Search Documents

By D. Madsen, B. Salamondra, A. Moss, D. Etienne

"Raise mining at the Namew Lake Nickel Mine in Manitoba uses 3 m diameter bored raises driven at 45 to 50 degrees dip for stope access and drilling. These raises are developed within the orebody on 20 m centres to accommodate electric-hydraulic longhole jumbos and charging wagons. Critical elements of stope development include delineation of are contacts, control of deviation during raise development, optimal stope sequencing to permit a high extraction rate, drill anchorage installation, production drilling and blasting, and ground control. Procedures to deal with these elements are described, with emphasis on the geotechnical investigation for design of open stopes and pillars.Although mining with drilled raises does not have the flexibility to follow large variations in orebody dip, results to date indicate that it can be used successfully in the thicker ore zones. Thinner zones are currently mined using a modified Avoca method. Some flexibility to accommodate variations in orebody dip in thin are zones may be obtained by using alimack raise climbers to drive access raises, and carry longhole drills and charging equipment. Rock quality has been sufficiently good to maintain stable stope walls for full-height mining of primary stapes at 20 m strike length.IntroductionThe Namew nickel deposit is located 60 km south of Flin Flon, Manitoba. It is a moderately dipping (45 to 50 degrees) pipe-like ultramafic intrusion with a sulphide halo enrichment. The diluted recoverable ore reserves at January I, 1990 are 2.2 million tonnes grading 2.05% Ni and 0.7% Cu. The operation is a joint venture between Hudson Bay Mining and Smelting (60%) and Outokornpu Mines Ltd. of Toronto (40%). The mine is budgeted to produce 530 000 tonnes in 1990. The deposit was discovered in 1984 and mine development commenced in 1987.In the raise mining area, primary stopes will be filled with a high quality backfill consisting of cement and quarried limestone. Secondary stopes will be mined out between the primaries in the second pass of mining. The design extraction rate is 94% over all.The orebody above 120 level has an average mining width of 2.4 m, so is too narrow for raise mining. A modified form of Avoca stoping is used."

Jan 1, 1991

A short study showing how first dry fill and later hydraulic sand fill has allowed mining to continue immediately adjacent to worked out areas in a mine 75 years old. This paper is a case study of filling in an old mine where for 30 years filling was not important until ground troubles were experienced after a series of parallel shrink stopes were pulled empty., Dry fill was distributed from the surface via a system of passes and conveyor belts. With the stabilization of the ground it then became possible to continue mining beside and above the old stopes using totally sealed and decanted hydraulic sand fill. A brief description of the dry fill is given and then more technical details of the hydraulic fill. The necessity for a well trained and experienced hydraulic fill crew is discussed along with the problems of filling small stopes in broken ground.

Jan 1, 1973

IN the irregularly shaped ore-bodies of the North Mount Lyell mine by overhead stoping, the method of filling the is a special feature.The situation of the mine two miles from the smelter and mill at an devation of 1000 ft. above the latter, precluded the economical use of granulated furnace or the mill tailings, even if these materials were as suitable for the purpose as the rock nowquarried at North Lyell methods at Mount Lyell have already been described in Proceedings of the Institute.*The breaking the ore in large dome-shaped stopes is still the rule, but the slope or "rill" is much flatter now than formerly. Owing the greater fluidity of the filling now in use, it is sometimes necessary to resort to square-sets, both at the ground floor and above, the roofs and walls are generally enough to permit stoping without timber, except for ground and occasional stacks on the rills.Sufficient area of ground floor has been beaten out to start overhead stoping, the dome back is partly formed, with its apex a rise which connects with the mullock-pass reticulation.(Sce 1 showing this reticulation in diagrammatic form.)

