Search Documents

The fracture behavior of second phase particles and the role of matrix material on the wear resistances of the three Al-Si alloys containing 8, 17, and 19% Si were investigated using single pass scratch testing technique by applying normal loads between 0,15 and 5,00 N, in ambient air, Optical microscopy and SEM with EDS were used to analyze microstructures and morphologies of scratch tracks of the Al-Si alloys, The results showed that needle-like Si particles fractured under a load of 0.50 N, while block-like Si particles fractured at loads above 3,00 N, The Al-17% Si alloy with large number of needle-like particles (area fraction 16,4%) exhibited the highest coefficient of friction (0,8) and the widest scratch track, The Al-19%Si alloy containing high Si percentage and larger number of block-like particles (area fraction 16%) exhibited the lowest coefficient of friction (0,37) and the narrowest scratch track width. Presence of block-like particles was effective in reducing the amount of material transfer from Al-Si alloy surfaces to the counterface.

Jan 1, 2005

By P. M. Lin

A subsidence monitoring program over a longwall panel was established (1) to explore the impacts of dynamic subsidence on the ground surface and structures and (2) to correlate the movements between the structures and their corresponding points on the ground. The program consisted of a transverse line survey and a series of survey points around the structures on the ground surface and their corresponding survey points on the exterior walls of the structures. The vertical displacement of each point can be expressed as: where Si is subsidence at i point; Sif is the final subsidence at i point; F is face location in terms of distance from the i point and SD is seam depth. The development of subsidence can be divided into five stages. Damage to the structures starts at the beginning of the second stage, The maximum damage developed in the middle of the third stage. The relationship of the vertical displacement between ground surface and structures can be expressed as: G = aH + b where G is ground displacement, H is structures displacement, and a and b are constants. The relationship is linear. However, the strain is non-linear and more complicated because of the interaction of the ground surface and structure.

Jan 1, 1989

By E. H. R. Schümann, H. Wagner

SYNOPSIS The paper gives a detailed overview of the history of subsidence engineering on South African collieries. Surface displacements resulting from total-seam extraction are discussed, and the important role of local geology is highlighted. It is shown that the differences in subsidence behaviour between South African and European collieries can be attributed to the presence of competent strata in the overburden of South African coal seams. Criteria are given for the prediction of the most important subsidence parameters, and a new model for the simulation of surface subsidence above total-extraction panels is introduced. The final section of the paper deals with the damage to surface structures caused by total-seam extraction. A brief summary of the most important undermining experiments on South African collieries is given, and it is concluded that local experiences of damage compare with those in Europe.

Jan 1, 1991

By J. L. Byers

THE metals of the platinum group, ruthenium, rhodium, palladium, osmium, iridium and platinum, have certain characteristic effects on the structure and appearance of the cupellation bead. These effects are dependent not only on the particular member of the group present, but also on its concentration. The extent and quality of these effects, however, have not received investigation worthy of their importance. Bannister and Patching investigated the qualitative effects of some of these metals in 1913. This paper deals with a possible rapid qualitative and quantitative delineation of the effects exerted on the cupellation bead by the various metals in the platinum group. More particularly, the paper correlates quantitatively the presence of such metals with their characteristic structural and surface effects. Inasmuch as the various members of the group are more frequently associated with gold than with silver, the gold button will receive the greater consideration. The past two decades have seen a much greater interest manifested in this particular group of metals, because of the increased industrial demand for them. There has been a constantly growing need for assays that will not only express the silver and gold values but also indicate the presence of the other metals. If these indications could be used as quantitative criteria, their value would be greatly increased, because the methods of chemical analysis for the elements of the platinum group are lengthy, involved and unreliable except when the analysis is made by an expert and experienced rare-metal analyst. The materials for the X-ray diffraction examination of the different beads were prepared by filing and screening to -200 mesh, and were then rayed in a General Electric X-ray diffraction unit. The filed samples were treated magnetically in order to eliminate any possible steel particles. Sodium chloride and C.P. gold and silver were used as standard comparators.2 (See Table 1.)

