Search Documents

By Shelley M. Burg, Dennis K. Poulton, Robert B. Gordon

This project includes the excavation and concrete lining of approximately 18 900 m (62 000 ft) of 5.5 m (18 ft) finished diameter subway tunnel for the Los Angeles MTA. The project required that four soft ground headings be excavated from a single shaft located near the mid point of the tunnels. The tunnels were classified "gassy" during the excavation phase. Because of the contract schedule requirements and the limited urban work site available, many logistical problems had to be overcome during the project while excavation was accomplished at a record setting pace. Some unique project features include the muck handling system and an access shaft using a high strength tieback support system. In order to accomplish the work, an extensive effort to plan and construct the main work site was required.

Jan 1, 1995

By John B. Spencer

Earlier this year, Simplot Phosphates achieved a safety milestone at its Vernal, UT phosphate operations. In March, the entire operation reached achieved seven years without a lost time accident. And the mine operations at Vernal reached the 1 million hours benchmark without a lost time accident. This million hour achievement has been 19 years in the making. This achievement reflects the mine’s strong attitude towards safety, the company said. Safety is an integral part of its culture and requires diligence and considerable work. Attention to even the smallest of details cannot be allowed to slip. This is a record Simplot Phosphates said it hopes to improve on every day.

Jan 1, 2004

Jan 1, 1982

By J. R. Weber, R. D. Haddenham, J. H. Bailey

Introduction The Vernal Phosphate Operation is located in northeastern Utah, about 18 km (11 miles) north of Vernal, about 280 km (175 miles) east of Salt Lake City, UT. The plant began initial operations in 1961 under the name of the San Francisco Chemical Co. In 1981, Chevron purchased the operation from Stauffer Chemical Co. In 1982, plant capacity was doubled to about 72.6 kt/a (800,000 stpy) of phosphate concentrate. From 1984 to May 1986, another expansion increased the capacity to 1.2 Mt/a (1.3 million stpy) of concentrate. It also incorporated a number of equipment and process changes designed to increase the overall plant phosphate recovery. A 150-km (94-mile) slurry pipeline, the world's longest phosphate pipeline, was also constructed from the Vernal plant to a new Chevron Chemical and Fertilizer plant near Rock Springs, WY. Over the past five years, plant expansions and the pipeline construction have been accomplished without missing a single concentrate shipment.

Jan 1, 1987

By A. C. Alexander

Chevron Resources Company owns and operates an open pit phosphate mine and mill 11 miles north of Vernal, Utah. The plant currently produces 500,000 tons per year of concentrate and has the capacity to produce 750,000 tons per year. The operation is currently being expanded to 1,300,000 tons per year of concen¬trate in order to supply a new fertilizer plant being constructed by Chevron Chemical Company in Rock Springs, Wyoming. A 10-inch, 96-mile pipeline is being built to transport the concentrate from Vernal to Rock Springs. The present and expanded operation will be discussed. HISTORY In 1915, Harry Ratliffe staked nearly 15,000 acres of low to medium grade phosphate rock along the southern flank of the Uintah Mountains. This deposit became the largest privately owned phosphate deposit containing approximately 700 million tons of reserves. Initial development of the deposit began in 1958 by San Francisco Chemical, a joint venture between Stauffer Chemical Company and Mountain Copper Limited. In 1968, Stauffer Chemical Company bought out Mountain Copper Limited and became sole owner and operator. In 1981, Chevron Resources Company bought the property from Stauffer and has operated the mining and milling operations since.

Jan 1, 1985

By V. Niemitz

Approximately 30 miles east of Chicago on the southern shores of Lake Michigan stands Bethlehem Steels newest fully integrated steelmaking facility-the billion dollar Burns Harbor plant. The first phase of what will ultimately be the most completely integrated and flexible materials handling system for a steel mill in the western hemisphere is now complete.

