Search Documents

By R. K. Mehta, M. G. Bersch

Characterization of an ore or mill product is routinely performed by time consuming and tedious chemical analyses, sink-float separations, etc. Additionally, these types of tests do not provide data concerning the interrelations and interlocking of the mineral constituents. This paper discusses some of the applications and capabilities of the Minerals and Material Science Research Center at The University of Alabama. Back-scattered electron images of coal, oil shale, complex suldfide, and tantalium ores were acquired using a JEOL 8600 electron microprobe with a NORAN (formerly Tracor Northern] 8500 image analysis system. Methods of analysis and typical results are discussed.

Jan 1, 1992

By G D. Matthews, M E. Haylett, S Khosrowshahi, A Weeks

In narrow orebodies the use of ordinary kriging (OK) may pose certain limitations when used for grade control modelling. The smoothing effect of kriging, by its very nature, cannot retain or accurately characterise the dispersion (variability) that is inherent in gold deposits. This dispersion is a critical component of determining the desired level of ore loss and dilution.Fixed block model positions used in OK, and all estimation approaches, within a grade control process may never align with the ‘true’ ore boundary. This may lead to excessive ore loss and dilution, especially within narrow lodes.Using a risk-based approach to ore block design based on the geostatistical method of conditional simulation (CS) can highlight the differences achieved when an alternative method to OK is used for grade control modelling. By using a mesh of nodes and the application of a ‘transfer function’ to the simulation models, the position for ore contacts can be better assessed than when using fixed blocks in OK. Therefore, the value of various ore block boundaries can be better analysed by objective assessment of ore loss and dilution for a given minimum mining selectivity (selective mining unit or SMU), even in narrow lodes.A case study of a narrow vein gold deposit, comparing the results from an OK model and a CS model shows that whilst both models show similar trends – waste, low-grade, and high-grade regions are the same in both cases – the simulation model can provide greater insight for optimal definition of the mineralisation boundary.CITATION:Haylett, M E, Weeks, A, Matthews, G D and Khosrowshahi, S, 2014. Ore block design in narrow vein gold deposits – estimate or simulate?, in Proceedings Ninth International Mining Geology Conference 2014 , pp 421–424 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Hall C. E, Chrisholm J. M

Resource calculations for shear hosted deposits of any type are difficult regardless of which calculation technique is used. One of the main problems is the determination of the geometry of the mineralisation. Once this has been elucidated then the appropriate resource calculation methodology can be employed with a search distance and orientation that is relevant.

Jan 1, 1993

By M B. McKevitt, W J. Shaw

The main task of grade control on a daily basis is to define the material that should be mined to a destination under various categories. This can be determined by grade, lithology, quality and blending criteria. In the case of multi-element deposits or deposits with various blending or other processing criteria the optimum selection of ore block boundaries can be quite complex. In every case the balance between ore loss and dilution must be considered when designing the ore block boundaries and this becomes a risk-based decision when using the conditional simulation model. The use of such systems allows grade control to meet specific targets, such as budget tonnages and grades and blended product specifications. Two case studies are presented: the Prominent Hill copper/gold mine and the Rapu Rapu zinc/copper mine. Mining is based on a rational grade control strategy involving a number of factors, including strong geological control, advanced geostatistical approaches, such as conditional simulation, and optimisation of the ore blocking to meet production requirements. This provides an objective, transparent and repeatable grade control strategy.

Jan 1, 2009

The impact of smoothing on the definition of ore and waste boundaries using linear estimation and conditional simulation methods is discussed. The nature of transfer functions is examined including their ability to incorporate categorical data (e.g. a dominant lithology code). An Ore Block Optimization (OBO) transfer function is presented that provides a clear guide for the mining geologist. Advantages are seen in defining stockpile cut-off grades and meeting production targets such as maximizing head grade, maximizing ore tonnes or minimizing ore loss or dilution. Each of these scenarios impacts on mine profitability and grade control.

Jan 1, 1999

By R. Sandefur

Recent advances in personal computer technology allow movies of various types to be made and displayed on PC and Macintosh computers. An interesting application of this movie technology is animation of computerized geological models. These movies, which can be most easily constructed along rows, columns, and benches of block models, allow an ore body to be more easily and quickly visualized than the traditional method of flipping back and forth through various sections.

