Search Documents

By J. Petersen, H. Naderi, H. Zare, M. H. Nikzad, M. Karimi

In the copper electrorefining process, the dissolution of anodes is significantly reduced or even stopped when the passivation phenomenon occurs. The results of this phenomenon are increasing energy consumption, residual formatting, and voltage levels in the cell. In this study, the electrochemical behaviour of blister copper in the presence of sodium persulfate (PDS) was studied. The electrochemical methods of LPR, Tafel, and Electrochemical Impedance Spectroscopy (EIS) were used. The results showed that the addition of sodium persulfate activates the electrode surface and increases the open circuit potential. In the presence of PDS, the polarisation resistance of the electrode shows an increasing or decreasing tendency, based on the PDS concentration. This tendency is probably due to the formation of surface layers (such as slime layer or copper sulfate) and dissolution of this layer at various concentrations of PDS. The lowest polarisation resistance of 1.8 ohms and the highest corrosion current of 60.6×10-3 and 36.6×10-3 A/cm2 from LPR and Tafel techniques respectively were obtained at the concentration of 40 g/l PDS. Based on the results of potentiodynamic and electrochemical impedance spectroscopy tests, the addition of sodium persulfate to the solution reduces the corrosion resistance, therefore the passivation time of the blister copper anode increases. Keywords: Blister copper, electrorefining, sodium persulfate, anodic passivation

Jan 1, 2020

By Zehong Wang

Selecting sodium polyacrylate (PAAS) as grinding aid, the effect of grinding aid on the grinding efficiency of bauxite taken from Shanxi province was studied and its mechanisms were analyzed by measuring the variation of adsorption characteristic, pulp viscosity, surface electric potential of the bauxite and the surface appearance of particles. The results showed that, compared with no grinding aids added the content of -0.074mm in the ground product was increased by 5.45 percentage points under the optimal grinding conditions adding PAAS as grinding aid when the amount of PAAS was 0.7%wt of bauxite. Because the physical adsorption and chemical adsorption were occurred on the bauxite surface, which could reduce the pulp viscosity, change the surface electric potential of the bauxite, enhance the surface appearance of particles and lower the surface hardness of the bauxite, the grinding efficiency of bauxite was increased by PAAS. Keywords: bauxite, grinding aids, grinding efficiency, mechanism

Sep 1, 2012

By G P. W Suyantara, Y Tanaka, T Hirajima, Y Aoki, K Sasaki, H Miki

The effect of sodium sulfite (Na2SO3) on the flotation behaviour of bornite and tennantite is reported in this work. Flotation tests were performed using pure minerals of bornite and tennantite under various concentrations of sodium sulfite at pH 9. The flotation results indicated that sodium sulfite exhibited a depressing effect on the floatability of bornite in the presence of 0.1 mM PAX. However, tennantite remained floatable after the addition of sodium sulfite in the presence of 0.1 mM PAX. The flotation tests using mixed bornite and tennantite confirmed the flotation results of single minerals. Surface characterisation using X-ray photoelectron spectroscopy (XPS) was performed to explain the flotation results. A mechanism is proposed based on the XPS analysis results.

Aug 24, 2022

By A Van den Bulck, K Verbeken, O Vergote, I Bellemans

Viscosity is one of the most important physicochemical properties during pyrometallurgical operations. In the sub-liquidus regime, an important factor is the presence of suspended solid particles, yet its influence is not well-described in earlier literature, despite the significance of this factor. This project aims to determine the influence of spinel particles (Zn(Al,Fe)2O4) on the rheology of a multiphase synthetic PbO-SiO2-ZnO-Fe2O3-CaO-Al2O3 slag system. Three data sets with a wellcontrolled methodology and three different spinel sizes (small (13 μm), medium (34 μm) and large particles (76 μm)) were published previously, using a custom-built high-temperature rheometer. This study presents an additional data set of slag viscosity measurements, performed using a different apparatus, the Anton Paar FRS 1800, to verify the consistency of the earlier determined viscosity behaviour. Within this data set, no consistent trend could be found between the predicted wt per cent spinel and the relative viscosity. Therefore, additional quenching experiments were conducted to identify the morphology and experimentally determined volume fraction of the spinel particles in the slag. These measurements revealed a difference in spinel size across the samples and corresponding viscosity behaviour, emphasizing the importance of spinel particle size on slag viscosity. Once the spinel size was taken into account, consistent viscosity results (relative apparent viscosity and flow index) were observed across the two devices. This study confirms that, once all parameters affecting slag viscosity are considered, the viscosity behaviour of a heterogeneous slag can be uniquely determined. The resulting optimised slag viscosity models can be used to predict viscosity before processing, addressing relevant phenomena such as slag tapping, slag foaming and copper droplet settlement.

