Search Documents

By S. Z. Shkundin

An evaluation of the accuracy of tachometric and hot-wire anemometers in mine workings and gas-media ducts is given. The acoustic means of gas flow rates measurement is considered with particular reference to the equations of acoustic waves propagation in aerodynamic fields. The paper defines how it is possible to minimize the error of integrating acoustic anemometers.

Sep 1, 2001

By W. D. Delahaut

Sampling tests performed at the Paradise Peak Mine compared various blasthole samplers and reverse circulation sampling methods. Statistical analysis of the data indicates that be-low-the-deck bag sampling produced a 24 to 29 percent error when compared to bulk sampling methods. Use of a chip pile wedge sampler reduced error to 17 percent. Reverse circulation sampling upgraded over bulk blasthole sampling by 7 percent for gold and 11 percent for silver. These results indicate that bias sampling conditions exist when small volume bag sampling is employed in production blasthole drilling.

Jan 1, 1991

By E. Rubenstein, V. Gangrade, K. V. Raj, M. L. Harris

Underground stone mine ventilation is characterized by large openings with low resistances. These mines primarily face three challenges: moving adequate volumes of air, controlling and directing the airflow, and planning ventilation systems that work well with production requirements. Given these challenges, this paper examines the data collected by the Mine Safety and Health Administration (MSHA) to determine the extent to which respirable crystalline silica (RCS) and diesel particulate matter (DPM) are an issue in underground stone mines. Out of 522 sampled mines, there were 108 personal samples exceeding the RCS Permissible Exposure Limit (PEL) during 2000–2020. DPM were more prevalent than RCS in these mines with 382 personal samples exceeding the DPM PEL out of the 929 mines sampled during 2002–2020. Dilution of DPM is usually the defining parameter for design of mine ventilation systems in largeopening underground stone mines. With this knowledge, focused attention can be directed to these mines so that appropriate prevention and mitigation techniques can be utilized to prevent stone miners’ exposure to RCS and DPM and subsequent respiratory diseases.

Mar 2, 2022

By Baafi E. Y

Dragline monitoring systems are normally the best tool used to collect data on the machine performance and operational parameters of a dragline operation. This paper discusses results of a time study using data from a dragline monitoring syste

Jan 1, 1998

By Melanie Grob

Two commonly estimated fractal dimensions, called b and D values, represent statistical characteristics in the distribution of magnitude sizes (b) and spatial hypocenter locations (D) of microseismic events, respectively. We postulate that the values of b and D are related to specific stress regimes. Through different case studies of fluid injection into an oil/gas reservoir or geothermal field, we infer that the measured temporal variation in fractal dimension b is most likely due to significant changes in the local stress regime. The fracture dimension D indicates the spatial clustering of events. The distribution of these events can vary with time because of stress perturbations that (re)activate fractures whose direction favours their movement under a specific stress regime. Thus a combined statistical study of these two dimensions can help infer the variations of local stresses in a reservoir.

Jun 1, 2012

By Dickson T. J

Slag cleaning is an important part of the pyrometallurgical operations at the Kalgoorlie Nickel Smelter. It is a complex system with many streams of different phases and composition. Some of these streams are very difficult to control and/or monitor. Through the use of a statistical computer package, called Minitab, key relationships affecting the economical operation of the slag cleaning process have been found. Data for the statistical analysis was collected from all possible variables around the appendage.

