Search Documents

By M. D. Mwema

Copper oxide ores deposits in the Katanga province of the Democratic Republic of Congo (DRC) contain at variable level cobalt oxide minerals. In contrast to copper oxide minerals which readily dissolve in the sulphuric acid solution, the cobalt oxide bearings are difficult to dissolve, especially if cobalt is present in the third oxidation state (Co2O3). This species become soluble after reduction of Co+3in Co+2. In practice, the use of reducing agent is therefore necessary in order to transform the insoluble minerals into soluble cobalt sulphate species. The following reducing agents are currently used at the Shituru plant: ferrous ions, which are present in leach solutions, pulverised copper or sodium meta bisulphite (MBS). Due to the high consumption of reducing agents (0,8 t MBS/t of solubilized Co; 1,2 t Cu/t-Co), cobalt production is expensive. The use of sulphur dioxide as reducing agent was then investigated in order to reduce operating cost. This reagent also presents the advantage of sulphuric acid production during the leaching process. It has been added in the leaching vessel (tank). From the laboratory and industrial tests, selective leaching of cobalt (78%) has been performed. The cobalt leaching kinetic depend on sulphur dioxide dosage. Dissolution of copper, iron and manganese remained very low. No emanation of SO2 gas was observed during the process.

Jan 1, 2002

By S. Corrent, F. A. V. Guimarães, M. G. Barbosa

"INTRODUCTION Moisture can be a villain, so new technologies have been explored to make more viable the production of high moisture iron ores. The current work presents the attempt of the utilization of a superabsorbent polymer (SAP) to aid in the screening process and in the ore handling process, such as stockpiles reclaiming and vessels/trains discharge in sub-zero temperature conditions. The results have shown that the polymer can be used in certain cases to improve productivity and increase safety in the process of handling the material (by increasing the TML). However, for size separation no advantages were found upon the use of the polymers. WATER ADSORPTION MECHANISMS The use of water in mineral processing is constant as its utilization brings an increase in the efficiency of separation. Although we have better results in the processing with water, materials with a high content of “natural” moisture can be very difficult to be treated by the conventional methods of separation. Nowadays many studies have been conducted in order to understand the effect of adsorption of water in the particles of complex minerals. Those studies have being divided in many different lines of research such as contact angle of a drop of water and the surface of the mineral to determine hydrophobicity, the particle size distribution and the porosity of particles. Mainly two forms of adsorption of water by the particles are possible: one the water is retained inside porosity of the particles. Laboratory tests developed in China have showed that capillary adsorption is faster in coarser particles that achieve the saturation degree earlier than finer particles (Xuewei Lv et al., 2011). The so called non-porous model considers the effect of water in the bulk sample of iron ores, in a physical connection when all the water works as a binder between particles as shown in the figure 1.If we take into account the compressibility of the system and compaction due to the weight of the bed over the particles, the thickness of the water film between particles is the same but the volume inside different particle size systems is much higher than in a system with particles of same size."

Jan 1, 2018

By J. W. Wilson, Y. P. Wang, M. H. Erten

The use of water is still the most effective and economical means for dust control in underground coal mines today along with dilution by the ventilation current. Studies have shown that the dust capturing capacity of water is a result of a balance of many intermolecular forces. Surfactants are known to reduce such forces by affecting both the surface tension of the liquid and its interfacial tension against a solid. Surfactants can be added to the water sprays to facilitate the dust capturing capacity. A laboratory scale model has been developed in which surfactants were added to the spraying water and preliminary data indicates positive results.

