Search Documents

By P. Tapp, T. Evans, N. A. Molloy, J. Lucas

"Consideration of the protoype tuyere geometry for injection of inert gas through the bottom in a basic oxygen steel furnace and a requirement to specify an optimal flow for bottom wear and metal penetration led to experimental investigations[l,2] to apply the results of previous workers to this specific case, Flow velocity profile development within the tuyere was proposed as significant and the experimental scheme was designed to test this. It is proposed that the design criterion for the conditions of optimal flow of the prototype geometry be based on the non-dimensional mass velocity.INTRODUCTIONSharma[3] tested small diameter tuyeres in a laboratory hot model using molten iron to define a flow criterion for prevention of penetration of the bath liquid into the tuyere. Using argon, nitrogen and helium through a range of tuyeres (1 to 3 mm ill ) he proposed the jet Froude number C Fr' ) with the critical value being 2400 - 2500 or higher. Sonic or supersonic velocity was not a sufficient criterion. The tuyere design was a parallel tubular duct of moderate aspect ratio CAR) i.e. the ratio of length to diameter ranging from about 22 to 36 in the experimental furnace.Farmer et al[4] stated their their aim ""to develop a unifying explanation and procedure for the proper design of tuyeres"" but disagreed with Sharma's jet Froude number criterion. Recalculating Sharma's data they proposed instead a fully expanded Mach number of 1.75 with an initial expansion angle of ten degrees as the lower bounds of flow to meet the design requirement. They experimented with tuyeres in a water model using tubular, annular and convergent-divergent nozzles. The aspect ratio of the parallel duct tuyeres was from 533 to 762 using diameters of 1.4, 1.7 and 2.0 mm C the diameters being of tubes to be used full scale). Subsequently these results were applied to a prototype tuyere using a diameter of 1.7 mm with beneficial results in practice. This tuyere had an aspect ratio of 1067."

Jan 1, 1996

By M. Kreuh

An investigation of the pressure pulse spectrum generated by the gas dispersion processes in a Peirce Smith copper converter was undertaken via the simultaneous measurement of four tuyeres using high frequency pressure transducers. The data was captured, stored, and analyzed using digital data processing techniques; including power spectral density plots, band-pass filtering, and a principal component analysis (PCA). The process was characterized throughout by a dominant 3 Hz pulse signature attributed to the formation of lateral gas envelopes. In particular, test tuyeres in the tuyere line tended to operate synchronously at the dominant frequency, regardless of operating conditions tested and despite being distributed along the converter. Synchronous behavior is thought to arise from the acoustic coupling and possible resonance behavior of the gas delivery system on the converter.

Jan 1, 2007

Closed-circuit television was first installed under- ground by United States Steel's Tenessee Coal & Iron Division during the summer of 1957. Placed at a rotary dump location in one of TCI's mines, the installation was designed to permit operation of all functions of the load car haul chain, rotary dump, and empty car haul chain from a remote location, and to improve safety. The initial installation was very successful, and similar ones were subsequently placed at all of TCI's operating ore mines. The 10-ton capacity, automatic coupled mine cars are placed on the load car haul chain by the main-line locomotives. The haulage dispatcher has been located at the skip loading point of the underground pocket, some 80 to 100 ft below the rotary dump. The video monitor is located so the operator has a constant view of the activities around the rotary dump. By means of remote controls, the TV camera can range through a four-way turret of lens changes, can pan 350° in about nine seconds, can tilt 45° up or 45° down in nine seconds, and also can range through an optical focus for any of the lens positions.

Jan 3, 1961

By G. Herget

To improve quality control of roof conditions, a program was carried out at Elliot Lake uranium nines in Ontario, Canada to test a portable TV camera system. This camera has a 29 mm diameter probe and is capable of identifying crock locations, crack width and approximate dip direction. The extent of fractures to the roof was checked with the aid of a vacuum system by placing packers in various boreholes and checking for communication. The removal of some rock bolts indicated an increase in fracture extent.

