Search Documents

The use of belt air in underground coal mines has been a continuous discussion since it was first introduced in the Federal Coal Mine Health and Safety Act (Coal Act) of 1969. Although the Coal Act prohibits the use of belt air to ventilate active workings, there were two exceptions prior to the 2004 Final Rule. There have been several major studies/rule-proposals by MSHA since 1985 and the most recent of which is the Technical Study Panel (TSP) established by the Mine Improvement and New Emergency Response (MINER) Act of 2006 to study the use of belt air and related issues. This paper reviews the history of belt air use, its associated controver-sies, and more specifically, the 20 recommendations unanimously approved by the TSP.

Jan 1, 2009

Both blast furnace and steel furnace slags have been used extensively and successfully on main line railroads in the United States for more than 25 years. Annually, these slags are being used as ballast at the rate of about 4 million tonnes of blast furnace slag and 1 mil- lion tonnes of steel furnace slag, much of it on main line with 90 metric tonne car loadings. More steel furnace slag would be used if it was available. Both slags meet all the specification limits of the American Railway Engineering Association. Actual use on high density rail- roads has confirmed the long range economics of their use. Comparison of laboratory tests, such as Los Angeles abrasion, with actual field per- formance has shown conclusively that commonly used laboratory tests can not be used to accu- rately compare the quality of various types of ballast materials.

Jan 1, 1979

By Paul Weir

BLEACHING clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller's earths fall within the general group of bleaching clays and gradually the commercial term "fuller's earth" has been applied to natural clays originating, for the most part, in the south-eastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States.1 Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). TABLE 1.-Physical and Chemical Composition of Different Types of Clays Composition, Per Cent Constituents and Properties Bentonite Fuller's Mud Clay (Wyoming) Earth (P Peak)' (Alluvial) Silica (SiO2) 60.0 69.6 61.67 Alumina (Al203) 19.0 14.3 20.34 Ferric oxide (Fe203) 2.8 3.90 7.70 Titanium oxide (Ti02) 0.13 0.70 1.01 Lime (CaO) 0.5 0.80 0.00 Magnesia (MgO) 2.0 1.00 0.24 Soda (Na2O) 2.4 0.40 0.31 Ignition loss 4.7 6.77 8.51 Moisture content 8.0 10.0 20.0 Isoelectric point, pH 9.2 9.2 6.5 Average swelling volume 15.0 0.0 0.0 Weight per cubic foot, lb 55.0 40.0 65.0 Material passing 200-mesh sieve, per cent 90.0 85.0 50.0

Jan 1, 1939

By Paul Weir

BLEACHING clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller's earths fall within the general group of bleaching clays and gradually the commercial term "fuller's earth" has been applied to natural clays originating, for the most part, in the south- eastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States. Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). [ ] The fuller's earth type of clay is characterized by a lack of plasticity, relatively adsorbent, foliated structure, and does not swell to form a

Jan 1, 1939

By Bekir Karasu

Boron raw materials are amongst the most important natural sources for many industrial branches and their values become increasingly raised with the discovery of boron usage in many new technological fields. All the countries in the world are unfortunately not as lucky as Turkiye and USA where major boron deposits are mainly located. It is widely known fact that on one side, boron is very precious component with its technological importance, on the other; only its limited sources are available. Therefore, even its wastes have to be evaluated and regained. In the present work wastes of Etibor Kirka Borax Company of Turkiye were used in the production of opaque frits which was suitable for floor tile glazes. Standard and newly produced frit based glazes were applied on the pre-engobed floor tile bodies and single firing was employed. Final products were examined according to the certain standard tests and their microstructures were also investigated. All the results confirmed the evaluation of boron wastes in opaque floor tile glazes.

Jan 1, 2006

By Lilian Silva Costa, Laila Bonzi Ramos, Marcela Lessa de Freitas, Igor Quaresma Vianna

The eighth pelletizing plant, located at the Tubarão complex Industrial Unit of Vale S/A in Vitória-Espirito Santo-ES, processes a pellet feed primarily composed of compact and friable itabirite from Itabira and Brucutu concentration plants, located in the iron quadrangle in Minas Gerais-MG. The use of hydrated ores in the composition of the fine piles, such as Brucutu's common fines amphibolite itabirite (FABR), and Fábrica Nova pellet feed (PEFN), contributed to increase the energy efficiency of comminution, increasing the production of tumbling ball mills, minimizing the impacts during a mill preventive maintenance.

