Search Documents

By M. Fan, R. Letkiewicz, A. Hobert, J. Milbourne

Ultrafine copper, gold and silver minerals flotation has become increasingly important because of the rising demand for processing finely disseminated ores. This paper investigates the improved flotation of ultrafine ores from a Troilus Gold project. Troilus is primarily an Au-Cu deposit but contains minor amounts of Ag, Zn and Pb, as well as traces of Bi, Te, and Mo. As a result of ultrafine Cu-Au-Ag dissemination and associated grinding requirements, Eriez’ column/StackCell and Denver benchtop cells were utilized to optimize their respective flotation responses. Enhanced flotation results were achieved using column and StackCell technologies. KAX 51 and SPRI 206 collectors, Na2SO3, and ZnSO4 depressants were the primary reagents employed. In column/StackCell flotation of three main mineral deposit ore composites, the rougher-scavenger-cleaner circuit Cu, Au and Ag flotation recoveries were 90.4~95.8% at a copper grade of 13.6-17.4%, 87.5-95.1% at a gold grade of 101-145.9 g/t, and 88.6-91.8% at a silver grade of 62.6-251.4 g/t, respectively. The benefits of Eriez Column/StackCell flotation technologies include high flotation selectivity and increased recovery due to unique hydrodynamic designs. Specifically, the StackCell design facilitates high turbulent kinetic energy dissipation rates to improve fine particle recovery and incorporates countercurrent wash water to significantly reduce hydraulic entrainment of the finest size gangue minerals to the froth product.

Feb 1, 2023

By C. L. Jiang, B. K. Parekh, X. Shao

Among the impurities present in phosphate ore, dolomite is the most difficult to remove. This is because dolomite and phosphate have similar chemical compositions and because the dissolved species of dolomite is adsorbed on the surface of the phosphate mineral. A new amphoteric surfactant was found to be a suitable collector for the separation of dolomite and phosphate. Flotation results showed that the new amphoteric collector had a high flotation selectivity for dolomite over a wide pH range. studies on the flotation of francolite and dolomite in each other's supernatant demonstrated that the dissolved ions had little effect on the selectivity of the new collector. It was found, however, that the dissolved ions were detrimental to the flotation separation using sodium oleate as collector. From a mixture offrancolite and dolomite containing 26.2% P2O5, a phosphate concentrate containing 35.2% P205 with a 90% recovery was obtained using 290 g/t of the amphoteric collector. The rejection of MgO was 81.41 %.

Jan 1, 1999

By N. S. Dalal, J. F. Mega, X. Shi, V. Vallyathan

Several studies have suggested that pulmonary toxicity to asbestos and silica may be mediated through oxidant-induced cell injury. We have reported recently that surface radicals associated with freshly fractured silica may be an imponant factor in cell injury and induction of pulmonary disease. Although the generation of oxygenated radicals in dust-cell interactions has been demonstrated, there are no data correlating the toxicity of a dust with the level of oxygen radical generation by the dust during its interaction with phagocytic cells. In the present study, we have investigated the in vitro generation of oxygen free radicals from human neutrophils and rat alveolar macrophages stimulated with freshly fractured silica, aged silica, amosite, crocidolite, chrysotilc, and a nontoxic dust, barite. Electron spin resonance (ESR) with the aid of a spin trap phenyl-N-ten-butyl nitronc (PBN) was used to measure the oxygen radicals generated during phagocytosis of the dusts. The relative toxicity index and ESR peak heights, on an equal surface area basis and normalized to barite as one, showed a direct relationship. The normalized toxicity indices and peak heights were: silica, 3.5 versus 2; chrysotile, 4 versus 2; crocidolite, 11 versus 8; and amosite, 26 versus 13. Addition of hydroxyl radical scavengers such as catalase, dimethyl sulfoxide, 1,3 dimethyl-2-thiourea (DMTU), sodium benzoate, and mannitol prevented the radical generation. Carmustine, a glutathione reductase- glutathione peroxidase inhibitor, caused a 5-fold increase in the radical generation. These results indicate that a nontoxic dust such as barite generates toxic oxygen radicals at a minimal level that can be quenched by the normal cellular defense system. For toxic dusts such as silica, amositc, chrysotile, and crocidolite, the potential for oxygen radical generation is enhanced by their surface propenies, physical dimensions, and the surface-based radical-generating redox sites. The enhanced radical generation may impair the cellular defense system, resulting in cell injury. Use of scavengers, chelators, and potentiating agents suggests the membrane-based oxidase system as the probable primary source of the radical-generating system. The data presented herein suggest the generation of oxygen free radicals as an important primary event in silica- as well as asbestos-induced cell injury.

