Search Documents

Modern coal cleaning technologies have allowed coal preparation facilities to become quite efficient at removing sulfur compounds, waste rock and low grade coals from run of mine coal. Up to 50% of the raw mined coal stream may end up as refuse, particularly when the coal originates from longwall mining operations, or is high in partings, rock and impurities. The refuse materials vary from coarse materials removed by physical screening to very fine materials removed by floatation and density separation processes. Coal refuse piles are also known by a variety of other names including "waste dumps", "gob piles" and "slate dumps". The potential hazards of improperly reclaimed refuse include contamination of surface and groundwaters by acidic leachates and runoff, erosion and sedimentation into nearby watersheds, spontaneous combustion, disturbance of topsoil borrow areas, and damage from landslides should large slope failures occur. Many of these problems have been particularly acute for abandoned refuse piles, and modern regulations attempt to minimize the environmental impact of coal refuse disposal operations.

Jan 1, 1993

By K. Burke, K. L. Myers, R. Espell

Barrick's Goldstrike AA heap leach pad is an HDPE-lined facility that was used for gold recovery from low-grade ores using conventional cyanide heap-leach technology. The pad was operated from 1987 through 1999. Goldstrike prepared a unique reclamation plan for the AA leach pad facility to provide for a cost-effective, environmentally sound facility closure and to fulfill the State of Nevada's closure requirements. The traditional Nevada leach pad closure procedure involves rinsing to reduce the cyanide concentration to an acceptable level followed by reclamation. However, rinsing does not typically reduce certain metals and compounds, and some constituents may increase in concentration with rinsing. A closure scenario to effect limited infiltration through installation of a capillary cover for the leach pad was developed. The capillary cover was constructed by placing a fine-grained layer above the coarse-grained spent leach material to create a capillary break. In an arid climate such as in Nevada, the fine-grained layer will rarely reach saturation, and the cover will be able to store water during precipitation events and will allow removal of water through evaporation and transpiration (ET) during the growing season. A 1.22-m (4 ft) cover thickness was selected as the optimum design cover thickness. The drainage network on the surface of the recontoured AA heap leach pad was specifically designed to enhance the re vegetation, reclamation and sediment yield control aspects of the AA heap leach pad closure, while resulting in a natural looking surface that is compatible with the surrounding topography. Adjacent natural topographic features were used to establish target design parameters for recontouring and erosion-control design.

Jan 1, 2002

By K. Burke, K. L. Myers, R. Espell

Barrick Goldstrike’s (Goldstrike) AA Heap Leach Pad is an HDPE lined facility used for gold recovery from low grade ores using conventional cyanide heap leach technology, operated from 1987 through 1999. Goldstrike prepared a unique reclamation plan for the AA Leach Pad Facility to provide for a cost-effective, environmentally sound facility closure and to fulfill the State of Nevada’s closure requirements. Traditional Nevada leach pad closure has involved rinsing to reduce cyanide concentration to an acceptable level, followed by reclamation. However, certain metals and compounds are not typically reduced by rinsing and some constituents may increase in concentration with rinsing. A closure scenario to effect limited infiltration through installation of a capillary cover for the leach pad was developed. The capillary cover was constructed by placing a fine-grained layer above the coarse-grained spent leach material to create a capillary break. In an arid climate such as Nevada, the fine-grained layer will rarely reach full saturation and the cover will be able to store water during precipitation and allow removal of water through evaporation and transpiration (ET) during the growing season. A 1.22 m (4 ft) cover thickness was selected as the optimum design cover thickness. The drainage network on the surface of the re-contoured AA Heap Leach Pad was specifically designed to enhance the revegetation, reclamation, and sediment yield control aspects of the AA Heap Leach Pad closure, while resulting in a natural looking surface, compatible with the surrounding topography. Adjacent natural topographic features were used to establish target design parameters for re-contouring and erosion control design.

Jan 1, 2001

By Khosrow Badiozamani

Operating mines in Wyoming and Montana, which are generally characterized by shallow overburden and thick coal seams, are faced with reclamation problems which are unique to this area. Unlike the eastern or midwestern mines, removal of thick coal seams and lack of sufficient overburden creates overburden deficiencies that require careful evaluation prior to mining to insure compliance with regulatory requirements. Computer models and computer graphics can assist in such evaluation where appropriate alternatives can be selected which satisfies both the regulatory requirements and minimizes cost. This paper presents one such model used in evaluation of backfill requirements for restoration of surface and ground water regimes, restoration of mined-out areas to the approximate original contour, and the blending of the mined-out areas to the surrounding topography.