Jan 1, 1994

By Bruce Kennedy, Charles Bruce

MINERAL EXPLORATION 'The Function of Exploration Mineral exploration aims at locating the presence of economic deposits and establishing their nature, shape, and grade. As all ore bodies are finite, exploration is essentially the lifeblood of the mining industry. It is divided into two phases, reconnaissance and target investigation. It involves geological mapping, geophysical prospecting (aerial and ground or both), geochemical surveys, prospect drilling, and/or exploratory under-ground workings. Successful exploration is followed by development drilling, mine development, and eventually operation. In underground mining, the term "ore" is applied rather loosely to metalliferous rock that can be profit- ably mined, but nonmetallic industrial minerals and energy related materials constitute a large and growing portion of the tonnage extracted by underground methods each year. It is appropriate, therefore, to consider exploration as the search for any useful substance occurring in the earth or in the oceans that is of sufficient value as to volume, grade, chemical and physical com- position, and location as to make extraction by mining commercially profitable for the investment required. The Selection Process The search for ore includes hundreds of mineral commodities. The more successful exploration organizations tend to restrict the search to the mineral commodities for which they have strong exploration expertise and which have a high probability of being concentrated in areas open to exploration and development in sufficient volume, grade, and proximity to the surface to warrant the large expenditures of risk capital in finding an ore body. Special expertise is needed to engage in mineral exploration and development for the extended periods required for success. Individual prospectors continue to discover mineral occurrences, but it generally takes an organization with strong financial resources to carry the exploration process forward to the point of developing "ore." Still greater corporate resources in the form of management, engineering, and sales capability are needed to develop an ore body into an operating mine. In the past, companies other than those engaged in mining rarely conducted exploration, since they lacked the technical skills and know-how to bring a mine to fruition. A notable trend in recent years has been the success of other resource-oriented firms, such as petroleum companies, that have not only acquired the necessary skills to engage in exploration for hard minerals, but are doing so on a far more intensive scale than known in the industry heretofore. The desire to diversify from increasingly regulated oil and gas, the potential for the discovery of a bonanza, and the large scale of mining projects for these capital-intensive firms are the attractions. US government and certain international organizations, such as the United Nations, have fielded sizable exploration programs in the past decade on behalf of Third World countries wherein many of the world's higher grade deposits and scarce mineral resources are located. The level of overall mineral exploration in the industry is, regrettably, closely geared to the business cycle. Accelerated search during the periods of strong demand, shortages, and high prices, together with the long lead times necessary to develop mineral finds, often creates surges in supply which invariably are followed by a collapse in prices. The trend is, therefore, to exploration funding by larger better-endowed firms having the staying power to weather the cyclical nature of mining. Tax incentives, tariff policies, and other incentives have a decided impact on the level and nature of exploration. Surface mining regulations and environmental forces have fostered a renewed interest in under- ground development despite the lower average costs of surface mining. Spiraling inflation has caused mining costs to outpace prices for many mineral substances. Organizations increasingly are directing their search away from high- grade but limited tonnage occurrences toward low-grade disseminated bulk tonnages amenable to mining on a vast scale. Mining continues, therefore, to grow even more capital-intensive with half-billion-dollar mine-mill- smelter complexes now commonplace, compared with the hundred-million-dollar projects of a decade ago. Reconnaissance Exploration Having elected to search for specific mineral commodities, the exploration company narrows its focus to a reconnaissance of those regions offering the best potential. A working hypothesis which is constantly up- dated concerning the geologic controls for ore occurrence guides the search. The possibilities for discovery are best in areas of existing mines and known ore bodies, where the probabilities are high for additional ore occurrences. In such areas, published data on the trends and geologic controls of known mineral occurrences aid the search. Even in some remote territories, a variety of geologic data is available to the explorationist. The major sources of basic geologic data are the libraries of the US Geological Survey (USGS), the state geological surveys, the American Institute of Mining, Metallurgical, and Petroleum Engineers (AIME), the US Bureau of Mines, and various institutions such as Colorado School of Mines. Overseas, virtually all of the countries have their own geologic survey groups which are associated directly, or indirectly, with their respective ministries of mines. The objective of reconnaissance exploration is to narrow the search by pinpointing target areas having interesting mineralization. These favorable areas are then investigated in detail to delineate potential ore bodies.

