Search Documents

By Readett D. J

Soluble salts can be removed from Bowmans lignite by water and acid leaching. The success of the removal of water soluble or acid exchangeable impurities is directly associated with the efficiency of dewatering these slurries. The filtration characteristics of a slurry at its natural pH (4.0) were poor, with a filter cake moisture of 65%. Acid treatment of the slurry at pH2 caused the filter cake moisture content to drop to 61 %. Various oils, oily surfactants and a flocculant were tested to determine the conditions for minimum filter cake moisture. A series of pilot scale filtration tests were conducted on flocculant dosed slurries with and without washing on a horizontal test unit. Moisture contents of 54% were obtained in laboratory testing using high additions of oily surfactant. For the pilot scale test work, moisture levels close to 60% were obtained with low flocculant additions, similar to results obtained in laboratory studies. Removal of soluble salts could be correlated directly to the final moisture content of the filter cake. This process of leaching followed by filtration resulted in the removal of approximately 75% (more than 80% with washing on the cloth) of the sodium chloride originally present in the lignite.

Jan 1, 1989

By Q Zhou, G Barrett, Y Choi, J Jiang

As part of a general review of processing double refractory ores through Barrick GoldÆs autoclaves /carbon-in-leach (CIL) facility at Goldstrike, a study was made to evaluate the use of surfactants for reducing the loss of gold during cyanide leaching of preg-robbing gold ores. Consistent improvement of gold recovery was observed with surfactants at various testing conditions. This paper will discuss the results obtained from laboratory and pilot-scale testing, as well as, review potential mechanisms for the observed improvement in gold recovery.CITATION:Zhou, Q, Barrett, G, Jiang, J and Choi, Y, 2013. Surfactants for gold recovery improvement with preg-robbing gold ores, in Proceedings World Gold 2013 , pp 367-372 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By M. E. Lewellyn

A lower moisture content for a clean coal product means increased Btu content, or increased yields at the same Btu content, and lower operating costs. The conventional surfactant-based dewatering aids effeciently lower the moisture content but often the presence of residual surfactant in the filtrate and recycle water causes problems downstream. ACCOAL-DRI 1000, a surfactant-based dewatering aid, was developed to solve this problem by minimizing the downstream effects while efficiently lowering the moisture content. The theory of the use of surfactants in filtration will be discussed as well as the development and field evaluation of this new product.

Jan 1, 1988

By E. D. Goddard

There are similarities, and differences, in the surfactants used in cosmetics and detergents. In both applications anionic surfactants constitute the major category. Their main function is to clean, i.e. remove grease and particulate matter from fibrous or hard surface substrates. Cationic surfactants are used for conditioning substrates. Nonionic surfactants can function as a substrate cleanser but are seldom used as such in cosmetics; however, selected non-ionics are often employed as a primary emulsifier. Several specialized nonionic surfactants are used as a secondary surfactant in formulations to promote foaming and emulsification. Specific examples and modes of action of surfactants will be presented.

Jan 1, 1988

By D V. Boger

The use of chemical additives to initiate such processes as particulate separation through flotation or dewatering through flocculation, is common in the mining industry. The dosing of additives is none the less poorly controlled from a process control viewpoint and it is perhaps fortuitous that over-dosing or misuse of chemicals is rarely catastrophic to the production cycle. In many cases, such events would go undetected if it were not for economic considerations. Recently, the advent of orebodies with finer mineral disseminations and the push for greater efficiencies in both production and tailing disposal have resulted in the need for greater control of the dosing and utilisation of chemical additives. The need to grind at higher pulp densities and to finer sizes and to dewater to higher solid contents are but two examples that require a more stringent understanding of the true role of additives in controlling the rheology of suspensions and the influence of additives on the surface chemistry of particles. The inter-relationship between the surface chemistry of particles and the role of additives in controlling suspension rheology is now well understood for systems in which the average particle shape in the mixture is spherical or close to spherical. Luckily, this is the case for a large number of systems in the mining industry and the true role of typical additives in these systems will be explored. Difficulties arise for suspensions containing clays or other platey or needle shaped minerals and in many cases, quite small quantities of platey minerals dominate the rheology of suspensions. The role of additives in controlling the rheology of asymmetric particle systems is more complex but the effect of the additive in changing particle alignment in solution is the key to understanding suspension behaviour. The manipulation of the rheology of asymmetric particle systems will also be explored.