Mar 1, 1992

By K. Osburn

South Deep Gold Mine, owned by Gold Fields Ltd., is situated near Westonaria in the Gauteng Province of South Africa and mines the conglomerate bands of the Upper Elsburg reefs (Mondeor Conglomerate Formation) of the Witwatersrand Supergroup and the Ventersdorp Contact Reef (VCR) of the Ventersdorp Supergroup. The stoping and underground developments are mechanized. The Upper Elsburg reefs are mined by a variety of mining methods, including mechanized drift and fill, modified drift and bench, longhole stoping, and low-profile mining. Optimal mine design and scheduling for deep-level mechanized mining are complex, and success is highly dependent on detailed, robust, and accurate geological and geostatistical models. Geological structures significantly influence the sedimentological characteristics, distribution, and preservation of the Upper Elsburg reefs and VCR. Accordingly, particular emphasis is placed on the generation of a mine-scale structural model that accommodates the relationships between the older north-trending fault systems (West Rand and Panvlakte faults) and younger east-trending dextral wrench faults. Results from underground mapping, borehole intersections, and highresolution three-dimensional seismic data have been integrated to produce coherent three-dimensional geological models. The Upper Elsburg reefs suboutcrop against the VCR and comprise an easterly diverging clastic wedge, thickening from the suboutcrop position, to approximately 130 m at the mine?s eastern boundary. The Upper Elsburg reefs are characterized by conglomerate and quartzite bands forming multiple, stacked, upward-fining unconformity-bounded couplets. Palaeocurrent directions are dominantly from west-northwest to east-southeast, indicating that the more proximal deposits are preserved close to the suboutcrop, with distal facies to the east. Sedimentological modelling is applied to individual stratigraphic units and caters for facies definition. This is achieved through channel width (CW) kriging and fitting of type sections to borehole and mapping data. Homogenous geological geozones for each stratigraphic unit are thus defined within individual structural blocks on the basis of those sedimentological parameters that have been found to have a positive spatial correlation to gold concentration. These geozones then serve as constraints to the evaluation of the orebody. This contribution presents a summary of the modelling processes that are currently applied in the development of high-confidence, timeously produced geological models that are essential input for mineral resource estimation and mechanized mine planning and scheduling.

Jan 1, 2014

By Mauricio Estrada, Luis Vilchez, Luis Valencia, Marco Vera, Italo Manzo

Flotation is the most used separation process worldwide. Flotation characterization is usually carried out in batch conditions at laboratory scale. A phenomenological description of the flotation process is challenging, however, the evaluation of flotation performance in a contextual manner by means of a pilot plant is beneficial to reduce uncertainty on metallurgical results. In addition, leveraging pilot plant results by digitalize them helps describe the process dynamically. Consequently, flotation pilot plant testing allows a Digital Twin (DT) to be generated by combining ore characteristics, process information and a digital architectural platform. Therefore, the generation of a Digital Twin of the flotation pilot plant provides a tool to explore and evaluate new operating scenarios. This allows an optimum scenario to be identified and scaled up (i.e., industrial operation).