Jan 1, 1991

By M. Tirmarche, J. Brenot, J. W. Piechowski

INTRODUCTION Statistical analysis of results obtained by workers survey is very often limited to the determination of the collective dose and mean annual values. This information is not sufficent by itself for radiation protection purposes since the cumulative exposure of a worker during his working life is not taken into account. A more complete analysis would be obtained by considering both: [ ] These two notions are different. The former depends on the evolution of the protection with time and is related to annual limits (ICRP, 1977 and ICRP,1977 a). The second depends mainly on the works performed during the period of survey, the interference of protection evolution is weakened. So it is useful to foresee how the individual average annual doses would be when considering survey periods of 5, 10 years, or more. STUDIED POPULATION In order to analyse the two previously mentionned notions it is necessary to follow up a well defined population of workers which is continuously exposed to the radiological hazards on a long enough period. The selected population is that of the workers of the French uranium mines always present during the 1971-1979 period (9 years). The number of individuals is 937. The radiological hazards are: 1. exposure to radon and short-lived daughters 2. exposure to long-lived ore dust 3. external irradiation. The workers of the uranium mines are exposed to these radiological risks in different ways according to the work performed. It is therefore necessary to subdivide the population into more homogeneous groups with respect to the radiological risks. Three groups are considered: - Group 1 : 227 individuals whose radon and dust exposures are always nil - Group 2 : 449 individuals whose radon and (or) dust exposures are different from 0 every year - Group 3 : 261 individuals represent a mixed category. Some features of these groups are given in table 1. [ ] The 937 followed individuals represent approximatively the half of the whole population of the French uranium mines. Taking into account the procedure adopted to select the studied population, it appears clearly that this population is not representative of the whole miner population. DOSIMETRIC RECORDS Three risk indicators are considered .Individual annual exposures to radon and its shortlived daughters. They are determined by ambient monitoring based on radon concentration measurements and recording of the times elapsed in the various workplaces. For each worker the annual exposure is represented by the mean annual air concentration and is expressed as a fraction of the maximum annual concentration (MAC). Given the administrative arrangements and the effective state of equilibrium between radon and its daughters, the maximum annual concentration is practically equivalent to 1 Working Level = 2.08 x 10- 5 jm-3. (UNSCEAR, 1977). . Individual annual exposures to long-lived ore dust which are also expressed in fraction of the maximum annual concentration. . Individual annual doses of external irradiation (X and [y] rays) expressed in mSv (= 10-3 Sievert). Irradiation monitoring is based on use of individual film badges.

Jan 1, 1981

During the drilling campaign conducted between October, 1942; and May, 1943, to prove the extent of the scheelite deposit worked by King Island Scheelite N.L. at Grassy, King Island, Tasmania, 35 holes were drilled and 606 samples recovered and assayed for their content. Of these, 238 came from outside the limits of the orebody and were for the most part barren, although a few contained some scheelite. The present statistical analysis is made only of the 368 samples taken from diamond-drill cores of the orebody itself.Drilling Pattern and Sampling MethodsFrom the purely statistical viewpoint, it is realised that methods employed in selecting sites for diamong.-drilling, and of collecting samples from drill cores, do not give a completely unbiassed set of data for analysis. Fig. 1 is a sketch plan showing the relativepositions of the drillholes, which were inclined at an angle of depression of 50 deg. The pattern does not conform to a properly randomized and' regularly-spaced grid, the positions of the later holes being determined by the results obtained from previous holes.Statistically, the bias is, therefore, favourable. The unequal spacing of the drill holes and the lack of uniformity in direction of the lines along which the holes were drilled are unsatisfactory from the mathematical viewpoint; but it is realised that these irregularitiesare difficult to avoid in determining by the most economical methods the extent of such an orebody, and are dictated by geological rather than mathematical necessity.Sampling, also, is lacking in complete uniformity. Each sample is approximately 10ft. in length. However, owing to the fact that 100% recovery of core is rarely achieved, and actual lengths of samples taken are ,primarily governed by the length of the drill runs,and secondarily by lithological changes, there is a considerable amount of variation in the sample length.AssayingWith the exception of 28 samples from three drill holes all samples dealt with in this paper were assayed in the Melbourne University Ore-Dressing Laboratory of the Commonwealth Scientific and Industrial Research Organisation. These assays were given to the nearest 0.05% WOg as it was considered that more accurate determination was not possible. This fact has been taken into consideration in the frequency analysis below. The 28 assays determined by the Tasmanian Mines Department were given to the nearest 0.01%.

