was installed at two different aluminum plant locations, and tests were conducted for a total of six weeks ""online"" with hot metal holding furnaces where the dross was skimmed.Results of both of these industrial trials are presented, together with an economic analysis indicating cost savings in excess of $1 70 per ton of dross treated."

Jan 1, 2000

By Ray D. Peterson, Annette Revet

The optimization of secondary aluminum furnaces is critical to the efficient operation of a recycling facility. Since all metal loss occurs in the drosses, physical and chemical analyses of these by-products are valuable diagnostic tools. Dross analyses can provide information concerning total furnace metal recovery efficiency as well as identifying areas for potential improvements. A complete dross analysis is a labor-intensive process that requires significant care both in sampling and performing the analytical techniques. Experiments can be done at a bench- or plant-scale depending on the facilities available. This paper outlines the benefits and information that can be generated through dross studies. Furthermore, several analytical methods are discussed as well as the special requirements needed to gain accurate results. Experimental data from industrial studies is provided to demonstrate the use of dross evaluations for ~ace optimization.

Jan 1, 2000

By Daniel E. Groteke

This paper describes a new technology which allows aluminum drosses to be processed at the generating melting furnace to recover available metallic values. The systems, offered in both manual and automatic modes, are capable of processing quantities ranging from 15 to 200 lb. per cycle, and recovering up to 90% of the aluminum with a combination of agitation and chemical reactions. In the automatic mode, the separation of molten alloy and de-metallized dross is achieved in less than five minutes process time. The recovered alloy, of largely unchanged composition, may then be returned while at elevated temperature to the original melting furnace to achieve an additional saving of energy.

Jan 1, 2000

By Jim Wilcox

Introduction In 1979, rumors of a developing drug problem within IMC Fertilizer's Carlsbad, NM workforce began to surface. For the next two years, a management team contacted local, state, and federal regulatory agencies that had the potential resources to help combat this apparently escalating problem. These contacts included the local police department, the county sheriff's office, the federal Drug Enforcement Administration, and the Mine Safety and Health Administration (MSHA). IMC approached each agency with two proposals. The first required the agency provide an undercover agent for placement in the company's underground facilities. The alternative required the company to provide the agent with the participating agency lending necessary legal expertise and guidance to accumulate the necessary data. MSHA regulations prohibit intoxicating beverages and narcotics on mining property. They also forbid persons under the influence of alcohol or narcotics from working in or around mines. The agency could not, however, help with this problem. The remaining agencies were sympathetic, but were unwilling to assist in implementing either program, citing legal implications. Without exception, these agencies not only refused to provide help, they discouraged any type of undercover operation, searches, drug screenings, or using dogs trained in narcotics detection. As law enforcement officials, they reasoned that any such program constitutes potential civil rights violations. An attorney advised IMC that it was not required to adhere to the same guidelines as law enforcement and regulatory agencies. It was his legal opinion that the company could conduct an undercover operation. But he recommended finding a private firm that specialized in this type of investigation. An experienced firm should have the expertise to conduct the operation and avoid the legal pitfalls that could be encountered. The management team agreed with the attorney and elected to hire a private firm. After extensive research and evaluation, three reputable companies were contacted, advised of the needs, and asked to submit a proposal. Their initial response was enthusiastic. None, however, submitted a proposal. Each was unable to locate a qualified agent willing to work in an underground environment. Privacy and civil rights At this point, it was apparent that an undercover operation was not feasible due to the lack of inhouse expertise and the lack of outside assistance. After more research, it was concluded that the only viable options left were the ones that the law enforcement community had earlier discouraged. These options included locker and personal searches, use of dogs trained in narcotics detection, and drug screening or testing. The management team evaluated the pros and cons of locker and personal searches. They concluded that if conducted properly, this approach could eliminate the problems. The potential legal liabilities, however, appeared to be tremendous. Strict guidelines would have to be adhered to in order to avoid invasion of privacy and civil rights violations. This meant announcing locker searches before conducting them and obtaining written permission from an individual before searching his person. Although the group was reluctant to lose yet another option, it was concluded that conducting searches under these conditions would be ineffective. It would also convey the message to the workforce that the substance abusers had the upper hand. This author was extremely critical of this legal opinion at the time. I have since concluded that the attorney was correct. This occurred in mid-1982. Court decisions of that era indicated the legal and political climate was sensitive to these issues. These activities would probably have been prohibited even if they were

Jan 11, 1987

By J. M. Manka

American mining companies operate many drum hoists, hoisting from varying depths with varying payloads. This paper reviews the procedure for selecting optimum wire rope constructions for existing hoisting installations. Selection for proposed installations, along with recommended hoisting parameters, is also discussed. To achieve optimum rope performance, preventive and corrective maintenance procedures are required and are reviewed here, along with examples of rope problems and their causes.