Jan 1, 1981

By I. Ashmole

From the point of view of the environmental impact created, dimension stone mining is a relatively benign industry. There are no emissions besides those of the diesel powered earthmoving equipment utilised in its extraction and a small amount of blasting gases. Contamination of water resources is only likely in the event of petrochemical spillages from storage facilities and equipment, and these can largely be either prevented or cleaned up effectively. The major environmental impacts are of a visual nature, while in sensitive areas, habitat destruction and the destruction of archaeological heritage may become significant impacts. The dimension stone industry has grown at an average rate of over 7% per annum since 1986, and is forecast to continue growing at this rate for the foreseeable future. The cumulative environmental impact of the industry will thus become more significant over time. This paper discusses the environmental impacts of dimension stone mining and recommends effective means for dealing with the practical aspects of reclamation and mine closure in dimension stone mining within the context of environmentally responsible business practices. The discussion focuses mainly on the operations of the Finstone Group in Southern Africa, which are considered to be world leaders in the application of environmental management within the dimension stone mining industry, although reference is also made to other situations which the authors have encountered at dimension stone quarries around the world.

Jan 1, 2008

By A. D. Davis, C. J. Webb, C. S. Johnson, J. L. Porter

The abandoned Belle Eldridge Mine near Deadwood, South Dakota, is on land controlled by the U.S. Bureau of Land Management (BLM) property. The mine produced primarily lead and zinc during the first half of the twentieth century. The BLM has expressed concern about acidic drainage as well as elevated arsenic levels in tailings and waste rock at the site. The mine site was evaluated for remediation in 1998 and 1999. Recent reclamation and remediation work included substantial regrading of waste rock, removal of material where metal loading were of concern, and re-routing of drainage from an adit. Trenching at the site shoed a greater volume than originally calculated during site characterization. Material was removed to a repository that was constructed at a nearby drainage divide. Because of physical hazards, the BLM has decided to remove some historic structures. However, a search of mine records and an inventory of archival materials were complete to preserve the history of the site.

Jan 1, 2002

By Rip Thompson

ALTHOUGH the metallurgical treatment for the Ophir Hill tailings was developed more than 20 years ago and in the interim a vast amount of experimental work was done with later-developed flotation rea-gents, it was found necessary to revert to the original oil reagents and their combina-tions with specific chemical reagents in order to obtain results of economic value. This is of especial interest because in present ore-treatment investigations later-developed flotation reagents are used almost exclusively and the coal-tar deriva-tives, except in certain patented reagents, are virtually neglected. These coal-tar oils and derivatives still have a definite field of application, especially in the treatment of some oxidized ores when modified sulphidi-zation is desirable. The Ophir Hill tailings deposit is in Ophir Canyon, Tooele County, Utah, about 55 miles southwest of Salt Lake City and 25 miles south of the Tooele smelter of the International Smelting and Refining Co. A road good for trucks leads directly from the Ophir mill to the smelter.

Jan 1, 1940

By E. Clarence Peterson, Rip V. Thompson

ALTHOUGH the metallurgical treatment for the Ophir Hill tailings was developed more than 20 years ago and in the interim a vast amount of experimental work was done with later-developed flotation reagents, it was found necessary to revert to the original oil reagents and their combinations with specific chemical reagents in order to obtain results of economic value. This is of especial interest because in present ore-treatment investigations later-developed flotation reagents are used almost exclusively and the coal-tar derivatives, except in certain patented reagents, are virtually neglected. These coal-tar oils and derivatives still have a definite field of application, especially in the treatment of some oxidized ores when modified sulphidization is desirable. The Ophir Hill tailings deposit is in Ophir Canyon, Tooele County, Utah, about 55 miles southwest of Salt Lake City and 25 miles south of the Tooele smelter of the International Smelting and Refining Co. A road good for trucks leads directly from the Ophir mill to the smelter. TAILINGS These tailings were produced in the old Ophir Hill gravity concentrator previous to 1921. The original mill ore was a heavy lead-zinc-copper-silver-iron sulphide ore formed by limestone replacement. The gangue is a highly siliceous lime. An assay of the original milling ore would approximate 1.0 per cent Cu, 6 to 8 per cent Pb, 6 to 8 per cent Zn, 8 to 12 oz. Ag, 18 to 25 per cent Fe, 2.0 per cent CaO, 20 to 5o per cent insoluble. The gold content was 0.005 oz. or less. Tailing was impounded in a fairly wide area in a canyon about ½ mile below the mill. A number of dirt embankments were thrown up to form settling ponds and the tailing was allowed to flow through them in series. Coarser sand deposited at the upper end of the ponds and the finer slimes settled gradually as they passed through the successive settling ponds. As soon as the coarser tailings filled a pond, the tailings were by-passed to the next pond and teams and scrapers were used to haul the deposited sand onto the banks to make them higher. The final dump was approximately 2500 ft. long and 250 ft. wide at the bottoms, with banks sloping up at 45°. The coarser sands predominated at the upper ends and sides of the ponds while the proportion of slimes increased steadily at the lower ends. The lower end of the pond contained over 50,000 tons of slime tailings, 90 per cent of which passed through a 200mesh screen. SAMPLING The entire tailings deposit was sampled by drilling vertical holes so placed as to give data concerning size segregation and the contour of the underlying ground as well as to secure an assay sample. Different types of auger and post-hole drills were tried. None was found satisfactory because the stratified layers of

