Search Documents

By Dongjie Zhang, Shuxin Liu, Jianduo Wang

Broken rock mass and unreasonable stope structure parameters can cause excessive ore loss and dilution in sublevel caving; this is the main problem faced by caving mining in recent years. This paper proposes a stope structure parameter optimization method suitable for steeply inclined medium-thick broken ore bodies and evaluates the reliability and effectiveness through case studies. To solve the problem of large ore loss and dilution in the high-end wall sublevel caving method of Xilinhot fluorite mine, it is necessary to select proper stope structure parameters. Based on the theory of random media, an end-wall ore drawing experiment was carried out, and the bulk flow parameters needed to optimization of stope structure parameters were determined. In the experiment, it was found the draw-out body of high-end wall ore drawing showed a fine top and a thick bottom; the granular media had good fluidity. The reasonable caving step is determined to be 1.2 m instead of the 1.6 m originally used. Through the optimization experiment of the mining route position along the vein, the study found that the best route position is different with the ore body inclination. When the inclination angle of the ore body was 90°, the reasonable route was located in the center of the ore body. When the inclination angle of the ore body was between 85° and 90°, the route moved from the center of the ore body to the footwall at a rate of 22.5%. When the inclination angle of the ore body was between 80° and 85°, the route moved to the footwall at a rate of 54.8%. When the inclination angle of the ore body is not greater than 80°, the route should be arranged on the boundary of the footwall. Field application results showed the dilution rate reduced by 7.66% and the recovery rate increased by 7.31%. Field test results verify the effectiveness and applicability of the optimized stope structure, which corroborates the effectiveness and applicability of the optimized stope structure.

Mar 10, 2022

By Wang Yingmin, Xu Zhuyun

The optimum of general mine ventilation networks is very difficult and has a considerable significance. Based on the content model, this paper presents a more general nonlinear programming model whose number of variables equals that of independent meshes. The constrained conditions are linear inequalities only. The model is changed into an unconstrained problem with multiper method. The optimum results are computed with DFP algorithm and the Improved Golden section method is used in its linear searching. The computer program written in Quick BASIC is suitable to the optimum of any type of large mine ventilation networks with different regulating devices. The paper presents two examples for optimum of ventilation networks.

Jan 1, 1991

By Liu Fan, Shang Yanbo, Wang Zhongming

"Besides valuable metals of Cu, Sn, WO3, Zn, there are S, Ag, CaF2, In and so on in a complex ore deposit in south China (which belongs to Hu Nan Shizhuyuan Non-ferrous Metal Limited Liability). Although it proved reserve amounts to 3.5×107 ton, its crystal character limits its utilization in large-scale. It features complex relationships between valuable minerals, finest crystallized particle size, low-graded valuable metals (Cu 0.30%, Zn 0.5-0.7%, Sn 0.2%, W<0.1%). If only tungsten minerals are considered, it means WO3 grade is too low (the cut-off grade of WO3 is 0.1% in China). Only Cu and Sn minerals are recovered from 2006 and Cu recovery is less than 70%, Sn 15-20%. Other valuable metals of W, Zn, S and CaF2 were lost in the tailings. To make good use of the ore, the technology of fully recovering Cu, Sn, W, Zn, CaF2 and rare metals are in urgent need. After systematic researches, the flow sheet of "bulk flotation of Cu-Zn minerals at first, then Cu-Zn separation, then recovering sulphide by flotation, then recovering iron minerals by magnetic separation, then bulk flotation of Sn-W minerals after desliming" is developed. Furthermore, specific Sn-W collectors of BK411 and BK412 are applied into the processes and better indexes are obtained. The industrial indexes are listed as followings: the content of Cu, Zn, Sn, WO3 of ROM ore is 0.31%, 0.65%, 0.13%, 0.03%; Cu and Zn recovery are 82.23% and 37.79% respectively; 63.76% of Sn and 34.34% of WO3 go into the Sn-W bulk concentrates. Economic benefits are remarkable."