Sep 30, 2022

By D. T. Jordan, L. C. Coetzee, G. Kalenga, T. Mahlangu, W. J. Shipman

Although online free cyanide analysers are widely available and used in gold leaching operations worldwide, reliable automated free cyanide concentration control is not consistently achieved in many of these operations. Effective cyanide concentration control is complex owing to amongst others, the long residence times and ore feed variations. Model Predictive Control (MPC) has been proven to provide superior cyanide concentration control over traditional proportional-integral-derivative (PID) control, leading to savings in operational costs and reduced leachable gold losses. In the first example reported in this paper, MPC has improved control of the free cyanide concentration by keeping it within the required range 73% of the time during testing, compared to the previous PID controller that only achieved this target 30% of the time. This represents a 143% improvement. Another example demonstrates a 22% reduction in cyanide usage as a result of using MPC. MPC functionality is rarely available on the programmable logic controllers (PLCs) and control systems installed at gold plants, hence it is implemented on a personal computer (PC) networked to the cyanide analyser and plant infrastructure. Mintek has developed an embedded MPC that installs into the Mintek Cynoprobe analyser, adding MPC functionality without the need for additional PC and network infrastructure, reducing installation costs. This allows plants to minimise their expenditure on additional infrastructure while gaining the benefits of superior MPC technology for multiple cyanide dosage points. This paper will present results showing that the embedded MPC performs as well as Mintek’s existing PC-based StarCS MPC controller, making it a viable alternative for infrastructure-constrained gold plants. Keywords: Model predictive control, gold cyanidation

Jan 1, 2020

By C. S. Caldwell, L. C. Thompson

Mine closure and reclamation issues have evolved over the past several years becoming further complicated by stricter standards and by the cmrent economic climate and price of gold. Many mine permits are calling for more stringent remediation of spent ore heaps and tailings. Leachate solution water quality must meet strict discharge criteria for multiple parameters besides cyanide at mine closure. Closure standards are more difficult to meet and most mines do not have an increased budget at the end of mine life to deal with the falling standards. These issues make additional gold recove1y at the end of mine life a critical problem in financing some closure operations. Another issue is the length of time that must be budgeted for heap rinsing operations. Innovative biological processes developed and applied by Pintail Systems, Inc. at numerous mine closures have indicated that bio-processes can significantly enhance gold recovery dur­ing heap cyanide bio-detox over the recoveries expected from rinse operations. If heap rinsing can be eliminated or reduced and if gold recovery can be improved at the end of mine life, many mine closures may be possible with processes that pay for themselves or generate profit. Additional advantages of the bio­detox technology is that it can be engineered to treat multiple contaminants besides Weak Acid Dissociable (WAD) cyanide. Other contaminants treated in heap process solutions include nitrates, ammonia, heavy metals, thiocyanate and total cyanide. At the Cripple Creek and Victor Mining Company Ironclad Mine near Victor, CO, 5 million tons ofrinsed, heap leached spent ore were biologically detoxified to reduce cyanide content, enhance gold recovery during bio-detox and to reduce dissolved metals in heap leachate solutions. During the bio-detox treatment period a substantial improvement in gold recovery allowed the detox oper­ation to operate as a profit center. Final gold recovery was at least twice what was expected from a normal rinse operation.

Jan 1, 1998

By N. Moony

The benefit of gravity separation in improving total gold recovery in grinding circuits has been outlined in a significant number of papers to date. However, the use of batch centrifugal concentrators (BCC) as an industry standard to extract gold has limited the potential for maximizing gravity recoveries -particularly in coarse gold deposits. This is a reflection of the high upgrade ratios obtained by BCC's which has an inverse relationship with recoveries. Survey work in Australia has indicated that installation of the InLine Pressure Jig as an alternative to the Bee will significantly increase recoveries of gold by gravity and, accordingly, increase total gold recoveries and lower operating costs.