Jan 1, 1982

ORE at the Jeffrey mine of Canadian John Mansville at Asbestos, Que., is hoisted by two 12 1/2 - ton capacity aluminum skips, counterbalanced. When the loaded skip reaches the surface it empties, via its sliding door, into a bin. Simultaneously, the skip tender, who operates at the 940 level, loads ore into the alternate skip from a 12 ½ -ton measuring pocket. This done, he sets the skips in motion. Problem: When moisture content of the asbestos ore is high, the ore, unknown to the skip tender, some- times sticks in the dumping skip, preventing complete discharge. Moreover, the sliding skip doors sometimes jam and stay open after the ore is discharged. If a skip in this condition is lowered, the result is either an overflow of ore, or the ore discharges through the open skip door, down the shaft. Spilled ore must then be mucked out of the spill pocket and hoisted in 2-ton cars. Cost is high, time is lost, and the shaft is sometimes damaged. Solution: A television apparatus was installed so that the skip tender might quickly spot improper door operation or hang-ups at the dumping station.

Jan 8, 1958

By C. G. McLaughlan

The Noranda concentrator was placed in operation in October, 1928, and the object of this paper is to outline operations during the twelve months which have elapsed since that time. The ores milled are massive sulphides carrying copper and gold, and, in certain cases, zinc. These ores have a specific gravity of about 3.8. The average assay of the copper-gold ore so far treated has been 2.0 - 3.5 percent Cu; 0.10 - 0.20 oz. Au; 40 - 51 percent Fe; and 6 - 15 percent SiO2. In this ore the copper occurs almost entirely as chalcopyrite, and the iron which is not combined with the copper is present mainly as pyrite and pyrrhotite. ?some iron is also combined with the silica, the ratio being about 1 to 4, and a small percentage is present as magnetite. The occurrence of the gold has been shown by microscopic work carried out by Prof. L. C. Graton, of Harvard University, to be very variable. Some of it is free, and is included within the base-metal sulphides or occurs at their boundaries. A similar distribution also holds for a portion of the gold which is combined as a telluride. Little is so far known of the occurrence of the silver other than that some of it may be combined with the gold in the telluride, petzite. The copper-zinc ore contains up to 6 percent copper, and has a very variable zinc content. The copper in such ore is present as chalcopyrite, and the zinc as sphalerite. In starting the mill we had three conditions to face; the first of these was climatic, the second was the lack of skilled flotation operators, and the third was the ore itself." The last of these three proved much more difficult to contend with than the other two combined.

Jan 1, 1930

By Rob Morrison, Peter Cameron

"Many products and technologies have been developed from outcomes of research projects carried out by the Julius Kruttschnitt Mineral Research Centre (JKMRC). When these products and technologies are applied to the design and optimisation of blasting, comminution and separation, improvements in profitability can be realised.In 1970 Alban Lynch promoted two practical ideas to improve plant operations:• Ore and equipment properties can be separated allowing experience with one type of ore or equipment to be transferred to other types of ore and equipment. If this experience was encapsulated in a mathematical model, then these properties could be combined and used to simulate (ie. to design and to optimise) complete mineral processing circuits.• Many problems associated with scale-up from laboratory to industrial equipment could be eliminated by experimental work on full-scale equipment in the plant.Many JKMRC research projects have focussed on the development of models of unit operations in mineral processing and their application to process simulation.Models of comminution and classification developed at the JKMRC have been used since the early 1980's. Ore characterisation techniques developed to support these models are licensed world wide through JKTech. The application of comminution modelling techniques to blasting, which optimises the process feed size distribution is used in Mine-to-Mill® projects. The advances in the understanding and modelling of froth flotation over recent years have provided the opportunity for integrated ore characterisation and process optimisation from resource to product.JKMRC project outcomes often provide proven opportunities for the mineral industry to improve performance and productivity. JKTech was established in 1986 to commercialise and market the most promising outcomes and thus ensure their continuing availability to the mineral industry.They include:• Commercial software (JKSimMet, JKSimBlast and JKMetAccount).• Monographs (Comminution and Blasting).• Technologies (Mine-to-Mill® and flotation optimisation).• Hardware products (JKFrothCam, JKJetLift® and the Mineral Liberation Analyser).This paper summarises these technologies and their benefits."

