Search Documents

By Ernest A. Draeger, James W. Collins

Water only cyclones, sometimes referred to as hydrocyclones, are one of the newest types of coal processing equipment. These devices have achieved wide acceptance as fine coal cleaners in the past decade. Many metallurgical coal plants employ water only cyclones to process 0.5 mm x 0 size coal. Some of these plants have as many as 40 to 50 305-mm-diam units with each unit receiving as much as 9 t/h of raw feed. The growth in the utilization of hydrocyclones is due partly to the energy shortage, partly to the general increase in over-all coal preparation, and also because of a need for a simplified fine coal (0.5 mm x 0 size) gravimetric separator. Large diameter water only cyclones are also available and in use to process feed sizes up to 32 mm in size. However, the size normally employed for cleaning 0.5 mm x 0 coal are 356 mm or 305-mm-diam for single-stage circuits. In two-stage circuits, the secondary units are normally the same diameter as the primary units or smaller, such as 203-mm-diam. By using the small diameter cyclones and treating a closely sized feed, 0.5 mm x 0 only, it has been found that the probable error or imperfection of the water only cyclones is comparable to that obtained on the same size fraction treated in a large 610-mm-diam heavy media cyclone washing 38 mm x 0. The water only cyclone can approach the efficiency of a heavy media cyclone when cleaning fine solids because it creates its own dense media by accumulating high specific gravity particles in the wide angle conical section of the cyclone. A cut-away cross sectional view of a water only cyclone is shown in Fig. 1. It is also true that when treating a wide range of sizes (38 mm x 0) in heavy media cyclones, the smaller size particles (0.5 mm x 0) separate in proportion to the split of the media through the cyclone rather than by particle density.

Jan 8, 1980

By Matt Kilburn, Liming Lu, Steve Suthers, Alexander Edenton, Rodney Smyth, Matt Adam

"Magnetite concentrate is naturally good for pelletising. However, due to the depletion of reserves of traditional high grade hematite iron ore worldwide, the usage of magnetite concentrate in sintering is expected to increase substantially. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. This will not only improve the quality of agglomerates produced, but also have a potential beneficial impact on the fuel consumption of the agglomeration process. There are an increasing number of magnetite projects currently being considered and developed. However the concentrates from some of these projects are too coarse as pellet feeds and much finer and denser than normal sinter feeds. Accordingly, special strategies are required in order to utilise the coarse magnetite concentrates at high proportions in pelletising and sintering. This paper discusses various raw material preparation technologies and blending optimization methods demonstrated to be effective for improving the sintering and pelletising performance of coarse magnetite concentrates. Pre-granulation and addition of binders, such as hydrated lime, were found to be particularly efficient in recovering the sintering productivity of sinter blends containing magnetite concentrates. In pelletising, HPGR (High Pressure Grinding Rolls) grinding enabled production of good quality pellets from 100% magnetite concentrates and optimized blends containing up to 70% magnetite concentrates also formed good pellets.INTRODUCTION Magnetite concentrates are often used as feed materials for pellet plants or sinter plants depending on their grades and grain sizes. To achieve the required quality of green and fired pellets, the concentrates often need to be ground very fine (80% passing 38- 45 m), which inevitably consumes a great amount of energy. Therefore, efficient grinding processes are required to reduce the amount of energy consumption needed to achieve the sizing and chemical specification of pellet feeds. The use of magnetite concentrates in sintering has the potential to improve sinter chemistry, which is deteriorating over time due to the slowly decreasing grade of direct shipping iron ores around the world (Yang and Mathews, 1997; Yang and Witchard, 1998, Yang and Davis, 1999; Yang 2005). However, methods are required to allow the utilisation of high levels of concentrates in sintering while maintaining productivity and sinter quality (Han and Lu, 2017)."

