Search Documents

By L. C. McCabe

This paper is a progress report on a study of the distribution of the banded ingredients (Figs. 1 and 2) in Illinois screenings and the method of determining their distribution. Proximate analyses and screen tests1 have been reported and a further report on the washability characteristics of the screenings is in preparation. The microscopic study of the screenings is not yet far enough advanced to permit a conclusive report on the effect of mining, screening and washing on the distribution of the banded ingredients in the coals of Illinois. However, considerable fundamental data have been collected as a background for the screenings investigation and for a proposed study of fuels composed of known quantities of vitrain, clarain and fusain, the three common banded ingredients of Illinois coals. These fundamental data and the preliminary information now available from the microscopic study of screenings are broadly indicative of the reaction of the coals to the physical processes affecting them in mining and preparation. Proximate analyses of samples of vitrain, clarain, and fusain from several Illinois mines have been published2, but those given in Table 1 serve to show the differences that are apparent in proximate analyses. The vitrain samples are consistently low in ash, and the unit-coal value is uniformly lower than in clarain. The average fuel ratio (F.C./V.M.) of the vitrain samples in the table is 1.57 whereas the clarain average is 1.42. The fusain analyses vary considerably in ash and moisture. In the two samples from this mine the moisture values range from 8.99 to 22.80 and the ash from 4.86 to 16.91 per cent. Fusain has higher fixed carbon than either vitrain or clarain but the percentage is erratic from sample to sample. The relative proportions of the banded ingredients in the Herrin (No. 6) coal in Illinois is reasonably well known but detailed information

Jan 1, 1936

By L. C. McCabe

This paper is a progress report on a study of the distribution of the banded ingredients (Figs. 1 and 2) in Illinois screenings and the method of determining their distribution. Proximate analyses and screen tests1 have been reported and a further report on the washability characteristics of the screenings is in preparation. The microscopic study of the screenings is not yet far enough advanced to permit a conclusive report on the effect of mining, screening and washing on the distribution of the banded ingredients in the coals of Illinois. However, considerable fundamental data have been collected as a background for the screenings investigation and for a proposed study of fuels composed of known quantities of vitrain, clarain and fusain, the three common banded ingredients of Illinois coals. These fundamental data and the preliminary information now available from the microscopic study of screenings are broadly indicative of the reaction of the coals to the physical processes affecting them in mining and preparation. Proximate analyses of samples of vitrain, clarain, and fusain from several Illinois mines have been published2, but those given in Table 1 serve to show the differences that are apparent in proximate analyses. The vitrain samples are consistently low in ash, and the unit-coal value is uniformly lower than in clarain. The average fuel ratio (F.C./V.M.) of the vitrain samples in the table is 1.57 whereas the clarain average is 1.42. The fusain analyses vary considerably in ash and moisture. In the two samples from this mine the moisture values range from 8.99 to 22.80 and the ash from 4.86 to 16.91 per cent. Fusain has higher fixed carbon than either vitrain or clarain but the percentage is erratic from sample to sample. The relative proportions of the banded ingredients in the Herrin (No. 6) coal in Illinois is reasonably well known but detailed information

Jan 1, 1936

By H. F. Yancey, M. R. Greer

At the annual meeting of this Institute held two years ago a new method1 of estimating the grindability of coal was described, based on experimental work carried on by the Bureau of Mines at its Northwest Experiment Station. Since that time, several organizations concerned with the testing or utilization of coal as pulverized fuel have adopted and used the method in determining the grindability of several hundred samples of coal. In addition, a series of comparative tests of this method and three others has been carried out in five laboratories under the auspices of Committee D-5 of the American Society for Testing Materials. As a result the Committee has recommended that the Bureau of Mines method, designated as the "ball-mill method," and the Hardgrove method2, previously advanced, be accepted as tentative standards3. Since the ball-mill method was originally developed and published, an opportunity has been presented to apply it to a larger number of coals and to study intensively some of the principles upon which the method is based. This paper presents a résumé of these further studies and includes a comparison with the Hardgrove-machine method. Trial runs were also made with another procedure recently proposed—the C.I.T. roll-test method4. Principles of Methods In the ball-mill method, the relative amounts of energy necessary to grind coals to the same fineness are determined by the number of revolutions of the mill required to reduce 80 per cent of the feed (500 grams of 10 to 200-mesh coal) fine enough to pass a 200-mesh screen. This is a