Jan 1, 1932

By H. K. Livingston

A TECHNIQUE has been developed which makes it possible to determine the spreading pressure of liquids and solids, for simple systems. Data for surface tensions, interfacial tensions, spreading pressures, and contact angles for water, heptane, and silica are tabulated. These results can be applied to the evaluation of capillary rise and displacement pressure in a petroleum reservoir. Appropriate equations are presented and the application of these equations is discussed. The presence of surface-active components affects both capillary rise and displacement pressure and also seems to influence the rate of fluid flow.

Jan 1, 1942

By Christopher J. Bise

INTRODUCTION The level of analysis for the selection of extraction practices and equipment for surface mining differs significantly from that found in underground mining. In underground mines, manufacturers establish the operating ranges of the equipment, such as continuous miners, loaders, and boring machines, based upon required clearances. Even in conventional mining, the drilling and blasting operation is usually based upon experience. The selection of extraction methods and equipment for surface mining is more complex. Since the equipment is not as confined as in deep mining, and the topography tends to be highly variable over the limits of the mining property, primary extraction equipment must be sized according to reach and capacity. Further, due to the depositional characteristics of the over- burden, drilling and blasting patterns must be well- designed to provide proper fragmentation. The following sections provide a general outline for the selection of surface excavation practices and equipment. The topics covered include drilling and blasting and the selection of both primary extraction equipment (draglines and stripping shovels) and secondary extraction equipment (bulldozers, scrapers, and front-end loaders). EXCAVATION FUNDAMENTALS Before discussing surface excavation, a few concepts need to be defined. A bank cubic yard of material is equal to one cubic yard as it lies in its natural or undisturbed state. A loose cubic yard is that portion of a bank yard that after being disturbed has expanded to measure one cubic yard. Swell is the volume increase of a material when it is removed from the natural state. Finally, load factor is the percentage decrease in the density of a material from its natural state to a loose state. Table 1 summarizes these concepts for various materials. When the amount of overburden to be removed to meet a predetermined production rate is established, a suitable bucket size for the primary stripping equipment must be calculated. The following equation can be used: NBSIZE = TBC/[(OF) (BF)] (1) where NBSIZE is the actual bucket capacity after considering the swell percentage, the bucket fill factor, and the operating efficiency; TBC is the theoretical bucket capacity (TBC = COB/NTCPM); OF is the operating efficiency; BF is the bucket fill factor; COB is the cubic yards of overburden to be removed; NTCPM is the number of theoretical cycles per month [NTCPM = (SMH) (3600)/(CT)]; SMH is the scheduled monthly hours; and CT is the cycle time in seconds. FRAGMENTATION PROCEDURES Drilling Where the strength of overburden material is such that blasting is required prior to excavation, drilling is conducted before using explosives. Two methods of drilling are found in mining-percussion and rotary. Penetration of overburden by percussion drilling is carried out by successive impacts of the bit into the rock. Emphasis in this section will be placed on rotary drilling, because for surface mining it is the most versatile form of overburden penetration. Rotary drilling is conducted by rotating a rigid string of tubular rods to which a rock-cutting bit is attached. The drilling energy is supplied by rotation as well as thrust and the cutting action consists of abrasion, scraping, spalling, or chipping. The size range for rotary-drilled blastholes is from 4 in. to 15 in., with 9 in. and 12 in. being common sizes. There are two types of bits used for rotary drilling-drag and rolling cutter. Drag bits are applicable in soft to medium-soft shales or their equivalents. Since their effectiveness is dependent upon a successful scraping action, drilling thrust is lower for drag bits than for rolling cutter bits; the opposite is true for torque requirements. The bits are usually fitted with replace- able tungsten-carbide cutters. Rolling cutter bits, though available in a two-cone configuration, are usually of the three-cone style (Table 2). The rolling cones have either large steel teeth for drilling through soft formations or small tungsten-car- bide inserts for drilling through hard formations. Table 3 relates bit size and weight to the strength of the rock. The major advantage of rotary drilling is its rapid drilling rate. This is due to the fact that, unlike percussion drilling, rock penetration is uniform with depth. Blasting Effective bank preparation deals not only with the fragmentation of overburden but also with the mini-

Jan 1, 1986

By John Wulff

IN a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot profilometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200° and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 415° and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on ½ sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples whose surface temperatures exceed only about 250°C. EXPERIMENTAL PROCEDURE The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, 1 by 1 cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale. On a lapping machine of the Graton2 type, both sides of each sample were polished to a flatness of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any deformations induced by surface preparation. Samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrument shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. Suc-

