Search Documents

By Felicia F. Peng

The manganese removal from aqueous solution containing high Mn2+ concentration by adsorption and oxidation was studied using manganese oxide particles as the adsorbent. The operating parameters including pH, flow rate, initial manganese concentrations, and oxidant dosage affect the performance of Mn2+ removal were evaluated in a laboratory packed column. In the multi-column adsorption tests, each additional column doubled the time for complete manganese removal. No further decrease of pH was also observed once it was lowered to pH 4.5 to 5. This finding implied the possibility of complete high manganese removal without further pH adjustment during adsorption. Oxidation of Mn2+ by dissolved oxygen was found to be insignificant for manganese removal for high Mn2+ concentration. Adsorption was the predominated mechanism involved with manganese removal. Extremely low H+/Mn2+ stoichiometry compared to the reported values was measured. These low values suggested that different adsorption mechanisms such as chemisorption other than H+/Mn2+ ion exchange might play an important role at low pH. This paper presents the quantity and explanation of the results obtained for the mechanism of adsorption and oxidation of high concentration manganese on the manganese ore particles.

Jan 1, 1997

By René Winand

A new process was studied at large laboratory scale at Université Libre de Bruxelles, under contract with Metallurgie Hoboken-Overpelt. A two cathodes (1m long ; 0.2 m high) channel cell was used at 2000 A/m2, with an electrolyte flow rate up to 1.8 m/sec. The main results may be summarized as follows : cathodes are electro¬refined grade in analysis ; metallographic structure and surface roughness are kept under control up to 1.3 cm (one side deposits) ; silver in cathode is controlled by CI and Br ions in solution ; organics must be used at very low concentrations (in the range of 0.1 mg/1, with a consumption of about 0.01 mg/lh).

Jan 1, 1987

By R. Winand, P. Harlet

he cathodes produced are of electrorefined grade; metallographic structure and surface roughness are controlled to a depth of 1.3 cm (single-side deposits); silver levels in the cathode are regulated by the presence in solution of Cl- and Br- ions; organics must be used at very low concentrations (around 0.1 mg/l with a consumption of about 0.01 mg/l/hr). The required concentrations of additives were established according to a well-defined strategy based on the consumption of organics at the cathode by a mass transfer limited-process.

Jan 4, 1992

By Veronica Escobar

This paper presents results from a two month pilot evaluation of EMEW® technology at CODELCO Radomiro Tomic, in Chile. A prime focus in the test programme was to assess the technology?s capabilities to recover high quality copper from the Radomiro Tomic electrowinning tank house bleed stream. The EMEW® cell developed by Electrometals Technologies Ltd. tolerates substantially higher levels of contaminants than those found in conventional tankhouse, operating at high current densities while maintaining high cathode copper quality all the way down to low copper concentrations. To maintain high copper purity in a copper electrowinning (or electro-refining) tank house, a continuous bleed of solution must be taken from the tank house inventory to prevent build-up of contaminants, and resulting degradation in cathode quality. In an SX-EW operation, this bleed stream is normally recycled back to the solvent extraction circuit, but is occasionally sent to the raffinate pond to re-enter the leach circuit. Return of the bleed stream to the solvent extraction circuit creates a continually recycling load of copper in solution, which may reduce overall plant capacity and expansion potential. Return to the leach circuit has a similar effect, and methods to reduce its impact are always under consideration. The use of the EMEW® technology allows for direct and efficient recovery of near 100% of the contained copper instead of recycling. Tests were run at ambient temperature on bleed electrolyte using current densities which varied between 250 and 1100 amps per square meter, with copper concentrations between 38 and 1 g/l. A profile of maximum allowable current density with respect to concentration was developed, showing that high grade copper can be obtained at all levels of concentrations tested, by choosing an appropriate current density and electrolyte flow rate. The results of this programme show that the recirculating bleed electrolyte from an SX-EW operation can be converted into an expansion in copper production at a comparatively low investment cost.