Jan 1, 1927

North Broken Hill Limited came into prominence as a producing mine at· the commencement of the present century, when a great many of the disabilities experienced in earlier mining operations th:rough lack of adequate stope filling had been overcome.The northern or narrower ore-body was first mined in the upper levels and, in the early stages, no great difficulty in mining was experienced. In depth, under the influence of its northerly pitch,. the wide southern ore-body entered the North mine between the 400 and 500-ft. levels. Owing to its flat dip and the relatively weak nature of the hanging wall and footwall, the value of close filling was recognized and this policy has been followed throughout the life of the mine. This feature undoubtedly contributed to the freedomfrom "creep" action to which some of the older mines had been subjected.The Broken Hill lead-zinc-silver ore-bodies occur as well defined replacements of favou:rable horizons, in intensely folded Pre-Cambrian sedimentaries. In the North mine two main replacement zones occur, the Gre being found where the beds are involved in a certain set of minor folds. The resulting ore-bodies are roughly elliptical in cross-section, the long axis of one being north-east of, and somewhat offset from the long axis of the other. The ore-bodies pitch eastwards at 40° and dip northwards at 60° in a fairly regularmanner. The southern Ore-body has an average length of 700 feet and an average width of 90 feet with a maximum width of 230 feet, whilst the nonhern ore-body on the lower levels averages 500 feet long and 40 feet wide.

Jan 1, 1940

By James D. Hall

THIS essay deals with the materials and methods used in the waste filling of scopes in Canadian mines, with especial reference co the methods used at the Sullivan mine, Kimberley, B.C. The author would like to thank members of the staff of the Sullivan mine for information obtained, and acknowledges material from the following publications: Waste Filling of Stopes: Information Circular 6816, U.S. Bureau of Mines. Mining Methods and Practices at Lake Shore, by Leslie S. Weldon; Trans., C.I.M. & M., Vol. XXXIX, 1936, pp. 142-202. Development and Mining (at the Mcintyre Mine), by D. E. Keeley; Eng. & Min. Journal, November, 1933. INTRODUCTION Although mining in Canada is a relatively youthful industry, many of our mines have reached a stage of extraction which requires waste filling, both as a means of support and co make possible the winning of ore that would otherwise have co be left in the mine. Fill may be used at regular intervals as one of the cycle of operations, as in cur-and-fill and square-set scoping; or it may be introduced into a completed stope co provide permanent support for overlying rock formations, and co permit mining of pillars of valuable ore. Waste fill is sorted in resuing, which is a form of cut-and-fill scoping employed in narrow veins.

Jan 1, 1937

By Yates C, Gillie E. W, Finucane K. J

During the year 1940 a complete investigation was made of the whole of the stoping operations throughout the Great Boulder Mine and, as a result, it was decided to convert some of the existing shrinkage stopes into cut-and-fill stopes, and also to mine many of the more recently developed ore blocks by the latter method. The necessity for filling was due primarily to the structure of the ore blocks, the character of the walls and possible excessive dilution, but was influenced also by the grade of the ore-block and by the fact that cleaner mining can be carried out by cut-and-fill stoping.The comparatively few cut-and-fill stopes in operation prior to 1940 had been filled mainly with waste rock from development work, but as the amount of this material available, or likely to become available, would have been wholly inadequate for future operations, it was proposed to construct a system of passes to supply filling material from the surface.Owing to the distribution of the stopes, no central pass or system of passes could be devised which would service all the stopes satisfactorily.However, work was commenced on two passes, one designed to service the cut-and-fill stopes in the Eastern Section of the mine, and another to service those in the Western Section. It was realised that these passes could serve only a small proportion of the total number of Stopes (Figs. 1 and 2). During the progress of this work experiments were undertaken to test the possibility of using filtered tailings underground as an adjunct to the above scheme, but for various reasons these were only partially completed.Early in 1942 it was suggested by the Mill Superintendent that an attempt be made to fill with wet classified flotation tailings as practised at Mt. Lyell in Tasmania and at the Triton Mine at Reedy, West Australia. For the purpose of testing this, an experimental stope was prepared on the 309-ft. level, "X" Lode. This was 100 feet long and averaged 4 feet in width. Water-tight rearings were built at each end of the stope and waste rock fill was spread to a height of 6 to 8 feet above the timber. Used filter cloths were laid on top of the fill and brought a few feet, up the walls of the stope. A two-inch victaulic drainage line was then placed in position, the end passing through a hole in one of the bearings and thence to a sump. In the central portion of the stope two vertical pipes were brought up from this line. These were bored with one-inch holes staggered on opposite sides of the pipe, the vertical interval between each hole being one inch. The holes were then stopped with...