Jan 1, 2018

By F Mavroudis, M Gaastra

Due to the increasing demand for resources worldwide, efficient utilisation of raw material deposits and recycling technologies become more and more important. Growing industrial nations and increased living standards require a large raw material supply. Hereby responsible handling of existent primary and secondary raw materials is indispensable. By utilising state-of-the-art technologies resources are extracted, recovered and recycled more efficiently which increases sustainability. Hereby sensor technologies combined with intelligent data processing systems in particular provide a considerable research area. Innovative sensor technologies are already implemented during recognition of material-specific characteristics, during elemental recognition as well as during machine control. They are applied to attain increased automation levels of mining machineries, higher recoveries during mining and processing as well as higher recoveries. To be able to face the increased demand for sensor technologies and the integration into raw material industries, an interdisciplinary association of three RWTH Aachen University Institutes has been founded. The association has expertise on increasing productivity and capacity utilisations by automating mining and recovering processes by sensor technologies. Due to the utilisation of sensor systems, materials and structures can now be detected and elementary analysed on a real-time scale. The developed and enhanced techniques are the key for any ambition of autonomous plants and machineries. This paper gives an overview on the regarded sensor technologies for material recognition, machine automation and mineral processing. The authors present concepts based on extensive laboratory and field studies of successful implementation and application the technologies considering special mining conditions. Overall three applications are described to demonstrate the potential of sensor technologies for autonomous and sustainable mining: real-time analysis: recognition of elementary compounds during extraction processes; multi-sensor system EiControlPlus: designed for automation of longwall shearers by complete detection of the machineÆs environment; and sensor-based sorting: applied in recycling and mineralÆs industries.

Sep 26, 2011

By Gupta R. C

Direct reduction of iron ore by solid reducing agents have been studied extensively and summarised by several authors (Otsuka and Kunii, 1969; Abraham and Ghosh, 1979; Frauhan, 1977; Rao, 1971; Kawasaki, Sanscainte and Walsh, 1962; Ghosh, 1970; Rao, 1979). While studying the reduction behaviour, it is generally agreed that the reduction occurs via gaseous intermediate, generated by carbon gasification reaction which involves mass transfer, heat transfer nucleation and growth, etc through a) reduction reaction occurring at solid reductant, and b) reduction reaction occurring at solid iron oxides, thus making the overall reduction process very complex in terms of clearly defining the reduction kinetics of the system. In addition to this, practical difficulties like correctness of reaction temperature, (Seaton, Foster and Velasco, 1983) difficulties in isothermal temperature studies of reduction, difficulties in monitoring the reduction process while using gaseous reductants and separation of reduction by volatile matter from overall reduction process make the reduction kinetics more complex (Misra).

Jan 1, 1999

By D. Harrington

EFFICIENT ventilation of metal mines consists in having such complete control of air currents that. there is always supplied at places where men work sufficient moving air to allow working at maximum capacity without injury to health; and in case of underground fire or of surface fire in the vicinity of mine openings, underground air currents may be quickly reversed if desired, or air may be sent into or excluded from any region and fire fumes confined to only part of the mine workings, instead of penetrating practically the entire mine. Health and safety of workers in mines as well as proper safeguarding and operating efficiency of mining properties are so intimately associated with proper ventilation of mines (both coal and metal) that they are inseparable, yet mine ventilation is only too frequently neglected, especially in metal mines. The metalliferous operator, generally not confronted with inflammable gas or explosive dust which so frequently force ventilation of coal mines, usually disregards air supply altogether except such as may be obtained from compressed air; and generally, even when attention is given to metal-mine ventilation, the air currents rarely are found where they are needed, namely, the working places, especially the working faces. After several years' study of miners' consumption, the writer is. convinced that long continued breathing of air impregnated with large quantities of any kind of finely divided dust, such as is found in a large number of the working places of our mines, will ultimately produce some respiratory disease, whether it be asthma, bronchitis, or phthisis; and the progress of these diseases is hastened. if there are also present high temperatures, high humidities, or harmful gases or if there is present (and allowed to remain to be breathed) large quantities of the finely divided dust when air temperatures are low, hence favorable to maximum performance of work with accompanied maximum breathing into the respiratory passages of the harmful material. It is generally accepted