Jan 1, 1936

By H. F. Yancey, M. R. Greer

At the annual meeting of this Institute held two years ago a new method1 of estimating the grindability of coal was described, based on experimental work carried on by the Bureau of Mines at its Northwest Experiment Station. Since that time, several organizations concerned with the testing or utilization of coal as pulverized fuel have adopted and used the method in determining the grindability of several hundred samples of coal. In addition, a series of comparative tests of this method and three others has been carried out in five laboratories under the auspices of Committee D-5 of the American Society for Testing Materials. As a result the Committee has recommended that the Bureau of Mines method, designated as the "ball-mill method," and the Hardgrove method2, previously advanced, be accepted as tentative standards3. Since the ball-mill method was originally developed and published, an opportunity has been presented to apply it to a larger number of coals and to study intensively some of the principles upon which the method is based. This paper presents a résumé of these further studies and includes a comparison with the Hardgrove-machine method. Trial runs were also made with another procedure recently proposed—the C.I.T. roll-test method4. Principles of Methods In the ball-mill method, the relative amounts of energy necessary to grind coals to the same fineness are determined by the number of revolutions of the mill required to reduce 80 per cent of the feed (500 grams of 10 to 200-mesh coal) fine enough to pass a 200-mesh screen. This is a

Jan 1, 1936

By Gilbert Thiessen

The use of a pneumatic process for removing fine material (usually less than 48-mesh) is increasing in the preparation of stoker-size coal. The fine material, produced as a byproduct, is known as dedusting-plant dust. Since fusain is the most friable ingredient in bituminous coal (it may readily be rubbed to an impalpable powder with the fingers), it tends to accumulate in this byproduct. While studying the properties of cokes produced by blending Illinois coals with other materials, considerable quantities of fusain were required. Dedusting-plant dust suggested itself as a convenient supply. It became necessary, therefore, to determine how much fusain was contained in a measured sample of dust, how the fusain was distributed with respect to size and specific gravity in the sample, and whether or not it would be feasible or desirable further to concentrate or to recover the fusain from the dust before using it in the blends to be coked. The results obtained indicate the possibilities of production of a high-fusain material. Previous Work Lehmann and Stach have developed a processl,2 for separation of banded bituminous coals into their band ingredients by impact pulverization followed by screening or air separation. They found, as might be expected, that the fusain was concentrated in the very fine material. Prockat and Raute3 examined samples from dedusting plants operating in the Ruhr. They separated the dust into various screen sizes and determined the composition of each of these sizes in terms of the banded ingredients of the original coal. In the dusts examined by them, the finest material was always high in fusain, and most of the fusain contained in the original samples could be recovered from this fraction.

Jan 1, 1936

By Gilbert Thiessen

The use of a pneumatic process for removing fine material (usually less than 48-mesh) is increasing in the preparation of stoker-size coal. The fine material, produced as a byproduct, is known as dedusting-plant dust. Since fusain is the most friable ingredient in bituminous coal (it may readily be rubbed to an impalpable powder with the fingers), it tends to accumulate in this byproduct. While studying the properties of cokes produced by blending Illinois coals with other materials, considerable quantities of fusain were required. Dedusting-plant dust suggested itself as a convenient supply. It became necessary, therefore, to determine how much fusain was contained in a measured sample of dust, how the fusain was distributed with respect to size and specific gravity in the sample, and whether or not it would be feasible or desirable further to concentrate or to recover the fusain from the dust before using it in the blends to be coked. The results obtained indicate the possibilities of production of a high-fusain material. Previous Work Lehmann and Stach have developed a processl,2 for separation of banded bituminous coals into their band ingredients by impact pulverization followed by screening or air separation. They found, as might be expected, that the fusain was concentrated in the very fine material. Prockat and Raute3 examined samples from dedusting plants operating in the Ruhr. They separated the dust into various screen sizes and determined the composition of each of these sizes in terms of the banded ingredients of the original coal. In the dusts examined by them, the finest material was always high in fusain, and most of the fusain contained in the original samples could be recovered from this fraction.