Jan 1, 1982

By D. J. Lachel, Douglas E. Hansen, Bruce Kennedy

The very high cost of exploration and development for new mines requires that a carefully planned, complete, and technically competent geotechnical evaluation be applied to the ore body and the surrounding rock. The ground conditions must be predetermined sufficiently so that, during the development and exploitation stages, unexpected conditions will be of minor consequence. Ground conditions are a major factor affecting the cost of excavated items such as shafts and inclines. For example, shafts cost less to sink in tight dry ground than in highly pervious ground below the water table, with all other factors being equal. The proper mining methods also is dependent upon the ground conditions. Bad ground for room-and-pillar mining may be ideal for caving methods; whereas, ideal ground for room-and-pillar mining would be extremely difficult for a caving operation. To do a proper engineering design, the parameters of strength, deformability, and permeability must be determined, in addition to the loads that will be applied as a result of the mining activity. The required degree of accuracy for each parameter depends upon the individual case. For example, the strength of massive rock in which openings of small cross-sectional area are to be driven at shallow depths needs to be resolved only within several thousand kilopascals (pounds per square inch). Under such conditions, the rock strength is not likely to be of great economic importance unless the rock is very weak. Large openings at great depths require a much more accurate appraisal of rock strength and deformation characteristics. Ground water conditions are important at any depth. Today, a number of techniques exist for evaluating conditions before opening up the ground for development. These techniques and their applications are described in more detail later in this text. The evaluation of ore body ground conditions should start at an early stage, as soon as the deposit has been proven viable for a mine. Economic geology investigations mainly serve to define the value and limits of the ore deposit. To do this properly, the geology of the site is determined in at least as much detail as is necessary to define the "controls" for the ore body. The ground-condition evaluation must determine the engineering properties of the ore body and the surrounding material. This includes the structural geology as it relates to rock strength; i.e., the frequency, extent, and orientation of discontinuities such as faults, joints, bedding, etc. Ground water conditions also must be determined. It is important that the detailed geology of the site be determined at an early date. Reasonable geotechnical parameters must be established during this time period, so they can be used in mining model studies that include both physical and mathematical models. The ultimate goal bf-the geotechnical evaluation is to predict the ground behavior as the excavations are made and how the ground behavior will affect the safety and economic well-being of the mine. The formulation of a ground-condition evaluation program should be planned carefully to determine the particular geotechnical parameters only in as great a detail as will have a bearing on the mine design. For instance, it is not necessary to make numerous triaxial tests in strong rock when the mining will be conducted within a few meters (feet) of the surface in a regime of gravity loading and an absence of tectonic stresses. Similarly, it is not necessary to invest large amounts of time and effort in the determination of joint strengths if the orientations of the joints are such that the failure could not occur along them. Generally, the determination of ore body ground conditions can be divided into four main steps: 1) The general and structural geology of the site must be determined; this is determined primarily during the economic evaluation. 2) The material behavior characteristics of the deposit and the vicinity must be determined. 3) The ground water hydrology of the deposit and the vicinity must be determined. 4) Miscellaneous ground support considerations must be established. Gross features are defined first, followed by a series of increasingly detailed investigations. Specifically, the geology study should start by utilizing techniques such as remote sensing, topographic map interpretation, geologic mapping, etc. After the gross features, such as major faults, have been delineated, the studies are directed toward defining the more detailed elements of jointing, rock strength, ground water hydrology, and other characteristics. This information is used to formulate an assessment of the strength of the ore body and the surrounding rock. Finally, all of the gathered information is integrated to make an assessment of the rock behavior in relation to the types of openings, the excavation methods, the support requirements, etc., that should be used for the rock conditions that are present. The mine design and the geotechnical assessment should be an iterative process. General conclusions about the rock conditions will dictate a type of mine plan. The specific mine plan then should be modified by specific geotechnical considerations. For example, an initial assessment may conclude that the ore body is strong and that a strong rock unit is present over the ore body. Thus, one definite possibility is to mine the deposit by room-and-pillar methods. However, subsequent investigations may reveal faults through the deposit, requiring relocation of the mine openings so that pillars and other structures are in sound rock. In other words, the final mine plan should be compatible with the geotechnical aspects of the ore body.