Jan 1, 2014

By HONGWEI YANG, Lili Zhang

The oxidation behavior of copper smelting slag under non-isothermal conditions was studied by thermal analysis. The results indicate that the copper slag is mainly composed of fayalite ( Fe2SiO4) and magnetite ( Fe3O4). The oxidation behavior can be divided into two reaction stages with the increase in temperature; the first stage is the oxidation of fayalite to magnetite, and the second stage is the oxidation of magnetite to hematite. The two reaction stages cannot be strictly separated; that is, the reaction of fayalite is not complete, and magnetite has begun to transform into hematite. Based on the TG (thermogravimetric) curves, the ABS (Achar–Brindley–Sharp–Wendworth) differential and the Coats–Redfern integral methods were employed to investigate the oxidation kinetics of copper slag during the continuous heating process. The oxidation of fayalite into magnetite and amorphous silica phases occurs mainly in the temperature range of 673 to 1083 K. The activation energies calculated by the two methods are 193.69 and 195.52 kJ mol− 1, respectively. The reaction is consistent with Avrami–Erofeev equation, and the mechanism of oxidation is random nucleation and growth. The oxidation of magnetite to hematite occurs at 1083–1303 K. The activation energies are 308.79 and 328.77 kJ mol− 1, respectively. The mechanism conforms to the Jander equation and is controlled by the two-dimensional diffusion.

May 16, 2022

By HONGWEI YANG, Lili Zhang

Copper slag is mainly used in cutting tools, abrasives, asphalt pavement, road construction, and in the production of concrete as an alternative to sand and cement [1]. As a renewable resource, only about 15-20 percent of the slag is used for these applications, and the dumping or disposal of surplus unused slag results in waste of a certain amount of usable metal in the feedstock [2]. In this work, the oxidation behavior of copper smelting slag under nonisothermal condition is studied using data obtained by the thermogravimetric (TG) method, and the kinetics parameters and reaction mechanism of oxidation are determined. It provides a theoretical basis for the comprehensive recovery of iron resources in slag and the selection of reasonable slag-making conditions.

Oct 1, 2022

By Z Lianbi, Z Yibin, Z Youhong, P Bin

Without adequate soil available, it is difficult to rehabilitate a large area of acid mine waste dump with sustainable plant communities, which has a strong potential acid generation. In the present project, paste tailings capping method has been put forward to reconstruct plant ecosystem on acid mine waste rock dump. This rehabilitation method uses paste tailings as capillary break and plant growth media. The tailings used contained 26.3 per cent of particles of less than 20 ¦m which satisfy the requirement of grain of paste tailings preparation. The tailings are not acid- producing materials. In addition to Cu, total contents of Zn, Pb, Cr, Cd, As and Ni in tailings are lower than those in local soil. Paste tailings concentration 70 per cent ~ 72 per cent was prepared by concentrating ten per cent tailings by using polypropylenecrylic sodium as flocculation. The potential pollution risks are low by using paste tailings as capillary break layer. Plants directly grown in the tailings did not particularly accumulate Cu, Zn, Pb, Cr, Cd, As, Ni in roots, stem and leaves, which were 0.01 ~ 1.6 times of those grown in soil.CITATION:Yibin, Z, Lianbi, Z, Bin, P and Youhong, Z, 2012. Study on paste tailings capping ecology reclamation on acid mine waste rock dump, in Proceedings Life-of-Mine 2012 , pp 243-246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

As opposed to a prescriptive-based design, a performance-based fire-protection system design allows the system planner the flexibility in choosing specific method, materials and design tools to achieve a preset goal. A different approach in fire protection and a powerful addition to existing method, the system has been around for many years, and has gone through numerous improvements. Despite its popularity in the building industry, it has not been introduced to the mining industry yet. As mines get deeper, increases in size and complication, mine fire safety system will also become increasingly challenging, a new and proven system should be able to great potential to eradicate many of the problems that are either unsolvable or cost-prohibitive with the traditional method. With increasing globalization and international exchange with other major mining countries a common language/practice also make the performance-based design method a desirable feature in mine fire safety system. This paper will first define a performance-based system, step-by-step design methods, likely impacts on fire-protection practices and possible challenges in implementing the system in US underground mines.

Jan 1, 2011

By Chang-hong Peng

Solubility phase equilibrium in the ternary system of Me2+-NH4+-SO42--H2O (Me2+ represented Mn2+, Zn2+ and Fe2+) was studied by the isothermal method at 298K and physicochemical properties of the saturated solution such as density, refractive index and pH were also investigated. The experimental results show that the solubility isothermal phase diagrams of these systems consist of three invariant branches, two invariant points and three crystallization fields. Corresponding to the three crystallization fields, there have three phases of solid, that is MeSO4?nH2O, (NH4)2SO4 and (NH4)2Me(SO4)2?6H2O, respectively. At the eutectic point, the concentration and the refractive indexes of the saturated solution change evidently. Otherwise, the pH value change slowly in all the systems. The calculated results of the density and refractive index agree with the experimental results.