Jan 1, 1970

Traditionally, the predominant drilling method in open pit mining has been large hole rotary drilling using cumbersome, inflexible equipment offering merely limited scope for improvements in pit design and overall costs. By contrast, the recent development of comparatively light high-pressure down-the-hole hammer crawlers has paved the way for new ideas and trends. High penetration rates coupled with superior mobility and fast set-ups contributing to substantial productivity gains have resulted in a renascence for this drilling method in open pits. The ability to cover a wide range of hole diameters and angles gives designers unique drill pattern possibilities especially when establishing steep and stable pit slopes. As pre-split holes, buffer holes and production holes all can be drilled by using the same equipment, there are, there are obvious advantages in production scheduling as well as in materials handling and service. This paper presents some case stories, which will demonstrate the benefits and improvements that the introduction of new drilling methods and equipment has brought to open pit mining operations.

Jan 1, 2003

By Joe Harris

Large structures, such as a multistory office building or a large storage tank, are constructed the most economical way possible, which may involve a shallow foundation system placed on native soil or compacted fill material. Over the life of the structure, the foundation system may not perform as originally anticipated, leading to differential settlement. Minor differ- ential settlement is expected; however, settlement that exceeds allotted tolerance can render the structure inoperable. Compaction grouting is a well-known and accepted ground improvement technique that can be used to not only stabilize but relevel multistory buildings and large dia- meter storage tanks. Two projects, each with differing types of structures, were successfully remediated utilizing com- paction grouting as the primary method to remedy settlement.

Sep 1, 2023

By Richard Woodward

Presentation Outline ?What types of coal analyzers are there? ?What do they measure? ?How do they work? ?How accurate are they? ?Most common applications ?Sorting ?Blending ?Prep plant optimization ?Boiler Control

Jan 1, 2006

By David Kwietnewski

Roadheaders are gaining widespread acceptance in North America as a means for mechanical tunnel excavation. Until recently, almost all of the large-scale North American tunnel projects were excavated one of two ways ? the tried and true drill-and-blast method or with the use of tunnel boring machines (TBM), the hi-tech super-excavators. TBMs enjoyed fast-growing popularity worldwide as TBM manufacturers offered greater technology to meet the demand of the civil tunnel industry in the late 20th century. Recently, though, more tunnel projects, large and small, can thank the brute force of a roadheader for getting the job done.

Jan 1, 2011

By D. Kwietnewski

With all of the unknowns associated with tunnel construction, how does a contractor choose a roadheader? This paper presents a review of several models of roadheaders being used in today?s tunnel projects. The features of different models of roadheaders are presented and compared. Roadheader size and cutter power generally determine which roadheader is best for a particular job. We will also present a model for matching features of the roadheader to the anticipated ground conditions such that the most efficient machine is selected for the project.

Jan 1, 2011

By Alan D. Hoagland

The Flat Gap Mine is on Copper Ridge in the Appalachian Valley of East Tennessee, Large zinc orebodies occupy zones of solution and collapse breccias in lower Ordovician Kingsport limestone and dolomite, The principal ore mineral is sphalerite and the principal gangue is dolomite, The orebearing horizons are considerably more than 95% covered by thick residual clay, and geochemical prospecting under these conditions is an effective exploration technique which played an important role in the discovery and exploration of the Flat Gap Mine, The residual nature of the over-burden at Flat Gap is emphasized, Background heavy metals (mainly zinc) range from 50 to 200 ppm, and the anomalies range to 3000 ppm and more, About 80% to 9W0 of the soil zinc is in relatively insoluble form in solid solution with the hydrous iron oxides and in the crystal lattice of the clay minerals. Quite discrete zones in the soil with sharply contrasting metal value boundaries mark vestiges of bedrock mineralization, and such anomalous soil areas are often contiguous with partially weathered ore. It has not been possible on the basis of chemical criteria to distinguish between an anomaly formed from non-commercial mineralization and one formed from ore.