Jan 1, 1993

By J. M. Manka

American mining companies operate many drum hoists that hoist from various depths with varying payloads. This paper will review the procedure of selecting optimum wire rope constructions for these existing hoisting installations. Selection for proposed installations along with recommended hoisting parameters will also be presented. To achieve this optimum rope performance, preventative and corrective maintenance procedures will be reviewed along with examples of rope problems and their causes.

Jan 1, 1992

By Mike Robotham

When RFQ?s are received they often contain detailed technical specifications which suggest a departure from the suppliers own customary approach to the design. Both client and end user are quite rightly influenced by their own experiences. The question is who is right, the client and his consultant, the supplier or perhaps a combination of these. This paper looks at some of the fundamental variances that often occur in the approach to the mechanical design of drum hoists, based on our experiences of recent years. Director of Engineering, Mike Robotham is a chartered engineer and has been with DavyMarkham for over 30 years. Having completed a craft apprenticeship he later joined the engineering department as a junior engineer. He has a wealth of experience of working on medium to large engineering projects in the field of mechanical, electrical and hydraulic equipment

May 1, 2011

By Gordon F. Scott

This paper considers a recently completed hoist project for IAMGOLD. Called the Westwood project, this mine utilises some of the largest drum hoists supplied to the North American Market in recent times. This project is an example of where many of the design features discussed the associated paper, (Robotham, 2011) were incorporated. Director of sales and marketing, Gordon Scott has worked at DavyMarkham for over 30 years in a variety of roles starting as a mechanical design engineer, moving to project management before joining the sales department. Gordon has an honours degree in mechanical engineering from Leeds University.

May 1, 2011

A model has been developed for drum scrubbing which allows selection of geometry and power input. Specific aspects considered are: Calculation of total static and operating volumes. Total residence time based on total operating volume. Solids residence time based on solids operating volume. Selection of the aspect ratio. Alteration of operating fill to allow for smaller or larger feed openings. Selection of proportion of critical speed. Calculation of shell and motor power requirements. The model uses either solids or total residence time to calculate the required operating volume. The solids residence time is based on the proportion of coarse solids in the feed. Material finer than the reject size is considered as part of the slurry. The solids operating volume is the static volume plus the surcharge on the discharge weir required for flow of the solids from the unit. The total operating volume is the static volume plus the surcharge on the discharge weir for the total flow to exit the scrubber. The burden density is calculated from the coarse solids bulk density and the slurry density that includes all the fine solids. Power is calculated using the Liddell and Moys correlations for burden position and shape, and the operating rotational speed. Results from the model (especially power) have been verified from industrial installations of significant size. Predicted and observed power draws are within two per cent. A check against the JKMRC mill model shows power draw prediction agreement to within four per cent.

Jan 1, 2004

An improved method of sample recovery for use with rotary percussion drilling has been developed. Cuttings can be recovered continuously from either dry or wet drilling, and the recovery under dry conditions is seldom below 99% of the cuttings brought to the surface by the rig. The system is designed for use with top drive drilling rigs using flush-jointed drill rods. The key feature of the system is a self-aligning mechanical seal around the drill rods. The sealing unit is removably fixed to a collar section of cas ing. the cuttings are recovered in a plastic bag attached to the bottom outlet of a cyclone. A valve at the bottom of the cyclone permits the cuttings representing various depths to I,e recovered separately for examination eind 0(iclysis. [u the Iron Monarch quarry, two percussion holes were drilled to depths if 30 metres and 28 metres using the unproved sample recovery system, and diamond drill holes bored 1 metre from each percussion hole. Samples from each hole were sectionalized over metre intervals and analysed for iron, silica, alumina and loss on

Jan 1, 1976