Jan 1, 2006

By Zhou Shu-cai

"A method has been proposed for the pre-treatment of high phosphorus iron ore by carbothermic reduction assisted with microwave irradiation and magnetic separation on a laboratory scale. Chemical analysis of the reduced ore sample, the metal sample and the slag sample were conducted. Based on the above research, the influences of carbon addition, microwave power and microwave irradiation time on the recovery of Fe and dephosphorization were discussed. It indicated that the increase of microwave irradiation time and power had substantial effect on the recovery of Fe while the influence of carbon addition was not obvious and the highest iron recovery ratio reaches some 95.5% when the dephosphorization ratio was 37.68%. A high iron recovery ratio and a reasonable dephosphorization rate were incompatible under the conditions investigated in this study due to the reduced iron and because unreduced P-contained gangues were not efficiently separated. This method may provide a reference for the future utilisation of high-phosphorus iron ore.IntroductionWith the rapid growth of crude steel production in China, the source of iron ore tends to become increasingly strained and is facing the risks of raw material shortage for the iron and steel industry. In order to decrease the production cost, China has to focus on the utilization of its domestic low grade iron ores for the iron and steel plants [1-2]. China has a large deposit of high phosphorous iron ore with a reserve of 7.45 billion tons which is unused in any large scale [3]. Therefore, the development of a successful and economically viable technology for high phosphorus iron ore is of profound importance. To remove phosphorus from the high phosphorus iron ore, several mineral and metallurgical processes have been proposed, such as bio-leaching [4], roasting reduction plus melting separation [5], pre-reduction and screening methods combined with mechanical crushing or air jet milling[6] selective agglomeration plus reverse flotation [7]. However these processes are not cost effective or are time consuming. The traditional pyrometallurgical process( BF+ BOF) refuse this kind of ore mainly because that molten iron is saturated with carbon or high carbon content and thus all phosphor us in the burden goes to the molten iron[8]. Therefore, it is important to exploit the cheap and abundant high phosphorus iron ore as a resource in ironmaking. In recent years, the microwave was widely introduced as a heat resource for extractive metallurgy of iron ore or other minerals. For example, microwave assisted ore milling, microwave assisted carbothermic reduction of metal oxides and microwave assisted mineral leaching issues[9-10]"

Jan 1, 2014

By W. Guiye, L. Chongjun, L. Huinan, Z. Yangge, H. Long

The current application of copper-molybdenum (Cu-Mo) separation inhibitors is often associated with large dosage, high toxicity, environmental pollution problems. In order to solve these problems, a light sensitive Cu-Mo separation inhibitor LS（light sensitive inhibitor，abbreviated to LS） was developed. In this paper, inhibitory performance, photodegradation rule, and acting mechanism of LS were studied. The subsequent test results showed that, compared with traditional inhibitors, LS has shown comparative advantages, with lower dosage and good inhibiting effect. A series of flotation tests with LS as inhibitor were conducted on a Cu-Mo concentrate. A locked-cycle test showed that a molybdenum concentrate containing Mo 49.88% and Cu 0.6%, with 93.23% molybdenum recovery and a copper concentrate containing Cu 29.92%, with 99.99% copper recovery can be obtained. The photodegradation performance of the reagent was investigated under 365 nm, 254 nm and sunlight irradiation. The degradation of the reagents could be completely achieved by irradiation of three wavelengths of light. However, with the different wavelength of irradiation light, the degradation rate is different, the time required to reach 50% degradation rate being 3 h (254nm), 4 h (solar light) and 6 h (365nm) respectively. The inhibition mechanism on chalcopyrite was studied. FTIR study showed that LS could be adsorbed on the surface of chalcopyrite by chemical adsorption, which could enhance the hydrophilicity of chalcopyrite. Ultraviolet adsorption tests indicated that the adsorption capacity of LS on chalcopyrite surface was greatly affected by pulp pH value, and the proper pH value was 5-9. Keywords: Copper-molybdenum separation, Inhibitor, Light-sensitive, Photodegradation, Mechanism.

