Search Documents

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999

By W. A. Eardley

FIFTEEN years ago the world's deepest oil well penetrated the earth about 7300 ft. That depth has now been more than doubled. Why has such deep drilling become necessary and how has it become possible? Three factors have had an important bearing: (1) Depletion of shallow zones, making it necessary to search for deeper producing measures. (2) The perfection of prospecting methods, which have been success- fully used to locate favorable buried structures, many at great depth. (3) Improvement in the quality of steels used for drilling.

Jan 1, 1940

By A G. Guinea

If you were reading this article in a newspaper or similar in the 1800s, you would know that the world was firmly in the grip of the Industrial Revolution. You might have been one of the families that decided that an agriculturally based existence was no longer for you, and that the promise of a factory job was more appealing and more secure. And it was. Financially at least. Not so much from a workplace safety perspective.

May 5, 2022

By Y Potvin

Underground mines in Australia are progressively operating at greater depth, sometimes in conditions where mine induced stresses are very high. In such conditions, the seismic activity often becomes intense and violent and in response, mines must develop and implement a sound rock burst risk management strategy to continue operating safely.This paper discusses the latest techniques successfully used in Australian mines to mitigate the risk of rock bursts. In particular, the paper describes how the analysis of data collected from seismic monitoring systems can provide an understanding of the seismicity and be used for quantifying seismic hazards in the mine. Once an adequate understanding and assessment of seismic hazard has been achieved, the associated risk can be mitigated using different layers of protection.Strategically, modifying the mining method, the extraction sequence and/or the mining layout can alleviate the seismic hazard, but these solutions generally cannot be implemented rapidly. In the short-term, seismic risk can be mitigated tactically using an energy absorbing support system or to remove personnel from being exposed to rock burst damage by implementing exclusion zones.

Mar 21, 2011

By Eric R. Achelpohl

The paper follows the introduction of a college student into the explosives industry. The opportunity of experiences from classes and work at the University of Missouri-Rolla, along with summer internship experiences are highlighted.

Jan 1, 1998

By E. C. Skinner

As the program says -we'll he talking about the expectations of the Management of an Industrial Mineral enterprise relative to the activities of geologists engaged in that enterprise. Industrial Minerals is such a large industry both in tons produced and in value of product -and of such diversity and complexity of participating enterprises, minerals and products that I doubt if anyone person can speak for the entire industry as to the expectations of management with respect to the geologist. I'm sure there are major differences in emphasis between segments of management as to the relative importance of the different aspects of the geologists' role in the scheme of things. However, we will try to generalize concerning what we consider to be important factors and to be more specific perhaps of some of the factors with which we have had direct assessable experience.

Jan 1, 1972

By John J. Schanz

THE highly publicized shortage of students enrolled in engineering curricula has brought about a rapid increase in the enrollment in engineering schools in many parts of the country. Though most of the various curricula in the mineral industries field have participated in this increase, the experience at Pennsylvania State University has been that the nonmineral types of engineering have been increasing at a much more rapid rate than those in the College of Mineral Industries. [ ] It has been a matter of some concern to the staff of the College of Mineral Industries that enrollment in the curricula of the school has not been increasing at a rate commensurate with that experienced in the College of Engineering. If the lack of trained young graduates for our vital mineral industries is to be overcome, this situation must be remedied.

Jan 8, 1954

This paper will address this question from the point of view of a drill and blast engineer or researcher working in open cut and underground mining operations. The paper will establish a common set of reference standards for high-speed imaging and data capture, which engineers and researchers can apply when deciding which type of imaging technology is appropriate. It will present an overview of current image analysis technologies and practices in use across a range of appropriate scientific fields and draw lines of commonality of approach between these fields and the field of mining and blasting applications analysis and research. In addition, the paper will examine the different technologies from an image quality and data stream reference point, ease of operation, cost, and reliability parameters. Finally, this paper will present an argument for the hybridisation of established and new technologies which could provide a more beneficial approach to the use of imaging as a tool of quality control, research and analysis in the mining based industries. This will include a novel approach to digital high-speed imaging and data analysis in the field, which should deliver high-quality images and data analysis in a time frame that is more appropriate to the need for immediate action, analysis and problem solving.