Jan 1, 2003

By Gabriel Zarate

"Los Bronces had two ROM dump leach operations designated Leach I and Leach II. Leach I was commissioned in 1998 and stopped in 2014 due to the mine requirements. Leach II plant, commissioned in early 2002, was built to treat around 700 million tons of marginal ROM ore averaging 0.45 % total copper. The mineralogy of this material was estimated to be 70% chalcopyrite, 20% chalcocite/covellite and the balance oxides.The original electrowinning plant design capacity for copper production was nominal 19,500 tonnes per year at a current density of 276 A/m2 and a current efficiency of 92%. Presently, Los Bronces San Francisco plant typically operates at current densities between 390 and 440 A/m2, much higher than the average in the industry, with current efficiencies around 93% and a maximum copper cathodes production of 37,200 tonnes per year.In order to accomplish these achievements, a number of modifications in the process conditions, in the cell hardware and in the operational procedures have been implemented. In the first case, the specific flowrate, copper concentration and temperature of the electrolyte were modified to accommodate the operational requirements facilitating the increased current density. Associated with the cell hardware, a six cells expansion was added, upgraded equipotential inner cell busbars were installed and the cross section of the cathode hanger bars was enlarged for increased current carrying capacity. Documented operational procedures like short circuit detection and cathode weight control were improved.The modifications implemented and the results obtained are discussed in this paper.INTRODUCTIONLos Bronces Division of Anglo American Chile is located up in the Andes Mountains, northeast of Santiago. It had two cathode plants, Los Bronces at an altitude of 3500 meters above sea level (m.a.s.l.) commissioned in 1998 and closed in 2014 and San Francisco at an altitude of 2800 m.a.s.l. and in operation since 2002.The process is leaching run off mine (ROM) low grade copper sulphide ore in dumps. The mineralogy of this material was estimated to be 70% chalcopyrite, 20% chalcocite/covellite and the balance oxides. The average grade is 0.45% total copper (Cut).At Los Bronces dump, Leach I plant, the pregnant leach solution (PLS) was collected and stored in an underground reservoir. From there, it was fed to a solvent extraction plant with a series-parallel configuration in two extraction stages and one stripping stage. The electrolyte produced was fed to the electrowinning plant having 30 cells and 60 cathodes per cell. Maximum capacity of this plant was 12,000 tonnes per year (tpy)."

Jan 1, 2016

By M. Takebayashi, K. Takenaka, S. Matsubara, T. Yoneyama

The cathode production of Toyo Smelter and Refinery, owned by Sumitomo Metal Mining Co., Ltd. reached 450,000 tons per year in 2016 with three tank houses. Niihama tank house commenced operations in 1919 with conventional sheet cathode technology. Approximately 100 years of operation experience and the technical development enabled that the current density of Niihama tank house and the Toyo tank house #1 increased to 320 A/m2. These operation techniques were utilized at the Toyo tank house #2 which started in 2005, and its current density reached up to 350 A/m2 with permanent cathode technology. In order to achieve high current efficiency under condition of 350 A/m2 operation at Toyo tank house #2, continued efforts had been made to verticality of anodes and permanent cathodes. To improve verticality of anodes and cathodes, reduction of short circuit ratio by changing the shape of the anode, optimizing the anode pressing machine and off-line process for rectifying the distortion of permanent cathodes was carried out. In addition, concentration control of electrolyte and expansion of Ni removing ability from the electrolyte prevented passivation. Finally, more than 96% of the current efficiency was stably confirmed. INTRODUCTION Today, Toyo Smelter and Refinery of Sumitomo Metal Mining operates three tank houses in Japan, namely, Toyo tank house #1, Toyo tank house #2, and Niihama tank house with a total capacity of 450,000 metric tons of copper cathodes. Figure 1 shows the trend of cathode copper production and the current density at three tank houses over the last 10 years. Cathode production by Toyo Smelter and Refinery reached 450,000 tons per year in 2016 with three tank houses.