Jan 1, 1940

By D. G. Deveraux

A BRIEF SKETCH OF THE DAVE JOHNSTON MINE The Dave Johnston coal mine is located near the southwestern extremity of the Powder River Basin in central Wyoming. This mine is operated entirely for the purpose of furnishing fuel to the 750,000 Kw Dave Johnston power generation station located five miles east of Glenrock, Wyoming on the North Platte River about 24 miles east of Casper, Wyoming. Coal is delivered to the power plant by a company-owned railroad moving the coal 15 miles downgrade from the mine to the power plant. The mine first belonging to Pacific Power & Light Company has now been transferred to Northern Energy Resources Company (NERCO), a mining subsidiary of Pacific Power & Light Company. The coal beds which make up the field at the Dave Johnston Mine are locally referred to as the School and Badger seams and occur beneath gently rolling terrain in the Fort Union formation. The School seam is found approximately 180 feet beneath the Badger in the southern portion of the field and about 110 feet beneath the Badger towards the north. The coal beds dip down toward the northeast on about a four percent average inclination. The School seam has an average thickness of about 35 feet and the Badger seam about 16 feet. The climate at the Dave Johnston Mine is semi-arid, with annual precipitation varying between 10 and 12 inches with 70 percent occurring during the months of April to September, with the maximum occurring in May. A few storms occur in July and August which are usually torrential in character, often causing erosion damage to un- protected soils. Snowfall averages 50 inches a year at the mine with 12 to 15 inches of snow yielding one inch of moisture. However, snow seldom

Jan 1, 1983

By Todd A. Duex

The Richmond Hill Mine has recently completed a reclamation plan to mitigate Acid Rock Drainage (ARD) which was identified at the toe of the former waste rock pile in 1992. Reclamation activities began in 1994 with the removal of ARD material from the waste rock pile and placement of this material in the former pit. This material was then isolated from the near surface environment by a low permeability capping system designed to minimize water and oxygen flow into the material. The capping system consists of, from bottom to top, six inches of limestone, 18 inches of low permeability clay liner, 4 and one-half feet of thermal barrier/drain layer, and six inches of topsoil. This capping system was completed in 1995. An extensive program is in place to monitor the effectiveness of the reclamation plan, and includes measurements on moisture content movement, temperature, oxygen content, and groundwater impacts. Monitoring has been ongoing since the completion of reclamation. This monitoring plan is demonstrating the success in isolating the material from the near surface environment and minimizing the impacts to the surrounding environment.

Jan 1, 2000

By Leslie Burnside

Homestake Mining Co. set out to complete final reclamation at a former open-pit gold mine in west central Nevada. The goal was to exceed regulatory standards by satisfying the company's own high corporate standards for successful reclamation. Homestake's completion requirements challenged available technology due to the unsuitability of heap material as a growth medium, the harsh environmental conditions of the site and the region's lack of native growth medium. Accomplishing these goals required enlisting a multidisciplinary project team to develop, test and implement appropriate and cost-effective revegetation alternatives.