Jan 1, 2007

By R. A. Matuszak

In recent years, a new concept in the control of electrically powered excavators has come into existence. The new type of control system has come to be known as "static" control. The use of the name "static" to describe this system is somewhat misleading since this term refers only to one of the many advantages of this very important advance in excavator control systems. In 1959, the first truly "static" control for Ward-Leonard equipped electric excavators was designed, developed and placed in service. The control system, originally intended only as a more modern electronic type of alternate to the tried and proven rotating amplifier control system then in use, has since proven to be much more.

Jan 1, 1964

By Francis Cameron

Mining is both exciting and rewarding-although at times somewhat frustrating-and we all can have real pride in our industry, in its people, and in its accomplishments. It is, however, with concern that I have noted a deterioration in this Country in what might be called mining's stature and in the growth of a belief in many quarters that our mineral reserves are rapidly approaching exhaustion. In other words, there is a popular image that we are fast becoming a "have not" nation in many respects and that the domestic mining industry can no longer be considered, in the vernacular of Wall Street, to offer much in the way of "growth potential." I do not subscribe to this hypothesis, nor do I believe that the record of the mining industry bears this out. However, let me add that we can, in time, talk ourselves into this frame of mind and we can hasten the day when this very well might come about by unnecessary and unwise legislation or regulation. My remarks today are basically designed to give my reasons for refuting this negative philosophy and to review our record. With your help, I know we can improve our image, and the public's recognition of our industry's peculiar problems.

Jan 4, 1968

By Rossiter W. Raymond

(Read at the Amenia Meeting, October, 1877.) THE term "pipe-vein" has recently been applied in this country to certain deposits of lead ore in magnesian limestone. The use of the term has been twofold. It has been revived as a term found in textbooks on mineral veins, with the implied or declared assertion that the ore-deposits thus named in this country are similar to those which have borne the title abroad. It has also been advanced as an appropriate name for a new class of deposits, even if such a class had not previously been recognized. In either case, the assumption is that pipe-veins form a group or class by themselves, and are not merely interior and subordinate features in larger deposits. The peculiar mining law of the United States, which regards " the vein," whatever that may be, as the basis of title, lends a special interest to these claims. But the object of this paper is rather to discuss the subject from the standpoint of geology and technical literature. I shall briefly answer two questions : (1) What are pipe-veins as described in technical literature? and (2) Is the name appropriate or necessary for a new class of deposits ? The term "pipe-ore," as applied, for instance, to irregular, cylin-

Jan 1, 1878

By I. Jones

Geologists, engineers, technicians and surveyors have successfully utilized technical software in the mining industry for over 30 years. Software for processing survey, geology, mine engineering and planning information make these functions more efficient by automating repetitive tasks and reducing data processing errors. While these systems have been improved incrementally overtime, new systems that represent giant leaps in technology have been introduced to help mining operations increase productivity and reduce costs. However, their widespread use within the industry has left individual companies without a competitive advantage. Additionally, the ability of these applications to provide the productivity improvements required in today’s uncertain market conditions has since peaked. The next wave of technology—integration of independent software applications—is just starting to emerge and will have a significant effect on the productivity of mining operations. To reap the productivity gains required to remain competitive, mining companies must exploit the collective knowledge and experience of every employee in the organization. Integration of independent software application allows companies to leverage information from all activities, enabling staff to make better decisions to improve productivity. This paper outlines the importance of integration as productivity enabler. Key performance indicators, strategic mine planning, resources management and mine-to-mill integration are discussed as processes that enable productivity. The Gemcom Enterprise Mining System (GEMS)is introduced as the industry’s first integrated solution that enables these productive processes. The paper concludes with a comment on the level of change required to realize the benefits of integration.