Jan 1, 2003

By Oliver M. W. Sprague

THIS gold problem is full of complications and can hardly be handled adequately or comprehensively in any short period of time. Perhaps I might begin by mentioning a few aspects of the subject about which I suppose there will be no disagreement. The first of these is that we already have a stock of monetary gold in the United States far in excess of what is needed to support any desirable increase in the present volume of currency and credit. The second is that this already superabundant gold stock is certain to be considerably enlarged during the course of the war, and presumably during the months of readjustment following its conclusion. Some billions of additional gold, we may reasonably presume, will come into the country during these next few years, thus increasing the aggregate monetary gold stock from the present eighteen billions to perhaps twenty- two or even twenty-five billion dollars.

Jan 1, 1940

By Sheldon P. Wimpfen, Ralph H. Sweefser

FOR centuries the pumping of water has been one of the chief problems to be overcome by the persistent men who win the mineral wealth of the world. Profitable operations have often been forced to suspend activities as the mine penetrated well below the water table or when sudden rushes of water were encountered. To operate below the local water level requires continuous pumping equal in volume to the amount of water flow¬ing into the mine workings. Often the water to be removed exceeds the tonnage of valuable material produced. To be above local water level is a valuable asset. Modern mining practice permits nothing short of the extraction of the last pound of profitable ore from a mineral deposit. In the days before the development of mechanical and electrical power as we know it today. water in any quantity was a major

Jan 1, 1948

By Maconochie A. P

The copper-gold orebodies of the Ok Tedi project and located in an area of climatic and topographic extremes, where both the landforms and the rocks from which they have developed are so young that it may be said that geological and engineering processes are coincident.

Jan 1, 1990

By Joël P. T. Kapusta

Back in 1995, Air Liquide and Union Minière presented a joint paper at the Copper 95 – Cobre 95 Conference in Santiago, Chile, describing the first full scale plant trials of shrouded sonic injection in a Hoboken converter at the Hoboken smelter in Belgium. Almost a quarter of a century later, the technology known as ALSI, or Air Liquide Shrouded Injection, has been tested or commercially implemented in several copper and nickel smelters. Despite these successes, the copper industry did not adopt it widely in the same manner the steel industry adopted the Savard-Lee tuyere in the 1970s and beyond, not even in the way the lead industry adopted it with the Queneau-Schuhmann-Lurgi, or QSL, process. The development and implementation of bottom-blowing smelting and converting technologies in China in the last ten years, however, changed the industry’s perception that high- and ultra-high oxygen injection in copper smelting and converting was indeed possible under specific process conditions. In this paper, I retrace the key learnings of my journey with sonic injection over the twenty five years from my humble beginnings in my early years with Air Liquide, through plant trials and technology implementation in the late 1990s and into the first decade of the new millennium, and ultimately, to the most conclusive proof that the sonic injection design methodology I established is valid, and the calculation tools I developed are accurate. I conclude by sharing my thoughts about whether the deployment of the Savard and Lee legacy within the nonferrous industry was just a pipe dream or whether it will become a reality. INTRODUCTION In the context of lower quality ores and changing economic markets, copper smelters need to continuously innovate and improve to remain competitive and respect their corporate social responsibility engagements. One avenue towards this business, social, and environmental goal is to increase process intensity while lowering fossil fuel consumption to lower greenhouse gas emissions and reducing process off-gas volumes to better capture As and SO2–laden emissions. I believe high oxygen sonic injection for submerged tuyere copper bath smelting and converting is one technology that can help smelters achieve that goal of higher business, social, and environmental performance. Twenty five years ago, when I discovered that the Savard-Lee tuyere had revolutionized the steel industry (Savard & Lee, 1966; Knuppel, Brotzmann, Fassbieder, Savard, & Lee, 1972), I had a dream — or was it a vision? — that within the first decade of the new millennium, modern copper smelters operating submerged tuyere bath smelting and converting vessels will have implemented high oxygen sonic injection and will be reaping the financial and environmental benefits that the steel industry enjoyed in the 1970s. As we approach the end of the second decade of the new millennium, I have to admit that my dream has been all but shattered as the majority of copper bath smelting and converting vessels today continue to operate under bubbling regime conditions. This mode of operation is archaic, still requires tuyere punching and blows at inherently low enrichment levels, particularly in converting, producing large volumes of process off-gases. Under such operating conditions, regulations and emission quotas for As, SO2, and particulate matter oblige smelters to use not just primary or secondary hoods, but sometimes even tertiary hoods. I vividly recall being told, fifteen or twenty years ago when visiting smelters to promote the application of the Savard-Lee tuyere in nonferrous processes, that implementing sonic injection was not economically viable due to the high cost of compressing air and oxygen. Some of the smelters I visited back then have since mandated their engineering partners to design and build secondary or even tertiary hoods. I cannot fathom how secondary and particularly tertiary hoods, with all of their auxiliary equipment and added ducting, could be more economically viable than purchasing and installing a few compressors, expanding the pipeline network for compressed air and oxygen, and installing a new control valve train to feed sonic tuyeres. Besides, adding hoods does not address the problem of As and SO2-laden fugitive emissions at its source but merely provides a costly mitigation for it by capturing larger volumes of process off-gases rather than reducing these large volumes in the first place. Moreover, hooding does not reduce energy consumption nor does it increase process intensity, two aspects that I believe are critical for smelters to remain competitive and sustainable in a deeply changing market environment.