Aug 21, 2024

By R. G. Reddy

The effect of solid particles on viscosity behavior of Na2O-O-B2O3-SiO2 melts of composition XSio2/XNa2o =0.5 and in the temperature range of 900- 1150 K was studied. Samples were analyzed by X-ray diffraction and optical microscopy. The results showed that a crystalline phase (NaBO2) was formed and its amount increases with decrease in X,, from 0.50 to 0.25. The experimental viscosity values were compared with the predicted values using our viscosity model developed earlier. At low temperatures, for low content of B2O3 , the experimental values exhibits a large deviation from the predicted values. It was concluded that the deviation was due to the formation of solid particles in the molten slags. The existence of these solid particles increased the viscosity values significantly. A new viscosity model was developed to include the effect of solid particles.

Jan 1, 1993

By N Kado, T Iwama, R Inoue, S Ueda

Steelmaking slags are usually used as roadbed and civil engineering materials. However, the expansion phenomenon, which is caused by the volume expansion during hydration of free CaO and free MgO contained in steelmaking slag, is indispensable. Since the hydration of free MgO in steelmaking slag is much slower than that of free CaO, it is qualitatively considered that free MgO contributes to the hydration expansion of steelmaking slag over a long period of time. Similar to free CaO, free MgO consists of undissolved MgO and crystallised MgO in steelmaking slag. The latter precipitates during slag cooling. When divalent metal oxides (FeO, MnO, CaO) are dissolved in the crystallised MgO to form a MgO-based solid solution, it is expected to inhibit the hydration reaction similar to precipitated CaO. From the previous hydration test of Magnesioferrite, which was calcined after mixing MgO and Fe2O3 reagents, it was found that the higher the Fe2O3 concentration, the slower the hydration reaction progressed. In this study, by clarifying the influence of calcination conditions of MgO-FeO and MgO-FeO-MnO solid solutions, which were prepared by the calcination of mixture of MgO, FeO and MnO reagents, on their hydration reactivity, the effect of composition and thermal treatment on the formation of free MgO that is not hydrated (or easily hydrated) were discussed. To investigate the influence of MgO grain size, coarse MgO particles, which were obtained by crushing MgO crucible, were also used for heat treatment. With increasing the amount of FeO and MnO in the MgO-FeO-MnO solid solution, the hydration reaction became more suppressed. The expansion suppression effect was higher with solid-solved FeO than with solidsolved MnO. When the calcination temperature of the MgO-FeO solid solution was increased, the Fe3+/Fe2+ concentration ratio increased, resulting in a higher hydration rate.

Jun 19, 2024

By Bryan C. Smith, Duane R. Skidmore

Volumetric mass transfer coefficients and gas holdups were measured in a concentric tube airlift reactor designed for the microbial desulfurization of coal. The slurries were comprised of an acidified basal salts solution containing thirteen different weight percents of coal (74 µm Ohio #1) at three temperatures. An enhancement in the mass transfer coefficient, KLa, with respect to that measured in pure solution was found at weight percents of 5 (volume fraction solids, ES = 0.035) or less, the greatest enhancement being as great as 37% at approximately 2 weight percent (ES = J 0.014). At higher solids fractions, the mass transfer coefficient decreased with further solids additions, decreasing by as much as 91% at 40 weight percent coal (ES = 0.315). KLa increased with temperature at all solids concentrations, the greatest increase being 392% at 72°C vs that measured at 30°C. Gas holdup, EG decreased with all increases in solids loading by as much as 65% and increased by as much as 67% with temperature. KLa and EG were correlated with operating conditions separately, and the separate correlations combined to yield overall correlations for the mass transfer coefficient and for the gas holdup. The correlations are suitable for inclusion in system models devised earlier for microbial coal desulfurization processes, and may be used for design, operation and cost estimation for such systems.