Jan 1, 1991

By Rebecca S. Stanevich

BACKGROUND Diesel exhaust is an animal carcinogen, although evidence of the carcinogenicity in humans is "limited". (World Health Org. , 1989) Of the eight cohort studies in the 19808, five found an increased risk for lung cancer among workers who may have been exposed to diesel exhaust (RR from 1.3-1.5, SMR from 101-132). (Howe, et al., 1983) Only two studies accounted for smoking indirectly. Of the ten case-control studies in the 1980's, eight reported increased risk of lung cancer among those populations purportedly exposed to diesel exhaust. (Benhamou, et al. , 1988) All but one of these adjusted for smoking and other occupational exposures. The odds ratios ranged from 1.2 to 2.1. In two of these studies, miners experienced a two to three fold risk. (Benhamou, et al., 1988) Bladder cancer has also been linked to diesel exhaust in cohort and case-control studies. Excesses of approximately 50% were observed among truck drivers in studies by NCI. (Hoar, et al., 1985) In the National Bladder Cancer Study, risks for truck drivers rose with duration of employment. A study by NIOSH in Ohio also found an excess of bladder cancer among truck drivers, particularly among those with 20 or more years of employment. (Steenland, et al, 1987) Despite the large number of studies in which the relation between diesel exhaust exposure and lung cancer has been examined, exposure to diesel exhaust has been quantitatively estimated only in the studies of railroad workers and truck drivers. (Woskie, et al., 1988) The excess lung cancer risk experienced by workers in these two occupational groups was modest, ranging from 40 to 90% for those with long-term employment. However, diesel exhaust exposure among railroad workers and truck drivers is lower than that seen among miners. Several markers of diesel exhaust have been utilized in these studies. Diesel exhaust is a complex mixture of particulates, vapors and gases. One group of these gases, the nitrogen oxides, react with polynuclear aromatic hydrocarbons, forming mutagenic and possible carcinogenic nitrated derivatives. (World Health Organization, 1989) For this reason, and because it is easy to measure and analyze, NO, was frequently used as a marker of diesel exhaust exposure. As part of the Garshick (Garshick, et al., 1988) study of railroad workers, Woskie measured NO, exposures of 477 railroad workers. (Woskie, et al., 1988) Geometric mean exposures of 13 job groups ranged from 12 to 80 ppb. In a New Mexico potash mine, (Attfield, et al. , 1982) exposures of from 100 to 3300 ppb nitrogen dioxide

Jan 1, 1992

By L. A. Rose

AMONG the half-dozen major research search projects now being conducted at the Michigan College of Minim, and Technology under the terms of an FERA grant, an important one relates to the use of suspensions in ore dressing. The study has resulted from the constantly widening industrial use of metals and minerals. The modest demands of a few decades ago for these minerals could be easily met from richer deposits. Now, at least in some localities, the richer deposits are nearing exhaustion. Furthermore, advances in the industrial arts and the competition of other minerals and metals have changed the specifications of materials needed by the manufacturers. Premiums and penalties enter into the sale value. Hence, to meet the requirements for amount and quality, washing and other ore-dress-

Jan 1, 1935

By A. Boulton

Low molecular weight synthetic polymers substituted with hydroxyl, carboxyl or sulfonate functional groups were used to improve the flotation separation of zinc or copper sulfide minerals from iron sulfide gangue minerals in three massive sulfide ores of different mineral composition. These polymers produced significant improvements in zinc or copper grades as a result of a selective depression of iron sulfide minerals. It was shown that this selectivity was the result of preferential adsorption of the polymer on the surface of the iron sulfide minerals. The different types of interaction between the functional group on the polymers and the sulfide mineral surfaces could explain the trends observed in the flotation results.

Jan 1, 2003

By A. Boulton

Low molecular weight synthetic polymers substituted with hydroxyl, carboxyl or sulfonate functional groups were used to improve the flotation separation of zinc or copper sulfide minerals from iron sulfide gangue minerals in three massive sulfide ores of different mineral composition. These polymers produced significant improvements in zinc or copper grades as a result of a selective depression of iron sulfide minerals. These results are significant considering the differences in ore type, proportion and type of iron sulfide minerals present, and grinding medium used in this study.

Jan 1, 2003

By W. R. Reed

The National Institute for Occupational Safety and Health (NIOSH) uses light-scattering dust monitors (nephelometers) in its research to develop dust controls to reduce respirable silica dust overexposures in miners. Recently, the model 1500-pDR, an active nephelometer, was introduced by Thermo Scientific. Testing was completed to ensure compatibility with the metal/nonmetal mine dust personal sampling unit (M/NMDPSU). Results of testing demonstrated that gravimetric concentrations measured from the 1500-pDR are comparable to the gravimetric concentrations measured using the M/NMDPSU, without need for correction, under commonly observed dust loading conditions.