Jan 1, 1962

By Arthur Foote

AT THE end of the year 1914, the main North Star incline shaft had reached the 6300-ft. level, and encountered a vein dipping Southwest, or, exactly opposite to the North Star. Subsequent development failed to find the North Star vein continuing beyond this intersection, so the 6300-ft. level proved to be the bottom level of the North. Star vein, and very little ore was found below the 5300-ft. level. The new vein was called No. 1 vein. Development work carried on for the next 10 years discovered a third vein, called No. 2, branching off about 1200-ft. to the east, with a North-south strike and a west dip. No. 1 vein had about 900 ft. of backs above the 6300-ft. level before reaching the boundary line of the property, and No. 2 vein died out about 800 ft. above. During these 10 years, the money spent on development was increased from $54,000 in 1914 to $184,000 in 1924; the ore reserves steadily diminished until it was evident that the mine must close down unless by some means a large tonnage of ore could be developed quickly.

Jan 1, 1930

By M Lee, J F. Carswell, G Reitsema

"The increased costs of underground mining have continually challenged engineers to identify opportunities for alternatives to common approaches to underground development. Considerations to the design of horizontal and vertical development at the Dugald River mine targeted inclined raise boring to reduce horizontal development, not only to reduce cost, but to allow development activities to focus on other areas of the mine.The mine plan consists of 50 raise bored ventilation shafts, of which 17 have been mined to date with diameters ranging from 3.1 m to 5 m and lengths from 30 m to 200 m. The expected performance and stability of these shafts has been determined using methodologies proposed by McCracken and Stacey (1989) and further refined by Peck, Coombes and Lee (2011). Actual raise performances have been collated and compared to a database of raise bore performances across Australia as presented by Coombes, Lee and Peck (2011), and form a database of raise bore performance specific to Dugald River.Opportunities to further optimise the mine plan and reduce costs have seen the introduction of large diameter-inclined raise bored ventilation shafts to minimise the required lateral development to connect the ventilation circuits. Large diameter inclined shafts ranging between 3.1 m and 4.5 m in diameter have been successfully mined with dips down to 70°, reducing the cost of lateral development by more than $1 million over the next two years.Both technical and operational challenges were overcome in the mining of large diameter-inclined raise bores, including modification of: existing methodologies of assessing shaft wall stability for inclined raises. These included variations of the McCracken and Stacey method and the utilisation of the modified stability number (N’) previously developed for stope performance (Potvin, 1988). both the collar and toe development profiles, including the general set-up of the raise bore drill rig to reduce the operational risks associated with angled raises.Due to their success, inclined raises have been designed for subsequent stages of the life-of-mine ventilation system at Dugald River. This has resulted in significant capital cost savings for the mine.CITATION:Carswell, J F, Reitsema, G and Lee, M, 2017. Vertical and inclined raise bore performance at Dugald River mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 313–320 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By G. Price

The Building Research Establishment installed a base load cell in a driven cast-in-place pile prior to it being tested under vertical load. The monitored base loads were found to be significantly less than could have been predicted by current design methods. The less than expected capacity was attributed to the drilling out procedure. An electro-level system installed in a second similarly formed pile, provided detailed information on the performance of the pile under lateral load. The information obtained was used to check several current design methods for laterally loaded piles. The findings show the potential dangers of attempting to improve design parameters from only limited performance data.

Jan 1, 2010

By Catherine T. Aimone-Martin, Brent Meins

Blast vibration monitoring for buried pipelines is typically conducted at the ground surface with a shallowly buried geophone. In many jurisdictions across the U.S., blast-related vibration limits set for pipelines are dictated by surface measurements and do not consider the significant reduction of PPV amplitudes acting on the pipe at depth. This study involved a vertical array of geophones deployed in drilled holes at two blasting sites of the Loop 202 South Mountain Freeway construction project in Phoenix, Arizona. City of Phoenix pipeline engineers were concerned that blasting would damage an aged 48-inch (122 cm) prestressed concrete cylinder pipe (PCCP) that serviced water for South Phoenix