Jan 1, 1998

"Mineral separation by exploiting the differences in mineral or metal specific gravities (sg) has been used since antiquity. In the modern era, this is most commonly seen in the recovery of gold by the use of centrifugal concentrators and the separation of coal (low sg) from waste rock (high sg) using heavy media cyclones and jigs. Other metals, notably oxides of tin and tungsten, are successfully recovered using some combination of jigs, spirals and shaking tables. However, many conventional gravity separation systems are limited to fairly coarse (>1 mm) to medium (>100 micron) particle separations due to the limitations of the gravitational separation forces in conventional equipment.Many of the high specific gravity minerals of interest are friable (e.g. cassiterite, wolframite, etc.) and excessive fines are generated in the grinding/comminution circuits which cannot be recovered with conventional equipment and may be lost directly to the tailings stream. Recent developments in centrifugal gravity separation equipment specifically designed for fine or ultra-fine particle separation and recovery have resulted in heavy mineral particle recoveries as fine as 10-20 microns. Ongoing research work has also identified the benefit of closed-circuit, multi-stage gravity recovery circuits using some combination of centrifugal concentrators and conventional equipment (tables, spirals, flotation, etc.) which can substantially increase overall plant recovery and final concentrate grade.This paper will provide details of the evolution of non-fluidized bed gravity concentrators for high sg mineral recoveries, correlate laboratory scale development work with plant results to confirm scale-up, and show how recent flowsheet developments have contributed to significantly improved plant performance.IntroductionGravity concentration is one of the oldest and most cost effective metal and/or mineral recovery systems, ranging from the classic hand panning of alluvial gold, through to the large scale production of a wide range of metals and minerals, including gold, silver, PGMs, black sands, coal and iron oxides. Conventional gravity recovery systems, comprised of some combination of sluices, spirals, jigs and shaking tables have limited application in fine particle (i.e. <100 microns) recovery, or where there are limited differences in particle specific gravities (sg), e.g. the separation of high sg, high value metal oxides (e.g. those of tin, tantalum or tungsten), from medium sg, lower value metal sulfides such as pyrite and pyrrhotite. These unit operations tend to have limited capacity, and while double and triple turn spirals and multi-deck tables have been developed, extensive floor space is often required in order to process the tonnages incorporated in the modern mineral processing plant."

Jan 1, 2017

By Denis M. Riley, Neville C. Lockhart, Bruce A. Firth

The potential use of the Kelsey Centrifugal Jig to clean fine coal has been studied. It was found capable of cleaning coal at very fine sizes, at least to 0.038 mm at relative densities as low as 1.6. This effect was however very dependent upon the solids feed rate and the absence of significant amounts of clay slimes. Comparisons with a spiral and a laboratory scale Jameson Flotation Cell were made. The concept of recleaning spiral product was investigated. Use of a spiral to reclean the coarse fraction, and a centrifugal jig or flotation to treat the fine fraction, gave significant improvements in final ash values over spiral recleaning of the full size. Future R&D needs include improving feed rate capacity, and application to problems like pyrite removal that are difficult to solve via flotation.

Jan 1, 1995

By B. C. Paul, R. Q. Honaker, K. Ho

Recent research has shown that froth flotation is not effective at treating fine coals (-28 mesh) containing a large portion of middling particles. Due to their relatively large density differences, middling particles can be separated more efficiently using gravity-based processes. The ability of gravity separators to treat fine particles has been limited by the lack of particle inertia relative to the surface drag forces. However, particle inertia can be enhanced by the application of a centrifugal field. A commercial-scale centrifugal Falcon concentrator capable of treating a mass flow rate of greater than 1 tph continuously has been used to evaluate its feasibility for treating fine coal as an alternative to froth flotation. Tests conducted on a -28 mesh fine coal circuit feed have found the Falcon concentrator to be very effective at cleaning the 28 x 325 mesh size fraction. For an Illinois No. 5 coal sample, the ash content was reduced in the 100 x 325 mesh size fraction from about 18% to 8% while achieving a high combustible recovery value of nearly 97%. In addition, the total sulfur content was substantially decreased from 2.6% to 1.7%. The effects of the critical operating parameters on separation performance have been studied and their values optimized.

Jan 1, 1995

By S. Orr

Flow in heaps and dumps is a two-phase flow phenomenon, though for many applications it could be simplified as unsaturated flow. Unlike saturated flow (typical of ground water flow), where permeability is independent of other hydraulic parameters, unsaturated flow permeability depends on the degree of saturation and/or on capillary pressure. Several recent field studies suggest that flows in heaps and dumps tend to concentrate in preferred pathways, bypassing much of the ore. Different preferential flow phenomena are triggered, promoted and influenced by different heap structures, by pretreatment, by the composition of the leach solution and by application rates and schedules. The structure of heaps and dumps is determined and affected by every stage of their construction -from blasting to crushing to conveying and stacking of the material. History of heap construction and operation combined with monitoring, mapping and certain field tests can reveal patterns of flow and transport in a given heap and can shed light on the physical mechanisms behind it. Such insight can provide a first cut on heap leaching enhancement by either eliminating or bypassing physical barriers to flow and leaching. Based on the understanding of the heap structure, advanced flow and transport models can be constructed and further enhance the insight. This insight is essential for understanding cause and effect and can provide a basis for decision making. Further, based on the physically-based models, an intelligent control agent, such as MRDS1, can learn and build a self-learning representation (or a model) of the complex heap leaching system, followed by dynamic optimization and planning of heap leaching and heap rinsing.