Jan 1, 1950

By James D. Bliss

Sedimentary deposits of pluvial Lake Bonneville are an important source of sand and gravel suitable for aggregate and construction in Utah. Data on Lake Bonneville basin sand and gravel deposit thickness, volume, grain size, percent of fines, and durability were statistically analyzed to detect variations associated with geologic domains, geographic location, Lake Bonneville shorelines, and sand and gravel deposit type, and to construct quantitative deposit models. Analysis showed several trends; (1) sand and gravel in younger shorelines was slightly more durable and the deposits considerably larger in volume, (2) younger shore- lines are also more likely to contain more than one genetic deposit type, (3) the volume of terrace deposits is larger than beach deposits, (4) terraces and beaches are generally thicker than spits and bars, (5) the northern part of the Bonneville Basin contains slightly more durable sand and gravel than the southern part of the basin and is more likely to contain deposits composed of more than one genetic deposit type, aid (6) the Wasatch domain deposits are composed of more than one genetic deposit type more often than deposits of the Basin and Range domain. Three additional conclusions with immediate economic significance are; (1) the median sand and gravel deposit in the Wasatch domain, 360,000 m3 (275,000 yd3), is three times larger than that of the Basin and Range domain (120,000 m3 [90,000 yd3]), (2) the median deposit thickness in the Wasatch domain, 5.8 m (19.0 ft), is nearly twice that of the Basin and Range domain (3 m [lo ft]), and (3) the Wasatch domain also contains slightly larger diameter gravel. These three conclusions are significant because the trend for sand and gravel development in the Bonneville Basin is to move from the Wasatch domain to the Basin and Range domain. Smaller, thinner deposits with smaller diameter gravel will require more surface area to mine than would have been necessary in the Wasatch domain. The result is a higher cost for sand and gravel in construction projects in the Salt Lake City area, especially since the gravel must also be hauled farther.

Jan 1, 2001

By J. M. Mutmansky, C. Lee

"This paper outlines some of the work associated with a research study into the relationship between the characteristics of coal mine dust and the incidence of coal workers' pneumoconiosis (CWP). The project involves study of the chemical, mineralogical, and morphological characteristics of the dust. Early stages of the study have dealt primarily with the size analysis and elemental composition of airborne dust in continuous miner sections. This paper outlines the procedures and findings of the elemental analysis portion of the study.Most of the previous elemental analyses of coal were made available in the quest for information on the combustibility of coal dust or on causal agents and prevalence of CWP. However, no extensive studies have been performed to date, primarily due to the limitations of the analytical methods. A review of the analytical methods for elemental characterization of coal and coal dust particles is presented. TI1e comparisons are made based on the sample mass required, the sample preparation required, the destructivity of the test, and the capability of providing an easy multi-element analysis. The reasons for selecting the proton-induced x-ray emission spectroscopy (PIXE) method are outlined.The PIXE method was applied to both the airborne coal mine dust and channel samples collected from seven continuous miner sections in six different mines. Channel samples of the coal, roof and floor were collected and analyzed. Airborne dust sampling was performed using multi-stage cascade impactors and permissible 2.0 I/min pumps. Sampler locations were fixed in the sections with respect to the continuous miner and roof bolter or with respect to the intake and return airways. Sampling times varied from 45 minutes to 6 hours, depending on the dust concentration.The statistical analysis of the resulting elemental data is presented. Of particular importance are the analyses of the variation of elemental composition with size and the variation in elemental composition over the working section. One interesting finding is outlined showing the multivariate statistical analysis of the trace elements and its implications in the identification of the dust sources. The paper concludes with an analysis of the ramifications of the elemental data to related medical studies."