Jan 1, 2012

By W. R. Reed, W. J. Archer, A. B. Cecala, J. D. Potts

The U.S. National Institute for Occupational Safety and Health (NIOSH) uses light-scattering real-time dust monitors (nephelometers) in its research to develop dust controls to reduce respirable silica dust overexposures in miners. Recently, the model 1500-pDR, an active nephelometer (i.e., with cyclone and pump configuration), was introduced by Thermo Scientific. Testing was completed to ensure compatibility with the metal/nonmetal mine dust personal sampling unit (M/NMDPSU). Results of testing demonstrated that gravimetric concentrations measured from the 1500-pDR are comparable to the gravimetric concentrations measured using the M/NMDPSU, without need for correction, under commonly observed dust loading conditions.

Jan 1, 2012

By G. Danha, S. Wabula, D. Glasser, D. Hildebrandt, N. Hlabangana

"Impact tests on single particles or a bed of particles are used to determine the fracture characteristics of particles. Many different techniques have been adopted in comminution in order to find ways of optimizing energy consumption in the size reduction process. In this paper, we apply one such method called the Attainable Region (AR) analysis technique to optimize the impact energy on a bed of silica particles. The attainable region is a fundamental approach that is equipment-independent and can be used to analyze breakage processes. The AR is defined as a set of all possible outcomes, for the system under consideration that can be achieved using fundamental processes operating within the system.INTRODUCTIONThe energy crisis in Southern African has reached such critical levels, that most cities in countries like Zambia, Zimbabwe, Lesotho, Swaziland and even South Africa are experiencing load shedding challenges lasting sometimes up to 18 hrs a day. Southern Africa is well known for its riches in mineral resources, and the economies of most states in this region are driven by the mining & mineral processing sector. With the emergence of small scale miners due to government empowerment policies, national energy providers have had to resort to power cuts mainly to domestic users in a bid to cope up with the huge industrial electricity demands.It has been estimated that about 4% of the total energy used in the world is consumed by the mineral processing sector (Fuerstenau & Lutch, 1999). Tomanec and Milovanovic (1994) estimated that milling alone accounts for more than 50% of the total power used in mineral processing, but this can rise to as high as 70% for hard or finely dispersed and inter-grown ores. Today, the greatest challenge in mineral processing is how to optimize energy input to the size reduction process (Dey & Das, 2013; Nomura & Tanaka, 2011), where it has been observed that only a small percentage (1.5%) of the total energy input really does the breaking (Khumalo et al., 2008) while the rest is consumed by the equipment concerned and lost to contacts that do not result in breakage. The immediate benefits of focusing research on the optimization of energy in size reduction operations in the mineral processing sector lies in potential savings on industrial electricity usage that may then be directed towards domestic users."

Jan 1, 2016

By G. Danha, D. Glasser, D. Hildebrandt, N. Hlabangana

"In this work, we apply a method known as the attainable region (AR) technique in order to optimize the milling and leaching process of a low grade gold ore. No work on the application of the AR optimization technique has been done yet on a joint milling and leaching process. The advantage of the AR approach lies in its ability to simplify the optimization problem, as searching over a defined set for the maximum of an objective function is a fairly standard procedure. The objective function we selected was that of optimizing a linear function of the value of the recovered material minus the cost of both milling and leaching. Using the three variables (milling time, leaching time and recovery), we constructed a 3D plot and used it to obtain all the possible recoveries from the different milling and leaching times. The optimum for our chosen objective was then found by overlaying a contour plot of the objective function on the 3D plot. Our results show that the optimum was obtained at 90 % recovery with a profit value of 600, milling time of 30 minutes and leaching time of 1750 minutes.INTRODUCTIONAfrican countries are facing a general increase in demand for electrical power. In South Africa, the demand is now surpassing the supply from ESKOM, the main electric power provider of the country. This has resulted in load shedding strategies being implemented in many local communities in an attempt by ESKOM to cope with the high demand. A potentially better approach is to propose use of energy efficient technologies in the country’s largest power consuming industry; the mineral processing sector.In mineral processing, milling is the highest consumer of energy. The objective of carrying out milling is not merely to reduce the particle size of the feed material, but also to liberate the constituent minerals that make up an ore. This is done so that valuable minerals can be separated from the gangue, in downstream processes, such as leaching. However, the milling process is generally performed relatively poorly, and at a considerable expense in terms of electrical power utilization. Tomanec and Milovanovic (1994) estimated that milling accounts for more than 50 % of the total power used in the concentration process, but this can rise to as high as 70 % for hard or finely dispersed and inter-grown ores. Apart from being relatively wasteful of energy, the milling process is also inefficient with regard to mineral liberation because of the indiscriminate nature of the grinding force."

