Search Documents

By Pierre Mousset-Jones, Geraint W. Harris, Robert Karlin, Jaak Daemen

In order to minimize the ore dilution induced by blast movement in surface mines it is necessary to quantify such movement. This will make it possible to more accurately locate the grade boundaries on the surface of a blasted rockpile prior to excavation. This paper describes the development and testing of a method to accurately measure the direction and magnitude of sub-surface blast movement. The technique involves the use of magnetic "radiometry, using a cesium vapor "radiometer and real-time differentially corrected, GPS system, to locate the post-blast position of magnetically enhanced target objects, whose pre-blast locations are known, without disturbance of the blasted rock. The objective is to design an accurate and efficient technique which can be integrated into a mines production cycle.

Jan 1, 1997

By M. Karmis

Surface subsidence has been recognized as an inevitable consequence of underground coal mining for several centuries. The damage resulting from this phenomenon has been witnessed in rural as well as in urban areas and ranges from simple land settlement to severe structural damage to buildings. Subsidence prevention is not feasible, at least under the existing technological and economic constraints of underground coal mining. Using a rational method of subsidence prediction, it has been demonstrated in many coalfields that subsidence control can be successfully practiced in order to reduce and accommodate subsidence within environmentally acceptable levels. This paper presents the development and testing of a subsidence model, based on the zone area method. This technique is a refined development of the influence functions and it is capable of investigating a mining plan of any shape, thus facilitating both longwall and room-and-pillar mining systems. More specifically, this study can be divided into two major efforts: (a) The development of the zone area model. This formulation was designed to accommodate the analysis of an optimum number of zones, over the area of interest, both accurately and efficiently. (b) The testing of the computer techniques with appropriate field measurements. In order to accomplish this, published as well as unpublished information was collected and analyzed according to a regionalized scheme. This procedure minimized differences in subsidence characteristics between the various coalfields and allowed a regional validation of the predictive capabilities of the model.

Jan 1, 1982

By V. Roze, R. N. Parkinson, R. Shepherd

The alphaDOSIMETER is a complete, integrated system designed to monitor the immediate worksite of underground miners where the disintegration for radon daughters is a risk to the health of mining personnel. The dosimeter weighing little more than one pound is worn by each miner throughout the entire shift and is powered by the miner's cap lamp battery. After this integration period, the unit is connected to a reading network whereupon the day's data is dumped, calculated and stored. Beginning in July 1980, prototype units were subjected to vigorous underground testing in uranium mines in Canada and the United States and in tin mines in Cornwall, U.K. The testing results are summarized and proposals advanced for a typical mine monitoring system utilizing the alphaDOSIMETER.

Jan 1, 1981

By Jerry L. Taylor

Utah Power & Light Company is an electric utility serving approximately 1.8 million people in Utah, Idaho, and waning. In order to supply coal to fuel power plants, Utah Power & Light awns three mines in central Utah. Planning for these mines is aided by a computer program developed by the staff mining engineers. This program, when supplied with the pertinent seam and mining configuration data, calculates the time to mine each section. This allows the planning engineer to estimate accurately the time required to extract pillar sections or develop longwall panels. The program's greatest benefit, however, is its ability to allow the engineer to examine quickly, different combinations of possible mine layouts to determine the most efficient plan. Computer aided mine planning has been used at Utah Power & Light Company since 1979, and has significantly improved the accuracy and quality of mine planning.

Jan 1, 1983

By J. M. GLEDHILL

(Washington Meeting, May, 1905.) A Discussion of Mr. J. M. Gledhill's paper, read by title at the Lake Superior meeting, but presented first at the New Yolk meeting of the Iron and Steel Institute (October, 1904), and here published under a mutual agreement. Between the two Institutes. Discussion. MR. E: WINDSOR RICHARDS, Past-President, said that at a recent meeting of the Institution of Mechanical Engineers a paper was read on tool steel, and he called the attention of the members to the high-speed tool steel at the Bethlehem Works. They would have the pleasure of seeing those wonderful works and would see 60, 70, 80 and 100 tons oil lathe with half-a-dozen of these high-speed tools running. PROP. H. M. HOWE (Columbia University) said that they all looked upon these high-speed tool steels as of very great importance, particularly to the machine shop. One point occurred to hire : Had it really been shown that Swedish steel is necessary, or better than equally pure steel that is not Swedish; and is cemented steel really necessary, and is there any advantage in using that, rather than equally pure open-hearth steel'! It might be well if the author could indicate the kind of evidence on which lie bases his assertion that it is necessary to have cemented Swedish steel. Many were hoping for the development of high-speed steels from elements which exist in great quantities, such as silicon, manganese and chromium, rather than from rarer metals like molybdenum, vanadium and tungsten, the supply of which is likely to be soon exhausted. If the high-cutting speed was to last more than a generation, it. seemed to him that they would have to draw upon the common ele¬ments and not upon the rare ones. MR. Tom WESTGARTH (Middlesbrough) said he fully appreci¬ated what had been said about the advantages of using high-speed steel, because great benefit had been derived from the