Oct 1, 2019

By N. Rajmohan, K. T. Jacob

Presented is a thermodynamic feasibility analysis of extracting base metal chlorides from low-grade, multi-metallic oxide ores using CaC[1]2 as a chlorinating agent in the presence of SO2 and O2. The oxides react to form corresponding chlorides, while CaC[1]2 is converted to CaSO4. The Ellingham diagram is used for comparing the standard Gibbs' free energy change for the sulfation-chlorination reaction of a large number of oxides. Except for alumina, silica and chromia, most of the other metal oxides will be converted to their respective chlorides. The volatile chlorides can be condensed, and the chlorides present in the condensed state can be leached. A process is proposed that uses a nontoxic chlorinating agent and gives an efficient separation of the metallic values from the gangue.

Jan 1, 1993

By III Westbrook

Although calcium sulfate dihydrate, commonly referred to as gypsum, has been utilized for some time in fiberglass reinforced polyester (FRP) applications, it does not have the fire retardant filler recognition of ATH. Gypsum is more commonly known for application in cement, soil and water treatment, plaster, and wall-board. Inherent characteristics of gypsum limit its use to low temperature and, until recently, non-aqueous applications. However, as a plentiful, naturally occurring hydrated mineral, the cost effectiveness of calcium sulfate dihydrate has prompted development and yielded success in the areas of FRP spray-up and latex carpet backing.

Jan 1, 1993

By Rashchenko AF, Voiloshnikov GI, Elshin VV, Khomutov VV

The sorption method for the precious metals recovery fromsolutions and pulps are a perspective trend of modernhydrometallurgy. Russian gold mining industry uses thesemethods, anion-exchange resins being applied as sorbents. Theanion exchange resins allow effective recovery of preciousmetals, however, they have several drawbacks as compared withactivated carbons: high cost of sorbents; difficulties arisingduring treatment of pulps with complex ion composition;necessity of using titanic equipment and thiourea for gold elutionfrom loaded anion-exchange resin and its regeneration.

Jan 1, 1993

By Denisio Miranda Custódio, Rodrigo Boyer, Josiane Lira Batista Haagensen, Raquel Teixeira Pereira, Felipe Viana Pimenta, Rossano Augusto Pilon Nunes

In the Tubarão Pelletizing Plants, anthracite is used as solid fuel, which has fixed carbon content of 72%. This paper will present the pilot scale results and industrial scale tests of an alternative fuel to anthracite, named Blast Furnace Dust. All the work was developed using samples from Arcelor Mittal Tubarão, due to it has a large source of production and is near to Vale/SA, which reduces significantly the cost for the material’s transportation. There was an impact on the variability in fixed carbon results of the slurry, mainly at the beginning of the test, reaching very high levels and put on risk the pellets physical’s quality. This variation can be explained by some operational disturbances and, mainly, by the low predictability of Blast Furnace Dust quality and lack of an adequate system for material preparation and dosage.

Oct 1, 2019

By P. Kitobo, T. Nduba, D. Mbay, J. B. Vangu, R. Ciband

The flotation plant tailings at Kamoa Copper Mine concentrator were found to contain a high proportion of extremely fine particles. The potential issues with settling these fine solids were resolved by the use of a poly-di-allyl-di-methyl ammonium chloride (DADMAC) coagulant, Flobead DB 45 VHM, in conjunction with a standard anionic polyacrylamide flocculant. This paper outlines some of the issues encountered and how they were resolved at the Kamoa concentrator. The potential to use this process and technology at other sites is also considered

Jan 1, 2023

By Maneesh Singh

During the various stages of iron & steel production a number of iron-rich by-products are generated. The traditional way to recycle them back to the blast furnace has been the balling - sintering process. These by-products can also be made into cement-bonded agglomerates for use as burden material for blast furnaces. In order to improve the quality of agglomerates the effects of various processing parameters on the properties of cement-bonded briquettes have to be controlled. This paper looks into the various aspects of producing cement-bonded agglomerates and using them as burden material for blast furnaces.