Jan 2, 1922

By W. Graham

"IntroductionEFFLORESCENCE is herein considered to be any deposit of salts on the surface of a masonry structure that is brought from within or through the structure by capillarity and deposited by evaporation. Usually, efflorescence is white although green, yellow, and brown efflorescence is sometimes observed.The common white efflorescence almost always consists of sulphates of the alkali and alkaline earth metals and calcium carbonate, although sodium chloride is frequently present in structures erected near the sea shore.The first and most obvious result of the presence of soluble salts in masonry is the unsightly accumulation of these salts on the surface. This is particularly noticeable early in its life and is frequently fugitive ( 1), as much of the salt is soluble and is gradually washed away by rain. This removal can usually be facilitated by scrubbing; the structure with dilute hydrochloric acid.A more serious effect is the continuous accumulation of soluble salts as a result of ingress of sulphur acids in rain water or water from the ground. This may eventually cause spalling and disintegration by crystallization of salts in the pores of brick and mortar. An example of this type of failure, resulting from the crystallization of calcium sulphate, is discussed by Hardesty (2). Butterworth (3) describes similar failure resulting from •crystallization of magnesium sulphate."

Jan 1, 1954

By LeRoy D. Loy

Would you believe me if I told you the constant battle between Government regulatory agencies and industry could be won by both sides? No, I'm not crazy, nor have I been soaking up any of that fine Kentucky whitelightning. But I have recently been a participant in a battle where both sides won. Actually, I'm using the term "battle" loosely because, in reality, it wasn't a battle at all - despite the fact that all the ingredients were there for a monumental struggle; i.e.. government, industry, special interest groups and a controversial issue - the development of effluent limitations. I'd like to tell you about it. Historically, on one side of the battle, government has always been ac¬cused of adopting regulations with limited evaluation of existing technologies; and then with seemingly no regard for the economic consequences. On the other side, industry gets punished by government's harsh actions because of their past "do-nothing" attitude toward pollution control. Recently, this battle seems to be losing steam, because both government and industry are beginning to realize that, ultimately, they both will lose. Even more important is the fact that both sides are, or should be, working for industrial expansion compatible with environmental protection.

Jan 1, 1977

By M. Jele

? Sulphuric acid plant in umbogintwini. ? Double absorption plant, capacity of 550MTPD. ? Build by simon curve during the year 1973. ? Side stream plants such as: ? Liquid SO2 Plant, ? Liquid SO3 and ? Oleum plant

Jan 1, 2009

By S. Subhawong

Following the startup of the zinc plant in Clarksville, Tennessee, in 1978, the original effluent treatment plant did not perform as designed. The sludge, produced in a conventional lime neutralization treatment, settled poorly and began to fill the permitted lined impoundment within two years, well short of the original design capacity. Another sludge pond had to be constructed. This led to a new process modification of the original design. Although the design is still based on the conventional lime precipitation of heavy metals, the current effluent treatment plant has evolved into a hydrometallurgical circuit, capable of producing good quality water without generating sludge. Undesirable elements are bled from the zinc circuit and are rejected through the effluent treatment operations. Wallboard grade gypsum is produced, instead of sludge, and all the gypsum is sold to cement and wallboard plants. This operation also recovers and returns more than 1,500 tonnes of zinc annually to the 105,000 tonne/y zinc plant.

Jan 1, 2000

 Increasing concern about the impact of alluvial mining discharges on the water quality of some West Coast rivers lead to a joint West Coast Gold Miners Associate, Trade and Industry funded study by Water Technology (NZ) Ltd. The objective of the study was to assess the treatability of West Coast alluvial gold mining discharges and to develop simple treatment systems which could be effectively adapted to a variety of sites in the region.   The approach was to apply standard water treatment techniques to field situations using low cost technology. Initially the various types of alluvial gold mining operations were identified then after preliminary site investigations and laboratory studies were carried out, site pilot plants were set up. The results of the trials particularly those using chemical aids were encouraging and it was found that chemical aid performance was largely dependent on the degree of mixing at and downstream of the chemical addition point. Design alterations to settling pond configurations in conjunction with optimised chemical addition yielded dramatic results in the form of reduced effluent turbidities.   A generalised approach to effluent treatment was developed and some of the specific 'mix and match' requirements were identified for different types of sites. The general conclusion is that improved physical treatment combined with good plant management and operation and (where necessary) chemical treatment, will produce water of acceptable discharge quality.