Jan 1, 1936

By C. G. Black

The purpose of this paper is to present data obtained from an investigation conducted on the grindability of coal by the American Society for Testing Materials Tentative Standard ball-mill method. This investigation has been conducted over a period of a year, during which time several hundred tests were run on a wide selection of different coals coming from Pennsylvania, Ohio, West Virginia and Kentucky. The data herewith presented tend to show that the tentative standard ball-mill method might give results that are misleading and that a volume measure might be more indicative of the true grindability of materials of varying specific gravity. A means whereby the time element might be reduced has been studied and other phases of this work such as preparation of samples, mechanical screening, reporting results and duplicating tests have been investigated. It is hoped that all criticism offered in this paper will be taken as constructive, with the purpose ill mind of perfecting the method now tentative to show the true conditions 2nd of making optional the manner in which certain parts of the test might be conducted to meet diversified laboratory conditions. Weight and Volume The results of grindability on extraneous material from the coal scam obtained with the present tentative standard ball mill method indicate easier grinding of these materials as compared to most coals. Varying amounts of these impurities in the coal therefore may cause a raising of the grindability index and may lead to the erroneous conclusion that coals containing large amounts of these foreign materials are easier to grind. For a true comparison of grindability, it would seem necessary to grind to the same particle weight. If material were sized in a commercial mill by means of an air current set at a velocity to remove 1.60 sp. gr. float coal ground to 80 per cent minus 200 mesh, any 1.60 sink particles would be left behind, and in order to remove this 1.60 sink material by the same current it would be necessary to grind finer and produce a

Jan 1, 1936

By C. G. Black

The purpose of this paper is to present data obtained from an investigation conducted on the grindability of coal by the American Society for Testing Materials Tentative Standard ball-mill method. This investigation has been conducted over a period of a year, during which time several hundred tests were run on a wide selection of different coals coming from Pennsylvania, Ohio, West Virginia and Kentucky. The data herewith presented tend to show that the tentative standard ball-mill method might give results that are misleading and that a volume measure might be more indicative of the true grindability of materials of varying specific gravity. A means whereby the time element might be reduced has been studied and other phases of this work such as preparation of samples, mechanical screening, reporting results and duplicating tests have been investigated. It is hoped that all criticism offered in this paper will be taken as constructive, with the purpose ill mind of perfecting the method now tentative to show the true conditions 2nd of making optional the manner in which certain parts of the test might be conducted to meet diversified laboratory conditions. Weight and Volume The results of grindability on extraneous material from the coal scam obtained with the present tentative standard ball mill method indicate easier grinding of these materials as compared to most coals. Varying amounts of these impurities in the coal therefore may cause a raising of the grindability index and may lead to the erroneous conclusion that coals containing large amounts of these foreign materials are easier to grind. For a true comparison of grindability, it would seem necessary to grind to the same particle weight. If material were sized in a commercial mill by means of an air current set at a velocity to remove 1.60 sp. gr. float coal ground to 80 per cent minus 200 mesh, any 1.60 sink particles would be left behind, and in order to remove this 1.60 sink material by the same current it would be necessary to grind finer and produce a