Jan 1, 2003

By V. Vesselinov, S. Orr

"Enhanced heap leaching - Part 1: Insights" (Orr, 2002), different flow and transport phenomena that could significantly reduce leaching recovery were investigated. The combination of such understanding with advanced flow and transport modeling establishes the link between cause and effect, thereby, directing operators to optimal design and construction of new heaps. Modeling of flow and transport in heaps could also point to a unique change in application method or rate that would maximize leaching enhancement of an existing heap under existing situation and leaching history. The use of such a model is cost effective in that it can simulate multiple scenarios of alternative leaching enhancement methods. By simulating a large number of irrigation scenarios, such a model can point to the optimal and/or the most promising alternatives for a particular heap. The authors&apos; simulations concentrate on the effects of changes in application rates and heap design on changes in flow paths and enhanced leaching recovery. Based on such simulations, an intelligent control agent, such as Multiple Resolution Decision-Support System (MRDS) (Meystel and Albus, 2002), could build a new representation of the complex heap-leaching system. And, by learning from historical data and current information, it could provide optimal management of heap leaching and heap decommissioning.

Jan 1, 2003

By D. Doepker

The dissolution of metals from various metal/ non-metal mine tailings has been studied through column leach tests at US Bureau of Mines laboratories. Metal mobilization in unsaturated columns was consistently greater than metal dissolution in water-saturated columns. Leachate pH was also frequently lower when a leachant was passed through columns but showed a mixed residence-time dependence. On the other hand, metal and sulfate ion concentrations in the leachate increased with dry-cycle residence time. Results suggest that acid formation through atmospheric oxidation of pyrite may compete with non-acid-forming oxidation of other metal sulfides. The two processes lead to decreased pH and increased metal mobilization, respectively. Leach tests using sodium lauryl sulfate indicated that microbial activity was not a factor in these studies.

Jan 1, 1991

By H. -S. Yoon, C. -J. Kim, K. W. Chung

"With the final goal of ultrasonic application to ion exchange in a resin-in-pulp (RIP) system, the feasibility of an indirect ultrasonic application with a submersed ultrasonic probe was investigated first for the enhancement of ion exchange in the following resin-in-solution (RIS) system: Lewatit MonoPlus MP 600XL in an artificial solution with 106 ppm uranium. Ultrasonic radiation enhanced the ion exchange efficiency without mechanical degradation of resin. For 3.6 g/L of resin, the enhancement was 79 percent after 10 min of ion exchange and it gradually decreased to 11 percent at 60 min. In addition, a preliminary test of the mechanical stability of the resin in the RIP system showed little mechanical fracture of the resin due to ultrasound, which indicates that indirect ultrasonic application by a submersed ultrasonic probe is applicable for RIP systems. IntroductionIn uranium ore processing, the ion exchange process has been used on a commercial scale for preconcentration and purification (Gonzalez-Luque and Streat, 1984). The ion exchange process is divided into two processes: (1) a resin-in-column process with the uranium-bearing solutions passed through columns containing resins and (2) a resin-in-pulp (RIP) process with the leached ore pulp exposed to resins. The latter does not require the separation process of leach liquor and ore solids, which reduces process costs. This process, which has been developed commercially since 1955, has a certain drawback. The adsorption rate and efficiency in the RIP process are relatively low, so numerous contacts between resins and leached ore pulp are needed, which adds to the cost (Merritt, 1971). It is necessary to study methods to reduce process costs.Ultrasound can intensify mass transfer, increase the rate of chemical reactions, and change reaction pathways (Thompson and Doraiswamy, 1999; Luque de Castro and Priego-Capotem, 2007; Adewuyi, 2001; Luque-Garcia and Luque de Castro, 2003). It has great potential in chemistry and is especially considered to be a promising method for enhancing mass-transfer-limited processes, such as ion exchange. Enterzari and Tahmasbi (2009) reported the effect of ultrasound on water softening by ion exchange. Band et al. (1997) proposed a modulated ultrasound application to water desalination with ion-exchange hollow fibers. These reports revealed that ion exchange kinetics could be enhanced by the application of ultrasound. As for hydrometallurgy, Feng and Aldrich (2000) reported that the elution of an ion exchange resin was enhanced by the use of ultrasonication."