Jan 1, 1998

A C-CORE study on behalf of the government of Newfoundland identified the inner continental shelf off northeast Newfoundland as having a relatively higher potential for hosting placer gold than other parts of the inner shelf. Under the auspices of the Canada-Newfoundland Cooperation Agreement on Mineral Development, the Geological Survey of Canada conducted a three-year project to map the distribution of surficial sediments and the abundance of placer minerals (particularly gold) from White Bay to Cape Freels. Much of the study area is a fjord coast, with steep rocky slopes and scattered gravel beaches. The extreme east, from Hamilton Sound to Cape Freels, has a wide, shallow inner shelf, sandy beaches, and extensive coastal dunes. Relative sea level was high in the late glacial period. It has fallen continuously in the west, but in the east it dropped to -19 m, before rising to within several metres of the present level by 3 ka. In terms of surficial sediments and processes, five zones are identified: (1) Deep offshore deep basins that contain thick postglacial mud overlying glacialmarine gravelly sandy mud. This zone is below a depth of 370 m in White Bay, 300 m in the Notre Dame Basin. 2) Basin transition zone in which the sea bed has been eroded by currents, so that glacialmarine sediments are exposed in places. Winnowing has formed an uppermost layer of muddy gravel. There is a slight potential for enhanced levels of fine particulate gold, but the gold would not be exploitable. (3) Iceberg impacted zone Above 200 m the keels of icebergs impact the sea bed, causing furrowing and pitting. Furrows predominate in deeper areas, and pits are concentrated at the inner boundary of this zone. Iceberg turbates have developed in shallow waters (60-100 m). Combined with winnowing, iceberg turbation could enhance the potential for concentration of fine particulate gold, but not into economic quantities. 4) Wave dominated zone Above approximately 60 m the sea-bed sediments are highly mobile due to waves, currents, and iceberg impact. Sand is either rippled or organised into sand waves. Gravel is either poorly sorted, and organised into

Jan 1, 1995

By Scott G. Britton

Until now, only the range of typical construction projects which are repeated over and over during the life of a coal mine have been discussed. This chapter looks at underground construction projects which occur only once or twice during the life of any given mine and are major construction projects in both time and cost. These projects usually require the services of an outside engineering and construction firm with hands- on experience in design installation. Because of this involvement with engineering and construction firms (EIC), the role of the construction engineer will change from one of actively de- signing and directing tasks to one of planning, inspection, and quality control. To reflect this role change in the discussions, the focus of this chapter will be changed to a broad overview of project participation. Of course, the projects under consideration in this chapter could easily fill more than one book on their design and installation. In addition, major construction projects are extremely site specific, requiring months of data collection about site geology, physical conditions, and potential excavation and construction requirements. Therefore, no attempt shall be made to discuss any detailed construction aspects as was done in earlier chapters. The purpose of this chapter is to present the fundamental concerns of a staff engineer or supervisor. This engineer does not make the decisions on choosing the EIC firm, but assists and interacts with their project team to accomplish the goals set forth by higher management. The construction topics to be reviewed fall into three main categories. The first category is highlighted by the installation of a main surge bin; the second is typified by the construction of an underground shop; and the third category encompasses special projects such as rotary dumps, crusher stations, and foremen's offices. These categories highlight the differences between degrees of mine responsibilities for project completion. The first topic is usually a turnkey project by an E/C firm for a given mine. The second topic represents the leading role of the mine in the project with a contractor as a support service or equipment supplier only. The third topic, special projects, is an example of a joint venture-between a contractor (leading partner) and mine management. These roles can change with any given project, but the changes in management responsibilities for the construction engineer can be nicely illustrated for the purposes of this text. The first step toward constructing major mine projects is to analyze the mine which influence their design. From the mine management standpoint, these parameters should reflect the role the mine will play in the project construction. In other words, what is the nature of the proposed mine environment and what are the material, labor, and time requirements needed to assist or direct the chosen engineering and construction firm? Answering these questions requires some basic project planning and cost estimation work. Here, only a general treatment is necessary, since detailed discussions of these topics will follow in Chapters 8 and 10. For those persons interested in the role of the EIC contractor, I suggest beginning by reviewing the article by Beall, "The Role of an Engineering and Construction Contractor," presented in the October 1980 issue of Mining Engineering magazine.