Jan 1, 2003

By Adam Bedell, Brad Crenshaw

Tunnel project contract documents often present groundwater infiltration requirements for components of the underground portions of the project. All too often these documents require quantifiable target inflows for these components, but only refer to them in subjective terms such as “dry,” “manageable,” etc. The Contractor’s definition of these terms will inevitably differ from the Engineer’s definition of these terms. The purpose of this paper is to look at common subjective terms used in documents and provide suggestions for reasonable quantifiable language. Additionally, the paper will provide information and recommendations on relative levels of cost and effort increase needed to provide increasing levels of water cutoff (i.e., achieve “dryness”?).

Dec 1, 2022

Miners and explorers in New Zealand are expected to consult with stakeholders, keep out of core conservation areas, and operate a high standard of environmental management and rehabilitation. These requirements are not difficult to meet, but many of the industry's own actions have brought it to a low level of general public esteem in New Zealand. Reasons for this are discussed, drawing examples from the Maruia Society's experiences with the industry since the mid-1980s. The boundary between core conservation areas and other land is not easily drawn, and the Maruia Society has sought to work with the mining industry to promote legislation for net conservation benefit trade-offs. However this initiative was not successful. Today the industry, unlike most other major industry sectors in New Zealand, has no accord with the country's conservation movement.

Jan 1, 1997

What is experience worth? Representatives from the Mining, Metallurgy and Petroleum Societies discussed the question as part of the 1970 Annual AIME Meeting held in Denver, Colo. the week of February 15. Petroleum engineer-consultant, Michel T. Halbouty of Houston, Tex. offered his own clarification of present-day employer-employee relationships in engineering as a whole. "Longevity does not equal experience on the job. Further, when employees are considering salary increases and promotions, job performance is considered all the time; experience two- thirds of the time and length of employment one- half the time." He added, "worth is really what the employee can get for it and experience is essential to survival." Halbouty also noted that salary and responsibility is a function of man's value to his company and is about "as discrediting as grey hair." As far as the engineer is concerned, he reported, the company's ability to pay is, in large measure, not considered. From the company's viewpoint, however, the employee is expected to learn his first year on the job. His second year, he is expected to make his presence felt, Should he require three years to orient himself he might soon be looking for another job. The petroleum engineer pointed out that when the employee wants to know why the salary scale tends to plateau off in later years, most employers react by recognizing that employees "flatten themselves rather than the company flattening them."

Jan 1, 1970

? A roof bolter reaches for a lever while guiding the drill with his other hand. Since he's watching the drill and many of the controls look and feel alike, he hits the wrong control and crushes his hand. ? Six hours into the night shift, an ore truck driver dozes off. The truck plows over the berm and down into the pit. ? Fleeing a afire, a face crew sees smoke in the intake entry. Assuming the fire is ahead, they cross over to another entry, but soon encounter even worse smoke. These very different accidents have at least one factor in common: the human factor. The actions, decisions, thoughts, or perceptions of one or more humans contributed to the accident. These are just a few examples of safety problems researched by the Human Factors Group of the Pittsburgh Research Center, U.S. Department of Energy.

Jan 1, 1998

By Skinner W, Netting A. K O

Surface analysis of ore samples collected from corresponding concentrate and tailings process streams is now a widely used tool in many Australian base metal sulphide concentrators, particularly those involved in AMIRA projects. The use of tec