Jan 1, 2015

Digitally enhanced Landsat MSS images are being used&apos;in delineating the structural and tectonic features in the Arabian Shield as part of a project funded by King Abdulaziz City for Science and Technology (KACST) of Saudi Arabia. The delineated features together with statistical modeling and structural analysis are to assist in an improved understanding of the evolution and mineralization of the Arabian Shield. Specific emphasis is to be given to relating the extracted linear features to the location of known mineral occurrences and areas of potential geologic hazards. A number of textural (spatial) and spectral enhancement techniques have been applied, to the MSS data covering selected areas, in selecting the most optimal enhancement product for visually delineating the structural geologic .features.

Jan 1, 1988

By O. G. Olvera

"Refractory sulfidic ores consist of materials in which gold occurs finely disseminated within metallic sulfides or forming solid solutions, with pyrite and arsenopyrite being the two sulfides most commonly associated with gold. Typical cyanide operations show poor performance and require oxidative pretreatments to increase gold recovery. Pretreatment alternatives include roasting, pre-aeration, acidic and alkaline high pressure oxidation, and bacterial oxidation. The presence of arsenic, however, introduces a serious disadvantage to the use of roasting and bacterial leaching, while high pressure oxidation involves high capital costs. This work focuses on evaluating the effect of the addition of a carbon resin as a sulfur collector on the oxidation of different arsenopyrite concentrates under atmospheric tank leaching (ATL) conditions. The addition of the resin improved the oxidation of sulfides and favored the formation of elemental sulfur over the generation of sulfate. The use of AF5 in ATL resulted in higher gold recoveries under standard cyanide carbon-in-leach and thiosulfate leaching.INTRODUCTION Refractory sulfidic ores consist of materials in which gold occurs finely disseminated within metallic sulfides or forming solid solutions, with pyrite and arsenopyrite being the two sulfides most commonly associated with gold. Gold is not readily accessible to solutions in these types of ores and typical cyanide operations show poor performance, thus making the use of oxidative pretreatments a requirement to increase gold recovery. Pretreatment alternatives include roasting, pre-aeration, acidic and alkaline high pressure oxidation, and bacterial oxidation. The presence of arsenic, however, introduces a serious disadvantage to the use of roasting and bacterial leaching, while high pressure oxidation involves high capital costs. The use of carbonaceous materials to enhance the dissolution of sulfides is not novel, and leaching additives such as coal, activated carbon and carbon powder have been considered for the improvement of bioleaching, atmospheric leaching, and pressure oxidation leaching processes. However, this type of technology has been focused mainly on the recovery of copper from copper concentrates containing chalcopyrite with less attention paid to other sulfides."

Jan 1, 2017

By A. Miura, R. Winarko, D. B. Dreisinger

Chalcopyrite leaching in acidic ferric sulfate media at ambient temperature exhibits slow kinetics and poor leaching efficiency, which is typically attributed to surface passivation. Recently, the presence of small amounts of iodide in the leaching media has been reported to significantly accelerate chalcopyrite dissolution. To further explore the behavior of chalcopyrite leaching in the presence of iodide, it is essential to determine the factors that control the leaching kinetics. In this study, we investigated the effect of initial solution potential, iodide concentration, particle size, and temperature on the kinetics of copper extraction from chalcopyrite. The key in the experimental setup was to minimize iodide loss by iodine evaporation and precipitation as cuprous iodide. The former was achieved by performing the leaching tests in fully sealed leaching systems. The latter was achieved by maintaining the solution potential higher than 420 mV (versus Ag/AgCl electrode), where formation of CuI precipitate is possible. The experimental results show that higher solution potential and higher iodide concentration had a pronounced positive effect on the rate of chalcopyrite dissolution. There was no effect associated with particle size, which might be due to the narrow size range tested. The positive effect of increasing temperature only manifested itself when the solution potential was sufficiently high. INTRODUCTION The main challenge of chalcopyrite leaching using ferric ions as the oxidant at ambient temperature is the slow kinetics and poor extraction. The reason for this leaching behavior has been attributed to passivation resulting from formation of insoluble passivating layers on chalcopyrite surfaces, which could be metal-deficient sulfides, elemental sulfur, polysulfides, and iron precipitates (Klauber, 2008). To overcome passivation, technologies using higher temperature and pressure have been developed to leach chalcopyrite concentrates, such as the CESL process (Mayhew, McCoy, Mean, & Woeller, 2013), FLSmidth Rapid Oxidative Leach (ROL) process (Mulligan et al., 2017), Galvanox (Dixon, Mayne, & Baxter, 2008), Albion process (Hourn, Turner, & Hourn, 2012), HydroCopper (Hyvärinen & Hämäläinen, 2005), TPOX (Dreisinger, 2006), and AAC/UBC process (Dreisinger, Dempsey, Steyl, Sole, & Gnoinski, 2003). Even though they are effective in accelerating copper leaching kinetics, those technologies typically have higher capital and operating costs associated with production of concentrates and application of autoclaves. This makes them unsuitable for treating low grade primary copper sulfide ores.