Jan 1, 2016

By Will H. Coghill, Fred D. DeVaney

THE coercimeter, as its name implies, is an instrument for measuring the coercive force[+] of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub- sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. The turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1938

By K. J. Powers

The Mine Accident, Injury, Illness and Employment Database at the Mine Safety and Health Administration's Health and Safety Analysis Center is a computerized system that stores accident, injury, illness and employment data about all coal and metal/nonmetal mines in the United States. The paper discusses the system for collecting, storing, analyzing, and reporting this information and how these data are used in the ongoing effort to increase the health and safety in this nation's mines.

Jan 1, 1983

By O. E. Brown

The measurement principle of the Coulter Counter for particle size analyses is described. The application of the Coulter Counter to cement particle content and size analysis and to the size distribution of clinker from standard grindability tests are described. Methods of calibration, sample preparation and data reduction are presented. The results of the analyses obtained are compared with characteristics associated with performance showing both concordance and non-concordance of test data., Future uses of the Coulter Counter for particle size analysis in research and plant control adaptations are indicated.

Jan 1, 1960

By Dalila Chaves Sicupira

A pitting corrosion study of welded joints of lean duplex stainless steel (LDSS) UNS S32304 has been performed. LDSS S32304 thick plates were welded by different processes commonly employed in equipment and piping construction: SMAW (Shielded metal arc welding), GMAW (Gas metal arc welding) and FCAW (Flux cored arc welding). The electrochemical behavior of different weldment zones (fusion zone (FZ), base metal (BM) and heat affected zone (HAZ)) was characterized both independently using an electrochemical microcell and together through whole sample analysis. The electrochemical method applied was performed in acidified glycerin, a process fluid of the biodiesel industry. The results were correlated to the microstructural features of the materials. Based on the results, is possible to conclude that the breakdown potential (Eb) of the fusion zone (FZ) was higher than the Eb obtained for the heat affected zone (HAZ). In general, top samples show higher breakdown potential than root samples and also the samples welded using filler metal 2209 has a better anodic behavior than the filler metal 2307. According to the results, GMAW welding process with 2209 as filler metal was revealed as the optimum chosen for application of 2304 duplex stainless steels in this case.

Jan 16, 2018

By H. Ewaschuk

"INTRODUCTIONRio Algom's involvement with the Enviro-Clear thickener began in May 1975, when tests on a laboratory waif were carried out by our Research and Development group. Commencing in June, further tests were carried out using a 3 foot diameter pilot unit. By December, a 30 foot full-scale thickener had been installed. In the near future, 3 more Enviro-Clear thickeners will be commissioned. With in the space of a year, almost $2.5 million had been committed to liquid/ solid separation facilities using the Enviro-Clear thickener. This paper briefly traces the extent and development of this commitment.BRIEF HISTORY OF QUIRKEQuirke Mine started operating in September 1956 at a rated capacity of 3,000 TOD. Because of market conditions, Quirke was shut down in December 1960. The facilities were re-opened at an increased capacity of 4,000 TPD in July 1968, by which time the demand for uranium had returned. Also, a second shaft was sunk, and by 1970, all of the ore treated in the concentrator was coming from the new Quirke II mine. The Quirke I stopes were allowed to fill with natural seepage. As well, acidic barren solution from the concentrator was pumped underground.With increasing demand for uranium, the capacity of Quirke will be further expanded to 7,000 TPD by 1978. Studies of how this expansion could best he carried out led to the consideration of a fairly new piece of equipment, the Enviro-Clear thickener, for certain operations in the concentrator. These operations are as follows:"