Mar 1, 1905

By J. M. GLEDHILL

IT would doubtless have been felt by many but a few years back that there was little left to be said on the subject of crucible tool-steel, and that something akin to finality had been arrived at in its manufacture and general treatment. Probably such feeling was justifiable when it is remembered that the making of steel in crucibles is by far the oldest method known, dating back from time immemorial, it being indeed impossible to accurately trace its origin and earliest development; but it seems certain that carbon-steel was made and used thousands of years ago for cutting-tools. Proof of this may be seen by the marvelous carvings and workings on the intensely hard stone-work of the ancients, for it would be difficult to conceive by what means, other than with steel tools, such work could have been executed; and it is wonderful to contemplate that steel cutting-tools should have been used so long ago, whilst the principle of manufacturing them-that is, by fusion of iron and charcoal in crucibles-was then in a measure on the sane lines as we work on at the present day. Archaeologists have discovered that the Chinese made steel in crucibles long before the Christian era. " Wootz " steel fabricated in India centuries ago was crucible steel, as was also the celebrated Damascus steel, produced at the forges of Toledo, and, curiously, this latter steel furnishes' yet another proof that "There is nothing new under the Sun," for it is recorded that Damascus steel contained certain percentages of tungsten, nickel, manganese, etc., some of the very elements, in fact, contained in the present modern high-speed steel, so that a latent high-speed steel may be said to have existed

Mar 1, 1905

By Terence G. McCusker

Precast concrete segmental tunnel linings have been used since at least 1903. More serious attention was devoted to them in England during the World War II steel shortage and they have become increasingly common since that time. They are now coming into common use in the United States, especially as primary linings for soft ground tunnels and for rock tunnels in poor ground, although they have also been used as final lining, especially in rock tunnels. The developmental logic, design considerations, and current practices are examined. Particular attention is given to unbolted linings, with and without secondary linings. Probable future developments are considered.

Jan 1, 1989

By Paul Cartwright

A rockbolted roadway risk assessment procedure has been developed specifically for the Parkgate seam at Thoresby Colliery by Rock Mechanics Technology and colliery engineers. The purpose of this assessment is to identify any areas of significant risk in relation to roof instability due to potential failure or overloading of the rockbolt support system. This allows appropriate additional support to be installed in sections of roadway considered to be at increased risk. The assessment of risk in rockbolted coal mine roadways, in terms of fall of material, has to be based on an understanding of the rock mass behaviour at that site. The development of an appropriate risk assessment system is therefore site specific. A consistent approach to developing such a system can, however, be applied by adopting the same general logic to each individual site. The use of risk assessment to categorise areas with increased risk of roof instability has been undertaken for four longwall panels at Thoresby. The procedures used for these assessments are discussed and the operational benefits examined. The approach successfully used at Thoresby has been developed into a routine tool to assist mine personnel in assessing areas of potential roof instability in rockbolted roadways and as a means of communicating the position of these areas to both supervisors and workmen. The system provides a rational and objective interpretation of the current underground conditions based upon a logical, consistent and structured approach.

Jan 1, 1999

By V. Srajer

The Calgary Coal Research Laboratory of CANMET and the National Research Council in Ottawa are developing a series of computer models aimed at improving productivity and operational practices of the Canadian surface coal mining industry. One of the top priorities in this respect is a comprehensive computer model of truck/shovel system. A total of twelve mining companies supplied data for validation purposes. The supplied data, operating practices and variances of individual mining systems from the general version of the computer models are discussed in the paper. A short overview of the truck/ shovel model and a plan for future activities involving the application of the computer models for simulation of mining practices are also described. The presented paper summarizes the experience gained during the collection of data for the development and validation of the model.

Jan 1, 1986

By Lawson J. Taylor, Paul N. Worsey

Recent reputable evidence conclusively indicates that conventional chemical delay elements in delay detonators are notoriously inaccurate and can thus seriously affect blasting efficiency.