Jan 1, 2019

By F. L. Bosqui

NO metallurgical process developed in the last half century has been more widely advertised to both technologists and lay- men, or has done more to promote efficiency and economy in the extraction of the valuable portions of ores than has the flotation process. Practically everybody has heard of this strange procedure whereby the heavy portions of an ore are made to float while the light parts sink. Some- times it is called froth flotation, the mineral-bearing froth being from the first a distinguishing characteristic. Many times it is called oil flotation, because a thin film of oil was commonly applied to the particles to be floated to make them adhere to the bubbles that rise through the pulp to form the surface froth. Oil, though commonly used, is not, however, necessary for this purpose, which is one of the facts that has been learned as the process has been developed.

Jan 1, 1940

By L. A. Cranson

WHEN I came out of Stanford University in 1922, the out-look for men trained in geology, petroleum engineering, and mining was indeed dismal; in fact, so much so that most of us looked upon our future in those fields as pretty hopeless. Neither our professors nor those men in industry with whom we came in contact gave us any enthusiastic encouragement as to the future of ourselves or the fields we had chosen for our labors. I believe that the attitude of pessimism which saturates everyone about graduation time is lament able and short-sighted, and may often start a young man on his way with an attitude of defeatism. Instead, he should be starting out knowing that he can expect hard work and keen competition, but that the fields of his labours are expanding at an accelerated rate, and that strong, energetic efforts will as always accomplish highly satisfactory results.

Jan 1, 1941

By J. Q. McNatt

Mr. President and Members of the Rocky Mountain Coal Mining Institute: It is a great pleasure to be with you at this meeting, to enjoy the entertainments, and the good fellowship of all present., as well as to become better acquainted with the men in general. In presenting my subject today, .1 feel like the darky, who was home-, ward bound, had become weary and sat down by the wayside to rest. Presently glancing about to view the scenery, he spied a. large brown bear slowly coming down the path scenting his tracks one by 'one as he advanced. The darky to be polite said, "Mr. Bear, I see you like my tracks, I will make you some more." I have on. a few occasions given some interesting information on the various subjects such as The Prolonged Famines of Arabia, Movements and Migrations of the Races of Men, Life Indications on the Planet Mars, and today I have come before you with a new step in the roadway-Coal Geology. It is sometimes difficult to interpret the geological processes so as to be understood intelligently, but it shall be my aim to make this as plain as possible.