Jan 1, 2003

By G. N. Nnadi, R. J. Mitchell

"The response of cemented backfills subjected to simulated blast loadings is studied using centrifugal modelling techniques. Scaling requirements for centrifugal modelling are developed and the results of the similitude analysis show that an acceleration field is required to capture the true dynamic response of backfill models. Experiments have been conducted at various centrifugal accelerations. The effects of ring blasting were simulated by an impact loading on the exposed fill face. The behaviour of the cemented backfill was monitored with accelerometers as well as dynamic stress gauges.Cemented backfill response to impact loadings was found to depend strongly on simulated gravitational stress level. Results also show that the characteristics of the response changes with distance from the impact. Finally, the results of the models were used to predict prototype peak accelerations, velocities and displacements. The results reported in this study indicate that centrifuge modelling may be a useful tool for dynamic studies of blast damage to backfills. Centrifuge modelling can be carried out at low costs and can be used to design prototype instrumentation systems. IntroductionThe response of cemented mine backfills to blast loadings is of concern to the mining industry because these backfills provide local and regional support during ore pillar extraction. Considerable research has been reported on the static stability (Smith et al., 1983) and on effects of reinforcements on cemented backfills (Mitchell, 1989). However, information regarding dynamic aspects of cemented backfill is limited. O'Hearn and Swan (1989) reported on the response of cemented backfill to blast loading, but these blasts were not very dose to the backfill . A schematic representation of a rock-backfill system is shown in Figure I.The mechanics of transfer of explosive energy to rock and subsequently to the backfill, and the resulting responses, are complex. Achison (1968) listed more than twenty factor s affecting the blast fragmentation of rock and grouped these into the categories of explosive parameters, charge parameters and rock parameters. Although significant advances have been made, during the past two decades, in understanding the mechanics of blasting, the degree of uncertainty associated with predicting the behaviour of backfills subjected to dynamic loadings makes the application of simple design safety factors insufficient. Comprehensive testing programs or prototype instrumentation is required to evaluate the risks associated with blast or earthquake loadings on backfill."

Jan 1, 1991

By Anthony C. Mulligan

Metals have historically been used in mining since they offer an excellent combination of hardness, toughness and cost and can be fabricated to form a variety of shapes. However, for many applications the metals used today have limited performance in the environments in which they are needed. This is particularly true for geothermal environments where the brines are highly siliceous causing corrosion and accelerated wear of many components. Geothermal sources are increasingly being explored for their high thermal value as well as possible sources for future minerals. While advanced ceramics have historically been expensive to produce in comparison with metals, they offer significantly greater corrosion resistance and hardness and can improve the overall performance when used in selected ?problem? areas. One of the major drawbacks in the use of ceramics in high impact areas has been their brittle nature and propensity to fracture and spall (fail) when loaded. Recent advances in the fabrication of ceramics have combined hard (strong) ceramics with more ductile ceramics in a architecturally designed microstructure, thus allowing ceramics to perform well in these high impact regions. Additionally, ceramics are significantly more inert to corrosion from either alkaline or acidic environments and can typically be used for significantly longer periods in these environments than their metallic counterparts.

Jan 1, 2006

By Michael A. Trevits

Since the promulgation of the MINER Act and the follow-up changes to the regulations governing mine seal construction and maintenance, mine operators must be acutely aware of the atmosphere in sealed mine areas and prepared to deploy control technologies when the conditions are warranted. On Site Gas Systems1 in Newington, Connecticut was awarded a contract by the National Institute for Occupational Safety and Health (NIOSH) to construct a novel in-mine nitrogen (N2) generation plant using pressure swing adsorption (PSA) technology. PSA technology utilizes carbon molecular sieve material and pressure to adsorb oxygen (O2) molecules while allowing N2 molecules to pass through the sieve material. The prototype PSA unit was tested at the NIOSH Safety Research Coal Mine (SRCM) where a 62,000 ft3 area of the mine was rendered inert during a series of two tests. The resultant data were then used to construct a CFD simulation of both injection tests. In addition, O2 depletion and gas leakage rates were quantified in the model and were compared to actual values. Once the model was calibrated, the sealed mine area was doubled and simulations were made with various injection rates and injection site locations to determine the impact on the time needed to render this area inert. This paper presents an overview of the PSA plant, the details of the gas injection tests and CFD modeling work.

Jan 1, 2010

By M. Tangstad, B. Monsen, H. Midtgaard

The increased attention towards reducing emissions of fossil CO2 due to its potential global warming effect has resulted in a focus on renewable resources, as charcoal. Since charcoal is produced from growing wood it does not contribute to global warming. This paper gives a brief review of consequences of and reasons for using charcoal in the silicomanganese (SiMn) production. Results are presented from practical SiMn smelting experiments, on a pilot scale, using charcoal as reduction material and comparing with coke. As slag- and CO2-reactivity are important for furnace performance these features have also been measured.