Jan 1, 1997

By A Scott, A C. Torrance

Explosive properties are typically summarised on manufacturers’ technical data sheets. The values most commonly referred to are the density of the explosive, the energy it is expected to release and its velocity of detonation (VOD). This information is provided so that blasting engineers can make a considered selection of the most appropriate product for a particular blasting application. As an example, a lower VOD and energy product is better suited to blasting in soft, weathered material. In contrast, blasting hard, competent material generally requires a higher energy product which is usually characterised by higher VOD and energy.A review of the technical information supplied by manufacturers shows a wide range of methods of reporting both VOD and energy. A meaningful comparison between products from different suppliers is almost impossible to achieve based on these data. For a similar product, one supplier may have a VOD range of 2800–5800 m/s and a relative bulk strength of 1.34 while a corresponding product from another supplier is quoted with a VOD range of 3100–6300 m/s and a relative bulk strength of 192. In the end, the user has to rely on the level of confidence available from their experience using a certain type of explosive in the type of rock to be blasted at that mine.This paper reviews some of the technical and supporting information that is freely available in the literature and attempts to provide some clarity as to what the numbers that are reported actually mean for the end user. An alternative approach to the evaluation of the suitability of a given explosive to blast a given rock mass is proposed.CITATION:Torrance, A C and Scott, A, 2015. What is relative about energy?, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 447–454 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M Dickie

During the 1980s and early 1990s low cost gold treatment plants were at the forefront of the Australian engineering and mineral processing business. This opportunity was the result of a high gold price and innovative design by emerging engineering companies in an expanding market. The low cost approach to gold plant design and project execution resulted in smaller and shorter life projects becoming viable and the multiplicity and fast track approach of the projects resulted in sharp learning curves. From the mid 1990s to the early 2000s the relatively low commodity prices and resultant reduction in minerals opportunities also resulted in innovative design in both small and large plants, albeit on a reduced scale. The innovation was associated with alleviating capital cost pressures for large capacity low-grade (eg NewcrestÆs Cadia) or small-scale (eg JubileeÆs Cosmos) projects to either improve NPV or to enable the project to be won and profitable in the competitive lump sum environment. Between 2004 and 2008 the engineering market became less competitive from an engineerÆs perspective due to the high demand for engineering services in a high price commodity market. The need for innovation remained but was driven overtly by shortages in water, power and personnel and long equipment lead times. This paper discusses some of the factors that contribute to the capital cost of a project and the scope for improving the likelihood of financing and increasing the project net present value (NPV). Case studies with recent large copper concentrator projects will be used to demonstrate how a value driven approach to project and plant layout can result in significant improvement in NPV.

Jan 1, 2009

By Albert Sauveur

As THE years go by, names of distinguished metallurgists will be added to the list of Henry Marion Howe lecturers, and now and then an illustrious one, for to be chosen to deliver the Howe lecture will be, I do not hesitate to predict, a highly coveted honor. I pray, therefore, your indulgence, if I confess to a feeling of gratification in having been appointed the first of these lecturers. It does not follow, however, that I am losing all sense of proportion and that I have an exaggerated idea of the little I have been able to contribute to our knowledge of iron and steel. Indeed, I fully realize how small were my claims to so great a distinction. I realize, also, that those entrusted with the task of selecting a lecturer were actuated, in coming to a decision, by their knowledge of the long and intimate friendship that had existed between the leader we have lost and myself. For their generous impulse, I thank them from the bottom of my heart; and with becoming modesty, I take up my task as the first Henry Marion Howe lecturer. It would be pleasant and indeed most appropriate to devote this entire lecture to a eulogy of Henry Marion Howe and his work, but how short the time for so large an undertaking and how inadequate my qualifications! On Aug. 28, Sept. 4, 11, and 18, 1875, a series of articles appeared in the Engineering & Mining Journal entitled "What is Steel?" With one exception, these constitute the first professional paper of Henry Marion Howe. That was nearly fifty years ago, three years after graduating from Harvard University. He was then but twenty-seven years old and already his keenly inquisitive mind was actively at work. There is a touch of romance in this young metallurgist who, on entering his. scientific career, destined to be so brilliant and so fruitful, on the very threshold of it, seems to have selected as his motto "What is Steel?" Like a knight-errant of science, he started on his quest for an answer to that question, a quest which was to last forty-seven years and which death only brought to an end. And while thus engaged how many wonderful messages we received from him, each one bringing us nearer to the goal! How illuminating, inspiring and encouraging were those messages! How well-equipped he was to wrench from nature some of the secrets she so jealously guards! How broad his learning and how clear his

Jan 5, 1924