Jan 1, 1982

Parallel lenticular orebodies occurring at the C.S.A. mine of Cobar Mines Pty. Ltd. are mined by mechanized cut and fill stoping over the full strike length. Access is provided for each stope lift from an inclined drive adjacent to the orebody. Mobile drill jumbos mounting hydraulically-operated booms are used for drilling upholes which are subsequently charged with ANFO explosive.Close control of drilling has been found essential for good back conditions and to ensure optimum fragmentation.Broken ore is transported from the face to the main ore pass by rubber-tyred, diesel-powered, load-haul-dump units. Initially, the units trammed ore to the main pass via the incline drive. As the stopes advanced and the lead distances increased, stope passes were developed in the wall rock and raised concurrently with each stoping lift. The passes terminate in drawpoints and production loaders are used to transport ore from the drawpoints to the main ore pass system.Two parallel ore pass systems have been developed to cater for both copper and copper-zinc ores. These systems terminate above a 48 in. by 60 in. jaw crusher. The crushed ore is conveyed to a traversing rock box and thence to one of two crushed ore bins adjacent to the main hoisting shaft. A loading station conveyor is interlocked with the winder to provide automatic ore hoisting.All phases of ore handling have been mechanized as completely as possible. Results to date indicate this policy has been vindicated but highlight the need for tight operating control and close liaison between operating and maintenance personnel.

Jan 1, 1969

By Misra V. N

Davis tube tests were conducted on a Koolanooka magnetite iron ore sample, supplied by Kingstream Steel Ltd, to determine the optimum grind size, maximum iron recovery and the cleanness of the products from low intensity magnetic separation (LIMS). The ore sample contained 38.6 per cent iron, 37.8 per cent silica, 6.5 per cent magnesia and 0.54 per cent alumina. XRD and microscopic examination showed that the main minerals in the ore were amphibole (42 per cent), magnetite (39 per cent), and quartz (14 per cent). Amphibole, (Mg, Ca, Fe),Si8O22.2(OH), containing 50.3 per cent SiO2, 35 per cent FeO and 11.5 per cent MgO is the main gangue mineral in the ore, and about 30 per cent of the total iron in the ore is contained in the amphibole. Heavy liquid separation tests showed that it is very difficult to separate iron from silica by gravity separation to obtain a high quality iron concentrate. Three grind sizes were initially tested, ie 45, 38 and 20 ¦m. It was found that grinding to 100 per cent -38 ¦m (P80 of 29 ¦m) appeared to be the best option for liberating the magnetite from gangue minerals. The iron recovery to the LIMS magnetic product for the 100 per cent -38 ¦m sample reached 73 per cent and the iron content was 65 per cent. Further test work suggested that the optimum grind size was a Psu of 25 ¦m.

Jan 1, 1999

By A Scott, S Kanchibotla, J Segui

The æMine to MillÆ concept is not new. In fact, it is the underlying objective of every mine. Unfortunately, in many operations the management structure and reporting systems have created independent æbusinessesÆ within the overall mining enterprise. This has created incentives to optimise the performance of each component of the operation rather than the enterprise as a whole. The Mine to Mill Conference organised by The AusIMM in October 1998 documented a number of case studies where run of mine ore was not presented to the mill in the best possible form for subsequent stages of comminution and processing. A number of examples were quoted where modest expenditure in the mine had a very significant impact on downstream process efficiency and hence costs. Examples included:the minimisation of fines in the mining and handling of iron ore; the management of fines in blasting and crushing for a copper heap leach operation; the control of blast damage, mining recovery and dilution in open cut coal operations; and the optimisation of mine fragmentation to increase mill throughput in gold and copper operations. The latter topic has been trialed at a number of mines and is referred to as æMine to MillÆ fragmentation. A number of æMine to MillÆ type investigations have been reported in the literature including Pease et al, Simkus and Dance, Nielsen, Scott et al, Kojovic et al, Kanchibotla et al, Bulow et al and Hawkes from the 1998 Mine to Mill Conference. In addition, a number of studies are in progress or the results have yet to be published. These studies have demonstrated the feasibility of obtaining the data required to characterise the breakage behaviour of ores and to model the impact of changes to blasting practices on process efficiency. Characterising the breakage behaviour of ores is a vital step in the management of fragmentation and comminution in mines. The characteristics of importance to fragmentation fall outside the parameters conventionally required to describe the economic geology of a deposit. æMine to MillÆ optimisation of fragmentation means that the mining engineer needs information from the geologist in order to be able to help the metallurgist. Providing this information requires close interaction between these groups.