Jan 1, 2019

By C-D. Johansson, B. Ögren, B. M. Ludvigsson, K-Å. Johansson, R. Lindh, G. Berg, M. Maliarik

This paper presents the High Current Density (HCD) Silver Electrorefining Process. A 25-year history of development of the silver electrorefining process as well as associated equipment is given. The process is simple and robust, but at the same time highly automated. With low operating costs and man power requirement it allows consistent production of 99.99 % quality cathode silver. The process ensures that no toxic gases are formed in the working environment. Silver Electrorefining is a heart of a Silver Refinery plant covering the complete range of processes from casting of silver Doré anodes to casting of the bars of refined silver or/and silver granulation. The process has been successfully applied at 11 installations world-wide with plant capacities ranging from 30 to 1500 tpa.

Jan 1, 2014

By M. Mirzazadeh

Air cooled crackable and conventional forged steel specimens were tested under reversed push-pull conditions to examine the effect of shot-peening on their high cycle fatigue behaviour (-106 cycles). The steels were tested in the normalized as well as shot-peened conditions. The results showed that shot-peening smooth specimens had little effect on the fatigue limit of the air cooled forged steels and the detrimental effect of the rougher peened surface was not apparent. Microhardness profiles indicated that the shot peening produced a gradient of compressive residual stresses that was greater than that of the loading stresses, suppressing the anticipated beneficial effect on fatigue life. Crack initiation was more likely to occur below the surface. The results indicate that the surface roughness was not a significant factor in controlling the fatigue lives, since they were essentially the same for the non shot-peened and shot-peened steels.

Jan 1, 2010

By J. Kolacz

A new optical sorting system based on a complex image analysis and high definition imaging has been developed by Comex. The image analysis is based on high definition cameras of different types and advanced filtration tools for verification of waste particles. Different mineral properties are used to identify the processed material. The system is further combined with a high speed rejection mechanism based on FPGA technology and operating in real time conditions. This provides a minimal error when removing waste particles from the sorted material.

Jan 1, 2014

By A. J. C. Paterson

High density slurry and paste tailings systems offer significant environmental benefits primarily related to reduced water consumption. However, these potential advantages need to be evaluated on a project-by-project basis. The successful design of a thickened or paste tailings system requires that the system is designed to accommodate the effect of the high density slurry on pumps, pipelines and the overall system operation. The transport system must be designed as an integrated unit and the interaction of all the components need to be considered. The transport system includes the slurry preparation plant, the pump station and the pipeline. This paper assesses the impact of increasing the slurry density in a platinum tailings system from conventional densities to thickened and paste tailings densities. As slurry density and rheology increase, there is a sharp increase in energy consumption for the additional water savings and this additional cost needs to be considered. A case study shows that there is a considerable benefit in increasing densities to the point at which tailings can be still be deposited in the standard manner. For existing systems, increasing density can result in an increased capacity at a marginal power cost, provided that the slurry is not too viscous. For a new system, a smaller pump and pipeline can result in lower capital costs and a marginally higher energy cost, if the optimum density is selected. Keywords: tailings, paste, pumping, slurry

Jan 1, 2004

By H. Polat, M. Polat, S. Chander

A high shear treatment step was observed to improve flotation of coal. The effect of high shear treatment (HST) was a strong function of coal rank, however. For the low rank coals the HST produced loose, open-structured agglomerates which decreased the entrapment of ash minerals. For the high rank coals, the high shear treatment promoted detachment of low-floating particles from the agglomerates that ordinarily formed in a flotation cell. The extent of agglomeration and detachment of particles from the agglomerates was a function of the amount of dodecane and coal rank. To obtain desired efficiency of separation ethylene-propylene oxide block co-polymers were used. The results showed that the HST-flotation technique increased the ash rejection considerably for both high and low rank coals, though the mechanisms were different.