Jan 1, 1941

By Daniel S. Mazzei

This paper will be a general discussion of surface flooding considerations as they affect mining facilities site selection, based primarily on experience with several such problems with which MSHA's Bruceton Technical Support staff has been involved. The detailed analytical procedures used in arriving at engineering solutions of these problems will not he presented here; the emphasis is on drawing attention to this additional aspect of mine design which hitherto has been largely overlooked due to insufficient awareness, information and criteria. The paper's purpose is to stimulate thought and offer guidance concerning the selection of sites for mining facilities in light of the potential for flooding problems caused by surface waters. Flooding by surface waters, would generally not be a serious consideration in areas of relatively low topographical relief, i.e. flat lands, although there are exceptions to this rule, for example, in Western areas where flash flooding is a major concern. Therefore, this discussion will mainly apply to areas where the severity of surface flooding would be amplified by the topography-large, well defined watersheds of considerable relief, i.e. mountainous areas. In these regions, steep valley walls cause any rainfall to flow quickly into the relatively narrow valley bottoms. These valley bottoms provide little flow area during storm conditions, so deep and rapidly flowing streams result.

Jan 1, 1982

By M. W. Rutland, E. Manev, R. J. Pugh

Data collected from several different fundamental surface chemical techniques were compared to study the interfacial interactions in the dodecylaminelmica flotation system. In the present study, the method used was the microinterferometric free foam film technique of Scheludko (1967) in which the stability, thickness and interfacial potentials at the air/dodecylamine solution interface were determined. These results were compared to previously published data, obtained from surface force measurements (Rutland et al. 1992), in which the interaction and hydrophobic adhesion (pull-off force) between molecularly smooth mica sheets in the amine solution had been reported. Also equilibrium contact angle measurements were used for comparison. The data was collected over a range of pH values and related to the batch flotation response of mica in dodecylamine solution. It was found that maximum flotation occurred at pH 8, but this did not correlate with the minimum in double layer interaction potential. However, it appeared to correspond with a tightly packed collector monolayer giving maximum hydrophobicity to the mica surface. Finally, from the extended DLVO theory, it was shown that heterocoagulation between the bubble and the mica could only occur, providing there was a very long range hydrophobic interaction force to counterbalance the repulsive van der Waals and electrostatic forces.

Jan 1, 1995

By J. H. Zhang

An atomic force microscope has been used to measure the forces acting between two silica and two rutile surfaces in the presence and absence of cationic surfactants, CnTACl (n = 12~18). The forces measured in the absence of surfactant can be fitted to the DLVO theory. At short separations, however, the silica surfaces exhibited repulsive hydration forces, while the rutile surfaces did not. On the other hand, the forces measured in the presence of the cationic surfactants show long-range attractions that are larger than the van der Waals forces. The long range attractions are the strongest at of the point of charge neutralization (p.c.n.), which decreases with increasing surfactant chain length. The possible origin of the long-range attraction has been tested in view of the charged-patch model of Miklavic et al. (1994). However, the sizes of the patches back-calculated from the model were much larger than those the patches (or hemi-micelles) determined experimentally and reported in the literature. It is, therefore, suggested that the long-range attractions observed in the present work are due to the structural response of the water molecules in the vicinity of hydrophobic surfaces.

Jan 1, 2014

Surfaces forces have been measured between gold sphere and gold-coated glass plate in xanthate solutions using an atomic force microscope (AFM). The measurements conducted in potassium amyl xanthate (PAX) and potassium ethyl xanthate (KEX) solutions showed long-range hydrophobic forces, with the force curves showing no evidence for nanonubbles on the surface. The strongest hydrophobic force was measured at contact angle of 94° with a decay length of 23 nm. The hydrophobic force became weaker at higher concentrations and after a long immersion time, which may be attributed to the xanthate species adsorbed on top of the first mono layer. The hydrophobic force became stronger when the residual xanthate solution is displaced by pure water, indicating that hydrophobic force becomes the strongest in pure water.