Jan 1, 2000

By Steven W. Wilson, Brigitte Lacouture, Nichola A. McKay

"The Aqqaluk deposit is a lead-zinc ore body that lies immediately north of the Main Pit at Teck Cominco’s Red Dog Mine in Alaska. It is scheduled to begin production in 2011 or 2012. A project team was formed in late 2004 to plan and implement an ore characterisation and metallurgical evaluation on the Aqqaluk ore. The main objective of this program was to facilitate the transition from Main Pit to Aqqaluk ore in the Red Dog concentrator. The program will develop a detailed, spatially-oriented characterisation of the Aqqaluk deposit attributes including lithology, ore geochemistry, bulk mineralogy, ore texture, as well as evaluating the metallurgical characteristics of ore hardness, process water geochemistry, bench-scale floatability and mineral liberation in ground feed, concentrate and tails. Developing correlations between the metallurgical response and the ore characterisation data is key to the emerging science of geometallurgy. This on-going program is a technical due diligence study that aims to reduce the risk associated with processing a new ore and to provide predictive information for mining and stockpile preparation.The test work to date has focused on characterising the five ore zones currently identified in the Aqqaluk deposit, namely: Siliceous (sub-divided to High Zn:Fe and Low Zn:Fe), Vein, Median Plate and Baritic ores. It identified a number of challenges associated with surface oxidation, or weathering, of the core samples and outlined a program for future sample collection and storage. Metallurgical testing evaluated ore hardness by a variety of methods. Preliminary floatability studies have been completed and some initial links have been established between the ore characteristics and the flotation response. Soluble mineral weathering products, the relative abundance of pyrite and marcasite and the iron content in the sphalerite grains have all shown a correlation to mineral recovery.As new core is received, both the ore characterisation and the metallurgical testing will be continued with a view to strengthen the existing correlations and develop new links."

Jan 1, 2007

By W. Petruk

A study was undertaken to determine whether interrelations between mineral grains affect ore breakage during grinding, and to establish a correlation between ore breakage and mineral liberation. A base metal ore from the Brunswick No. 12 deposit in New Brunswick was ground for different periods of time in a laboratory ball mill, and both the unbroken ore and the ground products were analysed by image analysis. The results show that the mode of breakage is strongly influenced by the behaviour of pyrite. Similar size distributions were obtained for material from the 15 minute grind in a laboratory ball mill, for the grinding circuit discharge from a commercial mill, and for pyrite grains in the unbroken ore. This similarity indicates that a 15 minute grind breaks poorly bonded pyrite grains along grain boundaries, and represents the limit of easy breakage for the ore. Such a grind liberates both large separate grains of ore minerals and poorly bonded mineral grains that occur in interstices among pyrite. On the other hand the 15 minute grind does not separate moderately bonded mineral grains nor release moderately bonded interstitial minerals from pyrite; a 45 minute grind in a laboratory ball mill is required. It is assumed that, for Brunswick No. 12 ore, a 45 minute grind in a laboratory ball mill is equivalent to regrinding in a commercial mill. Grinding beyond 45 minutes in a laboratory ball mill breaks the ore by fracturing pyrite across grain boundaries and by chipping grain edges. Such intense grinding does not markedly increase sphalerite liberation from Brunswick No. 12 ore, because most of the sphalerite that can be released was liberated at the 45 minute grind. In contrast the intense grinding increases galena liberation because a significant proportion of the galena occurs as minute inclusions in pyrite. These findings show that ore breakage and coincident liberation depend upon size distributions, intergrowths, and mode of occurrence of the minerals in an ore.