Jan 1, 1995

By William Kohan

The industrial grinding process has undergone changes to better address the market and economic needs. Fine grinding of dry materials has developed to the point where classifying linings and fine ball charges improve mill efficiencies. Roller mills as well have wide acceptance due to their power efficiencies. The mill, by its nature, cannot provide the specific particle size or range of sizes which are required for further processing or final use. Therefore, various separators are operated in conjunction with the mill to control particle size. The sizing device helps minimize over grinding and control top size. Rising energy costs combined with increasingly tighter quality specifications have led to increasing study of the grinding and separation process.

Jan 1, 1985

By D Morton, G Wallace

"Evolution Mining is the sole owner of the Mt Rawdon open cut operation, located 75 km south-west of Bundaberg in Queensland, Australia (Figure 1). It is a massive, volcanically hosted, low-grade gold deposit that exhibits excellent characteristics conducive to low cost mining and treatment.In 2014, Mt Rawdon began investigating initiatives to deliver higher mill throughputs without any significant capital expenditure or modifications to the existing processing plant. Various studies have shown throughput increases are possible by applying more blast energy, essentially by reducing feed size through blasting and leaving less work for the comminution circuits (Brent et al, 2013; Ziemski, 2011; Workman and Eloranta, 2003).Given that 53 per cent of energy used on a mine site is consumed by the comminution circuit, with only two per cent being consumed by drill and blast (Smith, 2013), it makes logical sense for a mining operation to align their drill and blast with their processing plant. The term commonly used when exploring this relationship is a ‘Mine to Mill’ program.Over nearly 12 months, various blasting options and Mine to Mill methodologies were tested at Mt Rawdon. Throughout the journey, it was abundantly clear that the Mine to Mill initiative is not as simple as making one technical or physical change and expecting an improvement. Rather, true sustainable improvements demand a paradigm shift across both the mining and processing cultures, where all departments are aligned and working towards the one outcome. This true overarching Mine to Mill mentality, enabled by Vistis™ 250 high energy bulk explosive, ultimately led to a sustained increase in throughput and profitability of the Mt Rawdon operation.Citation:Wallace, G and Morton, D, 2016. High Energy Bulk Explosives and Mine to Mill Focus – the Mt Rawdon Story, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 60–69 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Gábor Mucsi, József Faitli, Imre Gombköto, Sanjay Kumar, Zoltán Molnár, Balázs Ráczkevi, Ádám Rácz

"Generally, fly ash particles are very fine (< 100 ?m), mainly spherical and glassy materials form an outer shell on it. This paper deals with the laboratory investigation of ground fly ash based geopolymer. This material can be applied in many fields, mainly in the construction industry, e.g. non-structural elements, concrete, pavements and products, containment and immobilization of toxic, hazardous and radioactive wastes, advanced structural tooling and refractory ceramics, and fire resistant composites used in buildings, etc. The preparation of fly ash using high energy density milling is presented. Systematic experimental series were carried out in order to optimize the preparation process. The particle size distribution (LPSA) and structure of fly ash (FTIR) and the uniaxial compressive strength ,the permeability and structure of geopolymer product, furthermore the rheology of geopolymer paste were investigated. The product properties were studied as a function of the fly ash fineness. As a result of the investigation the relationship between the grinding circumstances, the ground material properties and the geopolymer characteristics was identified. It was found that the above mentioned physical properties of the geopolymer strongly depend on the grinding process."

Jan 1, 2014

By Venkataramana Runkana, Shantanu Maheshwari

As the world reserves of high quality ores are getting depleted at a rate higher than ever, the liberation of valuable minerals from low grade ores is becoming more and more relevant and imperative. But, liberation of minerals from low grade ores requires grinding of ore to extremely fine sizes. High energy milling in a planetary ball mill is one such option where one can produce particles in the nano-meter range. Although planetary mill is employed extensively for ultrafine grinding, dynamics of grinding inside the mill is not fully understood because of the dependency of grinding kinetics on many interconnected phenomena like collisions between media, particles and wall, time dependent rheology, adsorption and desorption of dispersant, abrasion of media, agglomeration of particles, etc. It was well articulated in literature that media motion and number of media collisions have strong effect on grinding kinetics and final product size distribution. Simulations were carried out using the discrete element method (DEM) to compare the performance of a planetary mill with a ball mill, with and without lifters, in terms of impact energy and number of collisions and it was found that number of collisions is considerably high in the planetary mill. The high number of collisions might be the reason for production of ultrafine particles in the planetary mill. We have also fitted a population balance model (PBM) to experimental data from a laboratory scale planetary mill for prediction of particle size distribution. Unlike previous models, we have incorporated functional forms for the selection function and the breakage distribution function so that the number of parameters in the PBM is just five. The predicted product particle size distributions at different grinding times are in reasonably good agreement with experimental data.

