Search Documents

By D. Duncanson, R. J. Davidson, C. G. S. Schmidt, G. A. Brown, J. D. Taylor, N. W. Hanf

The development of a cyanidation route for the treatment of gold-plant gravity concentrates is described. This work was carried out as a natural consequence of earlier improvements to the recovery of gold in the gravity sections of existing gold plants. Concern about the environmental aspects of the conventional amalgamation process was further motivation in the development of an alternative procedure. It was found that the partial pressure of oxygen in solution was the most critical reactionrate determining factor. The rate of gold dissolution was shown to be controlled by the reaction rate below approximately 25°C and by diffusion above that temperature. Thus, the efficiency of pulp agitation and oxygen partial pressure permitted a high degree of control over the rate of gold dissolution. The use of oxygen rather than air significantly increased the dissolution rate of both gold and silver. The solubilities of sodium, calcium, and potassium aurocyanide complexes under simulated reaction conditions were studied, and it was established that the values for the sodium and calcium complexes were limited, requiring the use of lower pulp densities and higher reaction temperatures for the treatment of very high-grade concentrates. The presence of excessive amounts of tramp iron in such concentrates of up to 25 per cent by mass was found to result in poor gold dissolution owing to the cementation of gold under certain reaction conditions. The maintenance of high oxygen partial pressures, together with high cyanide concentrations, high pH levels, and the presence of calcium in the system, all aided in passivating the tramp iron. Copper, gold, and iron were shown to be the main cyanide-consuming elements. Optimum gold dissolution was obtained in a closed bench-scale reactor incorporating a flotation-machine type of agitator for effective pulp agitation and oxygenation, the oxygen being recirculated. The reactor was designed to operate under a very small positive pressure. After reaction times of 2 to 6 hours at temperatures in the region of 30°C, both the gold and the silver dissolution averaged 99,S per cent. In the case of very high-grade concentrates, it was shown that gold could be floated in the same reactor by drawing off the flotation concentrate through a port in the reactor. A flotation recovery of 87,4 per cent of the gold in 3,9 per cent by mass was obtained. The recovery of osmiridium from cyanide-leach residues and the electrowinning of gold from the pregnant liquors were also considered as processing aspects in the treatment of gold-plant belt concentrates. Final table tailings with a gold concentration of 10to 12 gft were obtained. The results of the investigation strongly suggested that an alternative cyanidation route for the treatment of gold-plant concentrates was technically feasible, provided the system included effective agitation and oxygenation. In the case of lower-grade concentrates, cyanidation followed by the electrowinning of gold appears to be the simplest route, while, for high-grade concentrates, flotation and smelting of the concentrate followed by cyanidation of the flotation tailings are suggested. The use of oxygen rather than air for sparging the pulp would depend largely on the grade of material to be treated. A preliminary comparison of the costs related to the amalgamation and cyanidation processes for the recovery of gold from such concentrates indicated very similar capital and operating costs. It was concluded that other considerations, e.g. toxicity, safety, and lower labour requirements, were more important than such small cost differences. Furthermore, the 'opening' of the gold-plant gravity circuit, which would be made possible by a cyanidation route, would further reduce the operating costs because of the subsequent decrease in the tonnage to be treated.

Jan 1, 1978

By McKee D. J

Much research is aimed at providing a revolutionary advance in technology that has the potential to render current mining and beneficiation problems obsolete. Such revolutionary advancements have been significant but few in number. Recent history shows that most improvement has been derived from a series of incremental improvements to the many processes that make up mining and beneficiation systems. Management approaches are changing to encourage this 'continuous improvement' and to support its implementation through the formal management of quality. This paper reviews some of the industry's priority R&D project areas and demonstrates that very significant opportunities are available to broaden the focus for improvement from individual processes to include the interaction between mining and mineral beneficiation systems.