Jan 1, 1989

By A. N. Veltmeyer

"INTRODUCTIONTeck-Corona Operating Corporation's David Bell Mine is located 35 Km east of Marathon, Ontario. In conjunction with its 1000 tonne per day gold concentrator, the company operates an effluent treatment plant for the treatment of mill, mine and site effluents prior to environmental discharge. This paper provides a brief overview of treatment strategies and methods, employed to detoxify final effluent.WATER MANAGEMENTThe tailings impoundment basin, located 3 Km south of the plant site, provides storage capacity for all process effluents and site run-off. Basin supernatant (reclaim water) is recirculated to the plant for reuse as process water, in order to minimize fresh water consumption. As site run-off and limited fresh water intake exceed natural losses due to evaporation, reclaim water in excess of process requirements is passed through the effluent treatment (ET) facility to control tailings basin level by providing regulated discharge of environmentally acceptable effluent. (Figure 1)PASSIVE TREATMENTTo reduce treatment costs and burden on the ET facility, reclaim water is fed to the plant to take maximum advantage of natural destruction processes occurring in the tailings basin.These include: volatilizationphotodecompositionbiological oxidation and precipitationstorm water dilutionConcentrator recovery techniques (Figure 2) are directed toward maximizing gold recovery while limiting the addition and extraction of contaminants requiring disposal and eventual treatment.Currently ore ground to 90% -200 mesh is pre-aerated at pH 9.0 with lime for 18 hours prior to 30 hours cyanidation at pH 9.5 with low cyanide ion excess (70 ppm).Pre-aeration passivates cyanicides prior to cyanide contact. This reduces cyanide consumption and the formation of cyanide complexes. In conjunction with recovery requirements low pH is maintained to retard the dissolution of stibnite into its antimony and sulfide components."

Jan 1, 1989

By Plamer D. J, Newman O. M G

The Effluent Treatment System at Pasminco Metals - EZ (PMEZ) was commissioned in December, 1991 and has operated satisfactorily, ensuring that aqueous discharges from PMEZ comply with the Tasmanian Environment Protection Act. The system treats both spills and run-off from the Zinc Plant, and acidic liquor generated in the gas cleaning section of the Sulphuric Acid Plant. The spills and run-off from the Zinc Plant are collected in a large catchment pond. The pond liquor, after partial neutralisation with sodium hydroxide to pH 4, and removal of suspended solids, is preferentially recycled to the Zinc Plant, for example, for washing of residues. Liquor which cannot be recycled, is treated in the Lime Neutralisation Section. The other input to the Lime Neutralisation Section is the acidic liquor from the Sulphuric Acid Plant from which mercury has been removed by contact with aluminium pellets in a fluidised column. In the Lime Neutralisation Section, the liquors are blended and neutralised to pH 10 by the addition of slaked lime. The heavy metals and most of the fluorine are precipitated. The precipitated solids are removed in a thickener with part of the thickener underflow being filtered. Most of the thickener underflow is recycled to generate solids that settle rapidly and filter well. The filter cake is returned to the Zinc Plant for the recovery of contained heavy metals while the thickener overflow is discharged to the Derwent River.