Jan 1, 2014

By A. Grimod

The European Guideline ETAG 027 - 2008 (?Guideline for European Technical Approval of Falling Rock Protection Kits?) defines the procedures to test rock fall barriers. Nowadays, this guideline is essentially the only test and construction framework utilized by manufacturers and it is also starting to enter in the mentality of designer who can clearly specify the performances of rockfall barriers. ETAG 27 (and the related European Technical Approval and the CE marking) represents a milestone for the rockfall barrier market, because it gives the possibility to compare the performances of different fences and it ensures the quality of the certified product. For these reasons ETAG 27 presently constitutes the base for tenders all around the world. Although rockfall barriers are in common use, designers and consultants do not have a clear overview of the real performances and the technological limits of these structures. The first problem can be solved using ETAG 27 criteria, which allow designing rockfall barriers at ultimate and serviceability limit state. Even though ETAG 27 uses crash tests performed with the Service Energy Level (SEL) and Maximum Energy Level (MEL), design with these concepts is not obvious or in common acceptance. Some preliminary questions must be solved. When can these energy levels be correctly applied? In the case of rockfall simulations, what probabilistic approach must be used for the evaluation of the barrier? Unfortunately ETAG 27 does not give any information or tests relating to the technological limits of the fences. Therefore some important questions arise. How do the site specific aspects of installation affect the barrier performance? What is the behaviour of the barriers under extreme conditions? And finally, the main question lies in the background: what is the functional reliability of ETAG 27? All of the above questions require comprehensive answers, which is consistent with the experience of designers, installers and producers. Officine Maccaferri S.p.A., with its 130 year experience in the field of rockfall protection, collected a large number of case histories with barriers impacted by single or multiple blocks, debris flows, and snow avalanches. Throughout these case histories and in accordance with a recent Italian standard code, it has been possible to implement a reasonable design approach that considers the efficiency of the barrier, the uncertainties of the input data, and the fore

Aug 1, 2013

By J. Iannicelli

An entirely new level of magnetic filtration technology was put into full commercial production by the kaolin industry of Georgia, U.S.A. during 1973-1974. At present, four kaolin producers in Georgia are operating large magnetic filters each capable of processing over 1000 gallons of kaolin slurry per minute or over 65 tons of kaolin per hour on a dry basis. A fifth large filter will go on stream in August, 1975. Four of these units are 84" machines manufactured by the Pacific Electric Motor Company of Oakland, California. When operated at the maximum 1000 g, p. m. rate, these five large magnetic filters have a combined capacity approximating the entire waterwashed coating and filler kaolin produced in the U.S.