Jan 1, 1994

By Dundon P

The Broken Hill Proprietary Company Limited (BHP) is Australia's largest company with widespread commercial interests ranging from steel productin to minerals, oil and gas recovery. While these interests are worldwide, the Company operates or is partner in more than 30 Australian mining ventures. BHP Engineering (BHPE) is the in-house consultant to BHP but is also the largest consultancy in Australia available to general industry. Australian Groundwater Consultants Pty Limited (AGC) is a large, independent consultancy offering specialist services in all aspects of water resources, waste management and environmental engineering, both in Australia and overseas. AGC is particularly well regarded within the mining industry and has a considerable record of providing solutions for mine water related issues. By drawing on the extensive combined experience of AGC and BHP Engineering, this paper will summarize some of the unique ways in which water interacts with and impacts on mining operations in Australia, particularly in matters such as: Slope Stability Drainage and Dewatering Production Cost (Transport, Drilling, Blasting, etc) Water Supply Water Management Tailings and Waste Management Environmental Issues. The paper will also illustrate the cost benefit of providing major engineering works for reduction in total mining cost. It will be shown that, through advance planning and close interaction between outside experts (ie consultants) and on- site personnel, very significant operational cost savings can be made while at the same time achieving a safe and responsible mining environment.

Jan 1, 1988

By Abdalla MH

The deformation resulting from the presence of a tunnel may signifcantly affected, nearby structures and need to be considered during design of both tunnel and structure. The aim of this paper is to study the effect of different factors which may affect the interaction between the tunnel and the str- ucture. These include; the depth of both tunnel and foundation level of the structure ( z and t ), distance between C.L. of tunnel and loads, breadth of the loaded area, Diameter of tunnel and lining of the tunnel. The problem is studied as a two dimensional plane strain model by the boundary element technique. The results of this study indicated that the presence of a cavity/tunnel increases, in general, the vertical displacement on the ground surface and at the foundation level as well as the horizontal and vertical stresses in the cavity/tunnel level. The effect of eccentricity is increasing as e/D decreasing. For pile foundation there is a quite different- influence of the presence of cavity/tunnel in both cases of friction pile and end bearing pile type of foundation.

Jan 1, 1987

By Siyu Song, Yanhong Wang, Guohua Gu, Linbo Huang

In this study, the effect of cations, Na+ and Mg2+, in saline water on copper flotation in the presence of calcium bentonite was investigated. It was found that as the concentration of NaCl was increased, the copper recovery initially decreased and then increased to above 99%, while the copper grade initially increased and then decreased. In contrast, as the concentration ofMgCl2 was increased, the copper recovery continuously increased, while the copper grade continuously decreased. The variation of copper recovery and grade was mainly attributed to the synergistic effect of pulp rheology and flotation solution chemistry. The underpinning mechanisms are the compressing electrical double layer and ion-exchange interaction between saline water and bentonite, which occur at the same time. Using salinewater slightly affected the pulp rheologywith a decrease in copper recovery at low NaCl concentration. Increasing the concentration of cations in saline water might even facilitate the flowing out of exchangeable cations, especially divalent cations, from the interlayer space of bentonite to the solution, resulting in the decrease of copper grade at high salt concentration.

Sep 10, 2020

By V. Jovicic, J. Likar

The knowledge of the geological sequence and hydrological conditions in the area of portals was the basis for the design of the entry of the highway into tunnel Trojane. Mudstone, claystone and sandstone dominate the rock layering, which is tectonically reworked and contains structural anomalies. The complexity of the sequence makes it impossible to survey all the relevant features along the full 3km length of the tunnel. Sudden and frequent transitions between litological sequences impose potential instabilities and make the excavation of the tunnel particularly difficult. The initial survey established the zones of potential failures. These were monitored using topographic survey and inclinometers with an aim to make further geotechnical analyses more reliable and adjusted to the ground conditions. The analyses of the wall construction and the results of the monitoring showed that the design of the retaining wall was adequate. La connaissance de la séquence géologique et des conditions hydrologiques dans l'aire des portails a été la base pour la planification de l'entrée de l'autoroute dans le tunnel Trojane. Le schiste, l'argilite et le grès dominent la couche rocheuse qui est tectoniquement transformée et contient les anomalies structurales. A cause de la complexité de la séquence, il est impossible de revoir toutes les particularités le long des 3 kilomètres de la toute longueur du tunnel. Les transitions soudaines et fréquentes entre les séquences lithologiques imposent l'instabilité potentielle et font l'excavation du tunnel particulièrement difficile. La revue initiale a été établie sur les zones où il existe l'éboulement potential. Elles étaient contrôlées à l'aide de la revue topographique et de l'inclinomètre pour que les analyses géotechniques suivantes soient plus sûres et adaptées aux conditions du sol. Les analyses de la construction des murs et des résultats du contrôle ont montré que la planification du mur réteneur était correspondante. Der Autobahneingang in den Trojane Tunnel war projektiert auf Basis von der Kenntnis der geologischen und hydrogeologischen Bedingungen in dem Portalgebiet. Das Gebiet besteht aus dem Tonstein und dem Sandstein. Die Schichten sind tektonisch verformt und sind deswegen sehr heterogen. Die anfaenglichen Untersuchungen haben die Zonen von den potentiellen Bruechen definiert. Weitere geotechnische Analysen waren fitted an reale geologische Bedingungen durch das Monitoring der potentiellen Bruchzonen, welches aus den topographyschen Messungen und Inklinometerdaten entstand. Die Analyse des Wandbaues und die Resultate von dem Monitoring haben erwiesen, dass die Wandprojektierung entsprechend war.