Jan 1, 2020

By Chi Zhang, Junyi Wu

"With the increasing popularity of lithium cobalt oxide in lithium ion battery industry, which is driven by new energy vehicle and mobile device applications, the demand of cobalt is also growing rapidly in recent years. There is a significant trend of increasing investment on cobalt capacity in China, and the automation renovation is considered as an option of improving production efficiency. This study aimed at evaluating the practicability of stainless permanent cathode blank and automatic stripping process in cobalt electrowinning process. The purpose is to replace the old starter sheet process in cobalt electrowinning, which so far was used by most of cobalt refineries in China, but very labor intensive and exposed operators to serious aerosols that contained both cobalt and acid. In the old starter sheet process, the initial cobalt starter sheet is produced onto a plate made of titanium, while the titanium cathode blank and hanger bar fit the critical corrosive environment but is lack of mechanical strength for automatic production which has been mature in copper electrowinning process. To evaluate the proper materials instead of titanium, the coupon corrosion tests with different raw materials including 316L and other stainless steel grades were held for several months in production environment at a cobalt tank house in China. Following the comparison between titanium and other tested materials, a pilot production test in a cobalt tank house is also on-going.INTRODUCTION Cobalt has been known in early China and used in pottery glazes, and the ancient Greeks and Romans used its compounds to make colored glass since long time ago. The blue on the colored porcelain from the Tang Dynasty in China was also due to the presence of cobalt compounds. The word cobalt is known being derived from the German kobalt, from kobold meaning ""goblin"", because the cobalt-bearing blue ore, CoAsS, was called kobaltin in Europe in the Middle Ages, it may have been thought to be harmful to the health of the miners because of arsenic in the ores."

Jan 1, 2018

By Pei-xiao Liu, Han-jie Guo, Yan-xiang Li

The thermodynamic analysis on chromium ore pellets in solid reduction chromium process is carried out, and the result is validated by pre-reduction experiment of cold briquetted chromium ore. Polarization Microscope and SEM are employed to observe microstructure and element composition. The thermodynamic and experimental results reveal the reduction mechanisms at different temperatures in the SRC pre-reduction process.

Mar 1, 2017

Study on Preparation and Gel Performance of High Purity Montmorillonite In order to research the colloidal and thixotropic performance of the inorganic gel prepared by high purity montmorillonite, this study uses the moderate grade bentonite ores from Weifang (China) as raw material. Two-stage hydrocyclone classification was applied to obtain the high purity montmorillonite with its content of 94.8 per cent. In contrast to other methods of montmorillonite purification, two-stage purification by hydroclone has the advantages of larger throughput and easily achieving auto-control in industry, and purified products with different montmorillonite content can be obtained by this method. And then the inorganic gel was prepared by the prepared high purity montmorillonite and its colloidal and thixotropic performances by measuring the flowability and thixotropy were further studies. Research results show that the inorganic gel has plastic body liquidity, the viscosity decreases with the increase of the shear rate, the static and dynamic shearing stress values are 33.98&nbsp;Pa and 91.89&nbsp;Pa, respectively, and the thixotropic value is 95.2&nbsp;dyne+s/cm2, which indicates that it has preferable colloidal and thixotropic performance. Montmorillonite inorganic gel prepared by bentonite with high montmorillonite content and low-layer charge has better gel performance.

Sep 13, 2010

By Li Chongyang, Liu Baolan, Jia Xiaolin, Li Suping

An Al/Al2O3 gradient coating applied on a heat-resistant stainless steel was prepared through a slurry process by using aluminum and ?-Al2O3 powders as the transition filler material, alpha alumina as the surface coating material, aluminum dihydrogen phosphate as the binder, and sodium molybdate as the corrosion inhibitor. The effects of heat treatment temperature, adhesive/filler ratio and ?-Al2O3 content on the bonding strength, microhardness and thermal shock resistance were investigated. The crystal phase and microstructure were characterized by XRD and SEM. The results indicated that the composition of the coating changed continuously from surface to coating-substrate interface. The coating could offer high bonding strength and good thermal shock resistance when heat treated at 700°C.

Jan 1, 2010

By Shenghui Guo, Jianbo Lan, Hongying Xia, Jinhui Peng, Lihua Zhang, Libo Zhang

Spent Hawaii nut shell was converted into a high-quality activated carbon via steam physical activation. Analysis of the experiment including activation temperature, activation duration, steam flow rate on the adsorption capability and yield of activated carbon were identified. Response surface methodology showed that the activation temperature was identified as 866 , an activation duration of 36 min and a steam flow rate of 2.5mL/min with the methylene blue adsorption number of 195 mg/g and yield of 77.75%. The key parameters that characterize quality of the activated carbon such as the BET surface area, total pore volume and average pore diameter were estimated to be 1125m2 /g, 0.94mL/g and 5.21 nm, respectively. Additionally, by the SEM analyses of char and activated carbon, the surface of activated carbon has large number of pores of irregular and heterogeneous morphology.