Jan 1, 2009

Many investigators measured surface forces between hydrophobic macroscopic surfaces using atomic force microscope (AFM). Some investigators observed long-range attractions and attributed them to the presence of hydrophobic forces, while others suggested that they are artifacts of the nano-bubbles and cavities associated with the hydrophobic surfaces. Still others suggested that the long-range attractions are due to the electrostatic interactions between charged patches present on opposing surfaces and hence are unrelated to surface hydrophobicity. In the present work, we have measured long-range attractions between gold- (or silver-) coated surfaces hydrophobized in potassium ethyl xanthate (KEX) solutions at pH 9.2 under controlled potential conditions. The results of our AFM force measurements are consistent with those of the contact angle and voltammetry experiments, indicating that the long-range attractions are hydrophobic forces.

Jan 1, 2012

It is argued that the capture of par- ticles by bubbles is primarily caused by hydrophobic ("structural") attraction forces. Neither dispersion forces nor double-layer forces can account for hydro- phobicity, though the latter are known to influence the kinetics of capture. The recent experiments of Israelachvili and Pashley (Nature, 300: 341-342, 1982) with hydrophobic mica plates provide the first measurements of the range and magni- tude of hydrophobic interaction forces.

Jan 1, 1984

By Clyde DeRossett

Surface fractures, sometimes of significant size, are observed in eastern Kentucky over high extraction areas. Field observations were correlated with mine maps and a regional subsidence prediction computer model. The opening of large fractures is attributed to the presence of a pre-mining joint system, which exists near outcrop in the eroded Appalachian plateau. Lithological composition of the overburden influences the process of fracture opening. No correlation was found between the areas of the predicted maximum horizontal extensions and the actual location of fractures. In this paper a mechanism of fracture formation as a result of the high extraction mining is presented, with recommendations for mine planning to minimize surface damage.

Jan 1, 1993

By I. Yildirim

Free energy of interaction between particles in water can be calculated if one knows the values of appropriate interfacial tensions, which in turn can be determined from the surface free energies of the particles involved. The latter can be determined using the Van Oss-Chaudhury-Good (OCG) equation. This method requires the measurement of contact angles of well-defined liquids on the surfaces of the particles of interest. In the present work, the contact angles were determined using heat of wetting, capillary rise, and thin-layer wicking methods. The results are compared, and the utility of the surface free energy data obtained from the contact angles are discussed.

Jan 1, 2002

By A. Wahab Khair

This paper presents an analysis of surface ground movements recorded from two longwall mines in Northern West Virginia which operate in the Pittsburgh Seam. The instrumentation areas consisted of four panels, two at each mine, covering various sections with unique topographic features. Instrumentation consisted of survey monuments on 25 to 120 ft. spacing. Vertical and horizontal ground movements were measured at specified intervals to determine subsidence rate, developing and final subsidence profiles, angle of draw, horizontal displacements and associated strain profiles. A relationship between panel depth and width and the subsidence factor was also developed.

Jan 1, 1988

By John W. Brauns

18.1-RAILROAD JOHN W. BRAUNS Conventional railroad haulage can be employed at both open-pit or strip and underground mines-in the latter case, largely for transfer of ore from distant openings to processing plants, or processed material to loading points or docks, using standard hopper cars for bottom unloading or gondolas for rotary dumping. The major application, however, is in surface mining for moving ore and/or waste out of the pit to a crushing plant or dump. Consequently, the following will deal largely with this phase of railroad operation, though the conclusions apply equally, for the most part, to other rail-type surface haulage. In surface mining, trains consisting of a locomotive and gondola or side-dump cars suitable for loading by power shovels are used. Gondolas are restricted to hauling ore as a rotary dumper is required. Side-dump cars are more versatile, carrying both ore and waste, but because of their additional dumping mechanism they are likely to be more expensive to maintain.' Also they weigh up to twice a flat-bottom car of the same capacity and. therefore, fewer" cars can be hauled per train. Standard-gage track is most commonly used. Track systems incorporate low-quality temporary track where moves are frequent and permanent high-quality track on main lines. Rail haulage can be used alone, or in combination with other surface haulage methods, thus permitting a selection best adapted to the peculiar requirements of each mining project. 18.1.1---GENERAL APPLICABILITY, CONTROLLING PHYSICAL CONDITIONS For handling rough rock, the shovel-train system is unexcelled.' The ideal applica¬tion is in a large, but not excessively deep, open pit mine from which the coarsely blasted ore and waste must be transported over 3 mi. If. in addition, a high production rate is to he maintained, railroad haulage probably will afford a lower cost per ton transported. Grade must he relatively gentle-usually 3% uphill and 4% downhill. The greater the differences in elevation involved, the greater are the track grade space requirements; for example, a 3 c ramp out of a pit only 300 ft deep is almost 2 mi long. Main-line track locations should he selected carefully so that the number of moves during the life of the mining operation can he kept to a minimum. This applies both to the ore haulageway and that for waste. Such moves are not only expensive, but are difficult to execute without adversely affecting production rates. The large mine affords greater opportunities for judicious location of semipermanent trackage. Figs. 18-1 and 18-2 illustrate typical track layouts. The effect of terrain in considering railroad haulage is confined chiefly to the initial cost of the installation. Grade construction in mountainous territory is ap¬preciably more expensive. However, if that expense can be borne, the subsequent maintenance cost of trackage will not he much higher than in areas of low relief.