Jan 1, 1983

By Bo Feng

The development of surface charge of serpentine mineral and implications for sulphide ?otation have been studied through flotation tests, sedimentation tests, zeta potential measurements and optical microscope photos. The results show that the serpentine mineral was positively charged at an extensive pH range, with an isoelectric point (IEP) of 11.9. The magnitude and sign of the pyrite particles were pH dependent and were negative for pH values above 2. At pH value 9, where ?otation of nickel sul?de ores is routinely performed, serpentine and pyrite particles attract through an electrostatic mechanism. Slime coatings of serpentine adhere to the surface of pyrite, reducing pyrite flotation recovery. The removal of magnesium ions from the serpentine surface by acid leaching results in a decrease of serpentine IEP and eliminates the adverse effect of serpentine on pyrite flotation. Therefore, it has been clearly established that the surface charge value developed in the serpentine/aqueous electrical interface is a function of the serpentine surface incongruently dissolution. As a result of hydroxyl dissolution, the magnesium ions are left in serpentine surface, which is responsible for serpentine surface charge. The methods, which can remove magnesium ions from serpentine surface, can be used to eliminate the adverse effect of serpentine on pyrite flotation.

Sep 1, 2012

By G. Gafner

The paper gives the reasons for the development of a gold alloy of 990 fineness with good colour, durability, and mechanical properties, and explains why titanium was chosen as the alloying metal. Methods are described for the alloy?s production, solutionizing, and age-hardening. Mechanical properties are given as a function of deformation, age-hardening time, and temperature for three different starting states, and these properties are compared with those of some standard 14 and 18 ct jewelery alloys and pure gold. The effects of various salts and fluxes on the composition of the alloy after heat treatment at 1150, 800, and 500°C are discussed. These indicate how alloy scrap can be refined to pure gold, and how solutionizing and agehardening can be conducted without the use of vacuum equipment. The results of wear tests indicate that the alloy is more durable than normal coinage and jewelery alloys. Tips are given on the grain refining, soldering, and casting of the alloy.

Jan 1, 1989

By Gill L. F, Gleeson HB

This paper describes the development of a Computer Aided Design and Drafting based mine planning system in the State Electricity Com- mission of Victoria. The system combines a commercially available CADD system with a commercially available mining/geological package. The methodology used in the establishment of the combined system, the fea- tures of the system and the current status of development are discussed.

Jan 1, 1989

By A. Mehmet

The feasibility of employing a multi-stage column for the recovery of gold from cyanided pulps using extruded carbon was investigated on a pilot-plant scale. It was anticipated that the column contactor would have certain advantages over conventional carbon-in-pulp plants. The feed pulp was screened to remove particles larger than 200 µm and was diluted to a solids concentration of about 23 per cent. The column was operated continuously for 24 days at a pulp flowrate of about 60 l/min and a carbon flowrate of 44 litres per day. The average gold concentrations in the barren pulp 12 hours and 24 hours after the carbon transfer were 0,012 and 0,031 mg/l respectively. The average gold concentration in the solution phase in the feed was about 2,0 mg/L. The average gold Loading on the carbon was 6290 g/t. Calcium carbonate was removed from the loaded carbon by treatment with 0,5 bed volumes of 2,8 per cent hydrochloric acid solution at ambient temperature. The calcium concentration was reduced from about 17 000 to about 500 g/t The carbon was eluted by the Zadra procedure at atmospheric pressure. The results of the elution were highly satisfactory, the gold concentration being reduced from about 6000 to about 20 g/t in 48 hours. The eluted carbon was regenerated in a Rintoul kiln at about 700°C. The activity of the regenerated carbon was found to be at least as high as that of fresh carbon.

Jan 1, 1992

By J. D. Stone

This paper briefly reviews the adequacy of existing management theories and practices and the managerial proficiency or competency in the South African mining industry. The investigation revealed that existing management practices are totally inadequate to enable all employees on all the levels of the mining industry to achieve the results required from them, in all aspects, at all times. As a result, the South African mining industry is gradually losing its long standing reputation as a relative cheap, competitive, and reliable supplier of minerals to the local and global markets. According to some prominent management authors and theorists, an all-inclusive unified management theory does not exist at present. In this paper the authors summarize the main aspects of a newly developed comprehensive, practical, and integrated management method. It is believed that the application of this method would significantly improve the future performance and competitiveness of the South African mining industry