Jan 1, 2003

By F. W. Petersen

Slurry reactors are being used extensively throughout the chemical, biochemical and mineral processing industries. This paper describes the interaction between fine ore particles and granular porous adsorbents such as activated carbon and ion-exchange resins in a stirred tank reactor. Gold and silver cyanides were used as adsorbates to detect changes in the mass transfer characteristics of the adsorbents, which were ashed to determine the loading of ore particles. A simple kinetic model incorporating film diffusion, intrapanicle diffusion ~d the adsorption equilibrium, was used to interpret kinetic data and to estimate the effect of slurry conditions on the diffusion parameters. It was observed that the equilibrium loading of fines in the adsorbents was independent of their concentration in the slurry. Furthermore, the presence of these panicles inside an adsorbent decreases the effective diffusion of gold or silver cyanides into the adsorbent matrix. When fine suspended solids are present in the reactor, a decrease in the effective availability of the superficial surface of the pre-saturated adsorbent panicles for mass transfer from the liquid phase was observed. This newly defined surface availability factor was dependent on the concentration, panicle size, and the zeta potential of the fine particles in suspension.

Jan 1, 1993

Stawell Gold Mines Pty Ltd operates two underground decline mines within the township of Stawell. An active exploration program and commitment by owners to improving the ore reserves has led to an improved mine life and reduced operating costs since the purchase of the operation by Mining Project Investors and Pittston Mineral Ventures in late-1992. Over the past six years of operation a cumulative 1 150 000 ounces of gold have been added to the mineral inventory. An improved geological understanding of the orebody has evolved over time increasing the ore reserves and allowing the development of long-term plans for the mines future. This has enabled important capital decisions to be made providing the impetus for improved productivity and thereby reduced operating costs. Co-operative mine planning and mine geology utilising best practice geological systems have enabled the effective extraction of a structurally complex and mineralogically varied deposit within a rural Victorian township. Detailed metallurgical research has improved the function of an aged and poorly designed circuit to boost the mill capacity whilst also improving the metallurgical recovery. The combination of metallurgical expertise and an understanding of the geological setting enable an effective control of metallurgical recovery.

Jan 1, 2000

By Roberts T, Firth B. A

A series of flotation experiments was carried out to study the interaction between the parameters of pulp density (mass per cent of solids in feed slurry) and frother addition (on the basis of solid mass feed rate). It was found that certain combinations of pulp density and frother additions caused large losses in yield. The interactive effect of these parameters can be primarily attributed to the total amount of frother added per unit of water. Consequently it is suggested that frother additions be made on the basis of water flow rate. As frother addition increased, in terms of the amount of frother per unit of water, yield increased rapidly but above an addition rate of about 10 g/tone it reached a plateau. Such results correlated well with qualitative visual observations of changes in bubble size and dispersion, with increasing levels of frother addition.