Jan 1, 1973

By C. M. K. Boldt

Between 1989 and 1991, the greatest number of accidents in surface coal and metal/nonmetal mines involved haulage trucks. In 1995, the most frequently cited factor contributing to the 100 fatalities in these mines was powered haulage. In 1996, over 50% of the 84 Fatalities in mining that year were in surface mining. Because some of the world's largest mobile equipment is used in surface mines, and this equipment is involved in so many accidents and fatalities, new technologies are needed to alert truck drivers and people in spaces around the truck to the possibilities of collisions.

Jan 1, 1999

Underground mining in the West Moreton coal field started in the 1870's. Subsidence related to coal mining activities is an ongoing problem facing planners and developers in the Ipswich area in South Eastern Queensland. The history of coal mining in the area over the last 110 years has left the legacy of periodic surface instability in several areas. In general, modern engineering analysis with current mining methods combine to create predicatable analysis of surface stability and movement. Where old workings using several variations of the bord and pillar system are affected by current activity, the predictibility of the surface movement is greatly reduced. Geological complexities further complicate the analysis. Mining and the related dewatering affects the stresses on pillars in old workings. This is caused by reducing buoyancy effects caused by changes in the water levels in old workings. Of particular relevance is the depth of workings and strength of the coal and overburden. The type of subsidence affecting the surface can range from localised pillar failure, to roof failure and potholing and the likelihood of the particular form of subsidence can be assessed from studying the workings in relation to the stratigraphy and structure of the coal measure Formations.

Jan 1, 1988

By R. T. Hernández, I. Hilerio, A. Altamirano, M. A. Barrón

"The principal objective for finishing surfaces is to protect and/or to decorate them. This can be achieved by adding or removing material from the work surface. The addition of aggregated material is called coating or recovering. In this work, mecano-chemical techniques are investigated for surface finishing. For these techniques, barreling or polishing by the friction method will be used. These are the cleaning or finishing processes most used for great volumes of small pieces. These methods improve the surface finishing by eliminating burrs, sharp pointed, tool marks and crusts of casting. They are used to clean metallic pieces, ceramics and polymeric materials. The process is based on rubbing or friction by abrasives. The pieces are arranged in the barrel with an abrasive and an additive (water or chemical additive). The machine produces a rotating movement on the pieces. When the abrasive passes against the surfaces of the pieces, it produces an action of rubbing and impact that cleans the surfaces. The rubbing action is developed when the upper layer of the charge slides to the lower extreme when the barrel rotates. The barrel can be hexagonal or octagonal to facilitate the sliding of the charge. The barrels can be between 15 to 120 cm in length and they can have almost any diameter and velocity of rotation. There are several types of barrel: individual, multiples, and multiple compartments. The barrels are rotated using a wheel spindle or rolling pins, that the can ride horizontally or be tilted to produce an additional movement of the charge.IntroductionShot penning is a cold method in which compressive effects are induced on an exposed surface of a metallic piece, by the impact of a rain of shots directly on the surface of the metal, at great speed under controlled conditions. This differs from cleaning with the help of air, because even when shot penning cleans the surface of the metal, this function is incidental. The main purpose of shot penning is to increase the resistance of the piece to fatigue. The process has other applications: raises the tensile strength and decrease corrosion fracture."

Jan 1, 2012