Jan 1, 1936

By Martin A. Mayers

Five-sixths of all the coal that is mined in the United States is burned, without previous treatment other than screening, for the production of heat and power, so that its value is fixed by its suitability for this purpose. Nevertheless, the characteristics of individual coals that determine their fitness for use in particular pieces of combustion equipment are not yet well known. This condition is due not only to the small extent of our knowledge concerning coal itself, but also to our comparative ignorance of the nature of the combustion process. The following paper is an analysis of the combustion process as it occurs in industrial furnaces, based largely on the results of laboratory research on combustion rates. From this analysis it is possible to determine the characteristics of the fuel that limit the capacity of a given piece of combustion equipment. Limitations imposed by other factors than the attainable speed of combustion will not be considered, since they are subject to a different type of analysis involving the balancing of maintenance costs against fixed charges. In order to observe the relations among the various factors that affect the speed of combustion, representative particles of fuel will be followed through two types of furnaces. A pulverized-coal furnace will be considered first, because the independence of the individual particles facilitates the analysis of the effect of furnace conditions. The second example will be a grate-fired furnace in which ignition of the fuel takes place on the underfeed principle. This includes both underfeed and chain grate stokers, (8)† but does not include hand-fired furnaces and some overfeed stokers. The furnace will be considered to be large enough, the temperature high enough, and enough air provided, to burn the fuel completely, without, for the moment, specifying these quantities more completely. Furnaces Burning Pulverized Coal In a pulverized-coal furnace, the fuel particle is carried, in a stream of air, into the furnace, where it is subjected to radiation from the flame and from the hot walls of the furnace. The increase of particle tempera-

Jan 1, 1936

By Martin A. Mayers

Five-sixths of all the coal that is mined in the United States is burned, without previous treatment other than screening, for the production of heat and power, so that its value is fixed by its suitability for this purpose. Nevertheless, the characteristics of individual coals that determine their fitness for use in particular pieces of combustion equipment are not yet well known. This condition is due not only to the small extent of our knowledge concerning coal itself, but also to our comparative ignorance of the nature of the combustion process. The following paper is an analysis of the combustion process as it occurs in industrial furnaces, based largely on the results of laboratory research on combustion rates. From this analysis it is possible to determine the characteristics of the fuel that limit the capacity of a given piece of combustion equipment. Limitations imposed by other factors than the attainable speed of combustion will not be considered, since they are subject to a different type of analysis involving the balancing of maintenance costs against fixed charges. In order to observe the relations among the various factors that affect the speed of combustion, representative particles of fuel will be followed through two types of furnaces. A pulverized-coal furnace will be considered first, because the independence of the individual particles facilitates the analysis of the effect of furnace conditions. The second example will be a grate-fired furnace in which ignition of the fuel takes place on the underfeed principle. This includes both underfeed and chain grate stokers, (8)† but does not include hand-fired furnaces and some overfeed stokers. The furnace will be considered to be large enough, the temperature high enough, and enough air provided, to burn the fuel completely, without, for the moment, specifying these quantities more completely. Furnaces Burning Pulverized Coal In a pulverized-coal furnace, the fuel particle is carried, in a stream of air, into the furnace, where it is subjected to radiation from the flame and from the hot walls of the furnace. The increase of particle tempera-

Jan 1, 1936

By H. H. Lowry

Science attracts the attention and interest of an individual or an industry in general only in proportion to the apparent direct application to its immediate welfare or benefit. Engineering accomplishments, as aphlied science, therefore receive more recognition than the scientific discoveries on which they are based. Even self-evident truth needs endless repetition before recognition: engineering as applied science cannot advance beyond the science on which it is founded. Scientific research, and discovery, is sometimes forced by the limitations recognized by those active in its development for the use of society and industry and sometimes results from an apparently superficially illogical curiosity about natural phenomena. Research has received inadequate support except in industries born in the laboratory, the chemical and electrical industries, from which many lessons might well be drawn by their elder associates. The rapid growth of these industries has been largely due to close cooperation of scientists and engineers. Most rapid advance is made when the research worker and the engineer keep in close touch with each other's ideas and problems. Many of the developments of modern industry are based on discoveries buried for years in scientific journals because the "time was not ripe" at their discovery. The situation with regard to utilization of coal is quite the oppositre. The fundamental facts in regard to the scientific aspects of the problem of developing the energy from coal are scarcely known. The engineer, without much scientific cooperation, has accomplished much in increasing the number of kilowatt-hours per pound of coal from 0.31 in 1919 to 0.69 in 1934, in increasing the 1000 gross ton-miles of freight hauled from 12.2 to 16.4 per ton of coal in the same period, in fuel economy in production of coke, and in developing the production of motor fuel in Germany and England by hydrogenation of coal. This lack of scientific research on the utilization of our most important natural resource, coal, has been due undoubtedly in large part to the reluctance of investigators to study the interrelationships involved in the complicated processes in which coal is used. These complexities are made