Jan 1, 1989

By Larry M. Southwick

Extraction of gold and other metals from ores suspended in liquid slurries often involves gases (such as oxygen) as a participant in the reaction. An important factor then in setting the rate of extraction can be mass transfer of the gas into the liquid and/or solids. A number of recent studies have indicated that as solids loadings increase, mass transfer rates of gas into solid-liquid mixtures decreases. This would seem to imply that lower solids loadings would be beneficial to increased reaction rates. However, since it is the solids which are being reacted, a most intriguing paradox is created. More solids should lead to more surface area to react, but it seemingly also provides less gas to react. So is the reaction faster or slower as solids loadings increases? The creation of this paradox is imbedded in how mass transfer and reaction data is collected and measured, how it is analyzed and correlated, and finally on the rate controlling steps in the reaction. An alternative analysis of these studies is presented which clarifies and eliminates the paradox. The analysis applies to water slurries as used in gold or other metal leaching processes or in bio-hydrometallurgy, as well as to molten metal/solid/gas mixtures such as might be encountered in submerged gas injection.

Jan 1, 1999

By N. N. Clark, C. M. Atkinson

Pachuca tanks are used widely in the mineral industry for leaching and mixing operations. An analysis has been presented previously to predict circulation of homogenous slurry in Pachuca tanks with full height draft tubes. However, settling of solids causes deviation from the homogenous case. Circulation of settling slurry in a Pachuca tank is modeled and shown to be a function of settling velocity, solids fraction, solid and liquid density, air flew rate, and tank dimensions. The pressure balance is shown to be very sensitive to these parameters, especially at low slurry velocities. Equations for predicting the air requirements in Pachuca tanks containing settling solids are presented.

Jan 1, 1988

By Hongbo Zhao, Jun Wang, Wenqing Qin, Guanzhou Qiu

Jan 1, 2015

By John L. Lamont, Walter Crafts

AN investigation has been made of the multiplying factors for some of the more common alloying and deoxidizing elements for use in calculating hardenability of steel according to Grossmann's method.1 The factors for manganese, silicon, and aluminum that were reported in an earlier communication2 have been confirmed by microscopic determination of the half-martensite structure rather than on the basis of an empirically determined hardness corresponding to a half-martensite structure. Measurement of ideal critical diameter by microscopic examination was found to he necessary for other alloying elements, and multiplying factors for nickel, chromium, molybdenum, zirconium, vanadium, titanium, and boron have been determined. The nature and order of magnitude of the multiplying factors reflect the effect of the alloying elements on the structural character of the steel. Except for nickel and vanadium, the multiplying factors agree fairly well with previously published results. Good correlation between actual and calculated ideal critical diameters has been found in developing the multiplying factors and in checking the results against fairly simple steels. However, some discrepancies have suggested the need for a more thorough study of low-carbon and complex steels. TESTING PROCEDURE The investigation was conducted principally on steels made at the Union Carbide and Carbon Research Laboratories, Inc., in high-frequency induction furnaces using Armco iron and standard alloying materials. However, a few open-hearth steels were used in establishing the effect of nickel, and the hardenability factor for boron was based primarily on open-hearth steels. All bars were normalized prior to the machining of Jominy hardenability specimens. The Jominy test was carried out under conditions standard for the test.3 Austenitizing temperatures judged to-be-appropriate for the composi¬tions of the steels were used., Chemical analysis was determined on a sample taken adjacent to the Jominy specimen. Residual amounts of phosphorus, sulphur, nickel, chromium, molybdenum, and copper were determined on only one heat of each group made with the same materials during the same period. "Acid-soluble" aluminum and zirconium rather than total amounts were determined, as it is considered probable that the acid-soluble amount is more representative of the effective alloy. As tin was present to the extent of only 0.002 per cent, its effect was neglected. The method used to determine boron in the steels shown in Table 9* was developed by Galen Porter, Vincent Napoleon, and Thomas R. Cunningham,of the Union Carbide and Carbon Research Laboratories, Inc., and is. a modification of J. Naftel's procedure for boron in soils