Jan 1, 1983

By Quentin L. Rhoton

"The use of explosives in a surgical manner was approved to facilitate, due to time constraints, anextremely significant paleontological find in the Plunket Point area of the Dominion Range, Antarctica. The organic material revealed by surgical blasting techniques may have altered basic scientific dogma on Antarctic glaciation theory."

Jan 1, 1999

By A. Martikainen, H. Dougherty

"At the Kemi Mine, a recent expansion into the Surmaoja orebody required an increase in ventilation capacity. A new ventilation shaft was built with two main fans. The installation is near the entrance gate and only 1.7 kilometres from the nearest permanent dwelling. The main fans were first taken into use as exhaust fans in October 2014. Shortly after the fan installation, comments concerning fan noise were received from the neighbours. The first noise measurements were taken at the main fan installation site by Outokumpu personnel in March 2015. Due to higher than expected recorded values, during late June, 2015, a two-week environmental noise study was planned by the engineers and executed by a consultant specialized in noise measurement. The measurement results were analysed and compared to the requirements of the environmental permit and Outokumpu’s factory standards. While the measured values at the nearest dwelling were within the environmental permit limits, high noise values were recorded at the fan station. A second two-week study will be performed after construction of the main-fan heating station has been completed. Actions taken will depend on the outcome. INTRODUCTION The Kemi Mine is a part of the Outokumpu chain of integrated ferrochrome and stainless steel manufacturing in the Kemi-Tornio region in Finland. The mine itself is a large underground operation with a production capacity of 2.7 million tons of ore per annum. It is also the European Union’s only chrome mine, and at present (2015) the mine extracts 2.4 million tons of chrome ore per year. Safety, cost-effectiveness, and environmental friendliness are hallmarks of the Kemi Mine. Environmental impact produced by the operation of the mine is limited due to the insolubility of the oxide chromium ore, the gravity-based and chemical-free enriching process as well as the closed circulation system of the process water which serves both the whole mine and the enrichment process (Outokumpu, 2015). Importance of the environmental impact of the Kemi Mine is amplified by its closeness to the cities of Kemi and Keminmaa with the nearest habitants living less than 2 km away from the mine site. To show the cooperation with residents the Kemi mine organizes special “neighbour days” for the habitants of the areas closest to the mine. Also, information letters are sent to the neighbours, when changes that may affect the neighbours are being planned and executed."

Jan 1, 2016

By Kevin Tallent

The use of military-type energetic materials in commercial explosive products is not a new concept. In the United States, the techniques for utilizing significant quantities of surplus military explosive materials by commercial explosive manufacturers dates back to the 1950’s. At times, explosive companies have found surplus military high explosives and propellant materials to be suitable ingredients for their commercial explosive products. The availability of these military-type energetic materials has varied over the past 50 years, as a function of the military’s strategic defense needs and the advances in modern weapon technology. For the most part, the commercial explosives industry has been able to implement methods for safely incorporating military-type high explosives and propellant materials, whenever these surplus materials become available. During the past 5-6 year period, a large amount of military-type energetic materials have once again become available for recycling into commercial explosives. This situation can be attributed to a number of factors, such as the political changes in Europe, the development of more sophisticated weapons systems, and the increased EPA pressures on the U.S. Department of Defense for disposing of surplus energetic materials. As in the past, U.S. commercial explosive manufacturers have made efforts to recycle these surplus materials into their explosive products. This paper describes some of the commercial explosive products that are currently on the U.S. market, which contain rocket and gun propellants as energetic ingredients. Some U.S. explosive companies, such as DYNO NOBEL, ORICA and Slurry Explosive Corporation, have been able to recycle significant quantities of surplus smokeless powder and composite propellants as energetic ingredients into their commercial Blasting Agents. The successes enjoyed by these companies have once again shown recycling into commercial explosive products to be an economically and environmentally sound method for disposing of surplus military-type energetic materials.