Jan 1, 1936

By H. H. Lowry

Science attracts the attention and interest of an individual or an industry in general only in proportion to the apparent direct application to its immediate welfare or benefit. Engineering accomplishments, as aphlied science, therefore receive more recognition than the scientific discoveries on which they are based. Even self-evident truth needs endless repetition before recognition: engineering as applied science cannot advance beyond the science on which it is founded. Scientific research, and discovery, is sometimes forced by the limitations recognized by those active in its development for the use of society and industry and sometimes results from an apparently superficially illogical curiosity about natural phenomena. Research has received inadequate support except in industries born in the laboratory, the chemical and electrical industries, from which many lessons might well be drawn by their elder associates. The rapid growth of these industries has been largely due to close cooperation of scientists and engineers. Most rapid advance is made when the research worker and the engineer keep in close touch with each other's ideas and problems. Many of the developments of modern industry are based on discoveries buried for years in scientific journals because the "time was not ripe" at their discovery. The situation with regard to utilization of coal is quite the oppositre. The fundamental facts in regard to the scientific aspects of the problem of developing the energy from coal are scarcely known. The engineer, without much scientific cooperation, has accomplished much in increasing the number of kilowatt-hours per pound of coal from 0.31 in 1919 to 0.69 in 1934, in increasing the 1000 gross ton-miles of freight hauled from 12.2 to 16.4 per ton of coal in the same period, in fuel economy in production of coke, and in developing the production of motor fuel in Germany and England by hydrogenation of coal. This lack of scientific research on the utilization of our most important natural resource, coal, has been due undoubtedly in large part to the reluctance of investigators to study the interrelationships involved in the complicated processes in which coal is used. These complexities are made

Jan 1, 1936

By C. P. Proctor, J. B. Morrow

With numerous plans under consideration for coal classification, and with the advent of the Bituminous Coal Code, the intelligent sampling of coal has become increasingly important. To us it is rather significant that there have been very few fundamental studies of coal sampling in American technical literature since those of E. G. Bailey, which appeared in the Journal of Industrial and Engineering Chemistry in March, 1909. He covered the subject up to that time so thoroughly and in such an excellent manner that perhaps many other later students have felt that they could add very little to his findings. The recent studies of the British Engineering Standards Association have indicated the possibility of a somewhat different interpretation of Bailey's results, permitting the taking of smaller samples, and perhaps it will now be helpful to reopen this question. C. W. H. Holmes, in an informative series of articles on coal sampling recently published in Colliery Engineering, makes two rather interesting statements, as follows: It is scarcely surprising to find a lack of interest and knowledge regarding the sampling of coal not only in the mining industry itself but also among consumers of industrial fuel: at its best coal sampling is a dirty business, regarded as a nuisance and an expense by the commercial man, and usually as a nuisance and nothing else by the chemist. The writer can conceive only two classes of people who have never experienced any difficulty in obtaining representative samples of coal from wagons; those who have never tried to, and those who have never had the necessity or desire to check the accuracy of their work. The primary purpose of this paper is to present some tabulated data of the more significant results of a sampling investigation undertaken during the last four years to obtain certain fundamental data on the variables connected with coal sampling and to point out that often assumptions have been made that are not in accordance with the facts. One of the standard sampling methods states:

Jan 1, 1936

By C. P. Proctor, J. B. Morrow

With numerous plans under consideration for coal classification, and with the advent of the Bituminous Coal Code, the intelligent sampling of coal has become increasingly important. To us it is rather significant that there have been very few fundamental studies of coal sampling in American technical literature since those of E. G. Bailey, which appeared in the Journal of Industrial and Engineering Chemistry in March, 1909. He covered the subject up to that time so thoroughly and in such an excellent manner that perhaps many other later students have felt that they could add very little to his findings. The recent studies of the British Engineering Standards Association have indicated the possibility of a somewhat different interpretation of Bailey's results, permitting the taking of smaller samples, and perhaps it will now be helpful to reopen this question. C. W. H. Holmes, in an informative series of articles on coal sampling recently published in Colliery Engineering, makes two rather interesting statements, as follows: It is scarcely surprising to find a lack of interest and knowledge regarding the sampling of coal not only in the mining industry itself but also among consumers of industrial fuel: at its best coal sampling is a dirty business, regarded as a nuisance and an expense by the commercial man, and usually as a nuisance and nothing else by the chemist. The writer can conceive only two classes of people who have never experienced any difficulty in obtaining representative samples of coal from wagons; those who have never tried to, and those who have never had the necessity or desire to check the accuracy of their work. The primary purpose of this paper is to present some tabulated data of the more significant results of a sampling investigation undertaken during the last four years to obtain certain fundamental data on the variables connected with coal sampling and to point out that often assumptions have been made that are not in accordance with the facts. One of the standard sampling methods states:

Jan 1, 1936

By N. I. Tyushkova

On the basis of detailed studying of mineral structure of ore and treatment products it is established that the given ore refers to oxidized Pb-Zn vein-disseminated ores. Technological special features of the basic ore minerals and the reasons causing their obstinateness that is defined by following features are revealed, presence at dominating quantity difficult to float lead minerals: mimetesite (9.67%), green lead ore(0.48%); non float: bindheimite (2.16%) and plumbojarosite (0.36%) and high assay of oxides and hydrous ferric oxides; also thin, emulsive and submicroscopic segregations of the defined minerals in swamp ore. As a result of researches the scheme of gravitational-flotation treatment was conducted in semi-industrial scale. It allows to receive two concentrates from ore: a lead gravitational concentrate of mark ??-4 with the assay of 55.5 % of Pb and 0.77 % of Zn; and a Pb concentrate of mark ??-7 with assay of Pb of 40.97 % and Zn of 1.39 %. The total assay of Pb in concentrates makes 81 %. The efficiency offered by gravitational-flotation schemes is defined by possibility for recovery of big impregnated lead minerals under gravitation. The use of this method of gravitation has allowed to recover such mineral as beudantide and to exclude irrevocable losses of lead in tails which are connected with this mineral. Scientific value of the presented researches is connected with the fact the problem of extraction of the oxidized minerals of Bb and Zn is rather difficult and insufficiently studied. Keywords: flotation, oxidized forms of Pb and Zn

Sep 1, 2012

By N. J. Themelis, W. H. Dresher

Research is probably the least understood and the most underrated or overrated, depending on the circumstances, function of the corporate enterprise. Some companies become engaged in research because they consider it to be vital to their very existence, others in order to develop new business, and some with no clearer objective than to keep up with the competition. Whole new industries have resulted from research activities, such as the Xerox copier, the transistor, the computer, and have affected considerably our way of life. Companies have prospered or perished by pursuing the successes or failures of their research organizations. However. despite the tremendous effect that research has had on our modern civilization and the billions which are spent on it annually, we have not as yet been able to develop many hard and fast rules as to how to conduct it effectively and to a successful end.1 This section discusses the role of research in the United States and in the mineral industry and describes a few of the criteria and guidelines which have been developed to assist in increasing the probability for success in industrial research. Broadly speaking, the purpose of industrial research is to make a significant contribution to the long-term viability and the profitability of the sponsoring company. The sum total of technological developments has been a principal factor in establishing the United States as a world leader and the controlling element in the nation's balance of trade with foreign powers. The international aspect of most mineral commodities is a significant factor in the business decision-making of most domestic mining companies and should be an important factor in the operation of research and development (R & D) programs in these companies. The National Science Board has reported that in recent yean other nations have been gaining on the United States over practically the entire range of science. 2,3 On the positive side, the NSB reported a strong position for the US in the results derived from its investment in R & D. If the United States is to maintain a favorable trade balance, it must create new know-how through technological innovation in order to create new industrial products, processes, and services for which there is a global demand. As expressed by Chauncey Starr, president of the Electric Power Research Institute, "Unlike resources found in nature, technology is a man-made resource whose abundance can be continuously increased, and whose importance in determining the world's future is also increasing."' In recent years, the greatly in- creased pressures for environmental quality and energy conservation have enhanced further the role of technical innovation in insuring the future survival of the domestic industry. Technology is the challenge of American industry, and it is a challenge which the mineral industry must also accept, for processed minerals are the very raw materials and energy on which all of industry is based, it is technology which makes a mineral deposit into an ore reserve. The Natural of Industrial R D Research is usually thought of as being either basic or applied. Basic or fundamental research is the quest for knowledge and need not have any practical objective. Applied research is the search for a solution to a particular problem and therefore has a specific objective beyond the acquisition of new knowledge. Development is the next stage to the applied research experimentation and it generally consists of larger-scale tests to establish the technical and economic feasibility of the new process or product and to provide design information for its industrial implementation. The terms research and development are usually interconnected for the good reason that in many cases it is difficult to define where one ends and the other begins. For instance, in many cases, thermodynamic, kinetic, corrosion, and other research studies, which are needed to provide design data for an industrial plant, may prod in parallel with the pilot plant activities preparatory for this plant in order to conserve time. Often the final stages of a development project may involve the trial production of a new product for markeing tests or the trial operation of a new process on a "semi-industrial" scale pilot plant. Such operations may be termed "demonstrations"; hence, more