Jan 1, 1977

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Respirable crystalline silica (RCS) found in dust generated by various mining processes is an important occupational hazard in the underground coal-mining industry. Exposure can lead to disabling and incurable diseases, including coal workers’ pneumoconiosis (CWP), silicosis and lung cancer [1,2]. Clusters of rapidly progressive CWP have been observed in the Appalachian regions of eastern Kentucky and southwestern Virginia, and recent cases have been generally more severe and showing more rapid progression. CWP is approximately four times as common among long-tenured underground coal miners in central Appalachia than long-tenured underground miners in the rest of the United States, and 20.6 percent of long-tenured underground miners in central Appalachia were suffering from the disease as of 2017.

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Exposure to respirable crystalline silica (RCS) can cause serious and irreparable negative health effects, including silicosis and lung cancer. Workers in coal mines have the potential of being exposed to RCS found in dust generated by various mining processes. The silica content of respirable dust in one single mine can vary substantially over both time and location. The current monitoring approach for RCS relies on the use of traditional air sampling followed by laboratory analysis. Results generated using this approach are generally not available for several days to several weeks after sampling, and this delay prevents timely and effective intervention if needed. An alternate analytical method is needed to reduce the time required to quantify the RCS exposure of mine workers. The National Institute for Occupational Safety and Health (NIOSH) has developed a new method using commercially available portable infrared spectrometers for measuring RCS at the end of the sampling shift. This paper will describe the application of the new field-based RCS analytical process for coal mines, including the use of the new method with the existing Coal Mine Dust Personal Sampler Unit. In a case study conducted by NIOSH with a coal mine operator in West Virginia, field-based RCS analysis was completed at a mine site to evaluate the new technique. The RCS analysis results obtained by the field-based method in this case study showed sufficiently strong correlation with results obtained by the MSHA standard laboratory analysis method to allow the mine operator to use the field-based method for evaluating process improvements.

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Exposure to respirable crystalline silica (RCS) can cause serious and irreparable negative health effects, including silicosis and lung cancer. Workers in coal mines have the potential of being exposed to RCS found in dust generated by various mining processes. The silica content of respirable dust in one single mine can vary substantially over both time and location. The current monitoring approach for RCS relies on the use of traditional air sampling followed by laboratory analysis. Results generated using this approach are generally not available for several days to several weeks after sampling, and this delay prevents timely and effective intervention if needed. An alternate analytical method is needed to reduce the time required to quantify the RCS exposure of mine workers. The National Institute for Occupational Safety and Health (NIOSH) has developed a new method using commercially available portable infrared spectrometers for measuring RCS at the end of the sampling shift. This paper will describe the application of the new field-based RCS analytical process for coal mines, including the use of the new method with the existing Coal Mine Dust Personal Sampler Unit. In a case study conducted by NIOSH with a coal mine operator in West Virginia, field-based RCS analysis was completed at a mine site to evaluate the new technique. The RCS analysis results obtained by the field-based method in this case study showed sufficiently strong correlation with results obtained by the MSHA standard laboratory analysis method to allow the mine operator to use the field-based method for evaluating process improvements.

By Moore R

An intensive safety campaign at Mount Isa Mines Limited from 1956 to 1966 saw the lost time accident frequency rate fall to half its original level. A review of the safety programme was carried out in 1967 and in 1968 the Five Point Safety System was introduced. The seven years since its introduction have been years of significant achievement both in production and safety. Improving safety is a fundamental part of Mount Isa Mines Limited's policy and this system has been a major tool in implementing that policy. To be successful personnel need to be prepared and trained for its introduction and subsequently counselled on its use. A carefully prepared programme is required to phase in various aspects of the system and to make use of complementary steps. The system has been a success and it is anticipated that the continued drive to improve the use of principles of the system will further improve safety. It is hoped that this paper will be of value to those personnel concerned with industrial safety in Australia.

Jan 1, 1975