Jan 1, 1984

By A D. Pradana, D R. Pradana, Y H. Putra, Z Zulhan, T Hidayat

The high temperature processing of nickel laterite ore is currently dominated by the Rotary Kiln- Electric Furnace (RKEF) technology. The ratio of SiO2/MgO (S/M) in the ore is one of the critical parameters that determines the success of the RKEF process. Incompatible S/M ratios in the ore can cause aggressive chemical interaction between the slag and MgO refractory. The slag-refractory interaction at conditions relevant to nickel laterite ore smelting was investigated in the present study. Synthetic mixtures representing the slag compositions of nickel laterite ore smelting were prepared by mixing MgO, SiO2, Al2O3, CaO, Fe2O3, and Fe and heating the mixtures in steel containers at 1300°C under an argon atmosphere for 3 hrs. Pure MgO crucible were used as containment material in the melting process of the mixtures to represent the MgO refractory. The kinetics of the slagrefractory reaction were investigated using samples with selected initial S/M ratios of 2.0 and 3.0 (wt/wt) (with constant CaO = 3 wt per cent, Al2O3 = 5 wt per cent, FeO = 10 wt per cent) by performing melting at 1500°C in MgO crucibles for 5, 30, and 120 mins under an argon atmosphere. The effect of the S/M ratio in slag on the slag-refractory interaction was also investigated by performing melting of mixtures with different initial S/M ratios of 1.75, 2.0, 2.5, and 3.0 (wt/wt) in MgO crucibles at 1500°C for 120 mins under an argon atmosphere. After the melting process, each sample was quenched in water, mounted in resin, ground, polished, and coated. The interaction between the slags and MgO refractory was then evaluated by analysing the polished samples using a scanning electron microscope equipped with an energy dispersive spectroscopy (SEM-EDS). Thermodynamic simulations using FactSage™ 8.0 thermochemical software were performed based on the experimental slag compositions, refractory, and conditions to support the evaluation process. The results show that a higher S/M ratio in slag leads to a higher tendency for the refractory component to dissolve into the slag. A higher S/M ratio in slag also leads to an increasing extent of solid-state diffusion of iron oxide into the remaining refractory grains. The dissolution of MgO into the slag is rapid; the MgO concentration in the final slag increased by 2.4 wt per cent and 5.7 wt per cent at initial S/M ratios of 2.0 and 3.0 wt/wt, respectively, within 5 and 30 mins of the melting process.

Aug 21, 2024

By Johnson N. W, Quast K. B

Over the years there have been occasional references in the literature to the activating effect of cyanide in galena flotation with xanthates. These have usually been associated with the processing of lead-zinc or copper-lead-zinc ores. Bubble contact curves for the pure galena-xanthate system show a flotation edge at pH 10.4 independent of sodium cyanide concentration which was thought due to hydroxyl ion, not cyanide ion.Flotation tests were conducted on samples of Mount Isa lead-zinc ore using varying concentrations of sodium ethyl xanthate and sodium cyanide. At low collector concentrations, galena recovery kinetics improved with sodium cyanide addition, and the higher the cyanide concentration, the higher the galena recovery rate. At higher collector concentrations, galena recovery rate was independent of sodium cyanide addition.For a given collector addition, the lead grade-recovery curve shifted to an improved position with increasing sodium cyanide level. For the same recovery there was an increase in the lead grade with increased sodium cyanide addition, and this increase was most dramatic at high sodium cyanide concentrations.The presence of sodium cyanide during the grinding of Mount Isa ore caused surface passivation of the iron sulphides and possibly the sphalerite.These sulphides, therefore, reacted with less of the oxygen present in the pulp, hence more oxygen was directed to the surface of the galena. This resulted in an enhancement in the total amount of xanthate adsorbed on the galena that is reflected in the improved flotation response of that mineral.

Jan 1, 1990

By Jeffrey N. Schuyler

In order to implement the most efficient and cost-effective hydraulic fracturing stimulation treatment within a particular region, a thorough understanding of the in-situ stress state and rock properties is paramount (Smith et al., 1978; Warpinski et al., 1982). Several studies conducted in order to "characterize" formations have provided invaluable insight into the relationship between lithologic properties, depth, in-situ stress magnitude and hydraulic fracture orientation. These studies have substantiated that at shallow depths, rock properties such as tensile strength and permeability can exert a substantial influence on the geometry of an induced hydraulic fracture. In turn, these "directional properties" can be related to existing geologic conditions during the time of deposition or major diagenetic alteration of the rock body. As the depth of the "payzone" increases, the role of the in-situ stresses and therefore the prevailing tectonic conditions becomes the dominant factor in determining fracture geometry. However, reservoir properties cannot be ignored. The porosity, permeability, pervasive fabric element and directional elastic properties can have a significant influence on the success of those tests conducted to measure the in-situ stresses either directly or through secondary observations... for instance, pore-pressure effects on measurements of in-situ stress. The purpose of this paper is to provide, through the use of appropriate field and laboratory examples, a more thorough understanding of in-situ stresses, rock properties and their integrated effect on hydraulic fracture properties. In addition to highlighting and expanding the wide body of existing literature, the case studies cited are designed to encourage mutual transfer of technology from petroleum-related, rock-mechanics efforts to other disciplines.