Jan 1, 1988

By W. Petruk

A study was performed to determine whether mineral textures affect are breakage during grinding, and to establish a correlation between are breakage and mineral liberation. A base metal are from the Brunswick No. 12 deposit in New Brunswick, Canada was ground for different periods of time in a laboratory ball mill, and both the unbroken are and the ground products were studied by image analysis. Similar size distributions were obtained for material from the 15-minute grind in a laboratory ball mill (K. 0 67 pm), for the grinding circuit discharge from a commercial mill (K. 0 = 59-72 pm), and for pyrite grains in unbroken are (K,. = 74 pm). This similarity indicates that the 1S-minute grind separated weakly adhering pyrite grains along grain boundaries, and represents the limit of easy breakage for the are. At this grind (15 minutes) large discrete are mineral grains and weakly adhering interstitial fillings aIrong pyrite were liberated. On the other hand, the 15-minute grind neither separated rooderately bonded pyrite grains nor released rooderate1y bonded interstitial minerals from pyritei a 45-minute grind (K.. 31 pm) in a laboratory ball mill was required. For Brunswick No. 12 are, a 45-minute grind in a laboratory ball mill (Keo = 31 pm) is equivalent to regrinding in a commercial mill (K ?? Fl:$ 30 pm). Grinding beyond 45 minutes in the laboratory ball mill broke the are by fracturing pyrite across grain boundaries and by Chipping grain edges. Such intense grinding (longer than 45 minutes) did not markedly increase sphalerite liberation. In contrast, the intense grinding increased galena liberation because a significant proportion of the galena occurs as minute inclusions in pyrite. These findings show that ore breakage and coincident liberation depend upon size distributions, intergrowths, and mode of occurrence of the minerals in an ore.

Jan 1, 1988

The use of QemSCAN in providing mineralogical input to detailed ore and product characterization has proved of immense value in recent years. In this paper, a brief review of selected Cu-case studies is presented to demonstrate the versatility of automated, quantitative mineralogy by QemSCAN. This versatility ranges from measurement and analysis strategies through to data processing and presentation. As a rapid diagnostic service, it is common to find that only grain size, the degrees of liberation and/or ore mineral modal mineralogy are of interest. By contrast, the detail afforded by the simultaneous determination of both gangue and ore minerals can alert mineral engineers to fatal flaws and attributes deleterious to processing that are directly a function of silicate and other gangue mineralogy. Examples of the latter effects include the influence of micaceous minerals and acid consuming species, while the former include fluorine minerals, which can provide both processing and environmental challenges.

Jan 1, 2007

By Richard Gertsch, Jack Eloranta, Leslie Gertsch

An ongoing research program is characterizing the ore qualities that most affect mine and mill processing of iron. Current practice uses assays of magnetic iron and silica, but additional qualities are needed for advanced process control. If additional qualities can be measured from core, blastholes, or process samples, they can be modeled and controlled similarly. What qualities, other than assays, hinder or facilitate beneficiation at each processing step, and how can they be measured in the mine/mill ore stream? This paper describes preliminary determinations of the effects of ore chemistry, hardness, blasthole drill performance, fragmentation control, and grindability on mill performance.