Jan 1, 2000

By AIME AIME

In taking account of stock, on the occasion of the recent removal of the office of the Institute, it was found that pamphlet copies of the papers named in the list given below were on hand, in excess of the average number deemed adequate for future casual demand. Special reduced rates will be made for these surplus copies to members applying promptly. "First come; first Served." Author. Title. Ref. No. ASHBURNER, C. A. " Petroleum and Natural Gas in New York State." 273 MARTENS, A. "The Microstructure of Ingot¬ Iron and Cast Ingots." 626

Jan 1, 1907

By John E. Lens

Driving bridge foundation piles into glacio-fluvial sands and gravels and glacial tills brought surprisingly longer than predicted driving lengths on several recent projects in Vermont. In some instances, piles drove more than 40 feet past refusal depths predicted from Standard Penetration Resistances from borings terminating in glacial till. Overall, piles developed substantially less skin friction than predicted using common capacity formulas and drove as much as 80 feet longer than predicted in the moderate to dense gravelly and cobbly soils. These piles were driven for one to five span highway bridges within narrow valleys with bedrock ranging from 80 to over 200 feet deep. Piles were for both conventional and integral abutment bridges. H-piles were used for a variety of reasons including lower unit cost, better availability, and better ability to drive through cobbly soils in upper strata. Dynamic testing was used to evaluate capacity, including skin friction and end bearing capacity. In order to develop better pile length and capacity predictions for future projects, VTrans and one of their geotechnical consultants are collaborating to develop criteria for improved pile capacity predictions in these river valleys. We are doing this by evaluating driving and dynamic testing data from four projects in comparison with the Federal Highway Administration (FHWA) DRIVEN pile design software, and methods from Myerhof (1976) and Tomlinson (1981). Our overall objective is to provide a basis for choosing appropriate pile types and reliably estimating pile lengths for projects in this terrain. Bridge foundation design projects in other mountainous terrain share similar design and construction challenges to those encountered in these Vermont projects. These include: difficult exploration drill rig access requiring smaller rigs with limited capability to drill through cobbles and boulders deep enough to reach bedrock; limited experience with displacement piles as alternatives to H-piles in this geology; and relatively greater variability in soil stratigraphy between foundations at these sites as a consequence of the relatively high energy depositional environment in mountainous terrain. This paper presents the case history summaries of the pile driving, results of the ?back analysis? capacity evaluations, examples of solutions employed on these projects to address the lower capacities achieved, and resulting pile capacity design guidelines and prediction criteria for these geologic conditions based on data from these projects.

Jan 1, 2007

By D Brereton, C J. Moran

Intensive resource extraction, in the form of multiple mining operations, presents significant assessment and management challenges for resource developers, governments, community and the environment. Cumulative impacts, ie the successive, incremental and combined impacts (both positive and negative) of an activity on society, the economy and the environment, can place significant pressure on social, economic and environmental capital and render conventional mine-by-mine approaches to management ineffective. Cumulative impacts can be what are most important to environments, communities and economies surrounded by multiple mining operations because cumulative impacts are what they experience. There is much to gain from increased consideration of cumulative impacts. Unmitigated impacts have the potential to delay or even prevent expansion of mining in existing and prospective areas. On the other hand proactive management of cumulative impacts can benefit regional environments and communities and contribute to the industryÆs social license to operate. Resources are often not the limiting factor to better cumulative impact management. More effective coordination of existing resources may go a long way toward mitigation and enhancement, and better planning and assessment may help avoid impacts and exploit opportunities for efficiency gains through reduced duplication. In this paper we draw from working examples to present five practical assessment and management strategies applicable to resource companies to enhance positive, and avoid and mitigate negative, cumulative impacts. The strategies are presented based on their capacity for achieving outcomes, ease of implementation and cost effectiveness and are drawn from a multi-year study on the assessment and management of cumulative impacts in the Hunter Valley, New South Wales and a follow-up study to improve cumulative impact assessment and management practice in the Australian coal mining industry, both reported elsewhere.  