Mar 1, 1989

By R. K. Steinhorst

Multivariate cluster analysis, MANOVA, canonical analysis, and discriminant analysis of hydrochemistry data were used to investigate the directions of ground water movement in basalts in the vicinity of the Hanford Reservation, Washington. The statistical analyses indicate that the hydrochemistry of the ground waters in these basalt formations is distinctly different on each side of the Columbia River. This suggests that the river is a ground water divide or that the river is roughly coincident with a hydrogeologic barrier boundary. The statistical procedures used in this study constitute a quantitative means for differentiating ground waters according to hydrochemistry.

Jan 1, 1990

By R. W. Brauchli

During the last few years the compila-tion of formation logs from rotary well cuttings has become common practice among petroleum geologists. This meth-od has undoubtedly furnished a great amount of information valuable for both scientific and commercial purposes. How-ever, in spite of its great usefulness it has certain drawbacks, principally in the contamination of cuttings by cavings. In extreme cases this contamination can reach such proportions that it is next to impossible to draw conclusions with any degree of certainty as to the nature of the formations penetrated by the drill. This difficulty was frequently encoun-tered during the development of the Okla-homa City Field. In many cases where Wilcox sand-the most prolific sand of this field-was drilled, the samples con-sisted almost entirely of shale cavings with only traces of sand. In order to obtain more reliable knowl-edge of the formations encountered while drilling it is therefore necessary to resort to more coring, and above all to improve our present methods of coring. With this in mind a study has been made of the results of coring in the Oklahoma City Field, and the present article is mainly confined to a statistical analysis of the relation between recovery, diameter of cores and drill pipe, length of cores and a few other factors. Most of the coring in the Oklahoma City Field was done during the early part of, the development. A total of around 18,000 feet or 0.3 per cent of the total footage drilled before February, 1932, has been cored, and about 80 per bent of the cores were taken in the Simpson formation at a depth below 6,000 feet.

Jan 1, 1933

By L. Xu, A. Vazirnegad, R. Bhaskar

"Respirable dust samples are collected by the U.S. Mine Safety and Health Administration (MSHA) and mine operators as part of the requirements of the Federal Coal Mine Health and Safety Act of 1969. About 1.85 million respirable dust samples collected by MSHA were analyzed for the period 197/ to 1990 f or the states of Alabama, Colorado, Illinois, Kentucky, Ohio, Pennsylvania, Utah, Virginia, and West Virginia. Trends in coal dust exposure of continuous miner operators, helpers, and roof bolters were analyzed. The reported production in each of the nine states was analyzed. The relationship between average dust exposure and coal production was evaluated. In addition, the differences between mine operator and MSHA inspector collected data were examined for each state. The average exposure levels for the three occupations - miner operator, miner helper, and roof bolter were also compared.The data indicate that the dust exposure levels have significantly dropped over the last twenty years, while at the same time production has increased, attesting to the ability of the U.S. mining industry to adapt successfully to the stringent dust control regulations. In terms of coal production, it appears that some states, such as Utah, Illinois, and Kentucky, were able to increase their production significantly relative to others, such as Pennsylvania and Virginia. The relationship between dust concentration and coal production is, at best, tenuous. 11 implies that existing dust control technology has assisted several mine operators to meet dust standards, while, at the same time, enabling mines to produce more coal than before. Comparison of data collected by MSHA and mine operators indicate that MSHA inspectors recorded higher dust levels and lower shift production relative to mine operators."

Jan 1, 1993

By A. C. Dorenfeld

CHANGES in circuits are often made in milling operations. At the same time that these changes are being evaluated the ores are changing. Even from the same mine, the ore is usually variable as to amount and type of mineral content, degree of association of valuable and gangue minerals, amount and types of soluble salts, hardness, etc. The question then arises whether any small differences in results, after changes have been made in the various circuits, are really due to these changes or whether the variability of the ore can account for those differences. Statistical evaluation provides one method of answering the question that arises so often in beneficiation studies: Did changed results come about because of changed process, or did ore variation cause the change? In this case, data were available for statistical analysis from an operating period of 42 months, representing treatment of approximately 1 million tons of ore. During this period there had been two flowsheet changes: 1) regrind of the zinc circuit middlings was introduced, and 2) alcohol- pine oil frother mixture was substituted for cresylic acid-pine oil frother mixture. Findings are in Table I.