Jan 1, 2004

By P. K. Ackerman, F. F. Aplan, G. H. Harris, R. R. Klimpel

Fourteen reagents that are potentially capable of chelating with a metal ion on the surface of the major copper sulfide minerals and pyrite were evaluated for their effectiveness in floating these sulfides. The reagents studied fall into the classes of mercaptobenzole mutations, thiouronium, thionocarbamates, thiourea, imidazole mutations, oximes, hydroxyquinoline and xanthogen formate. The best overall copper sulfide collector was an imidazoline (1-Hydoxyethyl - 2-Heptadecenyl), but it also proved to be an excellent collector for pyrite. Its potency as a pyrite collector can be reduced by structural alteration, but at some loss in its collecting power for the copper sulfides. The effectiveness of many of these potential collectors can be changed by minor alterations to the collector molecule and, to a lesser extent, by pH adjustment. The general order of mineral floatability with these reagents is chalcopyrite = chalcocite > covellite =bornite >> pyrite. The flotation of malachite is generally similar to that of the copper sulfides, indicating the special effectiveness of copper in the crystal lattice for collector attachment.

Jan 1, 2000

By Matias Pentinnen, Wayne Dickinson

Electrowinning is a key process for copper production contributing roughly twenty percent globally and thirty to forty percent of production in the Americas1. Copper grade is assessed largely on deposit smoothness and on level of impurities in the metal. Smoothing aids are essential to create dense, low porosity deposits and guar has long been the material of choice for this purpose. Guar is, however, poorly stable under the strongly acidic electrowinning conditions, underlying ongoing research to identify an effective, acid-tolerant replacement. Current efficiency is also a critical factor in controlling copper production costs and chemical additives should ideally improve current efficiency as well as improving deposit smoothness.

Feb 1, 2025

By Chandrakala Kari, S. Mohan Rao, Gajanan Kapure, K. S. Raju

High carbon ferrochrome production process is energy intensive, consumes approximately 3300-3400 kWh per ton of metal produced. This amounts to ~ 34% of the total ferrochrome production cost. The power costs in India are almost 4 times greater than the leading ferrochrome producing countries like South Africa. Hence there is a need to look for alternative sources of energy. In ferrochrome making process large volumes of high concentration CO gas (~ 85%V) is developed at ~400-5000C, which if combusted within furnace represents high potential for significant electrical energy savings. In a typical heat in the state-of-the-art submerged arc furnace, about 34 kmol of CO gas is generated per ton of ferrochrome metal, which, if post combusted to CO2, represents 7620 MJ of energy. Post combustion of the evolving CO (and H2) gas to CO2 can be achieved by providing additional oxygen before the generated CO gas leaves the furnace. In this paper, a concept of post combustion in submerged arc furnace as potential source of significant electrical energy saving in ferro-chrome making process has been explored. The prospects and limitations of the same are discussed. The value of this paper lies in its attempt to explore the post combustion application to submerged arc furnace with an objective of significant reduction in electrical energy consumption in ferrochrome production process.

Jan 1, 2007

By N. S. Dalal, V. Castranova, K. Van Dyke, V. Vallyathan

"IntroductionInhalation of crystalline silica is often associated with the development of pulmonary disease (Ziskind et al., 1976). Recently, it has been proposed that freshly sheared silica .may have surface properties that make it more reactive with lung tissue than aged silica, and that this unique reactivity ·of freshly crushed silica enhances its pathogenicity. A recent study in our laboratory strongly supports this theory (Vallyathan, et al., 1988a; 1988b). We found that grinding of silica cleaves bonds in a silica tetrahedral lattice generating reactive free radicals sites on the surface of the silica particles. The presence of surface radicals on freshly ground silica was monitored by electron spin resonance (ESR) spectroscopy. The ESR signal generated from fresh silica in air is characteristic of Si-0 and Si radicals. Evidence, i.e., the ESR signal after the addition of a spin trap (DMPO) and its sensitivity to ethanol, indicates that these silicon-based surface radicals can react with water to form hydroxyl radicals (OH). Results also indicate that these surface radicals make fresh silica more cytotoxic than aged silica; i.e., fresh silica causes more membrane damage as evidenced by hemolysis and lipid peroxidation. Therefore, the presence of reactive sites on the surface of freshly cleaved silica may play a significant role in its pathogenicity.If surface· free radicals are related to cytotoxicity, then screening dusts for the existence of such radicals may predict their relative pathogenicity. Since an ESR spectrometer is not available to many laboratories, the objective of this study was to develop a quick and simple technique to monitor the existence of reactive surface sites on dust. The technique chosen was the measurement of chemiluminescence using a liquid scintillation counter; i.e., an instrument which·would be accessible to most investigators."

Jan 1, 1989