Jan 1, 1927

By Allen Rogers

TWENTY-FIVE DOLLARS for nothing at all except a sheepskin. That to me is the effect of the New York State law for registration of engineers and the same may be said of any of the state licensing laws. Of course, if one has to practice in more than one state, he must pay a more or less equal amount for every state he works in; and yet there has been little effective protest against these laws. It would seem that the spirit which animated the Boston Tea Party is non-existent amongst engineers. Undoubtedly a good many consider, through their failure to understand the law, that the matter does not affect them. In New York State it is provided that "any person practicing or offering to practice profes-sional engineering or land surveying . . . shall be licensed as hereinafter provided." To quote further from the law: "A person practices professional engi-neering . . . who holds himself out as able to do, or who does, the work that an engineer does . . . " The cunning of the wording of this article can only be appreciated by considering that anyone calling himself an engineer falls within the definition; its liberal inter-pretation (I have not quoted the whole of it) would embrace many who do not consider themselves engi-neers. The state authorities may not construe it to include such individuals; indeed, they may possibly consider it inexpedient to extend it to include engineers of subordinate grade, but the possibility is always there and, even though an engineer be of the grade of assis-tant, he may at any time be called upon to substitute for his principal in responsible charge of the work. It is therefore clear that anyone calling himself engineer and practicing engineering must, for his own protection, apply for registration or run the risk of violating the law. Now, what is the sense of all this? We have done very well without such restrictions on the means of gaining our livelihood. If one only stops to think, there is hardly a minute of his modern existence when he is not dependent for his safety on the engineering by engineers of yesterday or today. How often is one in jeopardy through failure of engineering works, work done under the supervision of those same engineers? If all of us had to wait for our ends by such means, our average life would probably be some thousands of years. Where, then, is the point to the object declared in all these laws that the need for licensing is "to safeguard life, health and property?" Bosh!

Jan 4, 1923

The sixth international symposium on mining with fill nearly coincides with the 25th anniversary of the Jubilee Symposium on Mine Filling. That symposium, held in August 1973 in Mount Isa, in part to commemorate the 80th anniversary of The Australasian Institute of Mining and Metallurgy, was the first in what has turned out to be a very successful series of symposia. Subsequent symposia were held in Sudbury, Canada (1978), Lulea, Sweden (1983), Montreal, Canada (1989) and Johannesburg, South Africa (1993). The series of symposia has now become an established part of the mining industry calendar, and it will be interesting to see which country is given the honour, and accepts the challenge, to organise the next symposium.One way of predicting the future, or some small part of it, is to revisit where we have already been with a view to determining the existence of any trends that may impact on the future. An historical review of filling practice and research, with special emphasis on Australian experience in particular and worldwide in general over the previous 25 years, will enable me to address the historical and predictive objectives. Controversy can always be achieved by producing a best of list; it can be guaranteed that everyone will disagree with at least one of the nominations. On this occasion, the best contributions by individuals or groups in a number of areas of mine fill technology, over the last 25 years, will be the basis for the nominal awards. The controversy can be increased by posing a number of questions that, hopefully, some of the authors will address during their presentations. I imagine the social functions will be busy enough, but the questions may just add to the cut and thrust of the debate.

Jan 1, 1998

The sixth international symposium on mining with fill nearly coincides with the 25th anniversary of the Jubilee Symposium on Mine Filling. That symposium, held in August 1973 in Mount Isa, in part to commemorate the 80th anniversary of The Australasian Institute of Mining and Metallurgy, was the first in what has turned out to be a very successful series of symposia. Subsequent symposia were held in Sudbury, Canada (1978), Lulea, Sweden (1983), Montreal, Canada (1989) and Johannesburg, South Africa (1993). The series of symposia has now become an established part of the mining industry calendar, and it will be interesting to see which country is given the honour, and accepts the challenge, to organise the next symposium. When the chairman of the conference organising committee invited (or was it instructed?) me to prepare and deliver one of the keynote addresses, his request was for me to be in parts historical, controversial, predictive and entertaining. The mix was left to me, with one proviso - that an early pioneer of mine filling in Australia be given due recognition. The chairman of the organising committee alone will be able to determine if I fulfilled the last objective. My success, or otherwise, with the other objectives will have to be judged by my fellow delegates. One way of predicting the future, or some small part of it, is to revisit where we have already been with a view to determining the existence of any trends that may impact on the future. An historical review of filling practice and research, with special emphasis on Australian experience in particular and worldwide in general over the previous 25 years, will enable me to address the historical and predictive objectives.