Jan 1, 1945

Stope filling practice on the Great Boulder Mine was described in -a paper published in Aus.I.M.M., Proceedings No. 137, in 1945. When the paper was presented the process had emerged from the experimental stage, most of the initial operating difficulties had been overcome, and it had been established that this method of filling was suitable for the working of ore bodies in the Kalgoorlie field: Since 1945, it has fulfilled its early promise, -and during 1947, the tonnage of fill placed was sufficient to cover current operating requirements as called for by the mine ore breaking programme. The object of this paper is to outline current operations. In so doing it will refer' to some ground covered by the previous paper, but will omit details of the initial experimental work. It will include, however, a description of further experimental work on the use of hydraulic filling for worked-out shrinkage stopes, arid will provide more accurate data on costs than were available previously.ESTIMATE OF TONNAGE OF FILL REQUIRED.Early in 1946, the mine ore reserves were analysed in order to estimate the relative tonnages to be mined per four-weekly period by shrinkage stope methods -and by cut and fill stope methods respectively. This analysis was extended beyond the blocks already prepared for stoping, and inclqded the majority of the major ore blocks in the mine ore reserves. It gave the following results:-For a mill tonnage of 28,000 tons per period, 6,933 tons were required from cut and fill stopes, and a possible future maximum programme of 35,000 tons per period would require...

Jan 1, 1948

By AIME AIME

THE two illustrations below, furnished through the courtesy of J. P. Messervey, Deputy Inspector of Mines, Department of Public Works and Mines, Province of Nova Scotia, show a fourth-level stope in the salt mine at Malagash, N. S. Fig. I was taken when the stope was begun, and Fig. 2 shows how it looked two months later, the photographs being taken from the came point. This stope is at a depth of about 300 ft. and is on the MacKay seam, which is the central band of white salt running through the Malagarh deposit. As run be seen. the vein is vertical. and varies from a foot to 50 ft. in thickness. The

Jan 1, 1932

By B Hall

In feasibility studies the choice of optimum cut-off grade is typically based on an evaluation of tonnage grade curves and manual design of stopes at one or two cut-off grades. In the industry these stope designs are usually based on break-even cut-off grades, but there is little consensus on what cost and price assumptions ought to be included. A new tool for automated stope design has been developed that generates sets of stope shapes for a nominated range of cut-off grades, or depending on the nature of the mineralisation, cut-off values based on net smelter return calculations in the block model. The stope design procedure includes constraints in stope and pillar geometry for the selected mining method and can be used to evaluate sublevel interval and sensitivities to other design parameters in the specific geological and geotechnical environment. These ænested stopesÆ are analogous to ænested pitsÆ in open cut design, and can be used as a key input in the æhill of valueÆ methodology for the evaluation of the optimum cut-off grade in underground design. The results of many consulting studies indicate that a break-even cut-off grade will not be the optimum cut-off grade. A particular benefit of the new stope design tool is that the design rules used to establish stope shapes in the feasibility study can then be used in mine production, in an optimal and repeatable method. This methodology is being advanced in the AMIRA P884 PRIMO project, which is a new research collaboration coordinated by AMIRA International. The project has brought together active research groups in Australia and Canada, with the goal of developing a flexible framework and set of software tools for optimisation in underground mine design.