Jan 1, 1984

By R. R. Klimpel

This paper demonstrates, using the results of an unusually complete industrial test sequence, what the various interactions are between grind size, collector dosage, and frother type. While particle size is universally acknowledged to be important in optimizing industrial copper sulfide rougher flotation circuits, many of the various interactions that do occur at the industrial level with particle size are still being identified and/or quantified. This study also presents, in a consistent manner, the changes in flotation kinetics that occur as a function of particle size, in a typical industrial circuit along with some insights as to how flotation operators can optimize rougher circuit performance.

Jan 1, 1993

By Sonia Helle, Ursula E. D. Kelm

"From a metallurgical point of view, acid leaching of oxide zone copper ore is considered in the first place in terms of ore grade, whole rock mineralogy, rock granulometry, crushed aggregate size distribution, porosity, permeability and corresponding fluid flow characteristics. Despite exhaustive physicochemical and general mineralogical characterization, drops in copper recovery occur and are often attributed to and “unquantified mineralogical misbehaviour” of the gangue phases. This study establishes an experimental link to monitor and quantify the chemical interaction of chrysocolla, malachite and atacamite with reactive gangue phases.Laboratory-scale sulphuric acid (15%) leaching in small columns is carried out using a synthetic rock composed of 57% quartz, 1% ore phase, and 42% reactive gangue. Gangue phases were selected to represent mineralogy found in argillic, advanced argillic, and propylitic alteration zones. Exotic copper ores of Codelco Norte (in particular Mina Sur) served as model for the modal distribution of mineral phases. Natural reactive gangue phases (<200 Tyler mesh) were chosen as pure as possible: Saz-1 and Swy-1 montmorillonites, KGa-1B and KGa-2 kaolinites (all Clay Mineral Society, USA, Source Clays) Nau-2 nontronite, Imt-1 illite (both Clay Mineral Society Special Clays) and Chilean mordenite, laumontite and bentonite. Ore phases are: mineraloid chrysocolla from Radomiro Tomic (Codelco Norte), reagent grade malachite and a purpose synthesized atacamite-paratacamite mixture. Complete chemical, physicochemical and mineralogical characterizations were carried out for ore and gangue phases.The following observations hold for samples with and without mineralization: Smectite-rich gangue increased up to 75% in volume. Once wet, air-filled vesicles formed due to the rapid sealing effect of overlying smectite in the column. No volume change occurred for illite, mordenite and kaolinite gangues. For kaolinite mixtures acid puddles formed on top of the column during initial leaching due to the delamination and barrier formation of this phyllosilicate. Fluid recovery was <60% for expandable phases and reached up to 80% for non-expandable mixtures. These observations confirm the very low extractions obtained in ore with a combined smectite – kaolinite gangue for Mina Sur. The most important mineralogical changes observed in the solid residues are: reduction of basal smectite phase reflections (XRD), and slight loss of illite intensities. This is also reflected in the major element composition of the residues, which demonstrate a loss of Mg, Mn, Ca, Na, K followed by Fe, Al and Si; with their proportions depending on the starting materials. Furthermore, alunogen and meta-alunogen formed, with related phases coquimbite (illite) and godichite (nontronite) also depending on gangue mineral chemistry. For laumontite samples, meta-alunogen and alunogen precipitated from the leachate."