Jan 1, 1993

By Trevor Yeomans, David Yaschyshyn

"Placer Dome (CLA) operates the 90-year-old Dome Mine, in South Porcupine, Ontario.The milling operation currently processes 5 million tons of ore per year, from both the underground and Open pit mining operations, producing 320 000 ounces. The milling process is conventional crushing and grinding, with gold recovery by gravity followed by leach/CIP.Cyanide tailings are impounded in a large (325 ha) tailings area where cyanide is allowed to degrade naturally. Effluent is discharged seasonally during the summer and early fall months to maintain site water balance. Pond water is reclaimed for sole use within the mill process.In 1995, an Effluent Treatment Plant (ETP) was constructed for the purpose of removing dissolved metals and suspended solids. In 1997, an INCO S02/Air cyanide destruction module was added.During this time period, the treated effluent often failed toxicity tests required by the Ontario MISA Regulation, even though effluent chemical parameters were below permit limits. Two studies identified ammonia as the toxicant to Rainbow Trout, and free copper as the toxicant to Daphnia magna.From a literature study, and contacts within the Ontario Mining Association, the use of chelation as a final end of pipe treatment step to render any remaining free copper and metal fractions biologically unavailable was considered. Lab and plant scale tests followed.During the 1999 ETP operating season, the addition of the chelant EDTA (ethylene-diamine-tetraacetic-acid) commenced. To date discharged effluent has passed all toxicity tests.The paper will review the effluent treatment history, current effluent treatment plant operation, and detail the use of EDTA for successful toxicity control.History of Tailings Deposition, and Effluent Treatment From 1910 to 1995Over it’s ninety years of operation, the Dome Mine milling circuit has changed from the original 1910 stamp-mill mercury plant, to today’s modem 14 000 ton per day automated gravity and Carbon in Pulp based plant.By the 19803, a modern mill was operating on mainly underground mined ore. The plant was operating at some 3 800 tons per day, using fairly conventional processing routes.The number 4 tailings dam was being used for tailing’s deposition.All effluent treatment was by natural degradation of cyanide. Discharge was from decanting type structures during the summer months only, maximizing the use of natural degradation no tailings effluent was recycled for Mill use."

Jan 1, 2001

By Enrique Velarde

El presente texto señala el uso de Balanced Scorecard, como una de las herramientas más modernas y completas de implementación y control estratégico en la compañía minera Xstrata Tintaya. También se describe su implementación por etapas, los principales atributos del BSC de la gerencia y se presenta las lecciones aprendidas, las dificultades y los resultados logrados. De forma, que la empresa ha desarrollado un recurso para medir, gestionar y monitorear las variables clave como riesgo socio-político, percepción externa, procesos de diálogo y la identificación y ejecución de proyectos de impacto en educación, salud, infraestructura y turismo, al tiempo que esta mejora el alineamiento de la gestión social.

Sep 14, 2009

By Irajá Bernardino Ribeiro Juniorr

O presente trabalho tem por objetivo apresentar alguns exemplos de aplicações na Indústria Siderúrgica e de Mineração (Prensa de Rolos e Torre de Resfriamento) mostrando que com o emprego de uma confiável metodologia para determinação dos benefícios energéticos é possível a implantação das medidas de conservação de energia em sistemas de força motriz instalados nestas indústrias com o simples uso de Lubrificantes Sintéticos Especiais em substituição ao largo emprego de óleos minerais. Esta solução também proporciona ganhos energéticos e financeiros expressivos e mais atrativos do que as já consagradas soluções de eficiência energética como troca de lâmpadas e /ou motores de alto rendimento. Além do mais, a troca de lubrificante já é rotina implementada nas indústrias e seus profissionais da área de manutenção, não sendo preciso treinamento adicional para implementação, tornando esta ação com o propósito de economizar energia simples e fácil de ser implementada. Este trabalho é uma parte dos resultados do projeto inovador desenvolvido pela Klüber Lubrication desde 2010, onde o principal objetivo é disponibilizar aos usuários de sua linha de produtos este recurso, internacionalmente reconhecido, de Medição & Verificação para a comprovação de ganhos de energia em prensas de rolos com alcance de redução de cerca de 10% de consumo de energia.

Aug 17, 2017

By David Fernando de Carvalho

Este estudo de caso foi solicitado por uma grande mineradora brasileira à Chemtech Engenharia, com o objetivo de avaliar um projeto de um Transportador de Correia de Longa Distância na fase conceitual, onde se buscava a otimização do consumo energético, mínimo investimento financeiro inicial e redução dos custos operacionais. O resultado deste estudo de caso foi usado como diretriz no projeto básico do equipamento, além de ser usado como referência para outros projetos similares.