Jan 1, 2009

By M J. Pascoe

The performance of 460 stope surfaces at WMC ResourcesÆ Olympic Dam Operation (ODO) has been used to investigate the confidence that can be placed in the Stability Graph Method for design of stope dimensions. A detailed database of stope performance and ground condition information was established for each stope. The database contains all the required stability graph information as well as other factors thought to influence stability, such as discrete major structures, poor shape and exposure time. The performance of each stope surface was quantified by calculating Equivalent Linear Overbreak/Slough (ELOS). The performance of stope walls and crowns was plotted on the supported and unsupported case history stability graphs. Based on this information an ODO design limit of HR = 3.3 x NÆ0.33 has been suggested for stope walls. Walls that plotted above this line were 80 per cent stable, 20 per cent unstable and zero per cent failed. Below the line 60 per cent were stable, 30 per cent unstable and ten per cent failed. Supported crowns that are flat or arched in shape and are not within the influence of major structures can be designed in the stability graphÆs æstable zoneÆ with a strong likelihood of stability. The Stability Graph Method did not reliably predict the performance of unsupported crowns at ODO.

Jan 1, 2005

Throughout the study phases (scoping, prefeasibility and feasibility) of new mining projects one is forced to work with and make predictions based upon limited date obtained from diamond and reverse circulation drill holes. These data are extrapolated to determine how much of the valuable metal is present in the ground, how it can be recovered it and the efficiency of this recovery. Mining methods to extract the ore are investigated with forecasts made regarding excavation stoping stability and performance in an attempt to optimise production. Extraction and use of rock mass data for use in characterising the mechanical behaviour of the rock mass is no exception. One often relies heavily upon the use of empirical charts developed over many years on hundreds of case histories based upon rock mass characterisation schemes. This is largely successful and indicative of what one might expect. However specific site characteristics can always play a significant role, and are not necessarily apparent in diamond drill core. Feasibility studies for the Favona orebodies indicated that the rock mass was generally poor to extremely poor, and that stoping conditions would be difficult in all of the orebodies for various reasons. A range stope performances were achieved ranging from very good to very poor and in some cases unexpected results were achieved. A comparison is made between what was actually achieved and what was expected since stoping commenced in 2007. Explanations are attempted for differences in stoping performance and, in some cases, unexpected results at the Favona underground mine are attempted.

Nov 25, 2010

By S. Evans, J. Phillips-White, D. Morton

The partnership between Orica and MMG at the Dugald River Zinc mine in Australia has led to the first global field trials and deployment of Orica’s Subtek™ 4D™ (hereafter referred to as 4D) Bulk Systems underground bulk emulsion blasting technology. This technology offers advantages over conventional bulk explosives by extending the range of energy and length of explosive column that can be charged in underground production. 4D gives blast designers energy options between Relative Bulk Strength (RBS) 50 - 150, delivered uniformly along the entire column in most blasthole conditions along with the ability to instantaneously modify the energy within an individual blasthole. During Phases 1 – 3 of the project from October 2022 to January 2023, over 57 tonnes of the 4D Underground emulsion were loaded in 17 stopes. The primary objectives of this phase were to reduce hanging wall dilution and improve stope recovery. While drilling and other parameters remained unchanged, the energy selection was tailored for specific situations, guided by a revision to the site's drill and blast standard. The design used low energy (RBS 50 - 70) in holes adjacent to the hanging wall and high energy (RBS 130 - 150) where stope recovery had historically been challenging, such as at the toes of long downholes. Initial results of the project focused on five stopes selected for their similarity to those used for the baseline data set. Although the 4D data set was small, the post-blast scans indicated favourable results for recovery and dilution. This suggests that selecting and delivering bulk explosive with tailored energy levels can improve stope performance.

Jan 1, 2024

By André van Wageningen

Long term mine scheduling is one of the most difficult optimization problems. The problem is said to be NP-complete in that the best possible solution cannot be found any quicker than checking all possible permutations and combinations. In current mining operations, it is important to report changes in long term plans as soon and as accurately as possible. Where geological data can change rapidly, such as in narrow vein deposits, the need to quickly identify and optimize different long term alternatives becomes a difficult task and can lead to many permutations of the long term mine plan. The question arises, is the new plan optimal or not? Can the company objectives be met while adhering to operational constraints? Although a number of optimization techniques have been used in the past, many include significant simplifications or fail to produce acceptable results within the required timeframe. Genetic Algorithms (GAs) are among the most promising optimization techniques within operations research. They are based on natural selection and evolution of solutions to complex problems. They have been known to quickly converge within a few percent of the optimal solution by examining only a fraction of the possible permutations. The GA itself contains very little problem specific information and, as such, in this study, has been linked to a discrete-event simulation (DES). The DES is able to evaluate each sequence proposed by the GA and determine the effectiveness and value of each schedule. The DES feeds information regarding the feasibility and quality of the solutions back to the GA during the optimization process. In this paper, GAs and DES are described and the coupling of the two methods is outlined. The GADES module is then used to ?optimize? a narrow vein theoretical case study and the results discussed in a broader mining context.