Jan 1, 1998

UP TO and including 1931, the twelve mines that were treated in THE PORPHYRY COPPERS had produced 17.4 billion pounds of copper worth $2,820,000,000. With a little help from six others (three of them did not start output until 1954) that record had been increased at the end of 1955 to 60.5 billion pounds worth $10,440,000,000. Today, ten billion dollars is not as impressive as it once was; but it still represents a lot of value. It must be remembered that this is newly-created wealth, produced entirely from material considered worthless when the Porphyry era started about fifty years ago. At that time "rock" that contained less than forty pounds of copper per ton was regarded by competent mining engineers as value- less. It was not "ore" in the economic sense. Today, ore is being successfully exploited that contains less than twelve pounds of copper per ton. Also, in Peru, a typical Porphyry operation is being launched by a partnership of four United States mining companies that will involve an initial capital investment of $200,000,000 for mine development, plant construction, and the provision of related facilities. Of this project more will be said at the end of the chapter. The point I want to make now is twofold: (1) that phenomenal progress has been made in Porphyry engineering and technology; and (2) that exploitation of an important Porphyry copper deposit has become an industrial enterprise of truly great magnitude. Much had been accomplished by 1931; but that progress has been dwarfed by the achievements of the past 25 years- a fact that, in the nature of things, is as it should be.

Jan 1, 1957

By Charles Fairhust

Although the term 'rock mechanics' started to become popular about the time of the First U.S. Rook Mechanics Symposium in 1956, study of the mechanical behavior of rock certainly pre-dates this event. Bucky, Phillips, Von Karman, Fayol, Galileo...the list of significant contributors can be traced back over centuries, - not surprising for the oldest structural material used by man. Started with a strong mining orientation by the Colorado School of Mines, University of Minnesota, and Pennsylvania State University, joined soon after by Missouri School of Mines and the University of Texas, the Annual U.S. Symposium on Bock Mechanics has evolved into the main U.S. form for discussion of all aspects of rock mechanics, basic and applied - tectonophysics to comminution; near-surf ace foundations to deep mine support design. Although dominantly a U.S. event the annual symposium has benefitted from regular and important contributions from abroad. It would be presumptuous to attempt a comprehensive statement of significant developments over the 25-year history of the U.S. Bock Mechanics Symposium. This anniversary address will attempt instead to present a personal view of developments that appear to be of broad general significance and that may indicate directions for the future. Among the developments to be discussed in the address arc the following: - Energy Basis of Book Fracture Early rock mechanics investigators often overlooked the important distinction between a failure initiation stress and structural collapse. Although essentially synonymous in the

Jan 1, 1984

By Stephen C. Tadolini

The International Ground Control Conference in Mining has always provided an open forum for the publication, presentation, discussion, and often heated debate on roof bolting systems mostly with attention to how, when, and why they work. During the last 24 Conferences at least 170 papers have been presented by International Experts on these ?simple? devices that range in length from 30-inches to 20 ft and from 5/8 to 2 inches in diameter. Roof bolts are primarily mechanically anchored, glued, cemented, or driven. Bolts are placed vertically, angled, or tied together with special fixtures (trusses and slings). They have been termed active, passive, stick-slip, and several other descriptive acronyms or mining slang expressions. This retrospective paper will present the changes in bolt types and usage, point out some of the biggest myths and hail the most significant advances (according to the authors? opinions of course).

Jan 1, 2006