Jan 1, 2016

By X. L. Song

A large amount of tailings in concentrators bring a series of problems to the environment and society. It is significant to reclaim the huge tailings and reuse them in industries in order to utilize mineral resources adequately. Primarily Lead-Zinc tailings with a certain quality of clay and feldspar were used to produce ceramic tiles by sintering method under specific technical conditions. By testing the properties of the ceramic tiles, it was shown that the amount of Lead-Zinc tailing used in the tiles was 60%~70%, and the mechanics properties were good. The optimum proportion parameters were Lead-Zinc tailing 60%, clay 35%, feldspar 5%, and the maximum flexural strength of tiles was up to 38.2MPa when it was sintered at 1090? for 30min. Its flexural strength, water absorption and thermal shock resistance reached the State Standard of GB/T4100.4. The product is suitable to be used in pavements and paths of parks.

Jan 1, 2014

By Guan-zhou Qiu, Shui-shi Liu, Yu-feng Guo, Tao Jiang

"The preparation of high-quality synthetic ruitle from electric furnace titanium slag was systematically investigated by activation roasting followed by acid leaching process. The results showed that impurities such as Ca and Mg in titanium slag can be effectively removed and TiO2 grade of the product was markedly improved by the process. High-quality synthetic rutile containing 88.54% TiO2, 0.42% (CaO+MgO) was obtained under the conditions that roasted with 7.5%(wt) H3PO4 at 1000 oC for 2h, followed by two-stage leaching in boiling dilute sulfuric acid for 2h. Mechanism studies showed that anosovite solid solution and silicate minerals were reacted with phosphoric acid in the roasting process. As a result, titanium components in titanium slag turned into rutile (TiO2) and impurities were transformed into acid-soluble phosphate and quartz.IntroductionWith the gradual depletion of natural rutile and the rapid development of titanium industry in China, the natural rutile reserves cannot satisfy the requirement for production of titanium pigment and titanium sponge. Ilmenite is, therefore, becoming main raw material for titanium industry. However, because of its low TiO2 grade, it generally requires preconcentration to titanium-rich material such as titanium slag or synthetic rutile [1-3].Ilmenite resources are extremely rich in Pan-xi area of China, which account for 90.54% of total ilmenite reserves in China [4]. The titanium slag produced by electric smelting of ilmenite concentrate has high contents of Ca and Mg, and is not suitable as a raw material for chloride process and titanium sponge production. Therefore, upgrading titanium slag to prepare raw material suitable for chloride process and titanium sponge production has important significance for the development of China's titanium industry."

Jan 1, 2011

In this work, the crystallization of Carnallite from waste brine of Qaidam Basin in Qinghai province was studied based on NaCl-KCl-MgCl2-H2O phase diagram. According to this study, a new crystallization pathway to recycling waste brine was developed. The carnallite salt was formed by using this technology during the waste brine evaporation. The experiment data shows that 5 tons of waste brine was required to form one ton of the carnallite. The average grade of carnallite prepared by using this procedure was about 19.40% of KCl, 16.92% of NaCl, 28.80% of MgCl2, and 0.82% of CaSO4. This study provides an opportunity to utilization of the waste brine.

Jan 1, 2012

By Huimin Lu, Zegao Sun, Zhijiang Gao

The traditional Ti6Al4V alloys were obtained by the smelting reduction of V-Ti bearing beach placer by rotary hearth furnace and aluminothermic reaction in laboratory. First, it gets he lp from combined rotary hearth furnace and grinding magnetic separation process to prepare titanium slag containing vanadium. In this study, a neural network model was used. The comparisons between experiment results and neural network simulation results show that genetic algorithm (GA)-based on back propagation (BP) method can predict the degree of reduction and separation of iron and slag with higher prediction accuracy. Then by aluminothermic reaction process, the optimized process parameters for Ti-V-Al alloys were searched. Al can deoxidize metal V and Ti from the metal oxides of artificial rutile containing vanadium. Finally, traditional Ti6Al4V alloy can be obtained by remelt and adjust the constituents.

Jan 1, 2016

By H. M. Gao

According to the difficulty of dolomite removal from collophanite,normal-reverse floatation process has been adopted in floatation with the use of highly selective collector G-4 and depressant S721. Good indexes of flotation have been obtained with the run-of-mine ore containing 17.96 % P2O5 and 2.31 % MgO being upgraded to a concentrate containing more than 30% P2O5 and less than 1% MgO. The reagent interaction mechanism in low grade collophanite flotation has been stu-died by FTIR analysis and theoretical calculation. The results indicate that the interaction between collector G-4 and collophanite is the result of chemical adsorption in combination with physical ad-sorption with chemical adsorption playing the major role. Depressant S721 adsorbs on dolomite surface to form a water film and effectively depresses the flotation of dolomite and reduces the MgO content in the concentrate.

Jan 1, 2014