Jan 1, 1985

By Thomas C. Atchison, James J. Olson

INTRODUCTION Technologic progress depends on new and innovative ideas, the practical application of these ideas, and finally as the technology is developed and demonstrated, the engineering improvement or replacement of existing capabilities. In many areas the new ideas, although known, are not immediately put to practical use in all applicable fields. Good technologic forecasting for research and development within the excavation field coupled with adequate technology transfer is necessary to ensure timely application of innovative ideas to remove bottlenecks in the total system. The purposes of this paper are (1) to show the potential ability of technologic forecasting to meet future demands in rapid excavation through the acceleration of excavation rates by research and development in several related technologic fields, (2) to provide a brief review of the initial development of the ARPA (Advanced Research Projects Agency) Rock Mechanics and Rapid Excavation Program, (3) to draw attention to the research projects completed or underway in the FY 1970-1972 ARPA program and explain where information or program results can be obtained, (4) to summarize the progress and accomplishments of applied research contracts in the rock disintegration element of the ARPA program, and (5) to discuss the research directions planned for the remaining years of the program. The Advanced Research Projects Agency (ARPA) is a group within the Defense Department responsible for conducting basic and applied research and development for advanced projects assigned by the Director

Jan 1, 1997

By R. D. Brown

"An adequate level of R & 0 is crucial to achieve gains in productivity and to strengthen Canada' s position in an increasingly competitive world ." So stated Finance Minister Jean Chretien in his April 10, 1978 budget speech, on announcing a new measure designed to increase the productivity of Canadian industry and to assist in the creation of new technology. The effect of the new measure, which permits an income tax deduction of 150% of certain research and development (R & D ) expenditures , can reduce the after-tax cost of a marginal dollar 's worth of such expenditures to as little as 20 cents . This article discusses the income tax treatment of R& D expenditures in general, and describes in particular the income tax incentives which relate to R& D.

Jan 1, 1978

By Dennis E. Mitchell

The need to develop and field explosive, pyrotechnic and propellant initiating systems that have high reliability and extraordinary safety requirements has led to the exploration and development of several materials and initiation systems at our laboratories. Our approach to initiating device development encompasses five main areas; energetic materials development , device physics, theoretical analysis and model development and experimental verifications

Jan 1, 1995

By M. J. Virnig, Marc Le Vier, Rong Yu Wan, Jan D. Miller

Although most gold production from primary resources is achieved by cyanidation, many research activities have focused on alternative processes using noncyanide lixiviants. Such research has been prompted by environmental concerns and problems associated with the processing of refractory gold ores. Numerous research projects have been conducted to search for a noncyanide hydrometallurgical process for gold extraction. In this paper, a technical review of gold recovery from noncyanide solutions is presented, and new results are reported. Gold recovery techniques that are considered include activated carbon adsorption, cementation, solvent extraction, ion exchange, and reduction-precipitation.

Jan 1, 1993