Jan 1, 2019

By Jose Hector Figueroa P.

Mexicana de Cananea, S.A de C.V. is a major copper producer mining a large deposit of the disseminated porphyry type considered one of the largest copper resources of the world with 2.7 billion tons of 0.60% copper for the mill plus 4.1 billion tons of averaging 0.26% copper for leaching. Mining of low grade sulfide leach ore, has been an important part of the overall production of the open pit mine which started in 1944. Before this time all the mining in Cananea was by underground methods. The leaching process in Cananea began on the 1920&apos;s with in situ operations in the underground mine and small dumps up to the 1950&apos;s. Large scale leaching operations began in 1960 and the copper solutions produced were treated in precipitation plants until 1,980 when the first SX/EW Plant was put in operation in Cananea. Leaching action is essentially ferric-bacterial, with no fiesh acid added to the leaching solutions. Traditionally, 5540% copper extraction is recovered fiom ROM, 70- 120 meter high leach dumps in 80 months of leaching. Cananea has successfully improved copper recoveries by implementing several actions that include: 1. Stripping of old dumps. 2. Leaching of old dumps through slotted casing. 3. Crushing conveying leach ore to minus 8 inch and stacking it in 30 meter lifts. As result of these actions, copper recovery has been increased&apos; to about 70% of total copper with actions 1 and 2 and up to 85% in half the time by crushing-conveying the leach ore, based on the same solubility index of the run-of-mine ore. This paper describes the above actions that were implemented to enhance the leaching recoveries from. sulfide leach dumps and the economics of such actions.

Jan 1, 1999

By G. Deschênes

In the last 4 years, the high price of silver attracted more interest for improving its extraction. Metallic silver and silver minerals require a high concentration of cyanide and show slow leaching rates and poor extraction. This investigation determined the effects of dissolved oxygen, lead nitrate and a pretreatment on silver leaching from slurry containing quartz mixed with metallic silver and high purity acanthite. Stephanite, pyrargyrite and polybasite were also used in the study. The silver minerals were characterized by chemical assay, X-ray diffraction analysis (XRD), image analysis (MP-SEM-IPS) and electron microprobe analysis (EMPA). Increased dissolved oxygen of the slurry produced the fastest silver leaching kinetics. The leaching of silver from high purity acanthite was determined under various conditions and compared to a new process called ?CANMET Enhanced Leaching Process (CELP). For a slurry containing acanthite, a 23% improvement (from 76% to 99%) in silver extraction was obtained with the CELP. In presence of pyrargyrite and polybasite, silver extraction increased from 75% to 90% and 86% to 99% respectively using the CELP. No improvement was obtained for the slurry with stephanite (99% extraction in 72 hours). However, the sliver leaching rate was much faster with the CELP. XPS analysis of individual silver mineral particles showed that CELP leached surfaces were considerably more oxidized relative to the conventional cyanidation leached surfaces. Leaching of two gold/silver ores indicated that the efficiency of the CELP increased with the refractoriness of the sample. Gold extractions were comparable for the two technologies while silver extraction improved up to 5% (70g/t) for the CELP. The final leach solutions contained lower concentrations of copper, which consequently reduces the effluent treatment costs.

Jan 1, 2014