Jan 1, 2019

By Michael E. Ameel

The vibrated beam method of installing a vertical barrier wall is one of the least applied techniques, yet given certain site conditions and constraints, it is a cost-effective and proven method of controlling lateral groundwater flows. A recent full-scale application of this technique demonstrated its usefulness at an active manufacturing facility located in Northern Wisconsin. At this site, a 3,233 foot long cutoff wall was keyed into an underlying bedrock, which was located an average of 40 feet below the ground surface. Using a slag cement-clay based slurry, a 1E-7 cm/sec or less, nominal 4-inch wide cut-off wall was constructed using the vibrated beam method. Challenges included working around an active manufacturing facility with minimal access to the work area; installing the wall through a very dense glacial till; minimizing soil excavation volumes of potentially impacted soil; and, working around and adjacent to numerous active utility lines without impacting the facility operations. At utility locations, the vibrated beam wall was supplemented with a jet grout panel wall, without the need to bypass or otherwise interrupt any of the plant?s utilities. Quality control consisted of the monitoring and measuring of slurry parameters, survey control, and real-time monitoring and documentation of all critical barrier wall installation parameters. A vibration monitoring plan was also implemented to measure vibrations at utilities and adjacent facility structures. Proper equipment selection, significant up-front planning and close coordination with the facility resulted in a safe and successful project. The work was completed ahead of schedule during the 2009 construction season.

Jan 1, 2010

By Hitoshi Ogura, Koichi Kobayashi, Sadao Yabuuchi

"In Japan, most pile foundations using pre-cast concrete piles are installed by the bored pre-cast piling method, wherein pre-cast piles are installed in holes that have been excavated beforehand and filled with cement milk (term used for cement water slurry in Japan). The bored pre-cast piling method with enlarged base, in which the portion near the toe is enlarged during boring operation, is widely used because of the cost benefits and the increased vertical bearing capacity that this method offers.The EX MEGATOP method, further developed as an improved bored pre-cast piling method with enlarged base, is reported here. The features of this method are: (1) High vertical bearing capacity; (2) High degree of freedom in design; (3) Excellent workability; and (4) Friendly to the environment. In particular, high vertical bearing capacity can be obtained using nodular piles and by enlarging the area at the pile toe and shaft. This method can gave a vertical bearing capacity coefficient at the toe of a=430, more than twice the corresponding value of a = 200 of a conventional bored pre-cast pile. Moreover, the shaft resistance can be several times larger than that of a conventional bored pre-cast pile. This report gives an overview of the EX MEGATOP method, evaluation of vertical bearing capacity, and examples of application of the method.1.lntroductionMost pile foundations in Japan are installed by the bored pre-cast piling method, that is, in holes that have been excavated beforehand and filled with cement water slurry, referred to as 'cement milk'. The ""bored pre-cast piling method with enlarged base"" is frequently used. In this method an enlarged excavation is used near the pile toe to increase the vertical bearing capacity.The EX MEGATOP method is a variation of the bored pre-cast piling method. Its features include the use of nodular piles and a long, enlarged excavation. The vertical bearing capacity of the EX MEGATOP method is described in this report."

Jan 1, 2005

By Steve Crewdson

High tonnage hoisting of materials by vertical conveyors through deep shafts is a relatively new concept in mining that is proving to be effective. The development of the Pocketlift® belt by Metso Flexowell, located in Moers, Germany, enabled the installation of a deep shaft vertical conveyor in 2002. This application followed years of design and operational experience gained in medium-depth shafts around the world. The design, manufacture, installation and operational experience of an 1,818 tonnes capacity, 273 meters vertical lift, Pocketlift® belt system at the White County Coal Pattiki 2 Mine is the subject of this work

Jan 1, 2004

By I. Melik-Gaykazov, N. N. Melnikov, V. A. Fokin, S. P. Reshetnyak

Kola Mining Institute has been carrying out investigations of the possibility to steepen the walls of the Kovdor open pit with the design depth of 600 m. Steeping (up to 60°) wall angles is done by double height (24 and 30 m) benches with vertical slopes. One of the safety factors of mining with such walls is choosing the width of the safety berms preventing against rock falling from the slopes into the pit working area. The test on rock falling from 24 m benches has shown that vertical slopes are not more dangerous compared to the inclined(60-75°) ones.

Jan 1, 2003