Sep 25, 2017

By Yuri Oliveira Lima, Vitor Furlan de Oliveira, Adriano Gomes de Freitas, Ricardo Borges dos Santos, Luis Alberto Martinez Riascos

O presente trabalho, resultante da parceria público-privada entre a empresa Zeppelin Systems Latin America e a Universidade Federal do ABC, tem por objetivo validar o desempenho em termos de taxa de transporte e consumo energético de um vaso de pressão não convencional, o equipamento atua como alimentador de sólidos industrial para transporte pneumático, desenvolvido para operação de transporte de materiais em fase densa. Calcário é usado como material de deslocamento durante os ensaios no Centro de Testes da empresa, foi verificado que o novo injetor pressurizado tem menores dimensões e complexidade de operação, e possui taxa de transporte e consumo específico efetivo equiparáveis às versões de vasos de pressão convencional.

Aug 1, 2019

By Jaqueline Couri Rolim

Com o mundo globalizado, surgiu a necessidade de um novo ordenamento em termos de espaços produtivos e de dinâmicas comerciais, acarretando novos paradigmas nos sistemas portuários, em especial nas cidades com portos. Partindo-se da premissa que os portos apresentam não somente caracteres técnico-operacionais, e sim representam instrumentos a serviço do desenvolvimento, interligando sistemas de cidades e fortalecendo economicamente uma região, buscou-se descrever os principais aspectos de um sistema portuário em geral, apresentando exemplos de portos eficientes mundialmente. Foram, também, avaliados os impactos e interações com as cidades, e as condições necessárias aos portos. Objetivou-se identificar, especialmente para a cidade do Rio de Janeiro, o estado da arte do porto, bem como apresentar uma postura mais moderna e descentralizada com relação à gestão portuária. Considerou-se a importância que este porto agrega para o país, porque as atividades econômicas desenvolvidas em um raio de 500 km são responsáveis por 67% do Produto Interno Bruto (PIB). A metodologia utilizada neste trabalho foi pesquisa bibliográfica, exploratória em documentos com conteúdo atualizado sobre o tema proposto. As análises do conteúdo foram levantadas de forma indutiva. Como resultados, ressaltou-se a possibilidade de implantação de uma nova tecnologia de automação utilizada em vários portos do mundo, que prioriza a agilidade nas conexões que transportam bens ou serviços, tornando mais eficiente e eficaz os processos relacionados a porto-cidade. Foram também abordadas e propostas melhorias nos aspectos relativos a uma possível modernização na infraestrutura, na logística portuária, nos fluxos, nos aspectos socioeconômicos e nas políticas públicas, com intuito de melhorar a produtividade portuária, apontar soluções para o desenvolvimento e para a reaproximação do Porto do Rio de Janeiro com a cidade.

Aug 16, 2017

By Harold Paredes D

El presente texto señala el comportamiento químico de las principales impurezas de los iones metálicos y no metálicos provenientes de los efluentes líquidos de la industria minera durante el proceso de potabilizacion de agua. Es importante que el tratamiento aplicado a los micro u oligoelementos de dicha potabilización del agua, garanticen que los contenidos de sus concentraciones no sean nocivos para la salud, así como que la calidad del efluente líquido de las plantas de beneficio se corresponda a un bajo precio y garantice una óptima potabilización del agua.

Nov 8, 1984

By E. Yan

Electrostatic separation has been a mainstay of minerals sands flowsheets for over 50 years. Recent electrostatic developments have shown better conductor/non-conductor separation than technology previously available. Results to date show significantly increased separation efficiency over prior-art high-tension roll electrostatic separator (HTR). These improvements allow greater simplification of MSP circuits by minimizing re-circulating loads. The distinct features of the eForce include: 1) A provision that minimizes the affects of particle size to improve separator performance, 2) an enhancement of the design and arrangement of the static electrode providing a greater attraction force for separating fine conductive particles, and 3) inner roll and outer plate electrode configuration to improve separation efficiency and throughput capacity. Key Words: eForce, Electrostatic, Ion bombardment, HTR, Separation Efficiency, Electrostatic Classifier

Jan 1, 2003