Jan 1, 1944

By B. Kahraman

About 70% of the world?s total boron reserves are located in Turkey. Boron minerals are typically concentrated by attrition scrubbing followed by screening and classification to remove clay minerals and other impurities. These wet concentration methods, however, result in a considerable amount of accumulated tailings in large tailings dams. The tailings are approximately 28% solids and contain 14% B2O3. Problems caused by these tailings can be minimized by employing dry beneficiation techniques involving heat treatment. This method has been successfully tested on laboratory and pilot scales. During heat treatment, borax undergoes expansion in volume. The amount of expansion is dependent on the particle size, temperature and duration of heat treatment. Because the optimum temperature and the duration of the heat treatment are not well defined, the boron ore acts as a calcined clay mineral and is discarded along with the gangue. It is important to predict such parameters using mathematical formulations. Thus, a mathematical model is used to predict the required temperature and duration period prior to heat treatment. In the experimental study presented here, a series of systematic thermal tests was carried out in a muffle furnace. Two variables, temperature and time, were studied in a response surface design. A quadratic regression model was chosen and regression coefficients were calculated. Using a regression equation, the volume expansion of the particles in various circumstances can be predicted. The mathematical test results are then correlated with the experimental results to relate the optimum expansion of borax with heating time and temperature and with borax grades and recoveries.

Jan 1, 2008

By Sam F. Carter

FOR some time melters and metallurgists have recognized the fact that steels may be made to identical compositions as ordinarily analyzed, but with considerable variations in physical properties. Good melting practice signifies a combination of furnace operations that will produce steel with consistently good physical properties after proper consideration of cost, production efficiency, and chemical control. In acid practice, these operations may be classified fundamentally as: (I) the oxidizing boil, (2) recarburization and deoxidation, (3) slag adjustment, and (4) final deoxidation. These operations affect the properties of the steel through variations in the minute quantities of several microscopic, submicroscopic, and dissolved constituents, which are out of reach of ordinary analyses but are very influential upon the crystallographic slippage and the molecular cohesion of the structure. One of these constituents is the FeO left in solution in the steel. Herty has shown that steels high in dissolved FeO have decreased ductility and impact and increased hardness and electrical resistance. There is also much evidence that FeO in solution affects carbon solubility and diffusion, and consequently abnormality and carburizing behavior.

Jan 1, 1947

By Cyril Stanley Smith, Earl W. Palmer

STRIP of any of the metals used for deep drawing operations occasionally yields cups that are defective because of a rim that varies in height around the cup in a wave-like manner Some such defects are traceable to tools or other press factors, but when the protuberances formed (usually four in number on brass and other copper alloys) are symmetrically disposed with respect to the rolling direction of the strip, they are invariably attributable to the metal The effect is known as "caring" and the protuberances are called "ears" Other terms frequently heard are "tips," "scallops," and "corners " It is recognized that the effect is most commonly a result of a directional crystal structure produced by rolling and annealing operations in the manufacture of the metal strip Numerous papers dealing with various aspects of the caring effect have appeared in the literature, those listed in the references' being especially interesting and valuable An investigation of the factors influencing caring of brass cups has been in progress in the laboratories of the American Brass Co for several years, and it was thought desirable to make some of the results generally available in summarized form The present paper discusses many factors that do and do not contribute to ear formation In addition, a section is devoted to methods of minimizing the caring tendency of brass sheet by proper selection of the cold-rolling and annealing schedule by which it is produced In the space available, it is impossible to quote detailed experimental procedures and numerical results However, the authors make no statement that they do not believe to be properly substantiated, either by experimental evidence obtained under laboratory conditions or by experience in the actual production of deep-drawing brass in the brass mill MECHANISM OF EAR FORMATION It must be clearly understood that the formation on cups of symmetrical ears, four or more in number, is attributable solely to the strip metal, and results from the strip having different deformation characteristics in different directions The tools used in the drawing process, or the type and completeness of lubrication of the strip, have nothing to do with the problem of ears, although they do, of course, greatly affect the "drawing quality" of the strip and the general appearance of the cup A single tip may be drawn up on the rim of a cup because of misalignment of the tools, or because the gauge of metal varies from side to side of the strip The two-ear form that sometimes appears is also traceable to gauge variations However, the four-ear and six-ear symmetrical forms that we are concerned with here are caused by factors inherent in the structure of the metal itself