Jan 1, 1999

By J. H. Mackey

"Where can I obtain a reclamation bond today?" "Who is writing your bonds?" These questions are common and heard frequently. The fact that the Society of Mining Engineers has determined that two of the five environmental topics reviewed at the 1989 Annual Meeting relate to reclamation bonding indicates to me that those who are involved in the coal industry, no matter what capacity, remain very cognizant of the reclamation bonding dilemma.

Jan 1, 1989

A unique sluicing process for recovering tailing impounded in a valley was developed by Electrolytic Zinc Company of Australasia Ltd., West Coast Mines, Rosebery, Tasmania.Earthmoving equipment could not be used as most of the material to be recovered was semi-fluid. A conventional sluking method was also impracticable as there was no suitable working face from which the process could be commenced.Operations started from a flat surface, using special techniques for sinking through the tailing and establishing producing working faces as the sinking process continued.After about 2 years the bottom of the dam was reached and conventional sluicing methods could be used.

Jan 1, 1973

By E. I. Jurgens, K. E. Hanney, D. C. Comrie, R. H. Fletcher

Introduction The reclamation of mine/mill tailings areas is undertaken for a variety of objectives including safety, appearance, economical use of lands and forests and long term storage of a future resource. The establishing of criteria for these objectives at any site is a shared task of the government and mining company. Our attention in this paper is directed to uranium mine/ mill tailings as they are handled in the Canadian industry and in the unique Canadian climate. We focus our attention on the state of the art. Uranium is a ubiquitous mineral forming an average of 4 g per tonne of the Earth's crust. Ores are mined at about 500 g per tonne so that the residual content of uranium in tailings is comparable to average background levels. However, as in most mine/mill operations, the ore contains other minerals that become readily mobile after milling operations. Thus the main objective of tailings impoundment is the stability both physically and chemically of the mobile materials. Since the requirements for the operation and construction of tailings areas in Canada have changed considerably over the past decade, there exists a great many mine/mill tailings areas which while considered adequate in their day, would not meet modern criteria. However, most of these installations pose no concern or hazard to the public. The proximity of mine/mill development to inhabited land areas has necessitated more stringent modes of tailings operations and provisions for tailings site reclamation. The more important of these have been: 1) the prevention of dyke failure, with large liquid-solid outflows onto adjoining lands, and 2) the prevention of seepage from the tails of pollutants such as chlorides, sulphides, heavy metals and radionuclides. Uranium mill tailings are discharged as a slurry from the concentrator after the removal of generally only about 1000 g, or less, per tonne of uranium from the as-mined ore. As a consequence, a great volume of low level activity waste is generated. The amount of tailings is expected to grow in quantity in the future even faster than the increase in yellowcake production, as the demand for energy

Jan 1, 1980

By Ronald D. Hill, Elmore C. Grim

The cost of reclamation can vary widely, depending on the primary objectives of the restoration activities. statistics in this study originated from State files, publications, and personal communications relating to restoration and pollution control measures for previously mined lands (orphan lands) and active mines. Reclamation of orphan lands is generally considered a public burden and constitutes an economic problem. All work reported here was completed under government contract, by the lowest bidder, with money coming from State and/or Federal funds. Cost would have been substantially lower had the reclamation been concurrent with mining. Several persons connected with some of the projects have observed that costs could probably be reduced by at least one half, if the reclamation had been conducted along with the mining. The expense of clearing and grubbing of volunteer vegetation, disposal of buried trees and brush, loosing of compacted spoil, and re-establishing access to areas could be saved. In addition, a contracting firm doing the work for a government agency would have mobilization costs and receive a profit. Mining companies also are profit conscious and would consider these costs in anticipating their profits (e.g., overhead would be less if reclamation is integrated with mining). The data presented here should serve as a guide for estimating and determining cost ranges, however, it should be recognized that variations exist. Adjustments may be necessary from the standpoint of physical conditions, economic conditions, price changes, and more restrictive requirements of recent surface mining laws. Reclamation conditions, procedures and successes in the eastern United States, particularly in Appalachia, have no bearing on conditions to be expected in the western United States. The situations are wholly different. Reclamation in the West differs from th t in the East, primarily because of aridity especially a during the summer months 1). Because of the many variables and differences between reclamation in eastern and western areas, they will be discussed separately.

Jan 1, 1974

By Robert M. Rudio

Montana is leading the way in the field of mined-land reclamation with new laws and new ideas. The Montana Department of State Lands is combining new legislation and practical application techniques to all mining operations in the state. Road building, stream relocations, or settling systems can be designed to meet the environmental problems. Mineral exploration now requires a new and closer look at drill site locations, road gradients, and exploration tools. The problems and costs of land rehabilitation must be thoroughly understood by the exploration geologist in order to satisfactorily conduct exploration in Montana.