Jan 1, 2003

By Filmer AO

In contrast to the &apos;50s and &apos;60s, the period of the &apos;80s and &apos;90s seems likely to have low growth in demand but much greater levels of technological change. In such a climate there will be pressure on costs, productivity will continue to rise and competitiveness will be closely associated with maintenance of the most effective technology. The penalties for inappropriate investments, whether short sighted or mistakenly based on a particular view of the future, will be greatly enhanced. Accordingly, there will be a need for significantly improved anticipation of technical change and thus for better planning. Study of the funding and direction of the world&apos;s R&D effort can provide a useful input to the planning processes within industries and individual firms. Such a study also suggests some insights into the characteristics of those countries which have achieved substantial growth and high standards of living over the past two decades. These characteristics may offer significant reminders for our own development. The particular implications for the Australian minerals industry include the need for direction that is sensitive to changing market requirements and customer practice. This is not simply "more of the same." In particular it appears essential for both basic and applied R&D to provide a sound basis for the purchase and ongoing development of the new technology required to achieve international Competitiveness.

Jan 1, 1986

By R. Katzenbach, M. Vogler, U. Adamietz

Abstract The design of deep excavation pits in rock mass is dependent as well on the mechanical properties of the rock mass as for example the orientation and the type of discontinuities like bedding planes, joints and fissures, the length of the discontinuities (persistence), the grade of weathering, the strength of rock mass, and the shear strength in the discontinuities, etc., and also on the respective boundary conditions specific for the project, and here especially the geometrical boundary conditions. The basic mutual influences and interactions between these boundary conditions are explained and exemplary presented at an excavation pit with a depth of 18,5 m, situated at a slope with a surface near groundwater table. Résumé La planification des excavations profondes dépend aussi bien de la qualité mécanique du roc, par exemple la location de la texture de la surface de moindre résistance, le degré de rupture, le degré de décomposition, la dureté du roc et la résistance limitée au cisaillement de la texture de la surface de moindre résistance que des conditions limitées spécifiques pour le projet, ici en particulier des conditions limitées géométriques. Les influences et interactions essentielles et mutuelles entre les conditions limitées isolées seront expliquées et présentées à l’aide d’une excavation 18,5 m de profondeur, située sur une pente où le niveau des eaux souterraines est près de la surface. Kurzfassung Die Planung tiefer Baugruben im Fels hängt sowohl von den mechanischen Eigenschaften des Fels wie z.B. der räumlichen Lage des Trennflächengefüges, dem Durchtrennungsgrad, dem Verwitterungsgrad, der Gesteinsfestigkeit sowie der Scherfestigkeit des Trennflächengefüges als auch von den projektspezifischen Randbedingungen hier insbesondere von den geometrischen Randbedingungen ab. Die wesentlichen gegenseitigen Einflüsse und Interaktionen zwischen den einzelnen Randbedingungen werden aufgezeigt und an einer 18,5 m tiefen Baugrube in Hanglage mit oberflächennahem Grundwasser vorgestellt.

Jan 1, 2003

By J. M. Paull, J. B. See

The rate of reaction between different carbonaceous reducing agents and silicon monoxide gas was studied by the use of a technique developed in Norway by Tuset and Raaness. Argon carrier gas was used to pass a known fixed concentration of silicon monoxide gas through an I1 cm3 sample of precalcined reducing agent at 1650°c. Silicon monoxide gas was generated by the heating of a mixture of silica and silicon carbide, and the progress of the reaction was followed by monitoring the carbon monoxide in the off-gas with an infrared spectrometer. The reactivity of silicon monoxide gas towards a number of carbonaceous reducing agents (charcoal, Iscor coke, Lurgi char, and petroleum coke) was shown to be similar to results obtained with the carbon dioxide reactivity test. The silicon monoxide reactivity test was able to indicate the extent to which fines were generated when the reducing agent was converted to silicon carbide. Of the reducing agents studied, Lurgi char appeared to be the most suitable for the production of ferrosilicon because it has a high reactivity towards silicon monoxide gas and high strength when converted to silicon carbide. So that industry could be given some indication of the suitability of certain reducing agents for the production of ferrosilicon and silicon metal, a reactivity scale similar to that of Tuset and Raaness was constructed that compares the volume of silicon monoxide gas required by a reducing agent to reach a carbon monoxide content of 10 per cent in the off-gas during the conversion of the reducing agent to silicon carbide. This scale assists in the selection of those reducing agents that require less silicon monoxide gas for conversion to silicon carbide, and that give savings in material and power costs because less silicon monoxide gas need be generated in the furnace.