Jan 1, 2009

By Robert F. Chaken

The National Institute of Occupational Safety and Health (NIOSH) is dedicated to achieving "safety and health at work for all people -- through research and prevention." An important procedure in pursuing this goal is the NIOSH surveillance studies where the number of injuries are monitored according to demographic, employment, and injury characteristics. These numeric data are then used to identify injury risk factors, develop safety programs, and monitor implemented remediation methods. In essence, ongoing surveillance data form the bases for directing the resources of NIOSH in setting of research and prevention priorities, and in evaluating safety procedures. This surveillance techmque, which is based on the Public Health Service approach to identification and control of disease (1, 2, has been used quite successfully in dealing with relatively high number injuries such as hearing loss, musculoskeletal disorder, respiratory disorder, falls, etc. (2). However a problem arises when extending this paradigm to lower frequency traumatic events; particularly those often referred to as disasters (i.e., high impact events like mine explosions, airplane crashes, etc.). One can ask the question - there hasn't been a coal mine fire fatality in the U.S. for over ten years, to what extent should we be concerned with mine fire safety (resource-wise)? - The National Traumatic Occupational Fatalities (NTOF) system (4J which NIOSH uses to survey occupational fatalities annually, would suggest that underground mine fires would not be a high priority item in occupational safety. Yet, miners' (i.e., the exposed workers) do consider mine fires and explosions to be major safety concerns. I believe that we need to rethink our evaluation of work place disasters, what is worker exposure, and what are the underlying assumptions (both explicit and implicit) as to the impact that economic, societal and degree of hazard factors make on risk evaluation. The answers to all these problems, will require much broader considerations than those in current surveillance safety and health models. This paper discusses some facets of those considerations.

By Yi Luo, Jeremy Slagley, Arunkumar Rai, Steve Guffey, Syd S. Peng

Research was conducted to study the characteristics of longwall mining machine noises and to develop engineering controls for the reduction of noise exposure at longwall faces. Time-motion noise dosimeter data was analyzed and compared with existing databases. Experiments were conducted above ground on a stage loader/crusher to explore the potential of using active noise control (noise cancellation) in reducing the noise levels. A 5-7 dBA reduction in recorded stage loader noise was achieved. This paper presents the equipment, procedure and results of the noise surveys, as well as the active noise control experiments.

Jan 1, 2005

By F. T. Cawood

Monitoring of the slopes of surface mines can prevent loss of life, loss of equipment, loss of production and possibly the loss of the mine. The effectiveness of such monitoring depends on the extent to which slopes give adequate advanced warning before failing, and on the ability of the monitoring system to detect such warning. In this paper an overview is given of slope monitoring requirements, from both the geotechnical and survey points of view, as well as the types of equipment and instrumentation that are available. Legal issues relevant to slope monitoring are also dealt with. It is concluded that conventional geotechnical and survey instrumentation will continue to have their place in slope monitoring. However, the slope monitoring scene has changed substantially in recent years. A real and volume-based monitoring equipment is now available and this has provided, and will continue to provide, the means to improve safety, and to enhance productivity in mining. Its benefit to slope management is substantial. In the near future it is expected that data obtained from such equipment will add a much needed new dimension to slope engineering, and be used to improve slope designs and to optimize slope angles.

Jan 1, 2006

By John W. Straton

The President of the United States signed Public Law 91-173 on December 30, 1969 and the Federal Coal Mine Health and Safety Act of 1969 became law. The Bureau of Mines was required to promulgate regulations to implement the law. Unfortunately, some stipulations of the Act were not technologically possible. The USBM employed many new inspectors and had to instruct both old and new personnel in the requirements of the law. Mine operators and mine workers also had to be informed. There was a fair measure of inconsistency during this period. Progress is being made, however, and it is becoming easier for mining personnel to know what needs to be done. There are some unresolved questions, however, and there still appears to be an appreciable lack of uniformity in the application of the law by the many federal inspectors.

Jan 10, 1972

By Gloria L. Walker

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Information and Analysis activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1990

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects world-wide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1992