Jan 1, 2010

By Peter N. Calder, Louise H. Michaud

"An interactive mine planning package has been developed to aid with the tasks involved in generating dragline mine plans. This package employs recent advances in PC-based,3D computer graphics and 3D geologic modelling. A Gridded Seam Model (GSM), capable of modelling rugged topography and multiple coal seams, including folding and faulting, is used to generate the geologic database This model is then integrated with an interactive graphics mine planning system in order to develop one model and one database for the generation of the mine design, the depletion of the coal reserves and the removal of waste material.As well as offering large potential saving in the time required to carry out the planning tasks, the system offers immediate visual feedback to the planning engineer. This can greatly aid in the conceptual understanding of complex geology and mine plans and can allow for the evaluation of a number of mining options within a reasonable time frame.IntroductionThere are a large number of variables that must be taken into account during the development of a dragline mine plan. This is especially true when developing a mine in mountainous terrain, where there is a lack of continuity of the geology and topography over the mine site. Until recently, the complexity of dragline mine plans has prohibited the development of a universal mine planning package that is applicable to all geologic and topographic situations. The majority of the commercial programs that are presently available to facilitate dragline mine planning have been developed for specific mine properties or are limited in the coal geology and mining methods that they can simulate (Brown and Clifford, 1983; White 1983; White and Jones, 1984; Sadri and Lee, 1982; Dagdelen, 1979)."

Jan 1, 1993

The first stage in the refining of lead blast furnace bullion is the removal of copper and this is normally done as a batch process in open kettles,A number of attempts have been made in the past to establish fontinuous processes operating in reverberatory type furnaces, but the growth of accretions in the furnace has always presented a serious problem.This has been overcome in the plant of the Broken Hill Associated Smelters Pty Ltd at Port Pirie by the construction of a reverberatory furnace and ancillary cooling system of novel design.Although a number of mechanical and metallurgical problems still remain to be solved, it is claimed that a workable continuous copper drossing process has been established.

Jan 1, 1963

The first stage in the refining of lead blast furnace bullion is the removal of copper and is normally done as a batch process in open kettles.A number of attempts have been made to establish continuous processes operating in reverberatory type furnaces, but the growth of accretions in the furnace has always presented a serious problem.The Broken Hill Associated Smelters Pty. Ltd. (RH.A.S.) at Port Pirie have overcome this problem by constructing a reverberatory furnace and ancillary cooling system of a novel design.Although a number of mechanical and metallurgical problems still remain to be solved, it is claimed that a workable continuous copper drossing process has been established.INTRODUCTIONLead bullion emerging from the blast furnaces at Port Pirie is at a temperature of about 1100°C and contains, among other impurities, about 1 per cent of copper.The first stage of refining is the removal of this copper by a drossing operation and in the past this was done, batchwise, by allowing the bullion to cool back in 100 ton kettles.At about 700°C, copper dross begins to separate as a crust on the surface of the kettle and this separation was allowed to continue down to about 450°C when the crust was brokenup and skimmed manually using a long handled, balanced, spoon. The dross was then smelted in a reverberatory furnace to produce a saleable copper matte and separate out lead bullion, which was returned to the drossing kettles. The copper content of the drossed bullion was then further reduced by a sulphur treatment process.The drossing operations involved hard manual labour under arduous conditions and the pouring of hot bullion into...

Jan 1, 1963

By D. Visser, P. D. Toens

The development of a continuous recording scintillation counter mounted on a cyclometer by P. D. Toens (Fellow) and D. Visser (Visitor) In order to facilitate ground radiometric surveys the Atomic Energy Board has developed a continuous recording device attached to a scintillation counter which is mounted on a cyclometer. Details concerning the construction are given.

By M. J. Lottering

Gold deposits in South Africa are invariably associated with uranium bearing minerals. Although it is low grade uranium by international standards, averaging around 0.3 kg U3O8 per ton of ore, recovery of uranium as a by-product improves the overall economics of gold extraction. Moreover, the current high uranium prices as well as increased demand due to renewed interest in nuclear power provide significant incentives for dedicated uranium production. An understanding of the uranium leaching response to changes in operating conditions is an important first step to-wards optimisation of uranium recoveries. In South African acid leaching plants, uranium dissolutions higher than 90% are difficult to achieve, and the chemical origin of this limit is not clear. To study leaching behaviour, an important consideration is the mineralogical characteristics of the ores. Typically, a diagnostic leaching approach can be followed. In this paper, a mineralogy-leachability explanation is presented to rationalise the difficulty in exceeding 90% dissolution from low grade uranium ores on the basis of a simple diagnostic leaching method. It was found that brannerite was the main reason for the existence of a dissolution limit in Witwatersrand ore and that chemical liberation was more effective to increase end dissolution compared to physical liberation. The findings from these investigations will form guidelines for developing economically viable flow sheets for improved uranium recovery, at least in a South African (Witwatersrand) context.

Jan 1, 2014