Jan 1, 1976

By John A. Herbst, Alexander Potapov, Xiangjun Qiu

"High Fidelity Simulation is a name applied to the use of first principles modeling tools including Discrete Element Modeling (DEM), Computational Fluid Dynamics (CFD) and Discrete Grain Breakage (DGB) to mathematically describe and study processing systems. Over the past few years, significant advances have been made in High Fidelity Simulation applications, particularly as many mineral processors have been drawn to the study and use of DEM of grinding mills for optimization purposes. This presentation provides an introduction to High Fidelity Simulation, with an emphasis on DEM. It will include insights into current applications of these tools including the optimal design (wear and throughput) of mill lining systems and media selection, the analysis and design (flow and efficiency) of the back-end of grate discharge mills. Advantages of full mill simulations versus individual sub-process simulations will be demonstrated for a SAG mill with different discharge system designs.INTRODUCTIONHigh Fidelity Simulation is providing mineral processors with the opportunity to analyze the behavior of mineral processing equipment from a fundamental or microscale point of view. In the past complex phenomena such as tumbling mill grinding had to be analyzed using black box tools such as residence time distributions for transport and classification functions for passage of particles through grates; while breakage had to be analyzed using PBM models who derived their form from theory but required direct measurement of kinetics. Today with the help of DEM, CFD and DGB these can be analyzed at a very fundamental level.The key element of DEM simulation is the application of Newton’s laws of motion to individual objects or discrete elements. Using this simulation method one can describe the position, velocity (both translational and rotational) of all objects and the transfer of momentum to other objects (Mishra and Rajamani, 1992; Cleary, 1998; Nordell et al, 2001)."

Jan 1, 2003

By J. A. Herbst

Mineral liberation modeling can be traced back to the early work 0fA.M. Gaudin up through more recent population balance modeling by R.p. King, J.A. Herbst and G.T. Adel. A more micro-scopic look was taken at the University of Utah in the form of the J.E. Sepulveda and J.D. Miller Pargen model which permits the creation of an arbitrary shape, multiphase particle made up of discrete grains. Recent work on image analysis and tomographic analysis by J.D. Miller and C.L. Lin have laid the experimental ground work for model validation, but until now it hasn&apos;t been possible to include the necessary physics of the particle stressing process to allow the development of a &apos;ffirstprinciples"mode1 which does not presuppose a "mode” of liberation (e.g., random or by detachment). Recent developments in discrete grain breakage (DGB) modeling now make a generalized physics based model feasible. This paper describes current work that is being done to develop a physics based discrete grain liberation (DGL) model. Two-dimensional and three dimensional simulation results exploring the effects of particle size, phase properties and loading type are presented. Relationships between energy based liberation efficiency, degree of random liberation and material properties are identified.

Jan 1, 2005

By Lucas Nana Wiredu Damoah, Lifeng Zhang

"The use of electromagnetic field to remove suspended particles from metals such as aluminum by pushing to the boundary has been well studied. However, the potential of this method is yet to be exploited for the removal of inclusions from silicon. Considering the increasing amount of Top-cut SoG-Si scraps year upon year, there is the need to harness all the potentials of technologies to recycle this materials to ensure sustainability. This study investigates, and discusses new results on the effect of processing parameters such as composition, coil current, and frequency on the removal of inclusions from silicon under high frequency AC electromagnetic field.IntroductionThe solar cell silicon making industry requires pure and clean silicon in order to maximize the conversion potential of the solar cell material. The conversion efficiency of solar cells is limited by minority carrier recombination at dislocations and those intra-granular defects such as impurities, small clusters of atoms, or precipitates [1]. Recent global developments in the energy sector with a drive for the production of clean, reliable, and affordable energy have stirred a rapid growth in the production of photovoltaic (PV) cells.[2] Thus over the years, silicon based PV cells has seen a lot of growth as it has a PV market share of over 90 % [3] either as single-crystalline silicon, or multi-crystalline Si (MC-Si), or amorphous Si [4]. MC-Si produced by directional solidification of solar grade silicon melt dominates the silicon PV market. During the directional solidification process, SiC and Si3N4 particles within the melt are pushed by the solidification front to the top of the ingot which is the last to solidify. Therefore the top of the ingot is cut generating what is known as top-cut solar silicon scraps. The Si3N4 particles are mainly from the coating material at the inside surface of the silica crucible and from the air absorption during solidification process. The SiC particles mainly stem from the carbon reduction process of the primary production of silicon [5]. For sustainability the silicon in the top-cut silicon scraps must be recovered. Therefore methods for removing non-metallic particles, such as SiC and Si3N4, from the silicon are important in order to recycle the top-cut scraps to a useful feedstock for the silicon solar cells manufacturing."

Jan 1, 2012