Oct 1, 2004

By Mustafa Kumral, Yuksel Asli Sari

Economic evaluations of underground mining operations are made based on the estimated or simulated grades of the block model as the actual values are not known. Depending on how the planning decisions are made, the risk of the operation can be managed and decreased. This research introduces a mixed-integer linear programming (MILP) model for stope sequencing optimization that considers the uncertainty associated with net present value (NPV) using chance-constrained programming (CCP). The introduced method permits achieving a balance between maximizing NPV and reducing the associated operational risk through transforming the problem into a multiobjective problem, where the objectives are maximizing the NPV and minimizing the risk. This risk is expressed in terms of the standard deviation of project outcomes, taking into account multiple possible scenarios. In a case study, the efficiency of the method was demonstrated as a decision-making tool capable of translating a specified risk or reliability level into a stope sequencing plan.

Jan 1, 2024

By Mustafa Kumral, Yuksel Asli Sari

Underground mining operations are sensitive to price fluctuations because they usually perform with a narrow profit margin compared to open-pit mining. Furthermore, the economic evaluations regarding operation are based on estimated or simulated grades rather than actual values. These bring a high degree of uncertainty to the viability of an operation. Hence, mine planning that accounts for uncertainty is crucial for underground mining operations. As an underground mining technique, sublevel stoping has geotechnical, curing time, seismicity, cost minimization, and production requirements. A new mixedinteger linear program is proposed that considers the uncertainty associated with net present value using chance-constrained programming. The net present value (NPV) maximization objective is transformed into a multi-objective maximization problem where one objective is to maximize the mean NPV, and the other objective is to maximize the negative standard deviation multiplied by a scalar called risk or reliability level. The balance between the two objectives was maintained by this scalar and was selected based on the reliability level of the project. A case study was conducted with varying reliability levels, and sequences were generated. It was shown that the expected net present value increased at higher reliability levels, and the overall value of the objective function decreased as the reliability level increased. In other words, the variance component penalized the value of the objective function. Moreover, it was observed from the case study that at lower reliability levels, stope grade order bears similarity to the extraction order.

Aug 4, 2023

By G de Jong, W Sunyoto, K Sari, P Silalahi

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Big Gossan mine is operated by PT Freeport Indonesia and is one of the largest stope-and-fill mining systems in the world. The Big Gossan deposit is a ~200 m wide, 1200 m long and 500 m high steeply north-east-dipping to subvertical skarn body at the Cretaceous-Tertiary Ekmai-Waripi contact. The copper-gold mineralisation, with a 1.3 per cent copper equivalent cut-off grade, occurs mainly proximal to the Ekmai-Waripi contact in the garnet-clinopyroxene prograde skarn at the base of the Tertiary Waripi formation and partly distal to the contact in the tremolite-actinolite retrograde skarn of the Tertiary Waripi formation.The Big Gossan stope mine is designed from 2540 m to 3020 m above sea level. Present active stoping operations occur at level 2540 mL to level 2640 mL and are done in a primary and secondary stoping sequence. The width and length of the stopes is 15 m and 20 m respectively, while the height of the stope varies between 20 m and 40 m, depending on the ground conditions. The stability of the stopes is visualised in the Mathew’s Stope Stability graphs. These graphs and actual Cavity Measurement Scanner measurements on the stope will predict and show the overbreak and underbreak, which affect the reconciliation of the mined stope and also the pillar stability between the primary stopes. Geological factors like major structures, joints, veins and alteration intensity are important factors that correlated with the stability of the Big Gossan stopes.CITATION:Sari, K, de Jong, G, Silalahi, P and Sunyoto, W, 2015. Stope stability at the Big Gossan skarn deposit, Papua, Indonesia, in Proceedings PACRIM 2015 Congress, pp 139–146 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Patrick Frenette