Jan 1, 1975

By G. C. Hambleton

"The author has had wide experience in the reclamation of coal from coal mine waste dumps in the United Kingdom.The paper includes such topics as the processing decision and factors affecting processability; method of testing and appraisal; test data interpretation; historical influences in apppraisal; special contaminants and processing difficulties; methods of treatment; review of systems in use and their comparative economics; over-all system economics including excavation, handling methods, recovery system and shale disposal; effluent treatment; environmental considerations; alternatives to processing for coal recovery; light aggregate and cement usage; burned shale heaps; land reclamation; shale deposition for encouragement of vegetation by natural or artificial means; use of tailings fines; the environmental argument for action."

Jan 1, 1972

By W. B. Boggs

This is a rather comprehensive subject and cannot be thoroughly covered in the short rime allowed for its presentation. This article will touch only upon a few of the chief points of the difficulties encountered in recovering copper from brass shell cases in a primary smelter which was not designed to treat scrap metals. Owing to the fact that the plant is at present (Dec., 1946) closed, and our tests were not completed, full details of the results are not available. As is well known, most primary smelters are situated near the mines in the interior of various countries and are not close to seaports or large industrial and railway centres. Consequently, iris unusual for a primary smelter to be asked to treat scrap metal of any kind. When so required, iris obvious that the primary smelter is at a great disadvantage, for the simple reason that it probably has to pay the freight on the scrap from the seaport or industrial centre to the smelter and then also pay the freight on the recoverable metal from the smelter to the refinery, or seaport or industrial centre. Another disadvantage is that a primary smelter is not equipped to sample and unload the scrap nor bas it usually the equipment adaptable for treating the scrap efficiently, as the plant bas been designed to handle large tonnages of ores and concentrates. This short paper will describe some of our difficulties> and how they were corrected. However, it might be advisable to state briefly some of the methods used in treating brass shell cases in other plants. In the first place, a brass plant producing new brass- especially those producing brass billets for extrusion to make brass tubes or rods, or to be drawn into wire, or making brass cake to roll into brass sheets- generally insists upon using new electrolytic copper and zinc and is opposed to using any scrap or secondary brass . Consequently, such a plant usually will not treat brass shell cases. Therefore, the usual procedure is to ship brass shell cases to a secondary smelter, where it is generally sorted, melted, fire-refined, and returned to the market in the form of a high or low brass ingot which can be sold to brass foundries for making brass castings. This evidently is the cheapest and simplest method. Another method is to ship to a smelter which is a combination of a primary and secondary smelter attached to or near an electrolytic refinery. In plants of both these types, that is a primary smelter with Cottrell dust collectors or a combined primary and secondary smelter with Cottrells or a bag house, the zinc may be wasted. However, if a bag house is used, some of the zinc is recovered, but it is usually contaminated with other metals and further processing is required to recover it.

Jan 1, 1947

By K. L. Ludeke, A. D. Day

For many reasons, it appears that deep rooted, perennial shrubs offer potential for improved stabilization and provide maintenance free vegetative cover to harsh sites where perennial grasses have not been successful. The major objective was to select various shrub species of arid plants for initial soil stabilization of disturbed mining areas. The very fact that a drought-adapted shrub has a massive root system that can use moisture from a greater volume of mineral waste soil materials suggests that arid environment disturbed soils may be vegetatively stabilized using desirable forage shrubs. A secondary effort is underway to assemble information and plant materials of promising species from many arid regions of the world for reclamation of mined lands. Surprisingly, many of the better plants for arid sites are quite high in protein content. With proper management, breeding, and selection, they may prove to be very desirable livestock feed when mined lands are used in range land areas. Advancements in arid land solid waste stabilization hold favorable promise for many industries that mine and mill in arid regions for effective reclamation of disturbed areas. Particularly exciting is the possibility of establishment of high density maintenance free vegetative cover of climax vegetation that reclaims the disturbed area back to its original land use. Due to high shrub productivity, stabilization potential, nutritional quality, and reclamation success, greater use should be made of shrubs in disturbed land reclamation associated with mining and milling operations in harsh aril environments.

Jan 1, 1986

By Bland Z. Richardson

Jan 1, 1985