Jan 1, 1979

By Ahmad Ghahreman, Lin Li

Silver and cupric ions have been proven to play the roles of catalysts to promote the oxidation kinetics of chalcopyrite in acid solution. In this study, the interaction between silver ions and cupric ions during ferric leaching of chalcopyrite in sulfuric acid solution has been investigated. The electrochemical study by Tafel analysis showed a significant boost of dissolution rate for chalcopyrite dissolution in Fe3+- Cu2+ containing sulfuric acid solution after Ag+ was added in the solution. For 10 ppm Ag addition, the dissolution rate of chalcopyrite increased to 7.94 ×10-6 A/cm2 from 3.2 ×10-7 A/cm2, when Ag+ was absent. On the other hand, the effect of Cu2+ on the dissolution of chalcopyrite in Fe3+-Ag+ containing sulfuric acid solution was not obvious from electrochemical measurements. The chalcopyrite leaching tests in different acid solutions showed that silver addition had an obvious catalytic effect on promoting chalcopyrite dissolution. Comparing the leaching rates of chalcopyrite leached in Fe3+ containing, Fe3+-Ag+ containing, Fe3+-Cu2+ containing and Fe3+-Cu2+-Ag+ containing sulfuric acid solutions, it was found in Ag+-Fe3+-Cu2+ containing sulfuric acid solution, the leaching rate was highest among all the aqueous acid systems. Further leaching tests suggested that with increase of the Ag+ concentration from 0 to 20 ppm, the leaching rate of chalcopyrite in Ag+-Fe3+-Cu2+ containing sulfuric acid solution also increased and reached 57.62% with 20 ppm Ag+ addition after 24 h. INTRODUCTION Chalcopyrite is the most important copper mineral in copper hydrometallurgy and it accounts for nearly 80% of the universal copper resource (Olvera, Rebolledo, Mora, Dixon, & Asselin, 2018). The hydrometallurgy of chalcopyrite has been intensively studied with emphasis on solving the slow dissolution kinetics of chalcopyrite in acid environment. A variety of aqueous systems, such as sulfate (Hiroyoshi, Miki, Hirajima, & Tsunekawa, 2001), chlorides (Liu, Chen, & Yang, 2017), and ammonia (Hua et al., 2018) have been studied to improve copper leaching. From another perspective, chalcopyrite leaching studies have indicated that the mechanism of chalcopyrite dissolution in acid solution is essentially electrochemical (Li, Kawashima, Li, Chandra, & Gerson, 2013). Therefore, extensive studies have recently been carried out to explain the dissolution kinetics of chalcopyrite in different media by various electrochemical techniques.

Jan 1, 2019

By M. J. Gilbey

Cross passageways between adjacent tunnels in passenger rail or transit systems may be used during train fire emergencies to evacuate passengers to points of safety in the non-incident tunnel. Rescue trains can be brought into the non-incident tunnel to remove passengers to expedite evacuation times as compared to walking along bench walls to the nearest egress stairs. In cases of multiple train emergencies, the required ventilation capacities can result in high pressure differences between the incident and non-incident tunnels. These pressure differences can make it difficult or impossible for a normal person to open doors of a cross passageway between adjacent tunnels. If opened, the velocity of the airflow through an open cross passageway can reach levels high enough to impede passenger evacuation. This paper describes the analysis of this problem for a sample rail tunnel. A ventilation concept that mitigates the problems of high cross passageway door opening forces and high velocities through open cross passageways is presented.

Jan 1, 2009

By Anthony T. Iannacchione

This study, funded by the Appalachian Research Initiative for Environmental Science (ARIES), examines how mine layout, mining method, and geology interacted to allow water from the Grove No.1 mine pool to discharge into local surface waters. Federal and State regulations prohibit the discharge of acid or iron-producing waters from underground coal mines. Mining companies design barriers around their operations to prevent mine waters from discharging to the surface. The Grove No.1 represents one mine where these designs proved inadequate. Unique geologic conditions at the Grove No.1 mine pool, combined with retreat room-and-pillar mining, contributed to a discharge that required passive water treatment.

Jan 1, 2013