The Goldex Mine is an underground gold mine using a unique mining method where a single very large stope is being created. In order to maintain stability of the walls and roof of the stope which is 450m, 250m high and up to 120m thick, ore is left in the stope as long as possible and acts as backfill would do. At many occasions during the mining sequence, the walls will be exposed on height ranging from 30 meters up to 250 meters. A monitoring system comprising in-stope laser surveys, a seismic system and an array of extensometers and sloughmeters all remotely connected to surface is used to observe the shape and evolution of the stope. This paper will focus on the results obtained following some of the large blasts and on the long term monitoring of the stope.

May 1, 2011

By D. G. F. Hedley, F. Grant

"In 1958, the Ontario Department of Mines appointed a committee to study the accident situation and mining methods used in the uranium mines in the E1liot Lake district. This committee reviewed the existing knowledge on mine design, pillar support and roof spans and came to the conclusion that scientific knowledge had not yet reached the stage of producing rational design procedures which would reduce the dependence on trial-and-error methods. Since that time, the Mining Research Centre has made numerous stress measurements in two mines to define the pre-mining and pillar stresses. A comprehensive series of tests has been done in the laboratory to measure the compressive strength of the rock; a geological survey of the region has been made to evaluate tectonic stresses; and a survey was done on mining conditions with regard to stable and unstable pillar configurations. This information has been used to evaluate pillar design as effected by pillar width and height, depth below surface, extraction and pre-mining stress fields. The resultant design of pillar widths and corresponding extraction as the depth increased is in line with past and present experience in these mines. The information available on roof stability is still insufficient to design stable stope spans with the same degree of confidence; experience and trial-and-error methods are still required."

Jan 1, 1972

By R. H. English, N. C. Joughin

The results of trials with three stope-face cleaning systems are described. Two of these systems were based on armoured chain conveyors, and the third on a reciprocating-flight conveyor. The operational elements of each system are discussed with reference to their effectiveness, and many problems are highlighted. It is concluded that the reciprocating-flight conveyor is superior, and has the potential for being developed into a system yielding a labour productivity of more than 30 m2 per worker per month and a face advance of 15 m per month working one shift a day.

Jan 1, 1979

By Coulter L. J

THE method of stope surveying as practised at the Mount Lyell Company's mines has been evolved out of the exigencies created by special conditions. It presents some novel features, and has proved effective for all requirements. All stope measurement work is brought under one complete system, to which office methods are standardized. Before proceeding to deal with the subject a brief description of the physical characteristics of the ore-bodies of each mine and the method of stoping will serve to show, cause ,for departure from ordinary survey practice.NORTH LYELL MINEThe ore-bodies of this mine occur on or near the conglomerate schist contact, and, being probably the result of replacements of both rocks, they rarely present any definite walls. It is usual for the payable material to merge into the respective countryrocks, and the limit of the occurrence is defined rather by assay value than by any distinct natural boundaries. The general configuration of these ore-bodies, therefore, is highly erratic both in horizontal and vertical section, so that, in order to obtain an accurate record of any occurrence, the measurement of the actual contour at short vertical intervals is essential.Stoping is carried out on a modification of the "rill." system, perhaps more properly described as "arched back" or "dome" stoping. Mullock rises are placed in as convenient positions as the erratic configuration of each ore-body will allow, and aroundthese rises the back is kept well arched, both longitudinally and transversely. The larger stopes are divided into arbitrary sections in which ore-breaking and mullocking are carried out in rotation, so that the whole of the excavation is seldom open for measuring at anyone particular time. Stacking or square-setting on the...

Jan 1, 1915