Jan 10, 1954

By Sergio N. Monteiro

Lignocellulosic fibers obtained from plants like cotton, flax, hemp, sisal, jute and many others are natural materials used, since long time, in basic items such as textile, baskets, roofing and carpets. These traditional natural fibers as well as some new ones are nowadays replacing synthetic fibers as composite reinforcement owing to environmental advantages. The heterogeneous characteristic of lignocellulosic fibers is, however, a limitation for application in composites. The buriti fiber, extracted from a tropical plant tree, is recently being investigated as a possible reinforcement for polymeric matrix composites but no complete information exists regarding its mechanical behavior. The objective of this work was then to carry out a statistical analysis on the mechanical properties? uniformity of buriti fibers. By precise dimensional measurements in association with tensile tests, it was found that the mechanical properties depend on the range of the fibers? dimension.

Jan 1, 2009

By C. Flores, L. G. Twidwell, T. S. Jordan

It is well known that manguniferous silver ores containing manganese intimate) associated with silver are not amenable to conventional extraction methods. The segregation process has been applied primarily to the recovery of copper from oxidized and oxide-sulfide ores. A new alternative process, consisting of segregation roasting followed by flotation to recover the silver from refractory manganiferous silver ores, was studied using a 23-factorial experimental design. Laboratory investigations were conducted on a manganiferous silver ore analyzing 0.02% copper, 0.09% lead, 0.33% zinc, 12.55% manganese and 187 g/t silver. The investigation was designed to study the effects of the addition of salts, coke and copper (11) oxide on silver recovery. The results indicated that 79.3% of the silver can be recovered in the absence of copper oxide and 88.4% of the silver can be recovered with a copper oxide content of 1.5% at 750°C, 2% salt (NaCI). 1 % coke and 30 min of roasting. It was concluded that the addition of copper oxide improves silver recovery.

Jan 1, 1996

By Ross W. Smith, D. L. Taylor, K. A. Altman

Traditional sensitivity analysis of metallurgical data has the potential to overestimate the value of mining projects. Such analyses provide no information about the probability of the results. Simulations that rely on the input of statistical information provide more realistic predictions of the value of future projects and offer additional information regarding the probability of the outcome.

Jan 1, 2003

By C. A. Hunt

The problem of materials balancing is reviewed with particular reference to the minerals industry. A broad statistical framework is established that, besides extending the classical estimation problem, allows questions concerning the value of sample information to be addressed. The following are examples of such questions: How much money should be spent on sampling? Which streams in a plant should be sampled? What should be sampled? The approach adopted makes use of Bayesian analysis. The discussion includes an illustrative example involving a simple flotation circuit.

Jan 1, 1985

By K. Kim, T. M. Yegulalp

A new explanation of the scale dependency of rock strength is presented based on the theory of extremes. A brief review of past work on specimen size and strength relationship is followed by an introduction to the fundamentals of the underlying theory of extremes and its relationship to the scale effect. It is shown that the weakest link theory is directly related to extremal statistics and that parameters of strength distributions of rock can be derived as a function of the specimen size. Three sets of Brazilian test data are used to demonstrate the use of this approach.

Jan 1, 1994

By T. M. Yegulalp

A new explanation of the scale dependency of the strength properties of rock is presented based on the theory of extremes. A review of past work on specimen size strength relationship is followed by an introduction to the fundamentals of the underlying theory of extremes and its relationship to the scale effect on the statistical properties of the strength distribution. It is shown that the weakest link theory is directly related to extremal statistics and properties of strength distributions of rock can be derived as a function of the specimen size. Three sets of Brazilian test data are used to demonstrate the use of this approach.

Jan 1, 1992