Jan 1, 1942

By Cyril Stanley Smith, Earl W. Palmer

STRIP of any of the metals used for deep drawing operations occasionally yields cups that are defective because of a rim that varies in height around the cup in a wave-like manner. Some such defects are traceable to tools or other press factors, but when the protuberances formed (usually four in number on brass and other copper alloys) are symmetrically disposed with respect to the rolling direction of the strip, they are invariably attributable to the metal. The effect is known as "earing" and the protuberances are called "ears." Other terms frequently heard are "tips," "scallops," and "corners." It is recognized that the effect is most commonly a result of a directional crystal structure produced by rolling and annealing operations in the manufacture of the metal strip. 'Numerous papers dealing with various aspects of the earing effect have appeared in the literature, those listed in the references1 being especially interesting and valuable. An investigation of the factors influencing earing of brass cups has been in progress in the laboratories of the American Brass Co. for several years, and it was thought desirable to make some of the results generally available in summarized form. The present paper discusses many factors that do and do not contribute to ear formation. In addition, a section is devoted to methods of minimizing the earing tendency of brass sheet by proper selection of the cold-rolling and annealing schedule by which it is produced. In the space available, it is impossible to quote detailed experimental procedures and numerical results. However, the authors make no statement that they do not believe to be properly substantiated, either by experimental evidence obtained under laboratory conditions or by experience in the actual production of deep-drawing brass in the brass mill. MECHANISM OF EAR FORMATION It must be clearly understood that the formation on cups of symmetrical ears, four or more in number, is attributable solely to the strip metal, and results from the strip having different deformation characteristics in different directions. The tools used in the drawing process, or the type and completeness of lubrication of the strip, have nothing to do with the problem of ears, although they do, of course, greatly affect the "drawing quality" of the strip and the general appearance of the cup. A single tip may be drawn up on the rim of a cup because of misalignment of the tools, or because the gauge of metal varies from side to side of the strip. The two-ear form that sometimes appears is also traceable to gauge variations. However, the four-ear and six-ear symmetrical forms that we are concerned with here are caused by factors inherent in the structure of the metal itself.

Jan 1, 1942

By Shize Jin

Effect of four polyols, namely ethylene glycol (EGL), glycerol (GCL), propanediol (PDL), butanediol (BDL) and three organic acids, namely oxalic acid (OA), malonic acid (MA) and succinic acid (SA) on the current efficiency (CE) and the cell voltage during zinc electrowinning was studied. Galvanostatic polarization was conducted in a supporting electrolyte (SE) containing 180 g dm-³ H2SO4, 60 g dm-³ Zn2+ and 8 g dm-³ Mn2+ at 38°C with magnetic stirring. The imposed current density was 50 mA cm-². The anodes were made of a Pb-Ag alloy and the cathodes were made of an aluminum alloy. The results showed that all the polyols tested in this study decreased the current efficiency and the cell voltage, but the decrease of the cell voltage was not important. Oxalic and succinic acids decreased the current efficiency to a less extent than the polyols, but did not decrease the cell voltage much. The only compound that increased the current efficiency was malonic acid, and its capacity of decreasing the cell voltage was the highest within the seven tested organic compounds.