Jan 1, 2005

By M. Holuzko, Y. R. Zhang, J. Alexander

The use of dual-energy X-ray transmission (DE-XRT) technology in the mining industry has been developing rapidly in the past decade. In many projects, DE-XRT images are analysed to classify ore and waste in sulphide deposits where the sulphides and non-sulphides have distinct characteristics in density. In the current practice of DE-XRT image processing, every pixel in the image gets classified into two categories, depending on the intensity of the pixel from both low and high energy X-ray response. If the pixel’s intensity is above the threshold curve generated in the high-energy and lowenergy scatter plot, it is classified as “higher density” material, and the remaining pixels are classified as “lower density” material. This paper elaborates on an alternative approach to DE-XRT image processing for in-depth characterisation of samples from a lead-zinc sulphide deposit. The detailed characterisation is achieved by providing density distribution of individual rock using DE-XRT laboratory sorting unit (COMEX) located at the University of British Columbia. Instead of classifying the X-ray images into two different classes from one threshold curve, multiple density classes are created between two threshold curves to generate the density distribution. By manipulating the two threshold curves, we can analyse images of samples obtained at different resolutions of density distribution. If the two threshold curves become infinitely close to each other, it will create a single-threshold scenario similar to the current methods being used in the industry. This method provides the ability to change the threshold curves, hence providing more flexibility on material characterisation based on the needs of the operation. Furthermore, the DE-XRT images from individual rock specimens are compared to the test results from hand-held X-ray fluorescence (XRF) analyser as well as assays of various elements for the same set of samples. The data analysis will provide information regarding ore characteristics and also the theoretical performance of the sensor-based sorting. Keywords: Dual-energy X-ray Transmission (DE-XRT), X-ray fluorescence (XRF), ore characterisation, density distribution

Jan 1, 2020

By D. Allen

Faced with decreasing ore grades and harder ores, many mines today are forced to become more efficient with their approach to processing. Variability in ore hardness, mineral liberation, reagent consumption, sliming, and leach responses are all a function of the minerals present and their concentration. Modern semi-automated X-ray Diffraction (XRD) analyses using Rietveld refinement techniques, in conjunction with high speed quantitative Near Infrared (NIR) analyses, provide reliable quantitative mineralogical ore profiling. By the implementation of XRD with NIR, mining, milling and leaching operations no longer need to be dependant on visual estimates for GeoMetallurgical Modeling and are provided with a valuable forecasting and production control tool. This paper will illustrate the development, plant implementation and application of XRD and NIR at several copper operations.

Jan 1, 2007

By P. A. Roberts

A proposal for a modified in situ leaching method for extracting gold from oxidized gold ores using a non-cyanide lixiviant is described. A non-cyanide lixiviant is suggested because of the obvious concerns posed by injecting cyanide-bearing solutions into the subsurface. Oxidized gold ores were chosen as a focus because earlier research on the use of sodium thiosulfate as a lixiviant under anaerobic conditions indicated that the presence of pyrite led to rapid thiosulfate breakdown. A reconnaissance research program involving ore characterization and hydrometallurgical test work on samples from four Australian ore deposits and preliminary reactive transport modeling studies was carried out. This work showed that lixiviant-oxidant combinations of sodium thiosulfate and ferric EDTA and iodide and iodine are both capable of extracting high percentages of accessible gold from the selected samples in bottle roll tests under anaerobic conditions. The ore characterization and reactive transport studies suggested that both physical and chemical methods of permeability enhancement may be required to lift bulk permeability and the availability of gold for dissolution to sufficiently high levels to obtain adequate gold recoveries. Assuming that such methods prove to be both necessary and economically viable, the mining method would no longer be regarded as simple in situ leaching. Therefore, the term ?in-place leaching? has been adopted for the proposed gold extraction system.

Jan 1, 2010

By E. H. Rose

IN the realm of ore dressing the most pregnant feat of all time was announced in 1945: the winning of the mineral raw materials which made the harnessing of atomic energy possible. Lost in the stupendous implications of the end result, in the two billion dollar hugeness of the project, and in the famous names attached thereto, the fact that crude uranium ores had to be concentrated received relatively little notice in the press. Only the final link in the concentrating chain was publicized-ether extraction of uranyl nitrate, developed by Hoffman and carried on by the Mallinckrodt Chemical Works, or methods developed by the Ames group under Spedding. Some of the earlier links represented less glamorous but equally difficult and exacting research. One may only speak a word of admiration for those who worked hard, accomplished much, and said nothing. The universal lament for most of the year was "man shortage." A group of Canadian engineers expressed it as "being so short of labor that no labor was available to develop laborsaving devices." . Despite this, an outstanding amount of mineral-dressing progress was made in 1945. Necessity allowed no alternative. The insatiable demand of war for minerals forced the exploitation of lower and lower grade ores, and of others not before considered of commercial character or use, requiring the mineral dresser to fight for and win new bridgeheads on the home front.

Jan 1, 1946