Jan 1, 2003

By H. A. Bilgin, G. G. U. Aldas

"Ground vibration is the natural result of the blasting process. Many empirical formulae and methodologies including analysis of travel path effects have been developed. The scaled distance, which is the most popular approach for the calculation of the attenuation of particle velocity in the ground, has led to significant advances in the prediction of particle velocity when both explosive charge and distance vary. However, this approach does not consider the effect of ground anisotropy and existence of structural geological features on ground vibration. Therefore, in this study, the effects of these rock mass properties on types, amplitudes, and frequencies of ground vibration waves at four surface mines are examined. The results, which were implemented at Kangal coal mine, Bastas quarry and Kíbrís quarry, provided guidance for the extensive study at Orhaneli surface coal mine.As a result of the study, the authors came to the conclusion that vibration amplitudes change depending on the ground on which sensors were deployed and the conditions depending on whether measurements were done near major structural geological features. It was determined that the vibration amplitudes, measured at equal distances from the source but in different directions, change because of the propagation velocity anisotropy. Besides the change of wave type due to the kind of ground at the measurement location, it was determined that vibration anomolies were due to structural features."

Jan 1, 2004

By V. Cvetkovic, L. Zou, L. Jing

"Sorption process plays a significant role for solute retardation in rock fractures. In this paper, for the aim to investigate the effect of sorption on solute transport in a single rough fracture, a 2D model of representative single rock fracture was built and its roughness was statistically characterized based on the measured data of rock surface topography by laser scanning. A Finite Volume Method (FVM) code was developed to solve the Navier-Stokes (NS) equations and transport equation for numerical modelling the process of fluid flow and solute transport in the rock fracture model. Two groups of simulations were conducted: with and without the consideration of the sorption process with different average flow velocities. The results show that the surface roughness increased the complexities of flow fields, and the non-linear sorption process plays a significant role in the retardation of solute transport through rock fractures. The sorption process caused an obvious lagging time in both the solute concentration fields (plumes) and corresponding breakthrough curves. This lagging time increases with the distance from the inlet boundary, and relatively decreases with the increase of mean velocities. INTRODUCTIONFluid flow and solute transport in fractured rocks is an important research topic for performance and risk assessments for rock engineering projects concerning geo-environment safety, such as radioactive waste disposal, mining, geothermal extraction, reservoir engineering and other contaminant transport processes in geosphere (Berkowitz 2002).The solute transport in the rock fractures mainly involve the advection, surface sorption, matrix diffusion, dispersion, radioactive decay and chemical reactions, governed by general transport equations (e.g. Bodin et al., 2003). Among these transport phenomena, the sorption on the fracture walls can alter solute migration between the fractures, and play an important role in natural retention of solute transport (Weber et al., 1991; Wels et al., 1998; Kumar 2007; Dai et al., 2012). The aim of this study is to investigate the effect of sorption on the solute transport in a single rock fracture with rough surfaces. More complex transport processes, such as matrix diffusion, dispersions, radioactive decay and chemical reactions, are not included in this study."

Jan 1, 2015

Effect of Spacer Chain Length on the Flotation of Kaolinite and Quartz by Using Gemini Surfactants as Collector

Sep 13, 2010

By A. W. Khair

Laboratory studies indicate that the specimen size influences the compressive strength of coal significantly. In the past, the diameter/height ratio of coal and rock specimens with different geometry and its influence on failure characteristics was discussed (Khair, 1993; Khair, 1994; Khair and Xu, 1994). In the current attempt, tests are designed and carried out under uniaxial condition in the laboratory to investigate the influence of specimen size. Cubical specimens of coal with edge dimension ranging from 5 cm (2 in.) through 20 cm (8 in.) were prepared according to the standards and tested uniaxially. Results show that compressive strength of coal is dependent on specimen size until certain level and later the change in specimen size would not yield significant change in compressive strength. Cubical specimens were chosen for testing because they are not only in close resemblance to underground pillars, but they are also the most stable shape under loading. The failure characteristics of these specimens were analyzed and their applicability to pillar design aspects in coal mines is studied. A detailed analysis of the physical and mechanical properties of the tested coal seam is also presented.

Jan 1, 1996